hello, anyone can provide me a clue how to change bootloader on this box?
on jtag , i not see corect device in chain.
there is other way, to upload?
i have the compiled uboot for device.
Thanks.
(Last edited by cornelus2009 on 18 Sep 2014, 15:11)
Topic: Arcadyan Experia Box v8 (VGV7519)
The content of this topic has been archived on 24 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.
Page 1 of 1
Hello, succeded to write uboot on flash, downloaded all openwrt builds for this board, but all go stuck at this point
VGV7519 # bootm
## Booting kernel from Legacy Image at 81000000 ...
Image Name: MIPS OpenWrt Linux-3.10.49
Created: 2014-10-02 7:16:28 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1513077 Bytes = 1.4 MiB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.10.49 (bb@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r42625) ) #3 Wed Oct 1 15:47:08 CEST 2014
[ 0.000000] SoC: VR9 rev 1.2
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019556 (MIPS 34Kc)
[ 0.000000] MIPS: machine is VGV7519 - KPN Experiabox V8
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=0002a4ba
[ 0.000000] Readback ErrCtl register=0002a4ba
[ 0.000000] Memory: 60156k/65536k available (3178k kernel code, 5380k reserved, 1127k data, 228k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 500MHz
[ 0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[ 0.032000] pid_max: default: 32768 minimum: 301
[ 0.036000] Mount-cache hash table entries: 512
[ 0.040000] pinctrl core: initialized pinctrl subsystem
[ 0.044000] NET: Registered protocol family 16
[ 0.056000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[ 0.068000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[ 0.072000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[ 0.184000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[ 0.284000] ifx_pcie_wait_phy_link_up timeout
[ 0.288000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[ 0.400000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[ 0.500000] ifx_pcie_wait_phy_link_up timeout
[ 0.504000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[ 0.616000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[ 0.716000] ifx_pcie_wait_phy_link_up timeout
[ 0.720000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[ 0.832000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[ 0.932000] ifx_pcie_wait_phy_link_up timeout
[ 0.936000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[ 1.048000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[ 1.148000] ifx_pcie_wait_phy_link_up timeout
[ 1.152000] pcie_rc_initialize link up failed!!!!!
[ 1.168000] bio: create slab <bio-0> at 0
[ 1.172000] gpio-stp-xway 1e100bb0.stp: Init done
[ 1.176000] usbcore: registered new interface driver usbfs
[ 1.180000] usbcore: registered new interface driver hub
[ 1.184000] usbcore: registered new device driver usb
[ 1.188000] Switching to clocksource MIPS
[ 1.196000] NET: Registered protocol family 2
[ 1.200000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 1.208000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 1.212000] TCP: Hash tables configured (established 512 bind 512)
[ 1.220000] TCP: reno registered
[ 1.224000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 1.228000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 1.236000] NET: Registered protocol family 1
[ 1.240000] gptu: totally 6 16-bit timers/counters
[ 1.244000] gptu: misc_register on minor 63
[ 1.248000] gptu: succeeded to request irq 126
[ 1.252000] gptu: succeeded to request irq 127
[ 1.256000] gptu: succeeded to request irq 128
[ 1.264000] gptu: succeeded to request irq 129
[ 1.268000] gptu: succeeded to request irq 130
[ 1.272000] gptu: succeeded to request irq 131
[ 1.280000] phy-xrx200 gphy-xrx200.5: requesting lantiq/vr9_phy11g_a1x.bin
[ 1.284000] phy-xrx200 gphy-xrx200.5: booting GPHY0 firmware at 38C0000
[ 1.292000] phy-xrx200 gphy-xrx200.5: booting GPHY1 firmware at 38C0000
[ 1.400000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.408000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 1.416000] msgmni has been set to 117
[ 1.424000] io scheduler noop registered
[ 1.424000] io scheduler deadline registered (default)
[ 1.432000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc
[ 1.440000] console [ttyLTQ0] enabled, bootconsole disabled
[ 1.440000] console [ttyLTQ0] enabled, bootconsole disabled
[ 1.452000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[ 1.464000] Amd/Fujitsu Extended Query Table at 0x0040
[ 1.468000] Amd/Fujitsu Extended Query version 1.1.
[ 1.472000] number of CFI chips: 1
[ 1.476000] 3 ofpart partitions found on MTD device ltq_nor
[ 1.480000] Creating 3 MTD partitions on "ltq_nor":
[ 1.488000] 0x000000000000-0x000000040000 : "uboot"
[ 1.492000] 0x000000060000-0x000000070000 : "uboot_env"
[ 1.500000] 0x000000080000-0x000001000000 : "firmware"
[ 1.504000] mtd: partition "firmware" extends beyond the end of device "ltq_nor" -- size truncated to 0x780000
[ 1.640000] libphy: lantiq,xrx200-mdio: probed
[ 1.648000] net-xrx200: invalid MAC, using random
[ 1.652000] eth0: attached PHY [Generic PHY] (phy_addr=0:00, irq=-1)
[ 1.656000] eth0: attached PHY [Generic PHY] (phy_addr=0:01, irq=-1)
[ 1.664000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[ 1.672000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[ 1.680000] net-xrx200: invalid MAC, using random
[ 1.684000] eth1: attached PHY [Generic PHY] (phy_addr=0:05, irq=-1)
[ 1.692000] wdt 1f8803f0.watchdog: Init done
[ 1.696000] leds-gpio gpio-leds.7: pins are not configured from the driver
[ 1.708000] TCP: cubic registered
[ 1.712000] NET: Registered protocol family 17
[ 1.716000] Bridge firewalling registered
[ 1.720000] 8021q: 802.1Q VLAN Support v1.8
[ 1.728000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[ 1.732000] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[ 1.740000] Please append a correct "root=" boot option; here are the available partitions:
[ 1.748000] 1f00 256 mtdblock0 (driver?)
[ 1.756000] 1f01 64 mtdblock1 (driver?)
[ 1.760000] 1f02 7680 mtdblock2 (driver?)
[ 1.764000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)any advices ?
Thanks.
(Last edited by cornelus2009 on 14 Oct 2014, 07:34)
Hi
It could be a corrupt download or "something else"
Dowload again or roll your own image
When we are both on Skype, we will follow http://wiki.openwrt.org/doc/howto/buildroot.exigence so that you can create your own image from trunk and if necessary, change stuff.
I think y should be able to get the developement environment up on yr Ubuntu 10.04, or a virtual box and use ubuntu 14.04
In short
sudo apt-get update
sudo apt-get install build-essential subversion git-core libncurses5-dev zlib1g-dev gawk flex quilt libssl-dev xsltproc libxml-parser-perl mercurial bzr ecj cvs unzip
git clone git://git.openwrt.org/openwrt.git
cd openwrt
./scripts/feeds update -a
./scripts/feeds install -a
make defconfig
make prereq
make menuconfig #This is where y choose board and router
makehttp://wiki.openwrt.org/toh/arcadyan/vgv7519
https://downloads.openwrt.org/barrier_b … ntiq/xway/
https://downloads.openwrt.org/barrier_b … antiq_xway the config file that was used in creation of the images
https://www.dropbox.com/sh/eywont3uni0r … s2009?dl=0 newly compiled images for y 
From Wiki article:
[ 1.760000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[ 1.772000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 1.776000] Freeing unused kernel memory: 188K (803f1000 - 80420000)
[ 2.700000] eth0: port 0 got link
procd: Console is alive
procd: - watchdog -
[ 4.572000] IFXUSB: ifxusb_hcd: version 3.2 B110801
[ 4.576000] Chip Version :01c0 BurstSize=0compared with the last bit of yr boot
[ 1.760000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[ 1.732000] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[ 1.740000] Please append a correct "root=" boot option; here are the available partitions:
[ 1.748000] 1f00 256 mtdblock0 (driver?)
[ 1.756000] 1f01 64 mtdblock1 (driver?)
[ 1.760000] 1f02 7680 mtdblock2 (driver?)
[ 1.764000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)(Last edited by oxo on 15 Oct 2014, 13:59)
The discussion might have continued from here.
Page 1 of 1