Hi evyerone,
i got myself a little mpr a1 clone board (with embedded power supply on it) photo below :
I managed to flash it with MPRA1 build from latest trunk.
Here is the boot log :
U-Boot 1.1.3 (Aug 11 2011 - 14:34:31)
Board: Ralink APSoC DRAM: 32 MB
relocate_code Pointer at: 81fb4000
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 42
spi device id: c8 40 16 c8 40 (4016c840)
Warning: un-recognized chip ID, please update bootloader!
raspi_read: from:30000 len:1000
.*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 3.5.2.0
--------------------------------------------
ASIC 5350_MP (Port5<->None)
DRAM_CONF_FROM: Boot-Strapping
DRAM_TYPE: SDRAM
DRAM_SIZE: 256 Mbits
DRAM_WIDTH: 16 bits
DRAM_TOTAL_WIDTH: 16 bits
TOTAL_MEMORY_SIZE: 32 MBytes
Flash component: SPI Flash
Date:Aug 11 2011 Time:14:34:31
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
##### The CPU freq = 360 MHZ ####
estimate memory size =32 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP. 0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
. Image Name: MIPS OpenWrt Linux-3.14.18
Created: 2014-10-08 14:06:59 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1049941 Bytes = 1 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:100555
................. Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 32
Starting kernel ...
[ 0.000000] Linux version 3.14.18 (vsidou@vsidou-Dell-System-XPS-L322X) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r42840) ) #4 Wed Oct 8 18:06:46 RET 2014
[ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc)
[ 0.000000] MIPS: machine is Poray M3
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00055c80
[ 0.000000] Readback ErrCtl register=00055c80
[ 0.000000] Memory: 29216K/32768K available (2284K kernel code, 119K rwdata, 456K rodata, 140K init, 180K bss, 3552K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 360MHz
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] genirq: Flags mismatch irq 7. 00014600 (timer) vs. 00014600 (systick)
[ 0.010000] Calibrating delay loop... 479.23 BogoMIPS (lpj=2396160)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090000] pinctrl core: initialized pinctrl subsystem
[ 0.090000] NET: Registered protocol family 16
[ 0.120000] bio: create slab <bio-0> at 0
[ 0.120000] rt2880_gpio 10000600.gpio: registering 22 gpios
[ 0.130000] rt2880_gpio 10000600.gpio: registering 22 irq handlers
[ 0.140000] Switched to clocksource systick
[ 0.140000] NET: Registered protocol family 2
[ 0.160000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.180000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.180000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.200000] TCP: reno registered
[ 0.210000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.210000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.230000] NET: Registered protocol family 1
[ 0.240000] rt-timer 10000100.timer: maximum frequency is 7324Hz
[ 0.260000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.320000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.320000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.350000] msgmni has been set to 57
[ 0.350000] io scheduler noop registered
[ 0.370000] io scheduler deadline registered (default)
[ 0.380000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.400000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a 16550A
[ 0.420000] console [ttyS0] enabled
[ 0.420000] console [ttyS0] enabled
[ 0.420000] bootconsole [early0] disabled
[ 0.420000] bootconsole [early0] disabled
[ 0.450000] m25p80 spi32766.0: found gd25q32, expected w25q32
[ 0.470000] m25p80 spi32766.0: gd25q32 (4096 Kbytes)
[ 0.480000] 4 ofpart partitions found on MTD device spi32766.0
[ 0.490000] Creating 4 MTD partitions on "spi32766.0":
[ 0.500000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.510000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.530000] 0x000000040000-0x000000050000 : "factory"
[ 0.540000] 0x000000050000-0x000000400000 : "firmware"
[ 0.560000] 0x000000150595-0x000000400000 : "rootfs"
[ 0.560000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.600000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.600000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.620000] 0x000000360000-0x000000400000 : "rootfs_data"
[ 0.640000] eth0: done loading
[ 0.660000] rt3xxx-usbphy usbphy.3: loaded
[ 0.660000] rt2880_wdt 10000120.watchdog: Initialized
[ 0.680000] TCP: cubic registered
[ 0.680000] NET: Registered protocol family 17
[ 0.700000] 8021q: 802.1Q VLAN Support v1.8
[ 0.720000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.740000] Freeing unused kernel memory: 140K (802cd000 - 802f0000)
procd: Console is alive
procd: - watchdog -
[ 6.460000] usbcore: registered new interface driver usbfs
[ 6.480000] usbcore: registered new interface driver hub
[ 6.480000] usbcore: registered new device driver usb
[ 6.500000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.520000] ehci-platform: EHCI generic platform driver
[ 6.930000] rt3xxx-usbphy usbphy.3: remote usb device wakeup disabled
[ 6.950000] rt3xxx-usbphy usbphy.3: UTMI 16bit 30MHz
[ 6.950000] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 6.970000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 6.990000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 7.010000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 7.010000] hub 1-0:1.0: USB hub found
[ 7.030000] hub 1-0:1.0: 1 port detected
[ 7.040000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 7.060000] ohci-platform: OHCI generic platform driver
[ 7.060000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 7.080000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 7.100000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 7.160000] hub 2-0:1.0: USB hub found
[ 7.180000] hub 2-0:1.0: 1 port detected
procd: - preinit -
[ 7.970000] rt305x-esw 10110000.esw: link changed 0x00
[ 8.270000] random: mktemp urandom read with 71 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
jffs2 is ready
jffs2 is ready
[ 12.040000] jffs2: notice: (293) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 7 of xref (0 dead, 2 orphan) found.
switching to overlay
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 16.090000] NET: Registered protocol family 10
[ 16.100000] tun: Universal TUN/TAP device driver, 1.6
[ 16.120000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 16.140000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 16.160000] Loading modules backported from Linux version master-2014-09-26-0-g25e3efa
[ 16.180000] Backport generated by backports.git backports-20140905-1-gde42785
[ 16.200000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.240000] nf_conntrack version 0.5.0 (458 buckets, 1832 max)
[ 16.310000] xt_time: kernel timezone is -0000
[ 16.410000] cfg80211: Calling CRDA to update world regulatory domain
[ 16.440000] cfg80211: World regulatory domain updated:
[ 16.450000] cfg80211: DFS Master region: unset
[ 16.460000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 16.480000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 16.500000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 16.520000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 16.520000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 16.550000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 16.560000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 16.560000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 16.560000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 16.560000] PPP generic driver version 2.4.2
[ 16.560000] NET: Registered protocol family 24
[ 16.560000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected
[ 16.560000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected
[ 24.420000] random: nonblocking pool is initialized
procd: - init complete -
[ 27.520000] device eth0.1 entered promiscuous mode
[ 27.520000] device eth0 entered promiscuous mode
[ 27.540000] br-lan: port 1(eth0.1) entered forwarding state
[ 27.560000] br-lan: port 1(eth0.1) entered forwarding state
[ 29.570000] br-lan: port 1(eth0.1) entered forwarding state
[ 30.720000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 30.740000] device wlan0 entered promiscuous mode
[ 30.770000] br-lan: port 2(wlan0) entered forwarding state
[ 30.790000] br-lan: port 2(wlan0) entered forwarding state
[ 30.790000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 32.790000] br-lan: port 2(wlan0) entered forwarding stateSo far if no ethernet cable is connected on Wan and i activate wifi , well wifi is working. I can connect and get ip address.
If i disable WiFi and connect Wan ethernet cable (using DHCP) the router get an ip adress and i can connect on the "outside".
Now if Wan is connected and i activate wifi , Wan is not working anymore.
And i get the following log :
[ 3196.280000] rt305x-esw 10110000.esw: link changed 0x00
[ 3196.350000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3196.370000] device wlan0 entered promiscuous mode
[ 3196.410000] br-lan: port 2(wlan0) entered forwarding state
[ 3196.410000] br-lan: port 2(wlan0) entered forwarding state
[ 3196.430000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 3197.980000] rt305x-esw 10110000.esw: link changed 0x10
[ 3198.410000] br-lan: port 2(wlan0) entered forwarding state
[ 3199.740000] rt305x-esw 10110000.esw: link changed 0x10
[ 3201.490000] rt305x-esw 10110000.esw: link changed 0x10
[ 3203.410000] rt305x-esw 10110000.esw: link changed 0x10
[ 3205.080000] rt305x-esw 10110000.esw: link changed 0x10
[ 3206.740000] device wlan0 left promiscuous mode
[ 3206.740000] br-lan: port 2(wlan0) entered disabled state
[ 3206.800000] rt305x-esw 10110000.esw: link changed 0x10
[ 3207.440000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3207.440000] device wlan0 entered promiscuous mode
[ 3207.460000] br-lan: port 2(wlan0) entered forwarding state
[ 3207.470000] br-lan: port 2(wlan0) entered forwarding state
[ 3207.530000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 3208.600000] rt305x-esw 10110000.esw: link changed 0x10
[ 3209.470000] br-lan: port 2(wlan0) entered forwarding state
[ 3210.280000] rt305x-esw 10110000.esw: link changed 0x10
[ 3212.250000] rt305x-esw 10110000.esw: link changed 0x10
[ 3214.130000] rt305x-esw 10110000.esw: link changed 0x10
[ 3215.560000] rt305x-esw 10110000.esw: link changed 0x10
[ 3217.600000] rt305x-esw 10110000.esw: link changed 0x10
[ 3219.200000] rt305x-esw 10110000.esw: link changed 0x10
[ 3221.650000] rt305x-esw 10110000.esw: link changed 0x10
[ 3223.340000] rt305x-esw 10110000.esw: link changed 0x10
[ 3224.730000] rt305x-esw 10110000.esw: link changed 0x10
[ 3227.360000] rt305x-esw 10110000.esw: link changed 0x10
[ 3229.980000] rt305x-esw 10110000.esw: link changed 0x10
[ 3232.960000] rt305x-esw 10110000.esw: link changed 0x10
[ 3234.690000] rt305x-esw 10110000.esw: link changed 0x10
[ 3236.320000] rt305x-esw 10110000.esw: link changed 0x10
[ 3237.840000] rt305x-esw 10110000.esw: link changed 0x10
[ 3239.730000] rt305x-esw 10110000.esw: link changed 0x10
[ 3241.450000] rt305x-esw 10110000.esw: link changed 0x10
[ 3243.080000] rt305x-esw 10110000.esw: link changed 0x10
[ 3244.930000] rt305x-esw 10110000.esw: link changed 0x10
[ 3246.650000] rt305x-esw 10110000.esw: link changed 0x10
[ 3249.100000] rt305x-esw 10110000.esw: link changed 0x10
[ 3250.740000] rt305x-esw 10110000.esw: link changed 0x10The following line appears in loop in the TTY console.
[ 3250.740000] rt305x-esw 10110000.esw: link changed 0x10The only way out is disable wifi and reboot using the TTY console.
Also if wan is disconnected, and wifi is activated (which is working fine), when i plug ethernet cable on wan the loop starts again and wan is not accessible nor wifi.
So far i checked the source code for the ralink5350 but it doesn't seem the issue is coming from there.
Must be a setting somewhere i hope someone could help me out on this.
Thanks a lot !