my wr841n is bricked after installing openwrt.
i already connected serial console and tried gen-rick debricking.when i flash firmware after completion it shows Uncompressing Kernel Image ... Too big uncompressed streamLZMA ERROR 1
here is the console output
U-Boot 1.1.4 (Build from LSDK-9.5.3.16 at Nov 29 2013 - 10:46:36)
ap143 - Honey Bee 1.1
DRAM: 32 MB
Flash Manuf Id 0x1, DeviceId0 0x2, DeviceId1 0x15
Flash: 4 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
ath_gmac_enet_initialize: reset mask:0xc02200
Scorpion ---->S27 PHY*
S27 reg init
GMAC: cfg1 0x800c0000 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 4:0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4:0x10
eth0 up
Honey Bee ----> MAC 1 S27 PHY*
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
GMAC: cfg1 0x800c0000 cfg2 0x7214
eth1: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 0:0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0:0x10
athrs27_phy_setup ATHR_PHY_CONTROL 1:0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1:0x10
athrs27_phy_setup ATHR_PHY_CONTROL 2:0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2:0x10
athrs27_phy_setup ATHR_PHY_CONTROL 3:0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3:0x10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x60c1a100
is_auto_upload_firmware=0
Autobooting in 1 seconds
hb>
hb> setenv ipaddr 192.168.1.1
hb> setenv serverip 192.168.1.10
hb> printenv
bootargs=console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),2816k(rootfs),64k(config),64k(art)
bootcmd=bootm 0x9f020000
bootdelay=1
baudrate=115200
ethaddr=0xba:0xbe:0xfa:0xce:0x08:0x41
dir=
lu=tftp 0x80060000 ${dir}u-boot.bin&&erase 0x9f000000 +$filesize&&cp.b $fileaddr 0x9f000000 $filesize
lf=tftp 0x80060000 ${dir}ap143${bc}-squashfs&&erase 0x9f120000 +$filesize&&cp.b $fileaddr 0x9f120000 $filesize
lk=tftp 0x80060000 ${dir}vmlinux${bc}.lzma.uImage&&erase 0x9f020000 +$filesize&&cp.b $fileaddr 0x9f020000 $filesize
stdin=serial
stdout=serial
stderr=serial
ethact=eth0
ipaddr=192.168.1.1
serverip=192.168.1.10
Environment size: 676/65532 bytes
hb> tftpboot 0x80000000 a.bin
enet1 port3 up
dup 1 speed 1000
Using eth1 device
TFTP from server 192.168.1.10; our IP address is 192.168.1.1
Filename 'a.bin'.
Load address: 0x80000000
Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################
done
Bytes transferred = 3932160 (3c0000 hex)
hb> erase 0x9f020000 +0x3c0000
Erasing flash...
First 0x2 last 0x3d sector size 0x10000 61
Erased 60 sectors
hb> cp.b 0x81000000 0x9f020000 0x3c0000
Copy to Flash... write addr: 9f020000
done
hb> bootm 0x9f020000
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... Too big uncompressed streamLZMA ERROR 1 - must RESET board to recoverâ–’
U-Boot 1.1.4 (Build from LSDK-9.5.3.16 at Nov 29 2013 - 10:46:36)
ap143 - Honey Bee 1.1
DRAM: 32 MB
Flash Manuf Id 0x1, DeviceId0 0x2, DeviceId1 0x15
Flash: 4 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
ath_gmac_enet_initialize: reset mask:0xc02200
Scorpion ---->S27 PHY*
S27 reg init
GMAC: cfg1 0x800c0000 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 4:0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4:0x10
eth0 up
Honey Bee ----> MAC 1 S27 PHY*
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
GMAC: cfg1 0x800c0000 cfg2 0x7214
eth1: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 0:0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0:0x10
athrs27_phy_setup ATHR_PHY_CONTROL 1:0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1:0x10
athrs27_phy_setup ATHR_PHY_CONTROL 2:0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2:0x10
athrs27_phy_setup ATHR_PHY_CONTROL 3:0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3:0x10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x60c1a100
is_auto_upload_firmware=0
Autobooting in 1 seconds
