The output from the serial port if any one is interested.
Technicolor Gateway
(c) 2014, All rights reserved
Decompressing Bootloader................................
Gateway initialization sequence started
Boot Loader Version : 2.0.54
CPU : BCM63168-D0
RAM : 256MB
Flash : 128MB NAND, blocksize=128KB, pagesize=2048B
Board Mnemonic : VANT-F
Market ID : FFFCExternal switch id = 53125
Booting : Bank 1
Magic packet : [link up]
SW Version : 0.0.0.0.0
Starting the Linux kernel
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.4.11-rt19 (jenkins@edgmsjslv10) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 SMP PREEMPT Thu May 26 20:41:48 CEST 2016
[ 0.000000] VANT-F prom init
[ 0.000000] CPU revision is: 0002a080 (Broadcom BMIPS4350)
[ 0.000000] Reserving WL memory core 80b8e000-8108e000, init 8108e000-810ce000
[ 0.000000] Reserving DSL memory: 010CE000-011FFFFF
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 00b8c000 @ 00002000 (usable)
[ 0.000000] memory: 0eddf000 @ 01200000 (usable)
[ 0.000000] Wasting 64 bytes for tracking 2 unused pages
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000002 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x0000ffdf
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000002 -> 0x00000b8e
[ 0.000000] 0: 0x00001200 -> 0x0000ffdf
[ 0.000000] On node 0 totalpages: 63851
[ 0.000000] free_area_init_node: node 0, pgdat 804bed00, node_mem_map 81200040
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 2924 pages, LIFO batch:0
[ 0.000000] Normal zone: 480 pages used for memmap
[ 0.000000] Normal zone: 60415 pages, LIFO batch:15
[ 0.000000] PERCPU: Embedded 7 pages/cpu @81403000 s5536 r8192 d14944 u32768
[ 0.000000] pcpu-alloc: s5536 r8192 d14944 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 63339
[ 0.000000] Kernel command line: root=31:0 ro noinitrd memsize=0xFFDD000 btab=0xc004100c btab_bootid=1 tbbt_addr=0x7d20000 console=ttyS0,115200 root=/dev/mtdblock1 rootfstype=squashfs irqaffinity=0 console=ttyS0,115200 root=/dev/mtdblock1 rootfstype=squashfs irqaffinity=0
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] allocated 524008 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 247216k/255404k available (3855k kernel code, 8188k reserved, 942k data, 212k init, 0k highmem)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] console [ttyS0] enabled
[ 0.000000] Allocating memory for DSP module core and initialization code
[ 0.000000] Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0
[ 0.004000] Calibrating delay loop... 397.31 BogoMIPS (lpj=198656)
[ 0.016000] pid_max: default: 32768 minimum: 301
[ 0.017000] Mount-cache hash table entries: 512
[ 0.018000] --Kernel Config--
[ 0.019000] SMP=1
[ 0.020000] PREEMPT=1
[ 0.021000] DEBUG_SPINLOCK=0
[ 0.022000] DEBUG_MUTEXES=0
[ 0.023000] Initializing cgroup subsys debug
[ 0.024000] Initializing cgroup subsys memory
[ 0.025000] Initializing cgroup subsys blkio
[ 0.026000] Broadcom Logger v0.1 May 26 2016 20:30:2
[ 0.035000] CPU revision is: 0002a080 (Broadcom BMIPS4350)
[ 0.035000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
[ 0.035000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.045000] Brought up 2 CPUs
[ 0.053000] NET: Registered protocol family 16
[ 0.056000] Enabling watchdog
[ 0.168000] Internal 1P2 VREG will be shutdown if unused...Unused, turn it off (00009712-0000972f=-29<300)
[ 0.170000] registering PCI controller with io_map_base unset
[ 0.397000] registering PCI controller with io_map_base unset
[ 0.398000] gpiochip_add: registered GPIOs 0 to 51 on device: bcm963xx-gpio
[ 0.414000] bio: create slab <bio-0> at 0
[ 0.417000] SCSI subsystem initialized
[ 0.421000] usbcore: registered new interface driver usbfs
[ 0.422000] usbcore: registered new interface driver hub
[ 0.423000] usbcore: registered new device driver usb
[ 0.424000] PCI host bridge to bus 0000:00
[ 0.425000] pci_bus 0000:00: root bus resource [mem 0xa0f00000-0xa0ffffff]
[ 0.426000] pci_bus 0000:00: root bus resource [io 0xa2000000-0xa200ffff]
[ 0.427000] pci 0000:00:00.0: [14e4:435f] type 00 class 0x028000
[ 0.428000] pci 0000:00:00.0: reg 10: [mem 0x10004000-0x10005fff]
[ 0.429000] pci 0000:00:09.0: [14e4:6300] type 00 class 0x0c0310
[ 0.430000] pci 0000:00:09.0: reg 10: [mem 0x10002600-0x100026ff]
[ 0.431000] pci 0000:00:0a.0: [14e4:6300] type 00 class 0x0c0320
[ 0.432000] pci 0000:00:0a.0: reg 10: [mem 0x10002500-0x100025ff]
[ 0.434000] PCI host bridge to bus 0000:01
[ 0.435000] pci_bus 0000:01: root bus resource [mem 0x11000000-0x11efffff]
[ 0.436000] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
[ 0.437000] pci 0000:01:00.0: [14e4:6326] type 01 class 0x060400
[ 0.438000] pci 0000:01:00.0: PME# supported from D0 D3hot
[ 0.439000] pci 0000:02:00.0: [14e4:4360] type 00 class 0x028000
[ 0.440000] pci 0000:02:00.0: reg 10: [mem 0x00000000-0x00007fff 64bit]
[ 0.441000] pci 0000:02:00.0: supports D1 D2
[ 0.443000] pci 0000:01:00.0: BAR 8: assigned [mem 0x11000000-0x110fffff]
[ 0.444000] pci 0000:02:00.0: BAR 0: assigned [mem 0x11000000-0x11007fff 64bit]
[ 0.445000] pci 0000:01:00.0: PCI bridge to [bus 02-02]
[ 0.446000] pci 0000:01:00.0: bridge window [mem 0x11000000-0x110fffff]
[ 0.447000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[ 0.448000] bcmhs_spi bcmhs_spi.1: master is unqueued, this is deprecated
[ 0.449000] bcmleg_spi bcmleg_spi.0: master is unqueued, this is deprecated
[ 0.451000] skbFreeTask created successfully
[ 0.452000] gbpm_do_work scheduled
[ 0.453000] [0;34mBLOG v3.0 Initialized[0m
[ 0.454000] BLOG Rule v1.0 Initialized
[ 0.455000] Broadcom IQoS v0.1 May 26 2016 20:38:07 initialized
[ 0.456000] Broadcom GBPM v0.1 May 26 2016 20:38:07 initialized
[ 0.457000] NET: Registered protocol family 8
[ 0.458000] NET: Registered protocol family 20
[ 0.459000] Switching to clocksource MIPS
[ 0.464000] NET: Registered protocol family 2
[ 0.469000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.476000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.484000] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.490000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.496000] TCP: reno registered
[ 0.499000] UDP hash table entries: 128 (order: 0, 4096 bytes)
[ 0.506000] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
[ 0.512000] NET: Registered protocol family 1
[ 0.516000] PCI: CLS mismatch (64 != 16), using 16 bytes
[ 0.522000] bcm_tstamp initialized, (hpt_freq=200000000 2us_div=200 2ns_mult=5 2ns_shift=0)
[ 0.534000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.539000] jffs2: version 2.2 (NAND) (SUMMARY) (ZLIB) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc.
[ 0.551000] fuse init (API version 7.18)
[ 0.555000] msgmni has been set to 482
[ 0.561000] io scheduler noop registered (default)
[ 0.571000] Broadcom NAND controller (BrcmNand Controller)
[ 0.577000] mtd->oobsize=0, mtd->eccOobSize=0
[ 0.581000] NAND_CS_NAND_XOR=00000000
[ 0.584000] Disabling XOR: Before: SEL=40000001, XOR=00000000
[ 0.590000] Disabling XOR: After: SEL=40000000, XOR=00000000
[ 0.596000] B4: NandSelect=40000000, nandConfig=15142200, chipSelect=0
[ 0.603000] brcmnand_read_id: CS0: dev_id=01f1801d
[ 0.608000] After: NandSelect=40000000, nandConfig=15142200
[ 0.613000] Block size=00020000, erase shift=17
[ 0.618000] NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11
[ 0.626000] busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
[ 0.633000] timing1 not adjusted: 6574845b
[ 0.637000] timing2 not adjusted: 00001e96
[ 0.642000] BrcmNAND mfg 1 f1 SPANSION_S30ML01GP_08 128MB on CS0
[ 0.648000]
[ 0.648000] Found NAND on CS0: ACC=f7881010, cfg=15142200, flashId=01f1801d, tim1=6574845b, tim2=00001e96
[ 0.659000] BrcmNAND version = 0x0400 128MB @00000000
[ 0.664000] brcmnand_scan: B4 nand_select = 40000000
[ 0.670000] brcmnand_scan: After nand_select = 40000000
[ 0.675000] handle_acc_control: default CORR ERR threshold 6 bits
[ 0.681000] ACC: 16 OOB bytes per 512B ECC step; from ID probe: 16
[ 0.688000] page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
[ 0.695000] Brcm NAND controller version = 4.0 NAND flash size 128MB @18000000
[ 0.703000] ECC layout=brcmnand_oob_bch8_16_2k
[ 0.707000] brcmnand_scan: mtd->oobsize=64
[ 0.712000] brcmnand_scan: oobavail=11, eccsize=512, writesize=2048
[ 0.718000] brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=8, eccbytes=13
[ 0.729000] Gateway flash mapping
[ 0.732000] brcmnand_reset_corr_threshold: default CORR ERR threshold 6 bits for CS0
[ 0.743000] [NAND] : tBBT loaded
[ 0.743000]
[ 0.747000] Technicolor nand flash translation layer initialized.
[ 0.753000] flash mapping initialized, size=128 Mb
[ 0.759000] parse_btab: num_banks (5)
[ 0.763000] Creating 1 MTD partitions on "technicolor-nand-tl":
[ 0.768000] 0x000002200000-0x000004e60000 : "rootfs"
[ 0.776000] Creating 5 MTD partitions on "technicolor-nand-tl":
[ 0.781000] 0x000000080000-0x000002000000 : "rootfs_data"
[ 0.789000] 0x000002000000-0x000004e60000 : "bank_1"
[ 0.796000] 0x000004e60000-0x000007cc0000 : "bank_2"
[ 0.803000] 0x000000020000-0x000000040000 : "eripv2"
[ 0.810000] 0x000000040000-0x000000080000 : "rawstorage"
[ 0.817000] Creating 1 MTD partitions on "technicolor-nand-tl":
[ 0.822000] 0x00000001fffd-0x000000020000 : "blversion"
[ 0.834000] PPP generic driver version 2.4.2
[ 0.838000] PPP BSD Compression module registered
[ 0.842000] PPP Deflate Compression module registered
[ 0.848000] NET: Registered protocol family 24
[ 0.852000] brcmboard: brcm_board_init entry
[ 0.857000] DYING GASP IRQ initialized
0.860000] Serial: BCM63XX driver $Revision: 3.00 $
[ 0.866000] [0;33mMagic SysRq with Auxilliary trigger char enabled (type ^ h for list of supported commands)[0m
[ 0.876000] ttyS0 at MMIO 0xb0000180 (irq = 13) is a BCM63XX
[ 0.882000] ttyS1 at MMIO 0xb00001a0 (irq = 42) is a BCM63XX
[ 0.888000] Total # RxBds=1448
[ 0.891000] bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized
[ 0.891000]
[ 0.899000] bcmPktDma_init: Broadcom Packet DMA Library initialized
[ 0.905000] IPSEC SPU: SUCCEEDED
[ 0.909000] GACT probability NOT on
[ 0.912000] Mirror/redirect action on
[ 0.916000] u32 classifier
[ 0.919000] input device check on
[ 0.922000] Actions configured
[ 0.927000] TCP: cubic registered
[ 0.929000] Initializing XFRM netlink socket
[ 0.934000] NET: Registered protocol family 10
[ 0.941000] IPv6 over IPv4 tunneling driver
[ 0.948000] NET: Registered protocol family 17
[ 0.952000] NET: Registered protocol family 15
[ 0.957000] Bridge firewalling registered
[ 0.961000] Initializing MCPD Module
[ 0.964000] Ebtables v2.0 registered
[ 0.969000] ebt_time registered
[ 0.971000] ebt_ftos registered
[ 0.975000] ebt_wmm_mark registered
[ 0.978000] ebt_wmm_classmap registered
[ 0.982000] 8021q: 802.1Q VLAN Support v1.8
[ 0.998000] VFS: Mounted root (squashfs filesystem) readonly on device 31:1.
[ 1.006000] Freeing unused kernel memory: 212k freed
- preinit -
- regular preinit -
[ 4.809000] jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x010b2fe0: Read 0xffffffff, calculated 0x1ed61ec0
[ 5.665000] jffs2: notice: (351) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 35 of xref (0 dead, 0 orphan) found.
switching to jffs2
HOMEWARE_CONFIG_ON_ACTIVE_BANK
Dual bank, overlay on /overlay/bank_1
[ 7.702000] tommath: module license 'unspecified' taints kernel.
[ 7.707000] Disabling lock debugging due to kernel taint
[ 7.965000] eRIPv2 secrets passed correctly to Linux
[ 8.085000] Dsl Annex A board
[ 8.088000] Set board (VANT-F)
- init -
[ 11.133000] L2TP core: blog_l2tp_rcv_check
[ 11.136000] L2TP core driver, V2.0
[ 11.167000] L2TP netlink interface
[ 11.297000] gre: GRE over IPv4 demultiplexor driver
[ 11.330000] ip_gre: GRE over IPv4 tunneling driver
[ 11.365000] ip6_gre: GRE over IPv6 tunneling driver
[ 11.400000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.758000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 11.764000] PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
[ 11.770000] ehci_hcd 0000:00:0a.0: setting latency timer to 64
[ 11.776000] ehci_hcd 0000:00:0a.0: EHCI Host Controller
[ 11.781000] ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
[ 11.789000] ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
[ 11.815000] ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500
[ 11.826000] ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
[ 11.833000] hub 1-0:1.0: USB hub found
[ 11.836000] hub 1-0:1.0: 2 ports detected
[ 11.996000] nf_conntrack version 0.5.0 (3866 buckets, 15464 max)
[ 12.323000] PPPoL2TP kernel driver, V2.0
[ 13.155000] xt_time: kernel timezone is -0000
[ 14.356000] nf_conntrack_rtsp v0.7 loading
[ 14.388000] nf_nat_rtsp v0.7 loading
[ 14.584000] ncr_master_key_set_internal
[ 14.588000] ncr: driver 0.2-mr1 loaded.
[ 14.619000] Netfilter messages via NETLINK v0.30.
[ 15.299000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 15.783000] ctnetlink v0.93: registering with nfnetlink.
[ 15.961000] bcmxtmrt: Broadcom BCM3168D0 ATM/PTM Network Device v0.7 May 26 2016 18:27:22
[ 16.069000] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 16.075000] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 16.325000] OSCK LOADED!
[ 16.558000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 16.563000] PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
[ 16.569000] ohci_hcd 0000:00:09.0: setting latency timer to 64
[ 16.575000] ohci_hcd 0000:00:09.0: OHCI Host Controller
[ 16.581000] ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
[ 16.588000] ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600
[ 16.650000] hub 2-0:1.0: USB hub found
[ 16.654000] hub 2-0:1.0: 2 ports detected
[ 16.774000] Broadcom Ingress QoS Module Char Driver v0.1 May 26 2016 18:21:36 Registered<243>[0m
[ 16.783000]
[ 16.783000] Broadcom Ingress QoS ver 0.1 initialized
[ 16.817000] BPM: tot_mem_size=268435456B (256MB), buf_mem_size <15%> =40265310B (38MB), num of buffers=19972, buf size=2016
[ 16.828000] Broadcom BPM Module Char Driver v0.1 May 26 2016 18:20:30 Registered<244>[0m
[ 17.375000] NBUFF v1.0 Initialized
[ 17.405000] [0;36;44mInitialized fcache state[0m
[ 17.409000] [0;36;44mBroadcom Packet Flow Cache Char Driver v2.2 May 26 2016 18:21:37 Registered<242>[0m
[ 17.419000] Created Proc FS /procfs/fcache
[ 17.423000] [0;36;44mBroadcom Packet Flow Cache registered with netdev chain[0m
[ 17.431000] [0;36;44mBroadcom Packet Flow Cache learning via BLOG enabled.[0m
[ 17.438000] [0;35m[FHW] pktDbgLvl[0xc09bf210]=0[0m
[ 17.443000] [0;34m[FHW] fhw_construct: [0m
[ 17.449000] [0;36;44mInitialized Fcache HW accelerator layer state[0m
[ 17.457000] flwStatsThread created
[ 17.472000] [0;36;44mConstructed Broadcom Packet Flow Cache v2.2 May 26 2016 18:21:37[0m
[ 17.816000] chipId 0x631680D0
[ 17.818000] Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 May 26 2016 18:21:16 Registered <241>
[ 17.828000] Enabling SMISBUS PHYS_FAP_BASE[0] is 0x10c01000
[ 17.854000] FAP Soft Reset Done
[ 17.857000] 4ke Reset Done
[ 17.870000] Enabling SMISBUS PHYS_FAP_BASE[1] is 0x10c01000
[ 17.896000] FAP Soft Reset Done
[ 17.898000] 4ke Reset Done
[ 17.911000] FAP Debug values at 0xabba3fa0 0xab423fa0
[ 17.920000] fapGso_LoopBkThread created successfully
[ 17.924000] Allocated FAP0 SWQ_HOST2FAP_GSO_LOOPBACK_Q mem=af8e8000 : 16384 bytes
[ 17.932000] Allocated FAP0 SWQ_FAP2HOST_GSO_LOOPBACK_Q mem=afb24000 : 16384 bytes
[ 17.939000] GSO LOOPBACK Cached HOST2FAP Q INFO:
[ 17.939000] Swq =b0825ef0 qStart=af8e8000 qEnd=af8ec000 msgSize=4 dqm=18 fapId=0
[ 17.952000] GSO LOOPBACK Cached FAP2HOST Q INFO:
[ 17.952000] Swq =b0825ec0 qStart=afb24000 qEnd=afb28000 msgSize=2 dqm=19 fapId=0
[ 17.964000] Allocated FAP0 SWQ_FAP2HOST_WFD_Q mem=aecaa000 : 7200 bytes
[ 17.971000] Allocated FAP1 SWQ_FAP2HOST_WFD_Q mem=aecb0000 : 7200 bytes
[ 17.978000] Allocated FAP0 SWQ_FAP2HOST_WFD_Q mem=aecfe000 : 7200 bytes
[ 17.985000] Allocated FAP1 SWQ_FAP2HOST_WFD_Q mem=afb60000 : 7200 bytes
[ 17.992000] Allocated FAP0 TM SDRAM Queue Storage (abbb5030) : 390144 bytes @ ab480000
[ 18.000000] Allocated FAP1 TM SDRAM Queue Storage (ab435030) : 390144 bytes @ ab500000
[ 18.014000] [0;34m[NTC fapProto] fapReset : Reset FAP Protocol layer[0m
[ 18.017000] [FAP0] DSPRAM : stack <0x80000000><1792>, global <0x80000700><4576>, free <1824>, total<8192>
[ 18.017000] [FAP1] DSPRAM : stack <0x80000000><1792>, global <0x80000700><4576>, free <1824>, total<8192>
[ 18.017000] [FAP0] PSM : addr<0x80002000>, used <24464>, free <112>, total <24576>
[ 18.017000] [FAP1] PSM : addr<0x80002000>, used <24464>, free <112>, total <24576>
[ 18.017000] [FAP0] DQM : availableMemory 14668 bytes, nextByteAddress 0xE00048B0
[ 18.017000] [FAP1] DQM : availableMemory 14668 bytes, nextByteAddress 0xE00048B0
[ 18.020000] [FAP0] Initializing FAP4KE GSO LOOPBACK on fapIdx=0 ...
[ 18.020000] [FAP1] IC Timer started
[ 18.020000] [FAP0] SWQ: HOST2FAP_GSO_LOOPBACK
[ 18.020000] [FAP1] FAP4KE WFD Init Done...
[ 18.020000] [FAP0] >>>>------------------
[ 18.020000] [FAP0] swq =80007ef0 msgSize =4 words , maxDepth=1024
[ 18.020000] [FAP0] qStart =af8e8000 qEnd=af8ec000
[ 18.020000] [FAP0] rdPtr =af8e8000 wrPtr=af8e8000 count=0
[ 18.021000] [FAP0] swq->interrupts 0 processed =0 dropped =0
[ 18.021000] [FAP0] Associated DQM=18 dir HOST2FAP
[ 18.021000] [FAP0] ------------------<<<<
[ 18.021000] [FAP0] SWQ: FAP2HOST_GSO_LOOPBACK
[ 18.021000] [FAP0] >>>>------------------
[ 18.021000] [FAP0] swq =80007ec0 msgSize =2 words , maxDepth=2048
[ 18.021000] [FAP0] qStart =afb24000 qEnd=afb28000
[ 18.021000] [FAP0] rdPtr =afb24000 wrPtr=afb24000 count=0
[ 18.021000] [FAP0] swq->interrupts 0 processed =0 dropped =0
[ 18.021000] [FAP0] Associated DQM=19 dir FAP2HOST
[ 18.021000] [FAP0] ------------------<<<<
[ 18.021000] [FAP0] FAP4KE GSO LOOPBACK Init Done...
[ 18.021000] [FAP0] IC Timer started
[ 18.022000] [FAP0] FAP4KE WFD Init Done...
[ 18.023000] [FAP1] FAP BPM Initialized.
[ 18.024000] [FAP0] FAP BPM Initialized.
[ 18.188000] [0;36;44mBroadcom Packet Flow Cache HW acceleration enabled.[0m
[ 18.194000] fapDrv_construct: FAP0: pManagedMemory=b0820650. wastage 8 bytes
[ 18.201000] fapDrv_construct: FAP1: pManagedMemory=b0a20650. wastage 8 bytes
[ 18.209000] bcmPktDma_bind: FAP Driver binding successfull
[ 18.215000] [FAP1] FAP TM: ON
[ 18.217000] [FAP0] FAP TM: ON
[ 18.440000] Broadcom BCM63168D0 Ethernet Network Device v0.1 May 26 2016 18:26:56
[ 18.447000] Broadcom GMAC Char Driver v0.1 May 26 2016 18:27:18 Registered<249>[0m
[ 18.455000] Broadcom GMAC Driver v0.1 May 26 2016 18:27:18 Initialized
[ 18.461000] fapDrv_psmAlloc: fapIdx=1, size: 4800, offset=b0a20650 bytes remaining 7000
[ 18.470000] ETH Init: Ch:0 - 200 tx BDs at 0xb0a20650
[ 18.475000] fapDrv_psmAlloc: fapIdx=0, size: 4800, offset=b0820650 bytes remaining 7000
[ 18.483000] ETH Init: Ch:1 - 200 tx BDs at 0xb0820650
[ 18.488000] fapDrv_psmAlloc: wastage 8 bytes
[ 18.493000] fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b0821910 bytes remaining 2184
[ 18.501000] ETH Init: Ch:0 - 600 rx BDs at 0xb0821910
[ 18.506000] [FAP0] enetRxChannel 0
[ 18.513000] fapDrv_psmAlloc: wastage 8 bytes
[ 18.517000] fapDrv_psmAlloc: fapIdx=1, size: 4808, offset=b0a21910 bytes remaining 2184
[ 18.525000] ETH Init: Ch:1 - 600 rx BDs at 0xb0a21910
[ 18.530000] [FAP1] enetRxChannel 1
[ 18.548000] dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
[ 18.566000] eth0: <Ext sw port: 1> <Logical : 09> PHY_ID <0x20180001 : 0x01> MAC : E0:B9:E5:66:0D:96
[ 18.587000] eth1: <Ext sw port: 2> <Logical : 10> PHY_ID <0x20180002 : 0x02> MAC : E0:B9:E5:66:0D:96
[ 18.609000] eth2: <Ext sw port: 3> <Logical : 11> PHY_ID <0x20180003 : 0x03> MAC : E0:B9:E5:66:0D:96
[ 18.630000] eth3: <Ext sw port: 4> <Logical : 12> PHY_ID <0x20180004 : 0x04> MAC : E0:B9:E5:66:0D:96
[ 18.644000] ETH Init: Ch:1 - 200 tx BDs at 0xb0820650
[ 18.649000] ETH Init: Ch:1 - 600 rx BDs at 0xb0a21910
[ 18.656000] eth4: <Int sw port: 3> <Logical : 03> PHY_ID <0x0010004c : 0x0c> MAC : E0:B9:E5:66:0D:96
[ 18.656000] [FAP1] enetRxChannel 1
[ 18.825000] Ethernet Auto Power Down and Sleep: Enabled
[ 18.841000] Chip WAN Only Port 00000000, Defined WAN Only Port 00000000, WAN Only Port Result: 0x00000000
[ 18.850000] Chip WAN Preffered Port 00000008, Defined WAN Preffered Port 00000000, WAN Preffered Port Result: 0x00000008
[ 18.862000] Chip LAN Only Port 00000000, Defined LAN Only Port 00000000, LAN Only Port Result: 0x00000000
[ 18.909000] Broadcom 802.1Q VLAN Interface, v0.1
[ 19.042000] Load wl module core 80b8e000 (size 9021)
[ 19.047000] Load wl module init 8108e000 (size 2301)
[ 19.054000] [1m[34mWifi Forwarding Driver is initialized![0m
[ 19.087000] Load wl module core 80b91000 (size 35745)
[ 19.092000] Load wl module init 8108e000 (size 7379)
[ 21.513000] Load wl module core 80b9a000 (size 4245760)
[ 21.545000] Load wl module init 8108e000 (size 193513)
[ 21.627000] --SMP support
[ 21.629000] wl: dsl_tx_pkt_flush_len=338
[ 21.633000] wl: norm_wmark_tot=10043, pktc_wmark_tot=10043
[ 21.644000] wl 0000:00:00.0: setting latency timer to 64
[ 21.649000] wl: passivemode=1
[ 21.652000] wl0: creating kthread wl0-kthrd
[ 21.668000] wl: napimode=0
[ 21.674000] Neither SPROM nor OTP has valid image
[ 21.679000] wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
[ 21.692000] wl: ID=sb/0/
[ 21.694000] wl: ID=sb/0/
[ 21.741000] wl: loading /etc/wlan/bcm6362_map.bin
[ 21.745000] srom rev:8
[ 21.850000] wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=32
[ 21.888000] wl0: allocskbmode=1 currallocskbsz=1024
[ 21.901000] [1m[34m wfd_bind: Dev wl%d wfd_idx 0 Type skb configured WFD thread wfd0-thrd RxQId (20), status (0) number_of_queues 2 qmask 0x3[0m
[ 21.902000] Instantiating WFD 0 thread
[ 21.919000] +++++ Added gso loopback support for dev=wl0 <8b9f0800>
[ 21.926000] wl0: Broadcom BCM435f 802.11 Wireless Controller 7.14.89.14.cpe4.16L03.0-kdb
[ 21.934000] dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
[ 21.940000] PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
[ 21.946000] wl: passivemode=1
[ 21.949000] wl1: creating kthread wl1-kthrd
[ 21.964000] wl: napimode=0
[ 21.977000] initvars_cis_pci: Not CIS format
[ 21.992000] sprom_read_pci: buf[0] = 0xffff, returning bad-crc
[ 22.008000] sprom_read_pci: buf[0] = 0xffff, returning bad-crc
[ 22.016000] sprom_read_pci: buf[0] = 0xffff, returning bad-crc
[ 22.022000] wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
[ 22.030000] wl: ID=pci/2/0/
[ 22.033000] wl: ID=pci/2/0/
[ 22.113000] wl: loading /etc/wlan/bcm4360_map.bin
[ 22.118000] srom rev:11
[ 22.126000] wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=32
[ 22.191000] wl1: allocskbmode=1 currallocskbsz=3500
[ 22.223000] [1m[34m wfd_bind: Dev wl%d wfd_idx 1 Type skb configured WFD thread wfd1-thrd RxQId (21), status (0) number_of_queues 2 qmask 0xc[0m
[ 22.223000] Instantiating WFD 1 thread
[ 22.242000] +++++ Added gso loopback support for dev=wl1 <8b5ab800>
[ 22.248000] wl1: Broadcom BCM4360 802.11 Wireless Controller 7.14.89.14.cpe4.16L03.0-kdb
[ 22.256000] dgasp: kerSysRegisterDyingGaspHandler: wl1 registered
[ 22.422000] bcmxtmcfg: bcmxtmcfg_init entry
[ 22.676000] adsl: adsl_init entry
[ 22.853000] usbcore: registered new interface driver usbserial
[ 22.859000] usbserial: USB Serial Driver core
[ 22.998000] usbcore: registered new interface driver sierra
[ 23.004000] USB Serial support registered for Sierra USB modem
[ 23.037000] usbcore: registered new interface driver sierra_net
[ 23.081000] Initializing USB Mass Storage driver...
[ 23.086000] usbcore: registered new interface driver usb-storage
[ 23.091000] USB Mass Storage support registered.
[ 23.124000] usbcore: registered new interface driver cdc_wdm
[ 23.403000] usbcore: registered new interface driver cdc_ether
[ 23.657000] [0;34m[NTC arl] arlEnable : Enabled ARL binding to FAP[0m
[ 23.664000] Broadcom Address Resolution Logic Processor (ARL) Char Driver v0.1 May 26 2016 18:20:29 Registered <245>
[ 23.806000] input: gpio-buttons as /devices/platform/gpio-buttons.0/input/input0
[ 23.952000] Button Hotplug driver version 0.4.1
[ 23.987000] usbcore: registered new interface driver cdc_ncm
[ 24.019000] usbcore: registered new interface driver huawei_cdc_ncm
[ 24.161000] usbcore: registered new interface driver qmi_wwan
[ 24.271000] usbcore: registered new interface driver option
[ 24.276000] USB Serial support registered for GSM modem (1-port)
[ 24.311000] usbcore: registered new interface driver qcserial
[ 24.316000] USB Serial support registered for Qualcomm USB modem
[ 24.699000] Loading DECT Shim driver
[ 24.702000] Initialize DECT Shim layer....
[ 24.707000] Obtained board id string (VANT-F)
[ 24.711000] Obtained Base board id string (VANT-F)Successfully obtained voice parameters
[ 24.721000] DECT shim power up is done
[ 24.724000] configure dect PLL
[ 24.737000] ####################SUCCESS: DECT PLL IS LOCKED#################
[ 24.744000] dect shm irq status: 0x00000080, i: 1
[ 24.749000] DECT PLL init completed successfully
[ 24.754000] DECT DMA DDR Rx Physical Address : 0x00805000
[ 24.759000] DECT DMA DDR Rx Virtual Address : 0xA0805000
[ 24.765000] DECT DMA DDR Rx Virtual Addressptr: 0xC1266C44
[ 24.771000] DECT DMA DDR Tx Physical Address : 0x0080C000
[ 24.777000] DECT DMA DDR Tx Virtual Address : 0xA080C000
[ 24.782000] DECT DMA DDR Tx Virtual Addressptr: 0xC1266C48
[ 24.788000] DECT_CTRL->dect_shm_pll_reg_0 : 0x210064C0
[ 24.794000] DECT_CTRL->dect_shm_pll_reg_1 : 0x00501015
[ 24.799000] DECT_CTRL->dect_shm_pll_reg_2 : 0x60000000
[ 24.804000] DECT_CTRL->dect_shm_pll_reg_3 : 0x11181808
[ 24.810000] dect_shm_dma_ddr_saddr_tx_s0 : 0x0080c000
[ 24.815000] dect_shm_dma_ddr_saddr_tx_s1 : 0x0080c140
[ 24.821000] dect_shm_dma_ddr_saddr_tx_s2 : 0x0080c280
[ 24.826000] dect_shm_dma_ddr_saddr_tx_s3 : 0x0080c3c0
[ 24.832000] dect_shm_dma_ddr_saddr_rx_s0 : 0x00805000
[ 24.837000] dect_shm_dma_ddr_saddr_rx_s1 : 0x00805140
[ 24.843000] dect_shm_dma_ddr_saddr_rx_s2 : 0x00805280
[ 24.848000] dect_shm_dma_ddr_saddr_rx_s3 : 0x008053c0
[ 24.854000] dect_shm_dma_ahb_saddr_tx_s01 : 0x0a200de0
[ 24.859000] dect_shm_dma_ahb_saddr_tx_s23 : 0x11a01560
[ 24.865000] dect_shm_dma_ahb_saddr_rx_s01 : 0x08400c00
[ 24.870000] dect_shm_dma_ahb_saddr_rx_s23 : 0x0fc01380
[ 24.876000] dect_shm_dma_offset_addr_tx_s01 : 0x00000000
[ 24.881000] dect_shm_dma_offset_addr_rx_s01 : 0x00000000
[ 24.886000] dect_shm_dma_xfer_size_tx : 0x28282828
[ 24.892000] dect_shm_dma_xfer_size_rx : 0x28282828
[ 24.897000] dect_shm_dma_buf_size_tx : 0x02020202
[ 24.903000] dect_shm_dma_buf_size_rx : 0x02020202
[ 24.908000] dect_shm_dma_xfer_cntr_tx : 0x00000000
[ 24.914000] dect_shm_dma_xfer_cntr_rx : 0x00000000
[ 24.919000] dect_shm_dma_ctrl : 0x030088ff
[ 25.024000] Loading PCM shim driver
[ 25.454000] ufsd: trace mask set to 0000000f
[ 25.458000] ufsd: driver (8.6, May 26 2016 20:14:13, LBD=ON, delalloc, ioctl, rwm, tr) loaded at c1318000
[ 25.458000] NTFS support included
[ 25.458000] Hfs+/HfsX support included
[ 25.458000] Big endian platform
[ 25.458000] optimized: size
[ 26.138000] dect: Loading BCM6362 DECT Stack
[ 26.142000] dect: Version: , Build date: 2016/05/26, 20:05
[ 39.203000] Registered led device: power:green
[ 39.207000] Registered led device: power:red
[ 39.211000] Registered led device: power:blue
[ 39.216000] Registered led device: wireless:green
[ 39.220000] Registered led device: wireless_5g:green
[ 39.226000] Registered led device: broadband:green
[ 39.230000] Registered led device: internet:red
[ 39.235000] Registered led device: internet:green
[ 39.240000] Registered led device: wps:red
[ 39.244000] Registered led device: wps:green
[ 39.249000] Registered led device: ethernet:green
[ 39.254000] Registered led device: dect:green
[ 39.258000] Registered led device: dect:red
[ 39.262000] Registered led device: iptv:green
[ 39.267000] Registered led device: voip:green
[ 39.272000] Registered led device: power:orange
[ 39.276000] Registered led device: wps:orange
[ 39.280000] Registered led device: internet:orange
[ 39.285000] Registered led device: dect:orange
Note: Loading 6300 MDK (default) driver for 63168 chip
Note: Forcing 53115 driver for 53125
Switch MDK: num_switches = 2
Switch MDK: unit = 0; phy_pbmp = 0x8; config_pbmp = 0x18
Switch MDK: unit = 1; phy_pbmp = 0x1e; config_pbmp = 0x1e
Switch MDK link poll thread: unit=0; phypbmp=0x8 config_pbmp=0x18
Switch MDK link poll thread: unit=1; phypbmp=0x1e config_pbmp=0x1e
[ 41.786000] Energy Efficient Ethernet: Enabled
[ 48.268000] monitor task is initialized pid= 1699
[ 48.421000] bcmxtmcfg: DS xDSL G.inp Mode = DISABLED
[ 48.426000] bcmxtmcfg: xDSL G.Fast Mode = DISABLED
[ 48.431000] fapDrv_psmAlloc: fapIdx=1, size: 1600, offset=b0a22be0 bytes remaining 584
[ 48.439000] XTM Init: Ch:0 - 200 rx BDs at 0xb0a22be0
[ 48.444000] fapDrv_psmAlloc: fapIdx=1, size: 128, offset=b0a23220 bytes remaining 456
[ 48.452000] XTM Init: Ch:1 - 16 rx BDs at 0xb0a23220
[ 48.459000] bcmxtmrt: PTM/ATM Non-Bonding Mode configured in system
[ 48.465000] bcmxtmcfg: Out of sequence call to XTM_ASM_HANDLER::Uninitialize(). Recovering.
[ 48.474000] bcmxtmcfg: ATM Bonding configured in system. Fallback mode = Enabled
[ 48.482000] bcmxtmcfg: Bonding State is DATA_IDLE
[ 48.486000] bcmxtmcfg: SID MODE SET to 12 BIT MODE
[ 48.491000] bcmxtmcfg: ATM Bonding Mgmt Log Area = 88d18514
[ 48.497000] bcmxtmcfg: gulXtmMonitorValid(0xc10addb4) = 1
[ 49.149000] bcmxtmrt: TxPAF Status = Disabled
[ 49.153000] bcmxtmrt: MAC address: e0 b9 e5 66 0d 96
[ 49.159000] [DoCreateDeviceReq.781]: register_netdev
[ 49.171000] [DoCreateDeviceReq.786]: register_netdev done
[ 49.176000] [FAP0] xtmCreateDevice : devId 0, encapType 0, headerLen 0
[ 49.183000] [FAP1] xtmCreateDevice : devId 0, encapType 0, headerLen 0
[ 49.218000] ADDRCONF(NETDEV_UP): ptm0: link is not ready
[ 49.776000] bcmxtmrt: TxPAF Status = Disabled
[ 49.780000] bcmxtmrt: MAC address: e0 b9 e5 66 0d 96
[ 49.786000] [DoCreateDeviceReq.781]: register_netdev
[ 49.796000] [DoCreateDeviceReq.786]: register_netdev done
[ 49.801000] [FAP0] xtmCreateDevice : devId 1, encapType 0, headerLen 0
[ 49.807000] [FAP1] xtmCreateDevice : devId 1, encapType 0, headerLen 0
[ 49.834000] ADDRCONF(NETDEV_UP): atm_8_35: link is not ready
[ 50.307000] NComm TMS V6.80 Kernel Module loaded.
[ 50.614000] NComm Ethernet 802.1AG OA&M loaded.
[ 50.638000] NComm Ethernet 802.3AH OA&M loaded.
[ 54.621000] wl_event_open
[ 54.623000] wl_event_open COMPLETED
Hostapd starting... (1)
[ 56.203000] wl1: wlc_dfs_cacstate_init: state to PRE-ISM Channel Availability Check channel 100
Hostapd starting... (2)
Hostapd starting... (3)
[ 58.127000] *** dslThread dslPid=1950
[ 58.130000] BcmAdsl_Initialize=0xC1116050, g_pFnNotifyCallback=0xC1151580
[ 58.417000] lmemhdr[2]=0x100CE000, pAdslLMem[2]=0x100CE000
[ 58.422000] pSdramPHY=0xA11FFFF8, 0xB5B56311 0xBF73E957
[ 58.427000] *** XfaceOffset: 0x5FF90 => 0x5FF90 ***
[ 59.049000] *** PhySdramSize got adjusted: 0xF440C => 0x128840 ***
[ 59.055000] AdslCoreSharedMemInit: shareMemSize=38816(38816)
[ 59.072000] AdslCoreHwReset: pLocSbSta=88eb0000 bkupThreshold=3072
[ 59.078000] AdslCoreHwReset: AdslOemDataAddr = 0xA11B2EC0
[ 59.084000] VersionInfo: A2pv6F039t.d26g
[ 59.088000] ***BcmDiagsMgrRegisterClient: 0 ***
[ 59.092000] dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
[ 64.127000] Line 0: xDSL G.994 training
[ 64.319000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 64.333000] device eth0 entered promiscuous mode
[ 64.387000] ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 64.412000] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 64.419000] device eth1 entered promiscuous mode
[ 64.442000] ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 64.449000] device eth2 entered promiscuous mode
[ 64.473000] ADDRCONF(NETDEV_UP): eth3: link is not ready
[ 64.479000] device eth3 entered promiscuous mode
[ 66.544000] device wl0 entered promiscuous mode
[ 66.548000] br-lan: port 5(wl0) entered forwarding state
[ 66.553000] br-lan: port 5(wl0) entered forwarding state
[ 66.561000] ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 66.663000] device wl1 entered promiscuous mode
[ 66.680000] br-lan: port 6(wl1) entered forwarding state
[ 66.685000] br-lan: port 6(wl1) entered forwarding state
[ 68.560000] br-lan: port 5(wl0) entered forwarding state
[ 68.688000] br-lan: port 6(wl1) entered forwarding state
[ 75.132000] Line 0: xDSL link down
[ 77.135000] Line 0: xDSL G.994 training
[ 90.138000] Line 0: VDSL G.993 started
[ 96.997000] eth0 (Ext switch port: 1) (Logical Port: 9) Link UP 1000 mbps full duplex
[ 97.035000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 97.041000] br-lan: port 1(eth0) entered forwarding state
[ 97.046000] br-lan: port 1(eth0) entered forwarding state
[ 99.048000] br-lan: port 1(eth0) entered forwarding state
[ 108.941000] br_netlink_mcpd.c: Setting registration type 0 pid to 3863
[ 125.635000] dect: unloading...
[ 125.638000] dect: exited
[ 139.283000] Endpoint: endpoint_init entry
[ 139.288000] Endpoint: endpoint_init COMPLETED
[ 139.579000] mmConnKrnlBrcm: INIT: num_rtpsock_ctx = 42
[ 139.584000] mmConnKrnlBrcm: INIT: COMPLETED
[ 144.897000] BOS: Enter bosInit
[ 144.900000] BOS: Exit bosInit
[ 145.093000] ******* DSP: Found BCM63268 *******
[ 145.097000] ******* DSP: In PCM Mode *******
[ 145.102000] ******* DSP: PCM running in 16 bit mode *******
[ 145.107000] gInterruptCounter = 0xC31590B4
[ 145.111000] gInterruptErrors = 0xC31590B0
[ 145.116000] gNextRxDesc = 0xC31591E8
[ 145.121000] gNextTxDesc = 0xC31591EC
[ 145.126000] gDectTestMode = 0xc31591fc
[ 145.131000] dectBuffStart = 0xc31591f0
[ 145.136000] gDectRxOutOfSyncCounter = 0xc3159210
[ 145.141000] gDectTxOutOfSyncCounter = 0xc3159214
[ 145.146000] 32 ms ECAN tail-length
[ 145.149000] *** gStartRxDesc[0] = 0xA7D6E000
[ 145.154000] *** gBufferSizeBytes = 640
[ 145.158000] *** gStartTxDesc[0] = 0xA7D6E7D0
[ 145.162000] halPcmInit 367 nextTxDesc = 0xA7D6E7D0
[ 145.168000] halPcmInit 367 nextTxDesc = 0xA7D6E7D8
[ 145.172000] halPcmInit 371 Ownership for TX desc not set. Use this buffer.
[ 145.180000] Binding 0x8fb2aa18
[ 145.187000] [0;35m[DBG xdrv_slic] slicSi32261Init: (ts: 25s 186ms):SLIC: Starting 32261 device and line initializion...[0m
[ 145.709000] [0;35m[DBG xdrv_slic] deviceSiLabsReset: (ts: 25s 708ms):SLIC: Reset applied on GPIO pin 15[0m
[ 145.723000] [0;35m[DBG xdrv_slic] initSiLabsDevice: (ts: 25s 722ms):SLIC: Initializing SiLabs device 0[0m
[ 147.026000] [0;35m[DBG xdrv_slic] initSiLabsDevice: (ts: 27s 25 ms):SLIC: SiLabs device BOM Type: 6[0m
[ 147.041000] [0;35m[DBG xdrv_slic] initSiLabsDevice: (ts: 27s 40 ms):SLIC: SiLabs device 0 initialized OK[0m
[ 147.055000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 27s 54 ms):SLIC: SiLabs Locale set to 0[0m
[ 147.071000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 27s 70 ms):SLIC: Initializing SiLabs FXS line 0[0m
[ 147.122000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 27s 121ms):FXS channel 0 Rx Gain: -9[0m
[ 147.132000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 27s 131ms):FXS channel 0 Tx Gain: -4[0m
[ 147.186000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 27s 185ms):SLIC: FXS line 0 RX timeslot = 0 [0m
[ 147.199000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 27s 198ms):SLIC: FXS line 0 TX timeslot = 0 [0m
[ 147.209000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 27s 208ms):SLIC: SiLabs FXS line 0 initialized OK[0m
[ 147.224000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 27s 223ms):SLIC: Initializing SiLabs FXS line 1[0m
[ 147.284000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 27s 283ms):FXS channel 1 Rx Gain: -9[0m
[ 147.296000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 27s 295ms):FXS channel 1 Tx Gain: -4[0m
[ 147.322000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 27s 321ms):SLIC: FXS line 1 RX timeslot = 1 [0m
[ 147.331000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 27s 330ms):SLIC: FXS line 1 TX timeslot = 1 [0m
[ 147.342000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 27s 341ms):SLIC: SiLabs FXS line 1 initialized OK[0m
[ 147.353000] [0;35m[DBG xdrv_slic] slicSi32261Init: (ts: 27s 352ms):SLIC: 32261 device 0 and FXS initializion COMPLETED OK ![0m
[ 147.901000] [0;35m[DBG xdrv_slic] OpenDaa : (ts: 27s 900ms): DAA DBG: Successful READ!!!! count = 0 [0m
[ 147.921000] [0;35m[DBG xdrv_slic] StartDaa : (ts: 27s 920ms): DAA DBG: ISOCAP lock count = 0 [0m
[ 147.934000] [0;35m[DBG xdrv_slic] StartDaa : (ts: 27s 933ms):Si3050 SLAC Initialised, Line side device = Si: 3019 (0x3)[0m
[ 147.945000] [0;35m[DBG xdrv_slic] StartDaa : (ts: 27s 944ms):System dev rev: 0x5, Line dev rev: 0x6[0m
[ 147.955000] [0;35m[DBG xdrv_slic] StartDaa : (ts: 27s 954ms):Line dev status: FDT:0x1, LCS: 0x0[0m
[ 147.965000] [0;35m[DBG xdrv_slic] StartDaa : (ts: 27s 965ms):DAA initialized with country code 0[0m
[ 147.975000] [0;35m[DBG xdrv_slic] daaSi3050Init: (ts: 27s 974ms):DAA Device Init completed. [0m
[ 147.985000] boardHalInit completed
[ 148.002000] DSP: Interrupt Ids
[ 148.004000] ---------------
[ 148.008000] InterruptId/Location = 42/HIGH
[ 148.013000]
[ 148.013000] DSP: Interrupt Masks
[ 148.017000] ---------------
[ 148.021000] IrqMask = 0x00000100
[ 148.026000] IrqMaskLow = 0x838066A0
[ 148.031000] IrqMask1 = 0x00000000
[ 148.036000] IrqMaskLow1 = 0x00000000
[ 148.041000]
[ 148.041000] DSP: Interrupt Status
[ 148.045000] -----------------
[ 148.049000] IrqStatus = 0x00100000
[ 148.054000] IrqStatusLow = 0x00038100
[ 148.059000] IrqStatus1 = 0x00100000
[ 148.064000] IrqStatusLow1 = 0x08038100
[ 148.551000] EndpointInit completed
[ 148.554000] dgasp: kerSysRegisterDyingGaspHandler: endpoint registered
[ 148.739000] dectshim open device...
[ 148.743000] dectshim open device...
[ 148.747000] kernel::dectshim_ioctl: command 0
[ 148.753000] Kick dma Tx once
[ 148.755000] Kick dma Rx once
[ 148.759000] dectshim close device...
[ 149.072000] [0;35m[DBG xdrv_slic] daaSi3050ModeControl: (ts: 29s 71 ms):DAA: Enable on-hook Caller ID receive. [0m
[ 149.141000] [0;33;41m[ERROR ept] ProvisionRingParams,3163: (ts: 29s 140ms):Ring offset of 25 not supported. Using default of 25 V for endpt 5[0m
[ 149.196000] [0;33;41m[ERROR ept] ProvisionRingParams,3163: (ts: 29s 196ms):Ring offset of 25 not supported. Using default of 25 V for endpt 4[0m
[ 157.553000] dect: Loading BCM6362 DECT Stack
[ 157.557000] dect: Version: , Build date: 2016/05/26, 20:05
[ 157.597000] ### RsHookReady 20160526 20:05
[ 157.600000] DECT DIP IRQ handler installed!
**** DectTestModePreInit:bTmp=0x00
ApiFpPcmTaskInit
[ 157.620000] ### RsHookRunning 2.
**** DectTestModeRunning:
dectshim open device...
[ 161.806000] kernel::dectshim_ioctl: command 5
[ 161.810000] dectshimGetVirtualAddr called
[ 161.815000] dectshim close device...
[ 161.826000] DECT Driver: Obtained Voice board id string (VANT-F)
[ 161.832000] DECT Driver: Obtained Base board id string (VANT-F)
[ 161.838000] DECT Driver: Successfully obtained voice parameters
[ 161.844000] DECT Driver: DECT RF Reset GPIO_8_AL
[ 161.852000] dect: Detected RF Frontend: LMX4181 rev A0
[ 187.151000] Line 0: VDSL G.993 channel analysis
[ 187.637000] Line 0: VDSL2 link up, Bearer 0, us=6400, ds=28000
[ 187.642000] Line 0: VDSL2 link up, Bearer 1, us=0, ds=0
[ 187.647000] bcmxtmcfg: DS xDSL G.inp Mode = ENABLED
[ 187.653000] bcmxtmcfg: xDSL G.Fast Mode = DISABLED
[ 187.658000] bcmxtmcfg: XTM Link Information, port = 0, State = UP(1), Service Support = PTM(2)
[ 187.667000] bcmxtmcfg: ReconfigureSAR port 0 traffictype 2
[ 187.672000] bcmxtmcfg: Normal(XTM/PTM) Mode enabled
[ 187.677000] bcmxtmcfg: Reserve TxQueueIdx=0 for vcid 0
[ 187.683000] bcmxtmcfg: Reserve TxQueueIdx=1 for vcid 0
[ 187.688000] bcmxtmcfg: Reserve TxQueueIdx=2 for vcid 0
[ 187.693000] bcmxtmcfg: Reserve TxQueueIdx=3 for vcid 0
[ 187.699000] bcmxtmcfg: Reserve TxQueueIdx=4 for vcid 0
[ 187.704000] bcmxtmcfg: Reserve TxQueueIdx=5 for vcid 0
[ 187.709000] bcmxtmcfg: Reserve TxQueueIdx=6 for vcid 0
[ 187.714000] bcmxtmcfg: Reserve TxQueueIdx=7 for vcid 0
[ 187.720000] XTM Init: Ch:0 - 400 tx BDs at 0xa7edc000
[ 187.728000] XTM Init: Ch:1 - 400 tx BDs at 0xa7d44000
[ 187.735000] XTM Init: Ch:2 - 400 tx BDs at 0xa5f04000
[ 187.742000] XTM Init: Ch:3 - 400 tx BDs at 0xa7d80000
[ 187.749000] XTM Init: Ch:4 - 400 tx BDs at 0xa5f00000
[ 187.756000] XTM Init: Ch:5 - 400 tx BDs at 0xa7cac000
[ 187.764000] XTM Init: Ch:6 - 400 tx BDs at 0xa7ecc000
[ 187.771000] XTM Init: Ch:7 - 400 tx BDs at 0xa7ec0000
[ 187.779000] bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=6400000, DS=28000000
[ 187.787000] [FAP0] xtmLinkUp : devId 0, matchId 0
[ 187.791000] [FAP1] xtmLinkUp : devId 0, matchId 0
[ 193.030000] br-lan: port 6(wl1) entered disabled state
[ 193.035000] br-lan: port 5(wl0) entered disabled state
[ 193.040000] br-lan: port 1(eth0) entered disabled state
[ 193.125000] device eth0 left promiscuous mode
[ 193.129000] br-lan: port 1(eth0) entered disabled state
[ 193.152000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 193.162000] device eth1 left promiscuous mode
[ 193.167000] br-lan: port 2(eth1) entered disabled state
[ 193.197000] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 193.214000] device eth2 left promiscuous mode
[ 193.223000] br-lan: port 3(eth2) entered disabled state
[ 193.254000] ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 193.272000] device eth3 left promiscuous mode
[ 193.277000] br-lan: port 4(eth3) entered disabled state
[ 193.314000] ADDRCONF(NETDEV_UP): eth3: link is not ready
[ 193.325000] device wl0 left promiscuous mode
[ 193.333000] br-lan: port 5(wl0) entered disabled state
[ 193.350000] device wl1 left promiscuous mode
[ 193.353000] br-lan: port 6(wl1) entered disabld state
[ 193.475000] device eth0 entered promiscuous mode
[ 193.546000] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 193.553000] device eth1 entered promiscuous mode
[ 193.571000] ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 193.584000] device eth2 entered promiscuous mode
[ 193.610000] ADDRCONF(NETDEV_UP): eth3: link is not ready
[ 193.620000] device eth3 entered promiscuous mode
[ 193.628000] device wl0 entered promiscuous mode
[ 193.638000] device wl1 entered promiscuous mode
[ 193.657000] br-lan: port 6(wl1) entered forwarding state
[ 193.662000] br-lan: port 6(wl1) entered forwarding state
[ 193.667000] br-lan: port 5(wl0) entered forwarding state
[ 193.673000] br-lan: port 5(wl0) entered forwarding state
[ 193.678000] br-lan: port 1(eth0) entered forwarding state
[ 193.684000] br-lan: port 1(eth0) entered forwarding state
[ 194.934000] NComm Ethernet 802.1AG OA&M unloaded.
[ 195.294000] NComm Ethernet 802.3AH OA&M unloaded.
[ 195.664000] br-lan: port 6(wl1) entered forwarding state
[ 195.680000] br-lan: port 5(wl0) entered forwarding state
[ 195.688000] br-lan: port 1(eth0) entered forwarding state
[ 195.780000] NComm Ethernet 802.1AG OA&M loaded.
[ 196.112000] NComm Ethernet 802.3AH OA&M loaded.
[ 197.129000] NComm Ethernet 802.1AG OA&M unloaded.
[ 197.419000] NComm Ethernet 802.3AH OA&M unloaded.
[ 198.106000] HOST XTM tx ch 0 disabled.
[ 198.169000] HOST XTM tx ch 1 disabled.
[ 198.258000] HOST XTM tx ch 2 disabled.
[ 198.356000] HOST XTM tx ch 3 disabled.
[ 198.426000] HOST XTM tx ch 4 disabled.
[ 198.488000] HOST XTM tx ch 5 disabled.
[ 198.568000] HOST XTM tx ch 6 disabled.
[ 198.643000] HOST XTM tx ch 7 disabled.
[ 198.718000] bcmxtmcfg: Connection DOWN, LinkActiveStatus=0x0
[ 201.693000] bcmxtmrt: TxPAF Status = Disabled
[ 201.697000] bcmxtmrt: MAC address: e0 b9 e5 66 0d 96
[ 201.703000] [DoCreateDeviceReq.781]: register_netdev
[ 201.718000] [DoCreateDeviceReq.786]: register_netdev done
[ 201.742000] [FAP0] xtmCreateDevice : devId 0, encapType 0, headerLen 0
[ 201.748000] [FAP1] xtmCreateDevice : devId 0, encapType 0, headerLen 0
[ 201.779000] bcmxtmcfg: Reserve TxQueueIdx=0 for vcid 0
[ 201.784000] bcmxtmcfg: Reserve TxQueueIdx=1 for vcid 0
[ 201.789000] bcmxtmcfg: Reserve TxQueueIdx=2 for vcid 0
[ 201.794000] bcmxtmcfg: Reserve TxQueueIdx=3 for vcid 0
[ 201.800000] bcmxtmcfg: Reserve TxQueueIdx=4 for vcid 0
[ 201.805000] bcmxtmcfg: Reserve TxQueueIdx=5 for vcid 0
[ 201.810000] bcmxtmcfg: Reserve TxQueueIdx=6 for vcid 0
[ 201.816000] bcmxtmcfg: Reserve TxQueueIdx=7 for vcid 0
[ 201.852000] [FAP0] xtmLinkUp : devId 0, matchId 0
[ 201.857000] [FAP1] xtmLinkUp : devId 0, matchId 0
[ 201.880000] XTM Init: Ch:0 - 400 tx BDs at 0xa8df4000
[ 201.894000] XTM Init: Ch:1 - 400 tx BDs at 0xa7ec0000
[ 201.907000] XTM Init: Ch:2 - 400 tx BDs at 0xa5efc000
[ 201.924000] XTM Init: Ch:3 - 400 tx BDs at 0xa7e8c000
[ 201.944000] XTM Init: Ch:4 - 400 tx BDs at 0xa5f48000
[ 201.959000] XTM Init: Ch:5 - 400 tx BDs at 0xa8df0000
[ 201.977000] XTM Init: Ch:6 - 400 tx BDs at 0xa5f1c000
[ 201.993000] XTM Init: Ch:7 - 400 tx BDs at 0xa7ea8000
[ 202.006000] bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=6400000, DS=28000000
[ 204.665000] dev = ptm0(0x88DE1800) macAddr=E0:B9:E5:66:D:96
[ 204.670000] Line0: VCE macAddr=0:19:8F:1C:EF:42, VTU-R macAddr=E0:B9:E5:66:D:96
[ 204.739000] bcmxtmrt: TxPAF Status = Disabled
[ 204.755000] bcmxtmrt: MAC address: e0 b9 e5 66 0d 96
[ 204.759000] [DoCreateDeviceReq.781]: register_netdev
[ 204.781000] [DoCreateDeviceReq.786]: register_netdev done
[ 204.802000] [FAP0] xtmCreateDevice : devId 1, encapType 0, headerLen 0
[ 204.808000] [FAP1] xtmCreateDevice : devId 1, encapType 0, headerLen 0
[ 204.912000] ADDRCONF(NETDEV_UP): atm_8_35: link is not ready
[ 205.891000] NComm Ethernet 802.1AG OA&M loaded.
[ 206.359000] NComm Ethernet 802.3AH OA&M loaded.
[ 272.096000] DoVrgEndptDeinit: Cleaning any existing connections...
[ 272.105000] DoVrgEndptDeinit: COMPLETED cleaning any existing connections.
[ 272.112000] DoVrgEndptDeinit: Deinitializing the endpoint...
[ 274.152000] dectshim close device...
[ 274.601000] finishVrgEndptDeinit: Deinitializing the board HAL...
[ 274.606000] [0;32m[INF xdrv_slic] deinitSiLabs: (ts: 15s 833ms):SLIC: De-initializing SiLabs FXS line 0
[ 274.606000] [0m
[ 274.618000] [0;32m[INF xdrv_slic] deinitSiLabs: (ts: 15s 845ms):SLIC: De-initializing SiLabs FXS line 1
[ 274.618000] [0m
[ 274.630000] [0;32m[INF xdrv_slic] deinitSiLabs: (ts: 15s 856ms):SLIC: SiLabs device 0 de-initialized OK
[ 274.630000] [0m
[ 274.644000] [0;33;41m[ERROR bos] bosErrorCheckStatusLinuxKernel,60: returned by bosSemGive: 2[0m
[ 274.664000] finishVrgEndptDeinit: COMPLETED deinitializing the board HAL.
[ 274.670000] kerSysDeregisterDyingGaspHandler: endpoint is deregistering
[ 274.677000] kerSysDeregisterDyingGaspHandler: endpoint is deregistered
[ 284.589000] mmConnKrnlBrcm: EXIT: unregister callbacks in endpointdd
[ 285.095000] mmConnKrnlBrcm: EXIT: COMPLETED
[ 285.113000] Endpoint: endpoint_cleanup entry
[ 285.117000] [0;33;41m[ERROR ept] boardHalSlicShutdown,3270: (ts: 26s 344ms):boardHalSlicShutdown: NOT IMPLEMENTED[0m
[ 285.145000] dect: unloading...
[ 285.147000] ### RsHookDead.
[ 285.150000] DECT Driver: Obtained Voice board id string (VANT-F)
[ 285.156000] DECT Driver: Obtained Base board id string (VANT-F)
[ 285.162000] DECT Driver: Successfully obtained voice parameters
[ 285.169000] DECT Driver: DECT RF Reset GPIO_8_AL
[ 285.178000] dect: Detected RF Frontend: LMX4181 rev A0
[ 285.248000] dect: exited
[ 297.065000] Endpoint: endpoint_init entry
[ 297.070000] Endpoint: endpoint_init COMPLETED
[ 297.214000] mmConnKrnlBrcm: INIT: num_rtpsock_ctx = 42
[ 297.218000] mmConnKrnlBrcm: INIT: COMPLETED
[ 298.498000] BOS: Enter bosInit
[ 298.500000] BOS: Exit bosInit
[ 298.694000] ******* DSP: Found BCM63268 *******
[ 298.698000] ******* DSP: In PCM Mode *******
[ 298.702000] ******* DSP: PCM running in 16 bit mode *******
[ 298.708000] gInterruptCounter = 0xC1A260B4
[ 298.712000] gInterruptErrors = 0xC1A260B0
[ 298.717000] gNextRxDesc = 0xC1A261E8
[ 298.722000] gNextTxDesc = 0xC1A261EC
[ 298.726000] gDectTestMode = 0xc1a261fc
[ 298.731000] dectBuffStart = 0xc1a261f0
[ 298.736000] gDectRxOutOfSyncCounter = 0xc1a26210
[ 298.740000] gDectTxOutOfSyncCounter = 0xc1a26214
[ 298.745000] 32 ms ECAN tail-length
[ 298.749000] *** gStartRxDesc[0] = 0xA7EF17D0
[ 298.753000] *** gBufferSizeBytes = 640
[ 298.757000] *** gStartTxDesc[0] = 0xA7EF1000
[ 298.762000] halPcmInit 367 nextTxDesc = 0xA7EF1000
[ 298.767000] halPcmInit 367 nextTxDesc = 0xA7EF1008
[ 298.772000] halPcmInit 371 Ownership for TX desc not set. Use this buffer.
[ 298.780000] Binding 0x85ebe678
[ 298.784000] [0;35m[DBG xdrv_slic] slicSi32261Init: (ts: 40s 11 ms):SLIC: Starting 32261 device and line initializion...[0m
[ 299.300000] [0;35m[DBG xdrv_slic] deviceSiLabsReset: (ts: 40s 526ms):SLIC: Reset applied on GPIO pin 15[0m
[ 299.314000] [0;35m[DBG xdrv_slic] initSiLabsDevice: (ts: 40s 540ms):SLIC: Initializing SiLabs device 0[0m
[ 300.624000] [0;35m[DBG xdrv_slic] initSiLabsDevice: (ts: 41s 851ms):SLIC: SiLabs device BOM Type: 6[0m
[ 300.633000] [0;35m[DBG xdrv_slic] initSiLabsDevice: (ts: 41s 860ms):SLIC: SiLabs device 0 initialized OK[0m
[ 300.644000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 41s 870ms):SLIC: SiLabs Locale set to 0[0m
[ 300.653000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 41s 880ms):SLIC: Initializing SiLabs FXS line 0[0m
[ 300.685000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 41s 911ms):FXS channel 0 Rx Gain: -9[0m
[ 300.693000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 41s 920ms):FXS channel 0 Tx Gain: -4[0m
[ 300.716000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 41s 943ms):SLIC: FXS line 0 RX timeslot = 0 [0m
[ 300.725000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 41s 952ms):SLIC: FXS line 0 TX timeslot = 0 [0m
[ 300.735000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 41s 962ms):SLIC: SiLabs FXS line 0 initialized OK[0m
[ 300.746000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 41s 972ms):SLIC: Initializing SiLabs FXS line 1[0m
[ 300.777000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 42s 3 ms):FXS channel 1 Rx Gain: -9[0m
[ 300.785000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 42s 12 ms):FXS channel 1 Tx Gain: -4[0m
[ 300.808000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 42s 35 ms):SLIC: FXS line 1 RX timeslot = 1 [0m
[ 300.817000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 42s 44 ms):SLIC: FXS line 1 TX timeslot = 1 [0m
[ 300.827000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 42s 54 ms):SLIC: SiLabs FXS line 1 initialized OK[0m
[ 300.838000] [0;35m[DBG xdrv_slic] slicSi32261Init: (ts: 42s 64 ms):SLIC: 32261 device 0 and FXS initializion COMPLETED OK ![0m
[ 301.381000] [0;35m[DBG xdrv_slic] OpenDaa : (ts: 42s 607ms): DAA DBG: Successful READ!!!! count = 0 [0m
[ 301.401000] [0;35m[DBG xdrv_slic] StartDaa : (ts: 42s 627ms): DAA DBG: ISOCAP lock count = 0 [0m
[ 301.413000] [0;35m[DBG xdrv_slic] StartDaa : (ts: 42s 640ms):Si3050 SLAC Initialised, Line side device = Si: 3019 (0x3)[0m
[ 301.424000] [0;35m[DBG xdrv_slic] StartDaa : (ts: 42s 651ms):System dev rev: 0x5, Line dev rev: 0x6[0m
[ 301.434000] [0;35m[DBG xdrv_slic] StartDaa : (ts: 42s 661ms):Line dev status: FDT:0x1, LCS: 0x0[0m
[ 301.444000] [0;35m[DBG xdrv_slic] StartDaa : (ts: 42s 670ms):DAA initialized with country code 0[0m
[ 301.453000] [0;35m[DBG xdrv_slic] daaSi3050Init: (ts: 42s 680ms):DAA Device Init completed. [0m
[ 301.462000] boardHalInit completed
[ 301.476000] DSP: Interrupt Ids
[ 301.479000] ---------------
[ 301.482000] InterruptId/Location = 42/HIGH
[ 301.486000]
[ 301.486000] DSP: Interrupt Masks
[ 301.491000] ---------------
[ 301.494000] IrqMask = 0x00000100
[ 301.499000] IrqMaskLow = 0x838066A0
[ 301.504000] IrqMask1 = 0x00000400
[ 301.509000] IrqMaskLow1 = 0x00000000
[ 301.514000] DSP: Interrupt Status
[ 301.519000] -----------------
[ 301.522000] IrqStatus = 0x00100000
[ 301.527000] IrqStatusLow = 0x08038100
[ 301.532000] IrqStatus1 = 0x00100000
[ 301.537000] IrqStatusLow1 = 0x08038100
[ 302.036000] EndpointInit completed
[ 302.039000] dgasp: kerSysRegisterDyingGaspHandler: endpoint registered
[ 302.212000] dectshim open device...
[ 302.215000] dectshim open device...
[ 302.218000] kernel::dectshim_ioctl: command 0
[ 302.224000] Kick dma Tx once
[ 302.226000] Kick dma Rx once
[ 302.230000] dectshim close device...
[ 302.313000] [0;35m[DBG xdrv_slic] daaSi3050ModeControl: (ts: 43s 539ms):DAA: Enable on-hook Caller ID receive. [0m
[ 302.376000] [0;33;41m[ERROR ept] ProvisionRingParams,3163: (ts: 43s 603ms):Ring offset of 25 not supported. Using default of 25 V for endpt 5[0m
[ 302.431000] [0;33;41m[ERROR ept] ProvisionRingParams,3163: (ts: 43s 658ms):Ring offset of 25 not supported. Using default of 25 V for endpt 4[0m
[ 307.502000] dect: Loading BCM6362 DECT Stack
[ 307.506000] dect: Version: , Build date: 2016/05/26, 20:05
[ 307.536000] ### RsHookReady 20160526 20:05
[ 307.540000] DECT DIP IRQ handler installed!
**** DectTestModePreInit:bTmp=0x00
ApiFpPcmTaskInit
[ 307.559000] ### RsHookRunning 2.
**** DectTestModeRunning:
dectshim open device...
[ 310.642000] kernel::dectshim_ioctl: command 5
[ 310.646000] dectshimGetVirtualAddr called
[ 310.650000] dectshim close device...
[ 310.661000] DECT Driver: Obtained Voice board id string (VANT-F)
[ 310.667000] DECT Driver: Obtained Base board id string (VANT-F)
[ 310.673000] DECT Driver: Successfully obtained voice parameter
[ 310.679000] DECT Driver: DECT RF Reset GPIO_8_AL
[ 310.687000] dect: Detected RF Frontend: LMX4181 rev A0
[ 363.139000] DoVrgEndptDeinit: Cleaning any existing connections...
[ 363.148000] DoVrgEndptDeinit: COMPLETED cleaning any existing connections.
[ 363.155000] DoVrgEndptDeinit: Deinitializing the endpoint...
[ 365.212000] dectshim close device...
[ 365.552000] finishVrgEndptDeinit: Deinitializing the board HAL...
[ 365.557000] [0;32m[INF xdrv_slic] deinitSiLabs: (ts: 46s 784ms):SLIC: De-initializing SiLabs FXS line 0
[ 365.557000] [0m
[ 365.569000] [0;32m[INF xdrv_slic] deinitSiLabs: (ts: 46s 796ms):SLIC: De-initializing SiLabs FXS line 1
[ 365.569000] [0m
[ 365.581000] [0;32m[INF xdrv_slic] deinitSiLabs: (ts: 46s 808ms):SLIC: SiLabs device 0 de-initialized OK
[ 365.581000] [0m
[ 365.595000] [0;33;41m[ERROR bos] bosErrorCheckStatusLinuxKernel,60: returned by bosSemGive: 2[0m
[ 365.614000] finishVrgEndptDeinit: COMPLETED deinitializing the board HAL.
[ 365.620000] kerSysDeregisterDyingGaspHandler: endpoint is deregistering
[ 365.627000] kerSysDeregisterDyingGaspHandler: endpoint is deregistered
[ 375.623000] mmConnKrnlBrcm: EXIT: unregister callbacks in endpointdd
[ 376.129000] mmConnKrnlBrcm: EXIT: COMPLETED
[ 376.148000] Endpoint: endpoint_cleanup entry
[ 376.151000] [0;33;41m[ERROR ept] boardHalSlicShutdown,3270: (ts: 57s 378ms):boardHalSlicShutdown: NOT IMPLEMENTED[0m
[ 376.179000] dect: unloading...
[ 376.182000] ### RsHookDead.
[ 376.185000] DECT Driver: Obtained Voice board id string (VANT-F)
[ 376.191000] DECT Driver: Obtained Base board id string (VANT-F)
[ 376.197000] DECT Driver: Successfully obtained voice parameters
[ 376.203000] DECT Driver: DECT RF Reset GPIO_8_AL
[ 376.211000] dect: Detected RF Frontend: LMX4181 rev A0
[ 376.284000] dect: exited
[ 387.978000] Endpoint: endpoint_init entry
[ 387.983000] Endpoint: endpoint_init COMPLETED
[ 388.132000] mmConnKrnlBrcm: INIT: num_rtpsock_ctx = 42
[ 388.136000] mmConnKrnlBrcm: INIT: COMPLETED
[ 389.419000] BOS: Enter bosInit
[ 389.421000] BOS: Exit bosInit
[ 389.620000] ******* DSP: Found BCM63268 *******
[ 389.624000] ******* DSP: In PCM Mode *******
[ 389.628000] ******* DSP: PCM running in 16 bit mode *******
[ 389.634000] gInterruptCounter = 0xC22A80B4
[ 389.638000] gInterruptErrors = 0xC22A80B0
[ 389.643000] gNextRxDesc = 0xC22A81E8
[ 389.648000] gNextTxDesc = 0xC22A81EC
[ 389.652000] gDectTestMode = 0xc22a81fc
[ 389.657000] dectBuffStart = 0xc22a81f0
[ 389.662000] gDectRxOutOfSyncCounter = 0xc22a8210
[ 389.667000] gDectTxOutOfSyncCounter = 0xc22a8214
[ 389.671000] 32 ms ECAN tail-length
[ 389.675000] *** gStartRxDesc[0] = 0xA7EF1000
[ 389.679000] *** gBufferSizeBytes = 640
[ 389.683000] *** gStartTxDesc[0] = 0xA7EF17D0
[ 389.688000] halPcmInit 367 nextTxDesc = 0xA7EF17D0
[ 389.693000] halPcmInit 367 nextTxDesc = 0xA7EF17D8
[ 389.698000] halPcmInit 371 Ownership for TX desc not set. Use this buffer.
[ 389.705000] Binding 0x88c4f388
[ 389.710000] [0;35m[DBG xdrv_slic] slicSi32261Init: (ts: 10s 937ms):SLIC: Starting 32261 device and line initializion...[0m
[ 390.226000] [0;35m[DBG xdrv_slic] deviceSiLabsReset: (ts: 11s 452ms):SLIC: Reset applied on GPIO pin 15[0m
[ 390.240000] [0;35m[DBG xdrv_slic] initSiLabsDevice: (ts: 11s 466ms):SLIC: Initializing SiLabs device 0[0m
[ 391.552000] [0;35m[DBG xdrv_slic] initSiLabsDevice: (ts: 12s 779ms):SLIC: SiLabs device BOM Type: 6[0m
[ 391.561000] [0;35m[DBG xdrv_slic] initSiLabsDevice: (ts: 12s 788ms):SLIC: SiLabs device 0 initialized OK[0m
[ 391.572000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 12s 798ms):SLIC: SiLabs Locale set to 0[0m
[ 391.581000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 12s 808ms):SLIC: Initializing SiLabs FXS line 0[0m
[ 391.613000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 12s 839ms):FXS channel 0 Rx Gain: -9[0m
[ 391.621000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 12s 848ms):FXS channel 0 Tx Gain: -4[0m
[ 391.644000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 12s 871ms):SLIC: FXS line 0 RX timeslot = 0 [0m
[ 391.654000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 12s 880ms):SLIC: FXS line 0 TX timeslot = 0 [0m
[ 391.663000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 12s 890ms):SLIC: SiLabs FXS line 0 initialized OK[0m
[ 391.674000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 12s 900ms):SLIC: Initializing SiLabs FXS line 1[0m
[ 391.706000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 12s 932ms):FXS channel 1 Rx Gain: -9[0m
[ 391.714000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 12s 941ms):FXS channel 1 Tx Gain: -4[0m
[ 391.737000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 12s 964ms):SLIC: FXS line 1 RX timeslot = 1 [0m
[ 391.747000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 12s 973ms):SLIC: FXS line 1 TX timeslot = 1 [0m
[ 391.756000] [0;35m[DBG xdrv_slic] initSiLabsLines: (ts: 12s 983ms):SLIC: SiLabs FXS line 1 initialized OK[0m
[ 391.767000] [0;35m[DBG xdrv_slic] slicSi32261Init: (ts: 12s 994ms):SLIC: 32261 device 0 and FXS initializion COMPLETED OK ![0m
[ 392.310000] [0;35m[DBG xdrv_slic] OpenDaa : (ts: 13s 536ms): DAA DBG: Successful READ!!!! count = 0 [0m
[ 392.329000] [0;35m[DBG xdrv_slic] StartDaa : (ts: 13s 555ms): DAA DBG: ISOCAP lock count = 0 [0m
[ 392.341000] [0;35m[DBG xdrv_slic] StartDaa : (ts: 13s 568ms):Si3050 SLAC Initialised, Line side device = Si: 3019 (0x3)[0m
[ 392.352000] [0;35m[DBG xdrv_slic] StartDaa : (ts: 13s 579ms):System dev rev: 0x5, Line dev rev: 0x6[0m
[ 392.362000] [0;35m[DBG xdrv_slic] StartDaa : (ts: 13s 589ms):Line dev status: FDT:0x1, LCS: 0x0[0m
[ 392.371000] [0;35m[DBG xdrv_slic] StartDaa : (ts: 13s 598ms):DAA initialized with country code 0[0m
[ 392.381000] [0;35m[DBG xdrv_slic] daaSi3050Init: (ts: 13s 608ms):DAA Device Init completed. [0m
[ 392.390000] boardHalInit completed
[ 392.403000] DSP: Interrupt Ids
[ 392.406000] ---------------
[ 392.409000] InterruptId/Location = 42/HIGH
[ 392.413000]
[ 392.413000] DSP: Interrupt Masks
[ 392.418000] ---------------
[ 392.421000] IrqMask = 0x00000100
[ 392.426000] IrqMaskLow = 0x838066A0
[ 392.431000] IrqMask1 = 0x00000400
[ 392.436000] IrqMaskLow1 = 0x00000000
[ 392.441000] DSP: Interrupt Status
[ 392.446000] -----------------
[ 392.449000] IrqStatus = 0x00100000
[ 392.454000] IrqStatusLow = 0x08038100
[ 392.459000] IrqStatus1 = 0x00100000
[ 392.464000] IrqStatusLow1 = 0x08038100
[ 392.963000] EndpointInit completed
[ 392.966000] dgasp: kerSysRegisterDyingGaspHandler: endpoint registered
[ 393.137000] dectshim open device...
[ 393.140000] dectshim open device...
[ 393.144000] kernel::dectshim_ioctl: command 0
[ 393.150000] Kick dma Tx once
[ 393.152000] Kick dma Rx once
[ 393.156000] dectshim close device...
[ 393.239000] [0;35m[DBG xdrv_slic] daaSi3050ModeControl: (ts: 14s 465ms):DAA: Enable on-hook Caller ID receive. [0m
[ 393.302000] [0;33;41m[ERROR ept] ProvisionRingParams,3163: (ts: 14s 529ms):Ring offset of 25 not supported. Using default of 25 V for endpt 5[0m
[ 393.357000] [0;33;41m[ERROR ept] ProvisionRingParams,3163: (ts: 14s 584ms):Ring offset of 25 not supported. Using default of 25 V for endpt 4[0m
[ 398.463000] dect: Loading BCM6362 DECT Stack
[ 398.467000] dect: Version: , Build date: 2016/05/26, 20:05
[ 398.502000] ### RsHookReady 20160526 20:05
[ 398.505000] DECT DIP IRQ handler installed!
**** DectTestModePreInit:bTmp=0x00
ApiFpPcmTaskInit
[ 398.527000] ### RsHookRunning 2.
**** DectTestModeRunning:
dectshim open device...
[ 401.774000] kernel::dectshim_ioctl: command 5
[ 401.779000] dectshimGetVirtualAddr called
[ 401.783000] dectshim close device...
[ 401.795000] DECT Driver: Obtained Voice board id string (VANT-F)
[ 401.800000] DECT Driver: Obtained Base board id string (VANT-F)
[ 401.806000] DECT Driver: Successfully obtained voice parameters
[ 401.812000] DECT Driver: DECT RF Reset GPIO_8_AL
[ 401.823000] dect: Detected RF Frontend: LMX4181 rev A0
