OpenWrt Forum Archive

Topic: Buffalo WHR-G125 console messages

The content of this topic has been archived on 4 May 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

Post #1
kuroguy
31 May 2007, 20:58

Booted a dd-wrt 2.4 beta version:

Opening COM6...

> Baud Rate             : 115200
> Byte Size             : 8
> Parity                : None
> Stop Bits             : 1
> Hardware Flow Control : None
> Software Flow Control : None
> RS485 Mode            : Off

COM6 Ready!
Decompressing..........done
>0x80FFFFFF>complite


CFE version 1.0.37-1.18 for BCM947XX (32bit,SP,LE)
Build Date: 2007ǯ  2·î 21Æü ¿åÍËÆü 19:53:30 JST (root@Satoh-linux2)
  Build Type: CFG_MINIMAL_SIZE
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Modified by Buffalo inc.

Initializing Arena
Initializing Devices.
Boot partition size = 131072(0x20000)
* cmdset: AMD Standard
* Insaner_1 = (0xa2)
* flashutl_cmd: type (0004), read_id (0090)
-> vendid (00EC), devid (22A2), devid2 (0000)
* flashutl_cmd: type (0003), read_id (0090)
-> vendid (00EC), devid (22A2), devid2 (0000)
* flashutl_cmd: type (0002), read_id (0090)
-> vendid (0000), devid (3C08), devid2 (0000)
* Flash Info. -> manufacturer (00), device (00)
* Flash Info. -> manufacturer2 (0000), device2 (0000)
* Insaner_2 = (0xa2)
* cmdset: AMD Standard
* Insaner_1 = (0xa2)
* flashutl_cmd: type (0004), read_id (0090)
-> vendid (00EC), devid (22A2), devid2 (0000)
* flashutl_cmd: type (0003), read_id (0090)
-> vendid (00EC), devid (22A2), devid2 (0000)
* flashutl_cmd: type (0002), read_id (0090)
-> vendid (0000), devid (3C08), devid2 (0000)
* Flash Info. -> manufacturer (00), device (00)
* Flash Info. -> manufacturer2 (0000), device2 (0000)
* Insaner_2 = (0xa2)
* cmdset: AMD Standard
* Insaner_1 = (0xa2)
* flashutl_cmd: type (0004), read_id (0090)
-> vendid (00EC), devid (22A2), devid2 (0000)
* flashutl_cmd: type (0003), read_id (0090)
-> vendid (00EC), devid (22A2), devid2 (0000)
* flashutl_cmd: type (0002), read_id (0090)
-> vendid (0000), devid (3C08), devid2 (0000)
* Flash Info. -> manufacturer (00), device (00)
* Flash Info. -> manufacturer2 (0000), device2 (0000)
* Insaner_2 = (0xa2)
nvram_check: flash_base=(0x1c000000)
nvram_check: return(0)
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.130.23.0
* memc_config: (000C800B)
CPU type 0x29029: 240MHz
Total memory: 16384 KBytes

Total memory used by CFE:  0x80400000 - 0x8049E900 (649472)
Initialized Data:          0x80433DC0 - 0x80436E90 (12496)
BSS Area:                  0x80436E90 - 0x80438900 (6768)
Local Heap:                0x80438900 - 0x8049C900 (409600)
Stack Area:                0x8049C900 - 0x8049E900 (8192)
Text (code) segment:       0x80400000 - 0x80433DC0 (212416)
Boot area (physical):      0x0049F000 - 0x004DF000
Relocation Factor:         I:00000000 - D:00000000

Device eth0:  hwaddr 00-16-01-9A-18-B8, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
Wait a few seconds for an image
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: Failed.
Could not load :: Timeout occured
>>> boot -raw -z -addr=0x80001000 -max=0x3a0000 flash0.os:
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3732 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
CPU revision is: 00029029
Linux version 2.4.34 (root@dd-wrt) (gcc version 3.4.4 (OpenWrt-2.0)) #57 Wed May
30 05:40:58 CEST 2007
Setting the PFC to its default value
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd cons
ole=ttyS0,115200
CPU: BCM5354 rev 1 at 240 MHz
Using 120.000 MHz high precision timer.
Calibrating delay loop... 237.56 BogoMIPS
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
PCI: no core
PCI: Fixing up bus 0
Initializing RT netlink socket
Starting kswapd
pty: 256 Unix98 ptys configured
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-o
nly
ip_conntrack version 2.1 (512 buckets, 4096 max) - 336 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_random match loaded
netfilter PSD loaded - (c) astaro AG
ipt_IPV4OPTSSTRIP loaded
VFS: Mounted root (squashfs filesystem) readonly.
Booting Device:Buffalo WHR-G125
eth1: No such device
Warning: loading diag will taint the kernel: no license
  See http://www.tux.org/lkml/#export-tainted for information about tainted modu
les
Warning: loading switch-core will taint the kernel: no license
  See http://www.tux.org/lkml/#export-tainted for information about tainted modu
les
Warning: loading switch-robo will taint the kernel: no license
  See http://www.tux.org/lkml/#export-tainted for information about tainted modu
les
boardflags are 0x0750
Warning: loading wl will taint the kernel: no license
  See http://www.tux.org/lkml/#export-tainted for information about tainted modu
les
sb_doattach: incoming bus is PCI but it's a lie, switching to SB devid:0x4318
eth1: Broadcom BCM4318 802.11 Wireless Controller 4.130.25.0
nvram_commit(): end
br0: Bad file descriptor
br0: Bad file descriptor
eth1: Operation not supported
eth1: Invalid argument
eth1: Invalid argument
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
Warning: loading ip_conntrack_proto_gre will taint the kernel: no license
  See http://www.tux.org/lkml/#export-tainted for information about tainted modu
les
Warning: loading ip_nat_proto_gre will taint the kernel: no license
  See http://www.tux.org/lkml/#export-tainted for information about tainted modu
les
Warning: loading ip_conntrack_pptp will taint the kernel: no license
  See http://www.tux.org/lkml/#export-tainted for information about tainted modu
les
Warning: loading ip_nat_pptp will taint the kernel: no license
  See http://www.tux.org/lkml/#export-tainted for information about tainted modu
les
Warning: loading ip_conntrack_proto_gre will taint the kernel: no license
  See http://www.tux.org/lkml/#export-tainted for information about tainted modu
les
Warning: loading ip_nat_proto_gre will taint the kernel: no license
  See http://www.tux.org/lkml/#export-tainted for information about tainted modu
les
Warning: loading ip_conntrack_pptp will taint the kernel: no license
  See http://www.tux.org/lkml/#export-tainted for information about tainted modu
les
Warning: loading ip_nat_pptp will taint the kernel: no license
  See http://www.tux.org/lkml/#export-tainted for information about tainted modu
les
vlan1: Setting MAC address to  00 16 01 9a 18 b9.
udhcpc (v0.9.9-pre) started
Jan  1 00:00:08 udhcpc[177]: udhcpc (v0.9.9-pre) started
sh: /tmp/.rc_startup: not found
Sending discover...
Jan  1 00:00:08 udhcpc[177]: Sending discover...
/tmp/smbshare
Sending discover...
Jan  1 00:00:12 udhcpc[177]: Sending discover...

DD-WRT v24 std (c) 2007 NewMedia-NET GmbH
Release: 05/30/07 (SVN revision: 7139)
ÿ
whr-g125 login: DD-WRT v24 std (c) 2007 NewMedia-NET GmbH
Release: 05/30/07 (SVN revision: 7139)
ÿ
whr-g125 login:

(Last edited by kuroguy on 31 May 2007, 21:00)

Post #2
kuroguy
14 Jun 2007, 02:13

Here's the boot messages with the Broadcom-2.4 Kamikaze firmware on it:


* Flash Info. -> manufacturer2 (0000), device2 (0000)
* Insaner_2 = (0xa2)
* cmdset: AMD Standard
* Insaner_1 = (0xa2)
* flashutl_cmd: type (0004), read_id (0090)
-> vendid (00EC), devid (22A2), devid2 (0000)
* flashutl_cmd: type (0003), read_id (0090)
-> vendid (00EC), devid (22A2), devid2 (0000)
* flashutl_cmd: type (0002), read_id (0090)
-> vendid (0000), devid (3C08), devid2 (0000)
* Flash Info. -> manufacturer (00), device (00)
* Flash Info. -> manufacturer2 (0000), device2 (0000)
* Insaner_2 = (0xa2)
nvram_check: flash_base=(0x1c000000)
nvram_check: return(0)
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.130.23.0
* memc_config: (000C800B)
CPU type 0x29029: 240MHz
Total memory: 16384 KBytes

Total memory used by CFE:  0x80400000 - 0x8049E900 (649472)
Initialized Data:          0x80433DC0 - 0x80436E90 (12496)
BSS Area:                  0x80436E90 - 0x80438900 (6768)
Local Heap:                0x80438900 - 0x8049C900 (409600)
Stack Area:                0x8049C900 - 0x8049E900 (8192)
Text (code) segment:       0x80400000 - 0x80433DC0 (212416)
Boot area (physical):      0x0049F000 - 0x004DF000
Relocation Factor:         I:00000000 - D:00000000

Device eth0:  hwaddr 00-16-01-9A-18-B8, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
Wait a few seconds for an image
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: Failed.
Could not load :: Timeout occured
>>> boot -raw -z -addr=0x80001000 -max=0x3a0000 flash0.os:
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3732 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000

Post #3
capaz
29 Jul 2007, 15:17

Hi kuroguy!

How did you get those messages? do you have the schematics on Jtag or serial for the whr-g125?

Do you know the state of developemnt for this model?

How can I help?

Post #4
XIONG
14 May 2008, 16:08

For three years, if I see that as early as it can help you, but I do not know that you need it now ?

The discussion might have continued from here.