Hello, (sorry for my english)
I have updated from the kamikaze 7.09 rev 9533 to the new 9792, and my wireless (Atheros) has finished to work.

Please help me.

This is my kernel log.

Linux version 2.6.23.9 (alex@linux-alex-megasys) (gcc version 4.1.2) #2 SMP Tue Dec 18 16:37:15 CET 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000004000000 (usable)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
64MB LOWMEM available.
Entering add_active_range(0, 0, 16384) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->    16384
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->    16384
On node 0 totalpages: 16384
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 96 pages used for memmap
  Normal zone: 12192 pages, LIFO batch:1
  Movable zone: 0 pages used for memmap
DMI not present or invalid.
Allocating PCI resources starting at 10000000 (gap: 04000000:fbf00000)
Built 1 zonelists in Zone order.  Total pages: 16256
Kernel command line: root=/dev/hda2 rootfstype=ext2 init=/etc/preinit  noinitrd console=tty0 console=ttyS0,38400n8 reboot=bios
No local APIC present or hardware disabled
mapped APIC to ffffb000 (0108a000)
Initializing CPU#0
PID hash table entries: 256 (order: 8, 1024 bytes)
Detected 233.320 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 61956k/65536k available (1521k kernel code, 3176k reserved, 591k data, 184k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xfffb9000 - 0xfffff000   ( 280 kB)
    vmalloc : 0xc4800000 - 0xfffb7000   ( 951 MB)
    lowmem  : 0xc0000000 - 0xc4000000   (  64 MB)
      .init : 0xc0317000 - 0xc0345000   ( 184 kB)
      .data : 0xc027c426 - 0xc03101fc   ( 591 kB)
      .text : 0xc0100000 - 0xc027c426   (1521 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 468.05 BogoMIPS (lpj=2340298)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 00808131 01818131 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After all inits, caps: 00808131 00818131 00000000 00000001 00000000 00000000 00000000 00000000
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 11k freed
CPU0: NSC Unknown stepping 01
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfc47b, last bus=0
PCI: Using configuration type 1
Setting up standard PCI resources
Linux Plug and Play Support v0.97 (c) Adam Belay
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Device 0000:00:12.5 not found by BIOS
Time: tsc clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 24576 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
microcode: CPU0 not a capable Intel processor
IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
scx200: NatSemi SCx200 Driver
scx200: GPIO base 0xf400
scx200: Configuration Block base 0x9000
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SC1200: IDE controller at PCI slot 0000:00:12.2
SC1200: chipset revision 1
SC1200: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: CF 1GB, ATA DISK drive
Clocksource tsc unstable (delta = -455377516 ns)
Time: pit clocksource has been installed.
hda: selected mode 0x22
hda: sc1200_set_xfer_mode(MW DMA 2)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: max request size: 128KiB
hda: 2030112 sectors (1039 MB) w/1KiB Cache, CHS=2014/16/63, DMA
hda: hda1 hda2
block2mtd: version $Revision: 1.30 $
PNP: No PS/2 controller found. Probing ports directly.
i8042.c: No controller found.
mice: PS/2 mouse device common for all mice
enabling scx200 high-res timer (1 MHz +0 ppm)
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
Time: scx200_hrt clocksource has been installed.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP vegas registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Using IPI Shortcut mode
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 184k freed
Warning: unable to open an initial console.
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
natsemi dp8381x driver, version 2.1, Sept 11, 2006
  originally by Donald Becker <becker@scyld.com>
  2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
natsemi eth0: NatSemi DP8381[56] at 0x80000000 (0000:00:0e.0), 00:0d:b9:06:00:f4, IRQ 10, port TP.
br-lan: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
PPP generic driver version 2.4.2
device eth0 entered promiscuous mode
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
br-lan: port 1(eth0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 1(eth0) entering forwarding state
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
IPP2P v0.8.1_rc1 loading
IMQ starting with 2 devices...
IMQ driver loaded successfully.
    Hooking IMQ before NAT on PREROUTING.
    Hooking IMQ after NAT on POSTROUTING.
ipt_time loading
wlan: 0.8.4.2 (0.9.4)
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.30.13 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133)
ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (0.9.4)
ath_rate_minstrel: look around rate set to 10%
ath_rate_minstrel: EWMA rolloff level set to 75%
ath_rate_minstrel: max segment size in the mrr set to 6000 us
wlan: mac acl policy registered
ath_pci: 0.9.4.5 (0.9.4)
HAL returned 23 channels.
Channel   1 (2412 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_CCK CF_2GHZ
Channel   1 (2412 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_OFDM CF_2GHZ
Channel   2 (2417 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_CCK CF_2GHZ
Channel   2 (2417 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_OFDM CF_2GHZ
Channel   3 (2422 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_CCK CF_2GHZ
Channel   3 (2422 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_OFDM CF_2GHZ
Channel   4 (2427 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_CCK CF_2GHZ
Channel   4 (2427 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_OFDM CF_2GHZ
Channel   5 (2432 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_CCK CF_2GHZ
Channel   5 (2432 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_OFDM CF_2GHZ
Channel   6 (2437 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_CCK CF_2GHZ
Channel   6 (2437 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_OFDM CF_2GHZ
Channel   6 (2437 MHz) Max Tx Power 15 dBm (hw limited) [15 hw 20 reg] Flags CF_TURBO CF_OFDM CF_2GHZ
Channel   7 (2442 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_CCK CF_2GHZ
Channel   7 (2442 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_OFDM CF_2GHZ
Channel   8 (2447 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_CCK CF_2GHZ
Channel   8 (2447 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_OFDM CF_2GHZ
Channel   9 (2452 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_CCK CF_2GHZ
Channel   9 (2452 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_OFDM CF_2GHZ
Channel  10 (2457 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_CCK CF_2GHZ
Channel  10 (2457 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_OFDM CF_2GHZ
Channel  11 (2462 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_CCK CF_2GHZ
Channel  11 (2462 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 27 reg] Flags CF_OFDM CF_2GHZ
ath_pci: switching rfkill capability off
ath_pci: switching per-packet transmit power control off
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: mac 5.9 phy 4.3 radio 4.6
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
wifi0: Atheros 5212: mem=0x80040000, irq=9
ne2k-pci.c:v1.03 9/22/2003 D. Becker/P. Gortmaker