Hello,
This is the setup I have (Linksys WRT54GL with Kamikaze 7.09):
STATIC IP 192.168.0.10 WAN 192.168.0.77 LAN 192.168.25.10
----------------- ------------- ------------------------
INTERNET ------| Firewall box |--------------| SWITCH |---------------------| Linksys WRT54GL |
----------------- ------------- ------------------------
| | | | |
---------------------------------------------- | | | |
| ------------------------------ | | |
| | | | |
---------- ----------- -------------------- ----------------------- -----------------------
| DNS 1 | | DNS 2 | | ASTERISK PBX | | PCs, IP PHONES.. | | PCs, IP PHONES.. |
---------- ----------- -------------------- ----------------------- -----------------------
192.168.0.2 192.168.0.5 192.168.0.40 192.168.0.x/24 192.168.25.x/24
The PCs connected to the LAN port of the WRT54GL can't see (ping) the systems on the subnet connected to the WAN port, nor reach the Internet and the systems on the WAN side of the WRT54GL can't reach the ones on the LAN side. Wifi doesn't work either (SSID is visible but cannot get an IP address).
This is the content of my config files :
NETWORK
------------
#### VLAN configuration
config switch eth0
option vlan0 "0 1 2 3 5*"
option vlan1 "4 5"
#### Loopback configuration
config interface loopback
option ifname "lo"
option proto "static"
option ipaddr "127.0.0.1"
option netmask "255.0.0.0"
#### LAN configuration
config interface lan
option type "bridge"
option ifname "eth0.0"
option proto "static"
option ipaddr "192.168.25.10"
option netmask "255.255.255.0"
#### WAN configuration
config interface wan
option ifname "eth0.1"
option proto "static"
option ipaddr "192.168.0.77"
option netmask "255.255.255.0"
option gateway "192.168.0.10"
option dns "192.168.0.2 192.168.0.5 212.68.193.110 212.68.193.32"
WIRELESS
------------
config wifi-device wl0
option type broadcom
option channel 11
# REMOVE THIS LINE TO ENABLE WIFI:
# option disabled 1
config wifi-iface
option device wl0
option network lan
option mode ap
option ssid FINBRUS
option encryption psk
option key Ao4ptbFINBRUS!
DNSMASQ.CONF
-------------------
# filter what we send upstream
domain-needed
bogus-priv
filterwin2k
localise-queries
# allow /etc/hosts and dhcp lookups via *.lan
local=/lan/
domain=lan
expand-hosts
no-negcache
resolv-file=/tmp/resolv.conf.auto
dhcp-range=192.168.25.100,192.168.25.150,255.255.255.0
dhcp-authoritative
dhcp-leasefile=/tmp/dhcp.leases
# use /etc/ethers for static hosts; same format as --dhcp-host
# <hwaddr> <ipaddr>
read-ethers
# other useful options:
# default route(s): dhcp-option=3,192.168.1.1,192.168.1.2
# dns server(s): dhcp-option=6,192.168.1.1,192.168.1.2
dhcp-option=6,192.168.0.2,192.168.0.5,212.68.193.110,212.68.193.32
dhcp-option=66,192.168.0.40
dhcp-option=150,192.168.0.40
Is there something I missed? I've been searching for two days without any success, so any help would be mostly appreciated.