Hi, I'm trying to install a USB bluetooth adapter and a USB Audio adapter. But non of them get reconized. What I'm doing wrong? I'm using Kamikaze svn 10443 with 2.6er Kernel.
The Bluetooth and Audio USB adapter are connected to my Asus wl-500gP with a 4 Port USB 1.1 HUB. If I connect them without the HUB nothing get changed. Here are my outputs:
dmesg output
Linux version 2.6.23.16 (oconnor@dell) (gcc version 4.1.2) #15 Wed Feb 27 22:10:52 CET 2008
CPU revision is: 00029006
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x03, vendor 0x4243)
ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
ssb: Core 2 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x02, vendor 0x4243)
ssb: Core 4 found: PCI (cc 0x804, rev 0x08, vendor 0x4243)
ssb: Core 5 found: MIPS 3302 (cc 0x816, rev 0x00, vendor 0x4243)
ssb: Core 6 found: V90 (cc 0x807, rev 0x02, vendor 0x4243)
ssb: Core 7 found: IPSEC (cc 0x80B, rev 0x00, vendor 0x4243)
ssb: Core 8 found: MEMC SDRAM (cc 0x80F, rev 0x00, vendor 0x4243)
ssb: Initializing MIPS core...
ssb: set_irq: core 0x0806, irq 2 => 2
ssb: set_irq: core 0x0806, irq 3 => 3
ssb: set_irq: core 0x0804, irq 0 => 4
ssb: Sonics Silicon Backplane found at address 0x18000000
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
On node 0 totalpages: 8192
Normal zone: 64 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 8128 pages, LIFO batch:0
Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order. Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 init=/etc/preinit noinitrd console=ttyS0,115200
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (21 instructions).
Synthesized TLB load handler fastpath (33 instructions).
Synthesized TLB store handler fastpath (33 instructions).
Synthesized TLB modify handler fastpath (32 instructions).
PID hash table entries: 128 (order: 7, 512 bytes)
Using 132.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29908k/32768k available (2009k kernel code, 2860k reserved, 286k data, 120k init, 0k highmem)
Calibrating delay loop... 262.14 BogoMIPS (lpj=524288)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
ssb: PCIcore in host mode found
registering PCI controller with io_map_base unset
PCI: fixing up bridge
PCI: Setting latency timer of device 0000:00:00.0 to 64
PCI: Fixing up device 0000:00:00.0
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
detected lzma initramfs
initramfs: LZMA lc=1,lp=2,pb=2,origSize=512
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 3) is a 16550A
b44.c:v1.01 (Jun 16, 2006)
eth0: Broadcom 10/100BaseT Ethernet 00:18:f3:98:e1:af
eth1: Broadcom 10/100BaseT Ethernet 40:10:18:00:00:2d
flash init: 0x1c000000 0x02000000
Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Amd/Fujitsu Extended Query Table at 0x0040
Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x800000 at 0x1fc00000
bootloader size: 262144
Creating 4 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x007f0000 : "linux"
0x000f5400-0x007f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=6B0000, len=140000
0x006b0000-0x007f0000 : "rootfs_data"
0x007f0000-0x00800000 : "nvram"
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP vegas registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 120k freed
Please be patient, while OpenWrt loads ...
Algorithmics/MIPS FPU Emulator v1.5
diag: Detected 'ASUS WL-500g Premium'
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
Probing device eth0: found!
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
br-lan: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device eth0.0 entered promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0.0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 1(eth0.0) entering forwarding state
SCSI subsystem initialized
BFL_ENETADM not set in boardflags. Use force=1 to ignore.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PPP generic driver version 2.4.2
wlan: trunk
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.30.13 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, REGOPS_FUNC)
ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (trunk)
ath_rate_minstrel: look around rate set to 10%
ath_rate_minstrel: EWMA rolloff level set to 75%
ath_rate_minstrel: max segment size in the mrr set to 6000 us
wlan: mac acl policy registered
ath_pci: trunk
PCI: Enabling device 0000:00:02.0 (0000 -> 0002)
PCI: Fixing up device 0000:00:02.0
MadWifi: ath_attach: Switching rfkill capability off
MadWifi: ath_attach: Switching per-packet transmit power control off
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: ath_announce: Use hw queue 1 for WME_AC_BE traffic
wifi0: ath_announce: Use hw queue 0 for WME_AC_BK traffic
wifi0: ath_announce: Use hw queue 2 for WME_AC_VI traffic
wifi0: ath_announce: Use hw queue 3 for WME_AC_VO traffic
wifi0: ath_announce: Use hw queue 8 for CAB traffic
wifi0: ath_announce: Use hw queue 9 for beacons
ath_pci: wifi0: Atheros 5212: mem=0x40000000, irq=6
USB Universal Host Controller Interface driver v3.0
PCI: Enabling device 0000:00:03.0 (0000 -> 0001)
PCI: Fixing up device 0000:00:03.0
uhci_hcd 0000:00:03.0: UHCI Host Controller
uhci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:03.0: irq 6, io base 0x00000100
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Enabling device 0000:00:03.1 (0000 -> 0001)
PCI: Fixing up device 0000:00:03.1
uhci_hcd 0000:00:03.1: UHCI Host Controller
uhci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:03.1: irq 6, io base 0x00000120
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Enabling device 0000:00:03.2 (0000 -> 0002)
PCI: Fixing up device 0000:00:03.2
ehci_hcd 0000:00:03.2: EHCI Host Controller
ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:03.2: irq 6, io mem 0x40010000
usb 1-1: new full speed USB device using uhci_hcd and address 2
ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
usb 3-2: new high speed USB device using ehci_hcd and address 3
usb 3-2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver snd-usb-audio
usb 1-1: new full speed USB device using uhci_hcd and address 3
Initializing USB Mass Storage driver...
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 5 ports detected
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usb 1-1.2: new full speed USB device using uhci_hcd and address 4
usb 1-1.2: configuration #1 chosen from 1 choice
usb 1-1.3: new full speed USB device using uhci_hcd and address 5
usb 1-1.3: configuration #1 chosen from 1 choice
usb 1-1.5: new full speed USB device using uhci_hcd and address 6
usb 1-1.5: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
Linux video capture interface: v2.00
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.5
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: BNEP (Ethernet Emulation) ver 1.2
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCI BCSP protocol initialized
Bluetooth: HCI USB driver ver 2.9
usbcore: registered new interface driver hci_usb
/home/oconnor/Desktop/trunk/build_dir/linux-brcm47xx/spca5xx-le/spca_core.c: USB SPCA5XX camera found. Type Mustek gSmart Mini 3(SPCA504A)
usbcore: registered new interface driver spca5xx
/home/oconnor/Desktop/trunk/build_dir/linux-brcm47xx/spca5xx-le/spca_core.c: spca5xx driver 00.57.06LE registered
scsi 0:0:0:0: Direct-Access Verbatim Store'n'go U3 6.15 PQ: 0 ANSI: 0 CCS
sd 0:0:0:0: [sda] 1994751 512-byte hardware sectors (1021 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 45 00 00 08
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] 1994751 512-byte hardware sectors (1021 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 45 00 00 08
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk
usb-storage: device scan complete
EXT2-fs: sda1: couldn't mount because of unsupported optional features (4).
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT3 FS on sda1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.logread output
Jan 1 00:00:11 AsusP syslog.info syslogd started: BusyBox v1.8.2
Jan 1 00:00:11 AsusP user.notice kernel: klogd started: BusyBox v1.8.2 (2008-02-15 21:05:39 CET)
Jan 1 00:00:12 AsusP user.info kernel: b44: eth0: Link is up at 100 Mbps, full duplex.
Jan 1 00:00:12 AsusP user.info kernel: b44: eth0: Flow control is off for TX and off for RX.
Jan 1 00:00:14 kernel: br-lan: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
Jan 1 00:00:14 AsusP user.info kernel: device eth0.0 entered promiscuous mode
Jan 1 00:00:14 AsusP user.info kernel: device eth0 entered promiscuous mode
Jan 1 00:00:14 kernel: br-lan: port 1(eth0.0) entering learning state
Jan 1 00:00:14 kernel: br-lan: topology change detected, propagating
Jan 1 00:00:14 kernel: br-lan: port 1(eth0.0) entering forwarding state
Jan 1 00:00:14 AsusP user.notice kernel: SCSI subsystem initialized
Jan 1 00:00:14 AsusP user.info kernel: t set in boardflags. Use force=1 to ignore.
Jan 1 00:00:14 kernel: BFL_ENETADM no
Jan 1 00:00:15 kernel: usbcore: registered new interface driver usbfs
Jan 1 00:00:15 kernel: usbcore: registered new interface driver hub
Jan 1 00:00:15 AsusP user.info kernel: usbcore: registered new device driver usb
Jan 1 00:00:15 : udhcpc (v1.8.2) started
Jan 1 00:00:16 : Sending discover...
Jan 1 00:00:16 kernel: PPP generic driver version 2.4.2
Jan 1 00:00:19 AsusP user.info kernel: wlan: trunk
Jan 1 00:00:19 kernel: ath_hal: module license 'Proprietary' taints kernel.
Jan 1 00:00:19 kernel: ath_hal: 0.9.30.13 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, REGOPS_FUNC)
Jan 1 00:00:19 : Sending discover...
Jan 1 00:00:19 AsusP user.info kernel: ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (trunk)
Jan 1 00:00:19 AsusP user.info kernel: ath_rate_minstrel: look around rate set to 10%
Jan 1 00:00:19 AsusP user.info kernel: ath_rate_minstrel: EWMA rolloff level set to 75%
Jan 1 00:00:19 AsusP user.info kernel: ath_rate_minstrel: max segment size in the mrr set to 6000 us
Jan 1 00:00:19 kernel: wlan: mac acl policy registered
Jan 1 00:00:20 AsusP user.info kernel: ath_pci: trunk
Jan 1 00:00:20 AsusP user.warn kernel: PCI: Enabling device 0000:00:02.0 (0000 -> 0002)
Jan 1 00:00:20 AsusP user.info kernel: PCI: Fixing up device 0000:00:02.0
Jan 1 00:00:20 AsusP user.info kernel: MadWifi: ath_attach: Switching rfkill capability off
Jan 1 00:00:20 AsusP user.info kernel: MadWifi: ath_attach: Switching per-packet transmit power control off
Jan 1 00:00:20 AsusP user.warn kernel: wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
Jan 1 00:00:20 AsusP user.warn kernel: wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
Jan 1 00:00:20 AsusP user.warn kernel: wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
Jan 1 00:00:20 AsusP user.warn kernel: wifi0: H/W encryption support: WEP AES AES_CCM TKIP
Jan 1 00:00:20 AsusP user.info kernel: wifi0: ath_announce: Use hw queue 1 for WME_AC_BE traffic
Jan 1 00:00:20 AsusP user.info kernel: wifi0: ath_announce: Use hw queue 0 for WME_AC_BK traffic
Jan 1 00:00:20 AsusP user.info kernel: wifi0: ath_announce: Use hw queue 2 for WME_AC_VI traffic
Jan 1 00:00:20 AsusP user.info kernel: wifi0: ath_announce: Use hw queue 3 for WME_AC_VO traffic
Jan 1 00:00:20 AsusP user.info kernel: wifi0: ath_announce: Use hw queue 8 for CAB traffic
Jan 1 00:00:20 AsusP user.info kernel: wifi0: ath_announce: Use hw queue 9 for beacons
Jan 1 00:00:20 AsusP user.info kernel: ath_pci: wifi0: Atheros 5212: mem=0x40000000, irq=6
Jan 1 00:00:20 AsusP user.info kernel: USB Universal Host Controller Interface driver v3.0
Jan 1 00:00:20 AsusP user.warn kernel: PCI: Enabling device 0000:00:03.0 (0000 -> 0001)
Jan 1 00:00:20 AsusP user.info kernel: PCI: Fixing up device 0000:00:03.0
Jan 1 00:00:20 AsusP user.info kernel: uhci_hcd 0000:00:03.0: UHCI Host Controller
Jan 1 00:00:20 AsusP user.info kernel: uhci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
Jan 1 00:00:20 AsusP user.info kernel: uhci_hcd 0000:00:03.0: irq 6, io base 0x00000100
Jan 1 00:00:20 AsusP user.info kernel: usb usb1: configuration #1 chosen from 1 choice
Jan 1 00:00:20 AsusP user.info kernel: hub 1-0:1.0: USB hub found
Jan 1 00:00:20 AsusP user.info kernel: hub 1-0:1.0: 2 ports detected
Jan 1 00:00:20 kernel: PCI: Enabling device 0000:00:03.1 (0000 -> 0001)
Jan 1 00:00:20 kernel: PCI: Fixing up device 0000:00:03.1
Jan 1 00:00:20 kernel: uhci_hcd 0000:00:03.1: UHCI Host Controller
Jan 1 00:00:20 kernel: uhci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
Jan 1 00:00:20 kernel: uhci_hcd 0000:00:03.1: irq 6, io base 0x00000120
Jan 1 00:00:20 kernel: usb usb2: configuration #1 chosen from 1 choice
Jan 1 00:00:20 kernel: hub 2-0:1.0: USB hub found
Jan 1 00:00:20 kernel: hub 2-0:1.0: 2 ports detected
Jan 1 00:00:21 AsusP user.warn kernel: PCI: Enabling device 0000:00:03.2 (0000 -> 0002)
Jan 1 00:00:21 AsusP user.info kernel: PCI: Fixing up device 0000:00:03.2
Jan 1 00:00:21 AsusP user.info kernel: ehci_hcd 0000:00:03.2: EHCI Host Controller
Jan 1 00:00:21 AsusP user.info kernel: ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
Jan 1 00:00:21 AsusP user.info kernel: ehci_hcd 0000:00:03.2: irq 6, io mem 0x40010000
Jan 1 00:00:21 kernel: usb 1-1: new full speed USB device using uhci_hcd and address 2
Jan 1 00:00:21 AsusP user.info kernel: ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
Jan 1 00:00:21 AsusP user.info kernel: usb usb3: configuration #1 chosen from 1 choice
Jan 1 00:00:21 AsusP user.info kernel: hub 3-0:1.0: USB hub found
Jan 1 00:00:21 AsusP user.info kernel: hub 3-0:1.0: 4 ports detected
Jan 1 00:00:22 kernel: usb 3-2: new high speed USB device using ehci_hcd and address 3
Jan 1 00:00:22 kernel: usb 3-2: configuration #1 chosen from 1 choice
Jan 1 00:00:22 kernel: usbcore: registered new interface driver snd-usb-audio
Jan 1 00:00:22 kernel: usb 1-1: new full speed USB device using uhci_hcd and address 3
Jan 1 00:00:22 AsusP user.info kernel: Initializing USB Mass Storage driver...
Jan 1 00:00:22 : Sending discover...
Jan 1 00:00:22 kernel: usb 1-1: configuration #1 chosen from 1 choice
Jan 1 00:00:22 AsusP user.info kernel: hub 1-1:1.0: USB hub found
Jan 1 00:00:22 kernel: hub 1-1:1.0: 5 ports detected
Jan 1 00:00:22 AsusP user.notice root: usb device is mass storage
Jan 1 00:00:22 AsusP user.notice root: waiting on usb drive 0 ...
Jan 1 00:00:22 AsusP user.info kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Jan 1 00:00:22 kernel: usb-storage: device found at 3
Jan 1 00:00:22 kernel: usb-storage: waiting for device to settle before scanning
Jan 1 00:00:23 AsusP user.info kernel: usb 1-1.2: new full speed USB device using uhci_hcd and address 4
Jan 1 00:00:23 kernel: usb 1-1.2: configuration #1 chosen from 1 choice
Jan 1 00:00:23 AsusP user.info kernel: usb 1-1.3: new full speed USB device using uhci_hcd and address 5
Jan 1 00:00:23 kernel: usb 1-1.3: configuration #1 chosen from 1 choice
Jan 1 00:00:24 AsusP user.info kernel: usb 1-1.5: new full speed USB device using uhci_hcd and address 6
Jan 1 00:00:24 AsusP user.notice root: waiting on usb drive 1 ...
Jan 1 00:00:24 kernel: usb 1-1.5: configuration #1 chosen from 1 choice
Jan 1 00:00:24 AsusP user.info kernel: usbcore: registered new interface driver usb-storage
Jan 1 00:00:24 AsusP user.info kernel: USB Mass Storage support registered.
Jan 1 00:00:24 kernel: Linux video capture interface: v2.00
Jan 1 00:00:24 AsusP user.info kernel: Bluetooth: Core ver 2.11
Jan 1 00:00:24 AsusP user.info kernel: NET: Registered protocol family 31
Jan 1 00:00:24 AsusP user.info kernel: Bluetooth: HCI device and connection manager initialized
Jan 1 00:00:24 AsusP user.info kernel: Bluetooth: HCI socket layer initialized
Jan 1 00:00:25 kernel: Bluetooth: L2CAP ver 2.8
Jan 1 00:00:25 kernel: Bluetooth: L2CAP socket layer initialized
Jan 1 00:00:25 AsusP user.notice root: waiting on usb drive 2 ...
Jan 1 00:00:25 AsusP user.info kernel: Bluetooth: SCO (Voice Link) ver 0.5
Jan 1 00:00:25 AsusP user.info kernel: Bluetooth: SCO socket layer initialized
Jan 1 00:00:25 kernel: Bluetooth: RFCOMM socket layer initialized
Jan 1 00:00:25 kernel: Bluetooth: RFCOMM TTY layer initialized
Jan 1 00:00:25 kernel: Bluetooth: RFCOMM ver 1.8
Jan 1 00:00:25 AsusP user.info kernel: Bluetooth: BNEP (Ethernet Emulation) ver 1.2
Jan 1 00:00:25 AsusP user.info kernel: Bluetooth: BNEP filters: protocol multicast
Jan 1 00:00:25 kernel: Bluetooth: HCI UART driver ver 2.2
Jan 1 00:00:25 kernel: Bluetooth: HCI H4 protocol initialized
Jan 1 00:00:25 kernel: Bluetooth: HCI BCSP protocol initialized
Jan 1 00:00:25 AsusP user.info kernel: Bluetooth: HCI USB driver ver 2.9
Jan 1 00:00:26 kernel: usbcore: registered new interface driver hci_usb
Jan 1 00:00:26 AsusP user.info kernel: /home/oconnor/Desktop/trunk/build_dir/linux-brcm47xx/spca5xx-le/spca_core.c: USB SPCA5XX camera found. Type Mustek gSmart Mini 3(SPCA504A)
Jan 1 00:00:26 kernel: usbcore: registered new interface driver spca5xx
Jan 1 00:00:26 kernel: /home/oconnor/Desktop/trunk/build_dir/linux-brcm47xx/spca5xx-le/spca_core.c: spca5xx driver 00.57.06LE registered
Jan 1 00:00:26 AsusP user.notice root: waiting on usb drive 3 ...
Jan 1 00:00:27 : 'wifi0' is disabled
Jan 1 00:00:27 : 'wifi0' is disabled
Jan 1 00:00:27 AsusP user.notice root: waiting on usb drive 4 ...
Jan 1 00:00:28 AsusP user.notice kernel: scsi 0:0:0:0: Direct-Access Verbatim Store'n'go U3 6.15 PQ: 0 ANSI: 0 CCS
Jan 1 00:00:28 kernel: sd 0:0:0:0: [sda] 1994751 512-byte hardware sectors (1021 MB)
Jan 1 00:00:28 AsusP user.notice kernel: sd 0:0:0:0: [sda] Write Protect is off
Jan 1 00:00:28 AsusP user.debug kernel: sd 0:0:0:0: [sda] Mode Sense: 45 00 00 08
Jan 1 00:00:28 AsusP user.err kernel: sd 0:0:0:0: [sda] Assuming drive cache: write through
Jan 1 00:00:28 kernel: sd 0:0:0:0: [sda] 1994751 512-byte hardware sectors (1021 MB)
Jan 1 00:00:28 AsusP user.notice kernel: sd 0:0:0:0: [sda] Write Protect is off
Jan 1 00:00:28 AsusP user.debug kernel: sd 0:0:0:0: [sda] Mode Sense: 45 00 00 08
Jan 1 00:00:28 AsusP user.err kernel: sd 0:0:0:0: [sda] Assuming drive cache: write through
Jan 1 00:00:28 AsusP user.info kernel: sda:
Jan 1 00:00:28 kernel: sda1
Jan 1 00:00:28 AsusP user.notice kernel: sd 0:0:0:0: [sda] Attached SCSI removable disk
Jan 1 00:00:28 AsusP user.debug kernel: usb-storage: device scan complete
Jan 1 00:00:28 AsusP user.notice root: waiting on usb drive 5 ...
Jan 1 00:00:29 : Sending select for 192.168.178.22...
Jan 1 00:00:29 : Lease of 192.168.178.22 obtained, lease time 864000
Jan 1 00:00:30 : adding router 192.168.178.1
Jan 1 00:00:30 : deleting old routes
Jan 1 00:00:30 : adding dns 192.168.178.1
Jan 1 00:00:31 : mounting /dev/sda1 on /mnt/usbdrive
Jan 1 00:00:31 AsusP user.warn kernel: EXT2-fs: sda1: couldn't mount because of unsupported optional features (4).
Jan 1 00:00:31 kernel: kjournald starting. Commit interval 5 seconds
Jan 1 00:00:31 AsusP user.warn kernel: EXT3-fs warning: mounting unchecked fs, running e2fsck is recommended
Feb 27 22:06:00 kernel: EXT3 FS on sda1, internal journal
Feb 27 22:06:00 kernel: EXT3-fs: recovery complete.
Feb 27 22:06:00 AsusP user.info kernel: EXT3-fs: mounted filesystem with ordered data mode.
Feb 27 22:06:00 AsusP authpriv.info dropbear[1017]: Running in background
Feb 27 22:06:03 AsusP authpriv.info dropbear[1045]: Child connection from 172.16.1.187:1194
Feb 27 22:06:03 : No configuration file specified.
Feb 27 22:06:03 : dbus-daemon [--version] [--session] [--system] [--config-file=FILE] [--print-address[=DESCRIPTOR]] [--print-pid[=DESCRIPTOR]] [--fork] [--nofork] [--introspect]
Feb 27 22:06:06 AsusP authpriv.notice dropbear[1045]: password auth succeeded for 'root' from 172.16.1.187:1194
Feb 27 22:06:07 AsusP daemon.info dnsmasq[1065]: started, version 2.40 cachesize 150
Feb 27 22:06:07 AsusP daemon.info dnsmasq[1065]: compile time options: IPv6 GNU-getopt ISC-leasefile no-DBus no-I18N TFTP
Feb 27 22:06:07 AsusP daemon.info dnsmasq[1065]: DHCP, IP range 172.16.1.100 -- 172.16.1.250, lease time 12h
Feb 27 22:06:07 AsusP daemon.info dnsmasq[1065]: using local addresses only for domain lan
Feb 27 22:06:07 AsusP daemon.info dnsmasq[1065]: reading /tmp/resolv.conf.auto
Feb 27 22:06:07 AsusP daemon.info dnsmasq[1065]: using nameserver 192.168.178.1#53
Feb 27 22:06:07 AsusP daemon.info dnsmasq[1065]: using local addresses only for domain lan
Feb 27 22:06:07 AsusP daemon.info dnsmasq[1065]: read /etc/hosts - 1 addresses
Feb 27 22:06:07 AsusP daemon.err dnsmasq[1065]: failed to read /etc/ethers:No such file or directory
Feb 27 22:06:09 : current locale is "C"
Feb 27 22:06:09 : setting filesystem charset to ISO-8859-1
Feb 27 22:06:09 : config parameter "db_file" not found
Feb 27 22:06:09 : config parameter "error_file" not found
Feb 27 22:06:14 : sysctl: error: 'net.ipv6.conf.all.forwarding' is an unknown keylsusb output
Bus 003 Device 003: ID 08ec:0016 M-Systems Flash Disk Pioneers
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 006: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode)
Bus 001 Device 005: ID 055f:c520 Mustek Systems, Inc. gSmart mini 3
Bus 001 Device 004: ID 1130:f211 Tenx Technology, Inc.
Bus 001 Device 003: ID 04cc:1122 Philips Semiconductors Hub
Bus 001 Device 001: ID 0000:0000Installed Ipkg packages
alsa-lib - 1.0.13-1 -
amule - 2.1.3-1 -
base-files-brcm47xx - 12-r10443 -
bemusedlinuxserver - r011-1 -
bluez-libs - 3.24-1 -
bluez-utils - 3.24-1 -
bridge - 1.0.6-1 -
busybox - 1.8.2-1 -
ctorrent - dnh3.2-1 -
dbus - 1.0.2-1 -
dctcs - 0.7.0-1 -
dnsmasq - 2.40-1 -
dropbear - 0.50-3 -
glib1 - 1.2.10-1 -
haserl - 0.8.0-2 -
hotplug2 - 0.9+r102-2 -
iptables - 1.3.8-2 -
kernel - 2.6.23.16-brcm47xx-1 -
kmod-bluetooth - 2.6.23.16-brcm47xx-1 -
kmod-diag - 2.6.23.16-brcm47xx-2 -
kmod-fs-ext2 - 2.6.23.16-brcm47xx-1 -
kmod-fs-ext3 - 2.6.23.16-brcm47xx-1 -
kmod-ipt-nathelper - 2.6.23.16-brcm47xx-1 -
kmod-madwifi - 2.6.23.16+r3314-brcm47xx-1 -
kmod-ppp - 2.6.23.16-brcm47xx-1 -
kmod-pppoe - 2.6.23.16-brcm47xx-1 -
kmod-scsi-core - 2.6.23.16-brcm47xx-1 -
kmod-sound-core - 2.6.23.16-brcm47xx-1 -
kmod-switch - 2.6.23.16-brcm47xx-1 -
kmod-usb-audio - 2.6.23.16-brcm47xx-1 -
kmod-usb-core - 2.6.23.16-brcm47xx-1 -
kmod-usb-storage - 2.6.23.16-brcm47xx-1 -
kmod-usb-uhci - 2.6.23.16-brcm47xx-1 -
kmod-usb2 - 2.6.23.16-brcm47xx-1 -
kmod-video-core - 2.6.23.16-brcm47xx-1 -
kmod-video-spca5xx-le - 2.6.23.16+1-brcm47xx-1 -
libexpat - 1.95.8-1 -
libflac - 1.1.2-1 -
libgcc - 4.1.2-12 -
libgd - 2.0.33-2 -
libid3tag - 0.15.1b-1 -
libjpeg - 6b-1 -
libmad - 0.15.1b-1 -
libncurses - 5.6-1 -
libopenssl - 0.9.8e-3 -
libpcap - 0.9.4-1 -
libpcre - 7.6-2 -
libpng - 1.2.8-1 -
libpthread - 0.9.29-12 -
libreadline - 5.1-1 -
libsqlite2 - 2.8.17-1 -
libsqlite3 - 3.4.2-1 -
libstdcpp - 4.1.2-12 -
libuci - 0.2.5-1 -
libusb - 0.1.12-1 -
libvorbisidec - 1.0.2+svn14261-1 -
libwxbase - 2.6.4-1 -
libxml2 - 2.6.20-1 -
lighttpd - 1.4.18-2 -
lighttpd-mod-cgi - 1.4.18-2 -
mpd - 0.13.1-1 -
mtd - 6 -
ntpclient - 2003_194-6 -
openssh-sftp-server - 4.7p1-1 -
php5 - 5.2.5-1 -
php5-cgi - 5.2.5-1 -
php5-mod-gd - 5.2.5-1 -
php5-mod-openssl - 5.2.5-1 -
php5-mod-pcre - 5.2.5-1 -
php5-mod-session - 5.2.5-1 -
php5-mod-sqlite - 5.2.5-1 -
php5-mod-xml - 5.2.5-1 -
ppp - 2.4.3-9 -
ppp-mod-pppoe - 2.4.3-9 -
samba-common - 2.0.10-4 -
samba-server - 2.0.10-4 -
sqlite2-cli - 2.8.17-1 -
sqlite3-cli - 3.4.2-1 -
tcpdump - 3.9.8-1 -
uci - 0.2.5-1 -
uclibc - 0.9.29-12 -
uclibcxx - 0.2.2-1 -
udevtrigger - 106-1 -
usbutils - 0.72-1 -
webif - 0.3-10 -
wireless-tools - 29-2 -
wol - 0.7.1-2 -
zlib - 1.2.3-5 -
Done.lsmod output
Module Size Used by Tainted: P
spca5xx 82304 0
hci_usb 12320 0
hci_uart 14752 0
bnep 10528 0
rfcomm 40384 0
sco 7792 0
l2cap 16944 4 bnep,rfcomm
bluetooth 53456 6 hci_usb,hci_uart,bnep,rfcomm,sco,l2cap
videodev 23104 1 spca5xx
compat_ioctl32 448 0
v4l1_compat 11280 1 videodev
v4l2_common 12608 1 videodev
usb_storage 28032 1
snd_usb_audio 57216 0
snd_usb_lib 11936 1 snd_usb_audio
ehci_hcd 28880 0
uhci_hcd 19920 0
ath_pci 126224 0
wlan_xauth 480 0
wlan_wep 4000 0
wlan_tkip 9664 0
wlan_ccmp 5440 0
wlan_acl 1920 0
ath_rate_minstrel 8256 1
ath_hal 271168 3 ath_pci,ath_rate_minstrel
wlan_scan_sta 8768 0
wlan_scan_ap 6656 0
wlan 152624 10 ath_pci,wlan_xauth,wlan_wep,wlan_tkip,wlan_ccmp,wlan_acl,ath_rate_minstrel,wlan_scan_sta,wlan_scan_ap
sd_mod 18512 2
nf_nat_tftp 480 0
nf_conntrack_tftp 2480 1 nf_nat_tftp
nf_nat_irc 960 0
nf_conntrack_irc 2832 1 nf_nat_irc
nf_nat_ftp 1472 0
nf_conntrack_ftp 5152 1 nf_nat_ftp
snd_pcm_oss 40064 0
snd_mixer_oss 13728 1 snd_pcm_oss
snd_pcm 57376 2 snd_usb_audio,snd_pcm_oss
snd_timer 16336 1 snd_pcm
snd_rawmidi 16288 1 snd_usb_lib
snd_seq_device 4112 1 snd_rawmidi
snd_hwdep 4784 1 snd_usb_audio
snd_page_alloc 5168 1 snd_pcm
snd 35344 8 snd_usb_audio,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_rawmidi,snd_seq_device,snd_hwdep
soundcore 3664 1 snd
ppp_async 9856 0
ppp_generic 20192 1 ppp_async
slhc 5376 1 ppp_generic
crc_ccitt 1024 1 ppp_async
ext3 98064 1
jbd 55408 1 ext3
ext2 40336 0
usbcore 106576 8 spca5xx,hci_usb,usb_storage,snd_usb_audio,snd_usb_lib,ehci_hcd,uhci_hcd
scsi_mod 72256 2 usb_storage,sd_mod
switch_robo 4016 0
switch_core 5056 1 switch_robo
diag 8400 0
, also the Bluetooth. I think I missed something to install but I don't know what.
this means, bemused connect to mpd to get and send information. so you need a working mpd. whats the error about mpd? check all path references in mpd.conf (verify that those path exist), check check sound config.