Dear Friends,
I have implemented OpenWRT on IXP425 based Board which has Texas Instruments PCI1520 PC card Cardbus .
Now i am going to put Planex`s Wireless LAN card which has relatek RT2860 chip.
But after enableing PC Card bus in kernel , card insert event is not at all occuring,
I am attaching lspci -vv view below and kernel boot log,
Any help would be greatly appriciated,
root@OpenWrt:/# lspci -vv
00:14.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 50) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 22, Cache Line Size 08
Interrupt: pin A routed to IRQ 7
Region 4: I/O ports at 1000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:14.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 50) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 22, Cache Line Size 08
Interrupt: pin B routed to IRQ 7
Region 4: I/O ports at 1020 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:14.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 51) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) Unknown device 1234
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 22, Cache Line Size 08
Interrupt: pin C routed to IRQ 7
Region 0: Memory at 49002000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:15.0 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus Controller (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size 08
Interrupt: pin A routed to IRQ 6
Region 0: Memory at 49000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=04, sec-latency=176
Memory window 0: 48000000-483ff000 (prefetchable)
Memory window 1: 48400000-487ff000
I/O window 0: 00000000-000000ff
I/O window 1: 00000400-000004ff
BridgeCtl: Parity+ SERR- ISA- VGA- MAbort+ >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:15.1 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus Controller (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size 08
Interrupt: pin A routed to IRQ 6
Region 0: Memory at 49001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=05, subordinate=08, sec-latency=176
Memory window 0: 48800000-48bff000 (prefetchable)
Memory window 1: 48c00000-48fff000
I/O window 0: 00000800-000008ff
I/O window 1: 00000c00-00000cff
BridgeCtl: Parity+ SERR- ISA- VGA- MAbort+ >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
root@OpenWrt:#
RedBoot> exec
Using base address 0x00029c00 and length 0x00103a54
Uncompressing Linux........................................................................ done, booting the kernel.
Linux version 2.6.21.6 (root@dev) (gcc version 4.1.2) #62 Tue Jul 8 17:07:30 JST 2008
CPU: XScale-IXP42x Family [690541f1] revision 1 (ARMv5TE), cr=000039ff
Machine: ADI Engineering Pronghorn Metro
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Built 1 zonelists. Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 init=/etc/preinit
PID hash table entries: 128 (order: 7, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 32MB = 32MB total
Memory: 30164KB available (1940K code, 266K data, 76K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
IXP4xx: Using 16MiB expansion bus window size
PCI: IXP4xx is host
PCI: IXP4xx Using indirect access for memory space
PCI: bus0: Fast back to back transfers disabled
dmabounce: registered device 0000:00:14.0 on pci bus
dmabounce: registered device 0000:00:14.1 on pci bus
dmabounce: registered device 0000:00:14.2 on pci bus
dmabounce: registered device 0000:00:15.0 on pci bus
dmabounce: registered device 0000:00:15.1 on pci bus
PCI: allocate information for debug mem resource #9:400000@400000 for 0000:00:15.0 ret=[-12]
PCI: allocate information for debug mem resource #10:400000@400000 for 0000:00:15.0 ret=[0]
PCI: allocate information for debug mem resource #9:400000@400000 for 0000:00:15.1 ret=[-12]
PCI: allocate information for debug mem resource #10:400000@400000 for 0000:00:15.1 ret=[0]
PCI: allocate information for debug mem resource #0:1000@1000 for 0000:00:15.0 ret=[0]
PCI: allocate information for debug mem resource #0:1000@1000 for 0000:00:15.1 ret=[0]
PCI: allocate information for debug mem resource #0:100@100 for 0000:00:14.2 ret=[0]
PCI: allocate information for debug I/O resource #7:100@100 for 0000:00:15.0 ret=[0]
PCI: allocate information for debug I/O resource #8:100@100 for 0000:00:15.0 ret=[0]
PCI: allocate information for debug I/O resource #7:100@100 for 0000:00:15.1 ret=[0]
PCI: allocate information for debug I/O resource #8:100@100 for 0000:00:15.1 ret=[0]
PCI: allocate information for debug I/O resource #4:20@20 for 0000:00:14.0 ret=[0]
PCI: allocate information for debug I/O resource #4:20@20 for 0000:00:14.1 ret=[0]
PCI: Bus 1, cardbus bridge: 0000:00:15.0
IO window: 00000000-000000ff
IO window: 00000400-000004ff
PREFETCH window: 48000000-483fffff
MEM window: 48400000-487fffff
PCI: Bus 5, cardbus bridge: 0000:00:15.1
IO window: 00000800-000008ff
IO window: 00000c00-00000cff
PREFETCH window: 48800000-48bfffff
MEM window: 48c00000-48ffffff
pci 0000:00:15.0: Error creating sysfs bridge symlink, continuing...
pci 0000:00:15.1: Error creating sysfs bridge symlink, continuing...
Time: OSTS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NetWinder Floating Point Emulator V0.97 (double precision)
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered (default)
IXP4xx Watchdog Timer: heartbeat 60 sec
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xc8001000 (irq = 13) is a XScale
IXP4XX Q Manager 0.2.1 initialized.
IXP4XX NPE driver Version 0.3.0 initialized
ixp4xx_crypto 0.0.1 registered successfully
IXP4XX-Flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Searching for RedBoot partition table in IXP4XX-Flash.0 at offset 0xfe0000
6 RedBoot partitions found on MTD device IXP4XX-Flash.0
Creating 6 MTD partitions on "IXP4XX-Flash.0":
0x00000000-0x00080000 : "RedBoot"
npe: searching for firmware...
npe: found at 0x120b8, unknown/NPE-A func: 03, rev: a.8, size: 1074718860, id: 5003baa8
npe: found at 0x3f2ac, IXP465/NPE-A func: 81, rev: 2.0, size: 12848, id: 10810200
npe: found at 0x424dc, IXP425/NPE-B func: 01, rev: 2.0, size: 12848, id: 01010200
Image loaded to NPE-B Func:1, Rel: 2:0, Status: 82c00000
npe: found at 0x4570c, IXP425/NPE-C func: 01, rev: 2.0, size: 12848, id: 02010200
Image loaded to NPE-C Func:1, Rel: 2:0, Status: 80c00000
0x00080000-0x001a0000 : "kernel"
0x001a0000-0x00fc0000 : "rootfs"
0x00380000-0x00fc0000 : "rootfs_data"
0x00fc0000-0x00fe0000 : "unallocated"
0x00fe0000-0x00fff000 : "FIS directory"
0x00fff000-0x01000000 : "RedBoot config"
PCI: enabling device 0000:00:15.0 (0140 -> 0143)
Yenta: CardBus bridge found at 0000:00:15.0 [0000:0000]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:15.0, mfunc 0x00001002, devctl 0x64
Yenta: ISA IRQ mask 0x0000, PCI irq 6
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x0 - 0xffff
pcmcia: parent PCI bridge Memory window: 0x48000000 - 0x4fffffff
PCI: enabling device 0000:00:15.1 (0140 -> 0143)
Yenta: CardBus bridge found at 0000:00:15.1 [0000:0000]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:15.1, mfunc 0x00001002, devctl 0x64
Yenta: ISA IRQ mask 0x0000, PCI irq 6
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x0 - 0xffff
pcmcia: parent PCI bridge Memory window: 0x48000000 - 0x4fffffff
i2c /dev entries driver
nf_conntrack version 0.5.0 (256 buckets, 2048 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP westwood registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
XScale DSP coprocessor detected.
ixp4xx_mac driver 0.3.1: eth0 on NPE-B with PHY[0] initialized
ixp4xx_mac driver 0.3.1: eth1 on NPE-C with PHY[1] initialized
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
VFS: Mounted root (squashfs filesystem) readonly.
Freeing init memory: 76K
Warning: unable to open an initial console.
- preinit -
switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
- init -
init started: BusyBox v1.4.2 (2008-07-08 10:21:16 JST) multi-call binary
Please press Enter to activate this console. :
root@OpenWrt:/# cat /proc/iomem
00000000-01ffffff : System RAM
00000000-00000000 : pata_ixp4xx_cf.0
00000000-00000000 : pata_ixp4xx_cf.0
0001b000-001fffff : Kernel text
00200000-00242a6b : Kernel data
48000000-4fffffff : PCI Memory Space
48000000-483fffff : PCI CardBus #01
48400000-487fffff : PCI CardBus #01
48800000-48bfffff : PCI CardBus #05
48c00000-48ffffff : PCI CardBus #05
49000000-49000fff : 0000:00:15.0
49000000-49000fff : yenta_socket
49001000-49001fff : 0000:00:15.1
49001000-49001fff : yenta_socket
49002000-490020ff : 0000:00:14.2
49002000-490020ff : ehci_hcd
50000000-50ffffff : IXP4XX-Flash.0
50000000-50ffffff : IXP4XXFlash
60000000-60003fff : ixp4xx_qmgr.0
60000000-60003fff : ixp_qmgr
c8001000-c8001fff : serial8250.0
c8001000-c800101f : serial
c8006000-c8006fff : ixp4xx_npe.0
c8006000-c8006fff : NPE-A
c8007000-c8007fff : ixp4xx_npe.1
c8007000-c8007fff : NPE-B
c8008000-c8008fff : ixp4xx_npe.2
c8008000-c8008fff : NPE-C
c8009000-c80091ff : ixp4xx_mac.0
c8009000-c80091ff : ixp4xx_mac
c800a000-c800a1ff : ixp4xx_mac.1
c800a000-c800a1ff : ixp4xx_mac
c800b000-c800bfff : pxa2xx-udc
root@OpenWrt:/# cat /proc/ioports
00000000-0000ffff : PCI I/O Space
00000000-000000ff : PCI CardBus #01
00000400-000004ff : PCI CardBus #01
00000800-000008ff : PCI CardBus #05
00000c00-00000cff : PCI CardBus #05
00001000-0000101f : 0000:00:14.0
00001000-0000101f : uhci_hcd
00001020-0000103f : 0000:00:14.1
00001020-0000103f : uhci_hcd
root@OpenWrt:/# cat proc/interrupts
CPU0
3: 13944 IXP4xx qmgr
5: 1057005 IXP4xx IXP4xx Timer Tick
6: 2 IXP4xx yenta, yenta
7: 0 IXP4xx uhci_hcd:usb1, uhci_hcd:usb2, ehci_hcd:usb3
13: 2856 IXP4xx serial
Err: 0
root@OpenWrt:/#
and kernel boot log,
RedBoot> fis load kernel
RedBoot> exec
Using base address 0x00029c00 and length 0x00103a54
Uncompressing Linux........................................................................ done, booting the kernel.
Linux version 2.6.21.6 (root@dev) (gcc version 4.1.2) #62 Tue Jul 8 17:07:30 JST 2008
CPU: XScale-IXP42x Family [690541f1] revision 1 (ARMv5TE), cr=000039ff
Machine: ADI Engineering Pronghorn Metro
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Built 1 zonelists. Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 init=/etc/preinit
PID hash table entries: 128 (order: 7, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 32MB = 32MB total
Memory: 30164KB available (1940K code, 266K data, 76K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
IXP4xx: Using 16MiB expansion bus window size
PCI: IXP4xx is host
PCI: IXP4xx Using indirect access for memory space
PCI: bus0: Fast back to back transfers disabled
dmabounce: registered device 0000:00:14.0 on pci bus
dmabounce: registered device 0000:00:14.1 on pci bus
dmabounce: registered device 0000:00:14.2 on pci bus
dmabounce: registered device 0000:00:15.0 on pci bus
dmabounce: registered device 0000:00:15.1 on pci bus
PCI: allocate information for debug mem resource #9:400000@400000 for 0000:00:15.0 ret=[-12]
PCI: allocate information for debug mem resource #10:400000@400000 for 0000:00:15.0 ret=[0]
PCI: allocate information for debug mem resource #9:400000@400000 for 0000:00:15.1 ret=[-12]
PCI: allocate information for debug mem resource #10:400000@400000 for 0000:00:15.1 ret=[0]
PCI: allocate information for debug mem resource #0:1000@1000 for 0000:00:15.0 ret=[0]
PCI: allocate information for debug mem resource #0:1000@1000 for 0000:00:15.1 ret=[0]
PCI: allocate information for debug mem resource #0:100@100 for 0000:00:14.2 ret=[0]
PCI: allocate information for debug I/O resource #7:100@100 for 0000:00:15.0 ret=[0]
PCI: allocate information for debug I/O resource #8:100@100 for 0000:00:15.0 ret=[0]
PCI: allocate information for debug I/O resource #7:100@100 for 0000:00:15.1 ret=[0]
PCI: allocate information for debug I/O resource #8:100@100 for 0000:00:15.1 ret=[0]
PCI: allocate information for debug I/O resource #4:20@20 for 0000:00:14.0 ret=[0]
PCI: allocate information for debug I/O resource #4:20@20 for 0000:00:14.1 ret=[0]
PCI: Bus 1, cardbus bridge: 0000:00:15.0
IO window: 00000000-000000ff
IO window: 00000400-000004ff
PREFETCH window: 48000000-483fffff
MEM window: 48400000-487fffff
PCI: Bus 5, cardbus bridge: 0000:00:15.1
IO window: 00000800-000008ff
IO window: 00000c00-00000cff
PREFETCH window: 48800000-48bfffff
MEM window: 48c00000-48ffffff
pci 0000:00:15.0: Error creating sysfs bridge symlink, continuing...
pci 0000:00:15.1: Error creating sysfs bridge symlink, continuing...
Time: OSTS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NetWinder Floating Point Emulator V0.97 (double precision)
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered (default)
IXP4xx Watchdog Timer: heartbeat 60 sec
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xc8001000 (irq = 13) is a XScale
IXP4XX Q Manager 0.2.1 initialized.
IXP4XX NPE driver Version 0.3.0 initialized
ixp4xx_crypto 0.0.1 registered successfully
IXP4XX-Flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Searching for RedBoot partition table in IXP4XX-Flash.0 at offset 0xfe0000
6 RedBoot partitions found on MTD device IXP4XX-Flash.0
Creating 6 MTD partitions on "IXP4XX-Flash.0":
0x00000000-0x00080000 : "RedBoot"
npe: searching for firmware...
npe: found at 0x120b8, unknown/NPE-A func: 03, rev: a.8, size: 1074718860, id: 5003baa8
npe: found at 0x3f2ac, IXP465/NPE-A func: 81, rev: 2.0, size: 12848, id: 10810200
npe: found at 0x424dc, IXP425/NPE-B func: 01, rev: 2.0, size: 12848, id: 01010200
Image loaded to NPE-B Func:1, Rel: 2:0, Status: 82c00000
npe: found at 0x4570c, IXP425/NPE-C func: 01, rev: 2.0, size: 12848, id: 02010200
Image loaded to NPE-C Func:1, Rel: 2:0, Status: 80c00000
0x00080000-0x001a0000 : "kernel"
0x001a0000-0x00fc0000 : "rootfs"
0x00380000-0x00fc0000 : "rootfs_data"
0x00fc0000-0x00fe0000 : "unallocated"
0x00fe0000-0x00fff000 : "FIS directory"
0x00fff000-0x01000000 : "RedBoot config"
PCI: enabling device 0000:00:15.0 (0140 -> 0143)
Yenta: CardBus bridge found at 0000:00:15.0 [0000:0000]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:15.0, mfunc 0x00001002, devctl 0x64
Yenta: ISA IRQ mask 0x0000, PCI irq 6
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x0 - 0xffff
pcmcia: parent PCI bridge Memory window: 0x48000000 - 0x4fffffff
PCI: enabling device 0000:00:15.1 (0140 -> 0143)
Yenta: CardBus bridge found at 0000:00:15.1 [0000:0000]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:15.1, mfunc 0x00001002, devctl 0x64
Yenta: ISA IRQ mask 0x0000, PCI irq 6
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x0 - 0xffff
pcmcia: parent PCI bridge Memory window: 0x48000000 - 0x4fffffff
i2c /dev entries driver
nf_conntrack version 0.5.0 (256 buckets, 2048 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP westwood registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
XScale DSP coprocessor detected.
ixp4xx_mac driver 0.3.1: eth0 on NPE-B with PHY[0] initialized
ixp4xx_mac driver 0.3.1: eth1 on NPE-C with PHY[1] initialized
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
VFS: Mounted root (squashfs filesystem) readonly.
Freeing init memory: 76K
Warning: unable to open an initial console.
- preinit -
switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
- init -
init started: BusyBox v1.4.2 (2008-07-08 10:21:16 JST) multi-call binary
Please press Enter to activate this console. : syslogd has already been started.
: klogd has already been started.