OpenWrt Forum Archive

Topic: New Broadcom BCM63xx codebase with GPL'd Ethernet and USB support

The content of this topic has been archived between 8 Feb 2018 and 7 May 2018. Unfortunately there are posts – most likely complete pages – missing.

no luck with Sagem Fast 2404 (f@st2404) .. doesn't find block device  sad (tried both snapshots and svn from trunk )...

Sagem CFE version: 3.13.5                          
Build Date: Mon May 14 17:56:09 CST 2007 (shenmc@svr1.sagemharbournetworks.com)
Copyright (C) 2005-2006 Sagem communication.

Boot Address 0xbfc00000

Initializing Arena.
Initializing Devices.
Parallel flash device: name SST39VF3201, id 0x235b, size 4096KB
Enter readNvramData(CFE)
Enter kerSysNvRamGet(CFE)
kerSysNvRamGet(CFE) Mac address:00:19:4b:b4:dd:aa, BoardId=F@ST2404  
Enter readNvramData(CFE)                                                        
Enter kerSysNvRamGet(CFE)                                                       
kerSysNvRamGet(CFE) Mac address:00:19:4b:b4:dd:aa, BoardId=F@ST2404             
Enter readNvramData(CFE)                                                        
Enter kerSysNvRamGet(CFE)                                                       
kerSysNvRamGet(CFE) Mac address:00:19:4b:b4:dd:aa, BoardId=F@ST2404             
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz                               
Total memory: 16777216 bytes (16MB)                                             
                                                                                
Total memory used by CFE:  0x80401000 - 0x80528470 (1209456)                    
Initialized Data:          0x8041EAE0 - 0x80421AB0 (12240)                      
BSS Area:                  0x80421AB0 - 0x80426470 (18880)                      
Local Heap:                0x80426470 - 0x80526470 (1048576)                    
Stack Area:                0x80526470 - 0x80528470 (8192)                       
Text (code) segment:       0x80401000 - 0x8041EAD8 (121560)                     
Boot area (physical):      0x00529000 - 0x00569000                              
Relocation Factor:         I:00000000 - D:00000000                              
                                                                                
Enter readNvramData(CFE)                                                        
Enter kerSysNvRamGet(CFE)                                                       
kerSysNvRamGet(CFE) Mac address:00:19:4b:b4:dd:aa, BoardId=F@ST2404             
Enter readNvramData(CFE)                                                        
Enter kerSysNvRamGet(CFE)                                                       
kerSysNvRamGet(CFE) Mac address:00:19:4b:b4:dd:aa, BoardId=F@ST2404             
Board IP address                  : 192.168.2.1                                 
Host IP address                   : 182.168.2.34                                
Gateway IP address                :                                             
Run from flash/host (f/h)         : f                                           
Default host run file name        : vmlinux                                     
Default host flash file name      : bcm963xx_fs_kernel                          
Boot delay (0-9 seconds)          : 2                                           
Board Id Name                     : F@ST2404                                    
Psi size in KB                    : 24                                          
Number of MAC Addresses (1-32)    : 11                                          
Base MAC Address                  : 00:19:4b:b4:dd:aa                           
Ethernet PHY Type                 : Internal                                    
Memory size in MB                 : 16                                          
CMT Thread Number                 : 0                                           
Customer Name                     :SAGM(default)                                
                                                                                
*** Press any key to stop auto run (2 seconds) ***                              
Auto run second count down: 0                                                   
Code Address: 0x80010000, Entry Address: 0x80010000                             
Decompression OK!                                                               
Entry at 0x80010000                                                             
Closing network.                                                                
Starting program at 0x80010000                                                  
Linux version 2.6.30.9 (paqutio@BOX) (gcc version 4.3.3 (GCC) ) #1 Sun Nov 9
Detected Broadcom 0x6348 CPU revision b0                                        
CPU frequency is 256000000 Hz                                                   
16MB of RAM installed                                                           
registering 37 GPIOs                                                            
board_bcm963xx: CFE version: 0.51.46-49.51                                      
console [early0] enabled                                                        
CPU revision is: 00029107 (Broadcom BCM6348)                                    
board_bcm963xx: board name: F@ST2404                                            
Determined physical RAM map:                                                    
 memory: 01000000 @ 00000000 (usable)                                           
Initrd not found or empty - disabling initrd                                    
Zone PFN ranges:                                                                
  Normal   0x00000000 -> 0x00001000                                             
Movable zone start PFN for each node                                            
early_node_map[1] active PFN ranges                                             
    0: 0x00000000 -> 0x00001000                                                 
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 4064      
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd con0
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.                 
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes              
NR_IRQS:128                                                                     
PID hash table entries: 64 (order: 6, 256 bytes)                                
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)                    
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)                     
Memory: 13264k/16384k available (2072k kernel code, 3120k reserved, 429k data, )
Calibrating delay loop... 254.97 BogoMIPS (lpj=509952)                          
Mount-cache hash table entries: 512                                             
net_namespace: 532 bytes                                                        
NET: Registered protocol family 16                                              
registering PCI controller with io_map_base unset                               
bio: create slab <bio-0> at 0                                                   
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)                                
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0                  
NET: Registered protocol family 2                                               
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)                  
TCP established hash table entries: 512 (order: 0, 4096 bytes)                  
TCP bind hash table entries: 512 (order: -1, 2048 bytes)                        
TCP: Hash tables configured (established 512 bind 512)                          
TCP reno registered                                                             
NET: Registered protocol family 1                                               
audit: initializing netlink socket (disabled)                                   
type=2000 audit(0.324:1): initialized                                           
squashfs: version 4.0 (2009/01/31) Phillip Lougher                              
Registering mini_fo version $Id$                                                
JFFS2 version 2.2. (NAND) (SUMMARY)  ?© 2001-2006 Red Hat, Inc.                 
msgmni has been set to 25                                                       
alg: No test for lzma (lzma-generic)                                            
alg: No test for stdrng (krng)                                                  
io scheduler noop registered                                                    
io scheduler deadline registered (default)                                      
gpiodev: gpio device registered with major 254                                  
gpiodev: gpio platform device registered with access mask FFFFFFFF              
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart           
console handover: boot [early0] -> real [ttyS0]                                 
bcm63xx_enet MII bus: probed                                                    
bcm963xx_flash: 0x00400000 at 0x1fc00000                                        
bcm963xx_flash: Failed to probe using CFI                                       
bcm963xx-flash: probe of bcm963xx-flash.0 failed with error -5                  
bcm63xx_wdt started, timer margin: 30 sec                                       
Registered led device: <NULL>                                                   
leds-gpio: probe of leds-gpio.0 failed with error -16                           
TCP westwood registered                                                         
NET: Registered protocol family 17                                              
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>                   
All bugs added by David S. Miller <davem@redhat.com>                            
VFS: Cannot open root device "mtdblock2" or unknown-block(0,0)                  
Please append a correct "root=" boot option; here are the available partitions: 
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

(Last edited by DeerHunter on 1 Nov 2009, 23:48)

helloo ppl,
  first sorry for poor english ;-)
I use openwrt for bmc63xx board, flash image via CFE and web both work, but after board restart in serial console show me ..

You need upgrade your run time image through CFE TFTP or CFE web......

boot 1 found no image

** Image information not found. **

here dmesg from router

Linux version 2.6.30.9 (test@r2) (gcc version 4.3.3 (GCC) ) #1 Wed Nov 11 04:43:44 EST 2009
Detected Broadcom 0x6348 CPU revision b0
CPU frequency is 240000000 Hz
16MB of RAM installed
registering 37 GPIOs
board_bcm963xx: CFE version: 1.0.37-6.8
console [early0] enabled
CPU revision is: 00029107 (Broadcom BCM6348)
board_bcm963xx: board name: board_bcm963xx
Determined physical RAM map:
 memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00001000
On node 0 totalpages: 4096
free_area_init_node: node 0, pgdat 8027f5f0, node_mem_map 802e7000
  Normal zone: 32 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 4064 pages, LIFO batch:0
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
NR_IRQS:128
PID hash table entries: 64 (order: 6, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 13268k/16384k available (2073k kernel code, 3116k reserved, 428k data, 132k init, 0k highmem)
Calibrating delay loop... 239.10 BogoMIPS (lpj=478208)
Mount-cache hash table entries: 512
net_namespace: 532 bytes
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
pci 0000:00:01.0: reg 10 32bit mmio: [0x000000-0x001fff]
Switched to high resolution mode on CPU 0
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:01.0 to 64
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(0.352:1): initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
msgmni has been set to 25
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
console handover: boot [early0] -> real [ttyS0]
bcm63xx_enet MII bus: probed
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6, board type board_bcm963xx, and tagid bc221.
bcm963xx_flash: Partition 0 is CFE offset 0 and length 10000
bcm963xx_flash: Partition 1 is kernel offset 10100 and length dff00
bcm963xx_flash: Partition 2 is rootfs offset f0000 and length 300000
bcm963xx_flash: Partition 3 is nvram offset 3f0000 and length 10000
bcm963xx_flash: Partition 4 is linux offset 10000 and length 3e0000
bcm963xx_flash: Spare partition is 330000 offset and length c0000
Creating 5 MTD partitions on "bcm963xx":
0x000000000000-0x000000010000 : "CFE"
0x000000010100-0x0000000f0000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x0000000f0000-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
split_squashfs: no squashfs found in "bcm963xx"
0x0000003f0000-0x000000400000 : "nvram"
0x000000010000-0x0000003f0000 : "linux"
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: <NULL>
leds-gpio: probe of leds-gpio.0 failed with error -16
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
jffs2_scan_eraseblock(): End of filesystem marker found at 0x230000
jffs2_build_filesystem(): unlocking the mtd device... done.
jffs2_build_filesystem(): erasing all blocks after the end marker... done.
VFS: Mounted root (jffs2 filesystem) readonly on device 31:2.
Freeing unused kernel memory: 132k freed
Please be patient, while OpenWrt loads ...
bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (1)]
eth1: link forced UP - 100/full - flow control off/off
device eth1 entered promiscuous mode
br-lan: port 1(eth1) entering forwarding state
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
    (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
    (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
    (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
    (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
    (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
roboswitch: Probing device eth0: Failed to enable switch
roboswitch: Probing device eth1: Failed to enable switch
roboswitch: Probing device eth2: No such device
roboswitch: Probing device eth3: No such device
b43-phy0: Broadcom 4318 WLAN found (core revision 9)
phy0: Selected rate control algorithm 'minstrel'
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (256 buckets, 1024 max)

If anyone can help I would be very grateful thanks in advance.

megalomania,
upgrading CFE is very dangerous , you can brick your router..
Does the firmware work for you ?

(Last edited by DeerHunter on 12 Nov 2009, 16:59)

yes, firmware from dynalink work.

(Last edited by megalomania on 12 Nov 2009, 19:42)

Hello again, can anyone tell me if this is normal?

00000000  36 00 00 00 42 72 6f 61  64 63 6f 6d 20 43 6f 72  |6...Broadcom Cor|
00000010  70 6f 72 61 74 69 6f 00  76 65 72 2e 20 32 2e 30  |poratio.ver. 2.0|
00000020  00 00 00 00 00 00 36 33  34 38 00 00 52 54 41 31  |......6348..RTA  1|
00000030  30 32 35 57 5f 31 36 00  00 00 00 00 31 00 33 32  |0 25 W_16.....1.32|
00000040  37 36 35 34 38 00 00 00  30 00 00 00 00 00 00 00  |76548...0.......|
00000050  00 00 00 00 30 00 00 00  00 00 00 00 00 00 33 32  |....0.........32|
00000060  31 37 30 39 36 39 36 30  00 00 32 33 35 39 33 30  |17096960..235930|
00000070  30 00 00 00 33 32 31 37  30 39 36 39 36 30 00 00  |0...3217096960..|
00000080  39 31 37 32 34 38 00 00  00 00 00 00 00 00 00 00  |917248..........|
00000090  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00  |................|
000000a0  00 00 00 00 62 63 32 32  31 00 33 32 31 38 30 31  |....bc221.321801|
000000b0  34 32 30 38 00 00 32 33  35 39 32 39 36 00 00 00  |4208..2359296...|
000000c0

I talk about CFE starting address and CFE (boot loader) size the both 0.

Hello, guys. Im newbie to wonderful world of OpenWRT, but I must say - thanks! Its very nice to see how it works.

Now, some success story - after checking out bleeding edge r18445 Kamikaze I built it, and guess so - it doesnt work, cause board "D-4P-W" is absent from board_63xx.c file (though I saw snapshots with filename like that, but they didnt work for me). So, with little patching by outlines of post #58, OpenWRT successifully started on my hardware (D-Link DSL 2640U HW ver B2). Now time for some config and testing. DSL dont work, of course.

(sorry for my crappy English)

After a lot of compile and test i found the problem, after flash the router with openwrt-RTA1025W_16-squashfs-btrta-cfe.bin the last script who run it's  /sbin/firstboot when disable this script router work, if this script /sbin/firstboot run after reboot router don't start.Hints ?

Hi i also have a tp-link 8840.
While 2mb of flash isn't much, if it is enough to have dropbear + basic config + ppp (pppoe/pppoa) that would be fine.

I would prefer not to stay on the outdated kernel tplink provides or suffer from a few minor software glitches (random rebooting at times).

It is a 96338L-2M-8M, with  Bootloader (CFE) Version:      1.0.37-6.5.

Is 2mb really too "small" ? ......

megalomania, maybe you should read the wiki: /sbin/firstboot  ... i hope it's helpful.

d-b,  2M is  smal.. but you could build some firmware, yes..

hello all, this is the boot-log of my router (siemens cl-110), it is base on a brc6338 chip, does anyone now if I can flash it with an image from the 6338 snapshots?
thanks in advance!


CFE version 1.0.37-6.8.5 for BCM96338 (32bit,SP,BE)
Build Date: Wed Apr 11 16:56:28 CST 2007 (michaelc)

Boot Address 0xbfc00000

Flash Config: CS0(1fc00009,17),Base(bfc00000),Size(4MB)
Ethernet Single Port
100 MB Full-Duplex (auto-neg)
bootf 78/ff  boot from bank 0

Board IP address                  : 10.0.1.150 
Host IP address                   : 10.0.1.100 
Gateway IP address                : 10.0.1.1 
Run from flash/host (f/h)         : f 
Default host run file name        : vmlinux 
Default host flash file name      : bcmModelName_fs_kernel 
Boot delay (0-9 seconds)          : 2 
Board Id Name                     : RTA1320_16M 
Psi size in KB                    : 24
Number of MAC Addresses (1-32)    : 3 
Ethernet MAC Address              : 00:1b:9e:26:79:45 
Serial Number                     : CS1621Z131A176007734 
Memory size in MB                 : 16
CMT Thread Number                 : 0

==== Press space key to stop auto run (2 seconds) ====
Auto run second count down(before hit space key):
Code Address: 0x80010000, Entry Address: 0x801a2018
Decompression OK!
Entry at 0x801a2018
Closing network.
Starting program at 0x801a2018
Linux version 2.6.8.1 ( Compiled by michaelc) (gcc version 3.4.2) #1 Tue Jun 23 16:51:09 CST 2009

Flash Config: CS0(1fc00009,17),Base(bfc00000),Size(4MB)
Parallel flash device: name AM29LV320MB, id 0x2200, size 4096KB
Total Flash size: 4096K with 71 sectors
FLASH_BASE bfc00000,blk 0
bootf1=78 bootf2=ff
CPU revision is: 00029010
Determined physical RAM map:
memory: 00fa0000 @ 00000000 (usable)
On node 0 totalpages: 4000
  DMA zone: 4000 pages, LIFO batch:1
  Normal zone: 0 pages, LIFO batch:1
  HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd
brcm mips: enabling icache and dcache...
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.

Primary data cache 8kB 2-way, linesize 16 bytes.
PID hash table entries: 64 (order 6: 512 bytes)
Using 120.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 13968k/16000k available (1401k kernel code, 2012k reserved, 202k data, 68k init, 0k highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80e00000 ... 0x80f00000>
Calibrating delay loop... 239.20 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...  unavailable.
NET: Registered protocol family 16
Can't analyze prologue code at 8016ce74
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v1.0
bootf1=78 bootf2=ff
rootfs_addr 0bfc10100
brcmboard: brcm_board_init entry
Serial number:CS1621Z131A176007734
bcm963xx_serial driver v2.0
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 1024)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 68k freed
init started:  BusyBox v1.00 (2009.06.23-08:55+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
BusyBox v1.00 (2009.06.23-08:55+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
atmapi: module license 'Proprietary' taints kernel.
blaadd: blaa_detect entry
adsl: adsl_init entry
Broadcom BCMPROCFS v1.0 initialized
Internal PHY
Broadcom BCM6338A2 Ethernet Network Device v0.3 Jun 23 2009 16:49:38
Config Internal PHY Through MDIO
BCM63xx_ENET: 100 MB Full-Duplex (auto-neg)
eth0: MAC Address: 00:1B:9E:26:79:45
Broadcom BCM6338A2 USB Network Device v0.4 Jun 23 2009 16:49:40
usb0: MAC Address: 00 1B 9E 26 79 46
usb0: Host MAC Address: 00 1B 9E 26 79 47
USB Vendor id=069a, USB Product id=0316
eth0 Link UP.
BcmAdsl_Initialize=0xC0062878, g_pFnNotifyCallback=0xC007B894
AnnexCParam=0x7FFF7EA8 AnnexAParam=0x00000980 adsl2=0x00000000
pSdramPHY=0xA0FFFFF8, 0x8037C 0xDEADBEEF
AdslCoreHwReset: AdslOemDataAddr = 0xA0FEF96C
AnnexCParam=0x7FFF7EA8 AnnexAParam=0x00000980 adsl2=0x00000000
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
ATM proc init !!!D%GDGGGGGGGGG%GD%GD%DDDDDDD%
==>   Siemens ADSL CL-110 Software Version: 3.64z_A2pB025D%G -
pvc2684d: Interface "nas_8_35" created sucessfully
pvc2684d: Communicating over ATM 0.8.35, encapsulation: LLC
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (125 buckets, 0 max) - 368 bytes per conntrack
ip_conntrack_pptp version 2.1 loaded
ip_nat_pptp version 2.0 loaded
ip_conntrack_h323: init
ip_nat_h323: initialize the module!
ip_conntrack_rtsp v0.01 loading
ip_nat_rtsp v0.01 loading
board_ioctl: boot complete!
Boot finished and auto provision on lan not triggered: Exit from autoprovisionlan process

BCM6358
r18635, use vlan, the lan unwork, but in r17079, the vlan is work.

my network config

config switch eth1
    option vlan0 '0 1 2 5*'
    option vlan1 '3 5*'

config 'interface' 'lan'
    option 'type' 'bridge'
    option 'ifname' 'eth1.0'
    option 'proto' 'static'
    option 'ipaddr' '192.168.1.1'
    option 'netmask' '255.255.255.0'
    option 'nat' '1'

config 'interface' 'wan'
    option 'ifname' 'eth1.1'

Hi guys.

I've got myself a BCM6348 asus wl-600g at my disposal. I want to spend a bit of time working on this and bringing more info/better software to this platform.

How can I help making openwrt better on this device?

Is it possible to bring the binary ADSL drivers over to the openwrt image? How would I go about doing this?

wpa-supplicant isn't working yet, should I attempt to simply cross compile the existing source?

Any pointers would be greatly appreciated!

(Last edited by rockofclay on 8 Dec 2009, 00:44)

Hello,

I have a broadcom 6348 based device with two usb 1.1 port: one host and one slave. Is there any way to "convert" the slave port into master port because I don't want to use an usb hub and Broadcom says the slave port is configurable.

Thanks.

ps: sorry for my bad english.

nono2lozere:

the USB host port on the 6348 is certainly configurable, but not to act as a device (as opposed to host) port.

marc.

marca56:

I have one host port witch work perfectly but I also have a slave port that I want to use as a host port like broadcom says.

thanks

Hi, I have a DG834GT, and I'm trying to use misterox's method to make an image that I can flash using the web interface.

fahad@pyramid:~/DG834GT$ tools/makeImage openwrt.img DG834GT_1.03.22.img bcm963xx_fs_kernel
Image Error!

I fixed the problem by commenting out a line in the source of tools/makeImage

If anyone here has a DG834GT, http://pyramid.cluenet.org/~fahad/crap/ … g834gt.img

EDIt 17:43 13/01/2010: Changed URL

(Last edited by fahadsadah on 13 Jan 2010, 18:43)

Hi,

Does any one have the CFE.bin for WL-600G R1.61

My router is dead.
Thanks

Hi, I've met a strange issue for my brcm6358 router--RG-100A. It's a special version from china telecom.
as the DSL driver is missing, I've to use the vlan to split a port for wan.
And for the rest 3 port, when I use ssh to connect the router, it works fine. BUT, when I do scp/ftp to the router, it fails. I've checked from google and it said there is a issue for the switch. Is there any patch for this?
My openwrt version is r18957.

by the way, how to apply a patch for the trunk code? There is no bin file suitable for my router as it uses a 16MB flash.
I've found a patch from a chinese forum.
Here it is, only the delta part.
the file is target/linux/brcm63xx/image/Makefile

define Image/Build/RG100A
    # Generate the tagged image
    $(STAGING_DIR_HOST)/bin/imagetag -i $(KDIR)/vmlinux.lzma.cfe -f $(KDIR)/root.$(1) \
        -o $(BIN_DIR)/openwrt-$(6)-$(1)-$(7)-cfe.bin \
        -b $(2) -c $(3) -e $(LOADADDR) -l $(LOADADDR) \
        -k 0x20000 -n $(4) -t $(5)
endef

$(call Image/Build/RG100A,$(1),96358VW2,6358,0x20000,bc310,rg100a,bc310)

Is there any body can help to add this to svn?

Hi,

I'd like to add support for my DLink DSL-2500, which is a 2M/8M device based on the Broadcom 96332 CPU (see http://www.modem-help.co.uk/Broadcom/BC … ml?info=1)

I have found the board description in the GPL'd sources provided by DLink, which look like:

static BOARD_PARAMETERS g_dsl_2500u =
{
    "DSL-2500U",                            /* szBoardId */
    BP_NOT_DEFINED,                         /* usGPIOOverlay */

    BP_NOT_DEFINED,                         /* usGpioRj11InnerPair */
    BP_NOT_DEFINED,                         /* usGpioRj11OuterPair */
    BP_NOT_DEFINED,                         /* usGpioUartRts */
    BP_NOT_DEFINED,                         /* usGpioUartCts */
    BP_NOT_DEFINED,                         /* usVcopeResetGpio */
    BP_NOT_DEFINED,                         /* usVcopeRelayGpio */

    BP_GPIO_2_AL,                           /* usGpioLedAdsl */
    BP_GPIO_2_AH,                         /* usGpioLedAdslFail */
    BP_NOT_DEFINED,                         /* usGpioSecLedAdsl */
    BP_NOT_DEFINED,                         /* usGpioSecLedAdslFail */
    BP_NOT_DEFINED,                         /* usGpioLedSesWireless */     
    BP_NOT_DEFINED,                         /* usGpioLedHpna */
    BP_GPIO_4_AH,                                                                                                                      /* usGpioLedWanData */
    BP_NOT_DEFINED,                         /* usGpioLedPpp */
    BP_GPIO_3_AL,                           /* usGpioLedPppFail */
    BP_GPIO_0_AL,                           /* usGpioLedBlPowerOn */
    BP_GPIO_1_AL,                           /* usGpioLedBlStop */
    BP_NOT_DEFINED,                         /* usGpioBondingSecondaryReset */

    BP_HW_DEFINED,                          /* usExtIntrAdslDyingGasp */
    BP_EXT_INTR_1,                          /* usExtIntrResetToDefault */
    BP_NOT_DEFINED,                         /* usExtIntrSesBtnWireless */
    BP_NOT_DEFINED,                         /* usExtIntrHpna */

    BP_NOT_DEFINED,                         /* usCsHpna */
    BP_NOT_DEFINED,                         /* usCsHpi */

    BP_NOT_DEFINED,                         /* usAntInUseWireless */
    0,                                      /* WLAN flags */

    BP_NOT_DEFINED,                         /* usVcopeBoardRev */

    {{BP_ENET_INTERNAL_PHY,                 /* ucPhyType */
      0x01,                                 /* ucPhyAddress */
      BP_NOT_DEFINED,                       /* usGpioPhyReset */
      BP_NOT_DEFINED,                       /* usGpioPhyLinkSpeed */
      0x01,                                 /* numSwitchPorts */
      BP_ENET_CONFIG_MDIO,                  /* usConfigType */
      BP_NOT_DEFINED},                      /* usReverseMii */
     {BP_ENET_NO_PHY}},                     /* ucPhyType */
    {{BP_VOIP_NO_DSP},                      /* ucDspType */
     {BP_VOIP_NO_DSP}},                     /* ucDspType */
    Slic_Not_Defined,                       /* SLIC type */
    DAA_Not_Defined,                        /* DAA type */
    /* ALPHA_LED */
    BP_NOT_DEFINED                                                                                                             /* usGpioLedStatus */
};

Can anyone assist me to build a suitable profile of this board?

Hi, all!

I have DLink DSL-2650U (bcm6358). After little patching Makefile to add 96358VW2 targer, router successfuly flashed by openwrt-96358VW2-squashfs-dsl2650u-cfe.bin.

Index: target/linux/brcm63xx/image/Makefile
===================================================================
--- target/linux/brcm63xx/image/Makefile    (revision 19253)
+++ target/linux/brcm63xx/image/Makefile    (working copy)
@@ -163,6 +163,8 @@
     $(call Image/Build/CFE,$(1),F@ST2404,6348,bc310,OpenWRT-$(REVISION),bc310)
     # Inventel Livebox
     $(call Image/Build/RedBoot,livebox)
+    # D-Link DSL-2650U
+    $(call Image/Build/CFE,$(1),96358VW2,6358,bc310,,dsl2650u)
     # D-Link DSL-2740B
     $(call Image/Build/CFE,$(1),96358GW,6358,bc310,,dsl2740b)
     # Pirelli Alice Gate VoIP 2 Plus Wi-Fi AGPF-S0

Here is startup log:

CFE version 1.0.37-10.1 for BCM96358 (32bit,SP,BE)                         
Build Date: Tue Apr 24 15:57:24 CST 2007 (gavin@FD5)
Copyright (C) 2000-2006 Broadcom Corporation.

Boot Address 0xbe000000

Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MB, id 0x2200, size 8192KB
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)

Total memory used by CFE:  0x80401000 - 0x80527C50 (1207376)
Initialized Data:          0x8041D580 - 0x8041F480 (7936)
BSS Area:                  0x8041F480 - 0x80425C50 (26576)
Local Heap:                0x80425C50 - 0x80525C50 (1048576)
Stack Area:                0x80525C50 - 0x80527C50 (8192)
Text (code) segment:       0x80401000 - 0x8041D57C (116092)
Boot area (physical):      0x00528000 - 0x00568000
Relocation Factor:         I:00000000 - D:00000000

Board IP address                  : 192.168.1.1:ffffff00  
Host IP address                   : 192.168.1.2  
Gateway IP address                :   
Run from flash/host (f/h)         : f  
Default host run file name        :   
Default host flash file name      : openwrt-96358VW2-squashfs-dsl2650u-cfe.bin  
Boot delay (0-9 seconds)          : 1  
Board Id (0-8)                    : 96358VW2  
Number of MAC Addresses (1-32)    : 12  
Base MAC Address                  : 00:22:b0:xx:xx:xx  
PSI Size (1-64) KBytes            : 24  
Main Thread Number [0|1]          : 0  

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xbe010000) ...
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.30.10 (tipok@mythbox) (gcc version 4.3.3 (GCC) ) #2 Thu Jan 21 16:01:38 EET 2010
Detected Broadcom 0x6358 CPU revision a1
CPU frequency is 300000000 Hz
32MB of RAM installed
registering 40 GPIOs
board_bcm963xx: CFE version: 1.0.37-10.1
console [early0] enabled
CPU revision is: 0002a010 (Broadcom BCM6358)
board_bcm963xx: board name: 96358VW2
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
Primary instruction cache 32kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
NR_IRQS:128
PID hash table entries: 128 (order: 7, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29512k/32768k available (2073k kernel code, 3256k reserved, 428k data, 132k init, 0k highmem)
Calibrating delay loop... 299.00 BogoMIPS (lpj=598016)
Mount-cache hash table entries: 512
net_namespace: 532 bytes
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(0.306:1): initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  ?© 2001-2006 Red Hat, Inc.
msgmni has been set to 57
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
console handover: boot [early0] -> real [ttyS0]
bcm63xx_enet MII bus: probed
bcm963xx_flash: 0x02000000 at 0x1e000000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6, board type 96358VW2, and tagid bc310.
bcm963xx_flash: Partition 0 is CFE offset 0 and length 10000
bcm963xx_flash: Partition 1 is kernel offset 10100 and length dff00
bcm963xx_flash: Partition 2 is rootfs offset f0000 and length 700000
bcm963xx_flash: Partition 3 is nvram offset 7f0000 and length 10000
bcm963xx_flash: Partition 4 is linux offset 10000 and length 7e0000
bcm963xx_flash: Spare partition is 260000 offset and length 590000
Creating 5 MTD partitions on "bcm963xx":
0x000000000000-0x000000010000 : "CFE"
0x000000010100-0x0000000f0000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-oy
0x0000000f0000-0x0000007f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=260000, len=590000 
0x000000260000-0x0000007f0000 : "rootfs_data"
0x0000007f0000-0x000000800000 : "nvram"
0x000000010000-0x0000007f0000 : "linux"
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: adsl
Registered led device: ppp-fail
Registered led device: power
Registered led device: stop
Registered led device: <NULL>
leds-gpio: probe of leds-gpio.0 failed with error -16
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 132k freed
Please be patient, while OpenWrt loads ...
- preinit -
Press CTRL-C for failsafe
switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
- init -

Please press Enter to activate this console. bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (2)]
eth1: link forced UP - 100/full - flow control off/off
device eth1 entered promiscuous mode
br-lan: port 1(eth1) entering forwarding state
Generic kernel compatibility enabled based on linux-next next-20100113
cfg80211: Calling CRDA to update world regulatory domain
roboswitch: Probing device eth0: Failed to enable switch
roboswitch: Probing device eth1: found a 5325! It's a 5350.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 8
NET: Registered protocol family 20
b43-phy0: Broadcom 4318 WLAN found (core revision 9)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (512 buckets, 2048 max)
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 1
bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd: USB Universal Host Controller Interface driver

This device also have 1 additional USB and 5th ethernet port (it goes into broadcom main cpu) on pcb, but connectors are not soldered.

(Last edited by tipok on 1 Jun 2010, 12:21)

Hi
Has anyone ran OpenWrt on Linksys WAG325N or WAG320N ?

Hi All, I just meet some strange things.
My route is a brcm6358VW2 based route with CFE version 3.10.
When I flash it with the trunk version 19374, it just works fine. but when i try to use VLAN to allow wan and lan, it gets issues. For lan, scp will get failure, for wan, pppoe get failure
Then i finally find that when i decrease the MTU for lan from 1500 to 1490, scp works fine, and 1450 for wan, then pppoe works perfect.

As i nerver find any post about this issue, i'm not sure it is a bug or just some standard for VLAN usage.
Here is my /etc/config/network

config switch eth1
        option reset 1
        option enable_vlan 1

config switch_vlan
        option device eth1
        option vlan 0
        option ports "0 1 2 5*"

config switch_vlan
        option device eth1
        option vlan 1
        option ports "3 4 5*"

config interface loopback
        option ifname   lo
        option proto    static
        option ipaddr   127.0.0.1
        option netmask  255.0.0.0

config interface lan
        option type     bridge
        option ifname   eth1.0
        option proto    static
        option ipaddr   192.168.1.1
        option netmask  255.255.255.0
        option mtu      1490
        option nat      1

config atm-bridge
        option unit     0
        option encaps   llc
        option vpi      8
        option vci      35
        option payload  bridged

config interface wan
        option ifname   eth1.1
        option proto    pppoe
        option username username
        option password password
        option keepalive 10
        option mtu       1450

Successfully flashed onto a Linksys WAG54GS, uploaded from CFE using serial console.

CFE> f openwrt-96348GW-10-squashfs-bc300-cfe.bin
Loading 192.168.2.250:openwrt-96348GW-10-squashfs-bc300-cfe.bin ...
Finished loading 2686980 bytes

Flashing root file system and kernel: Normal----------------------
..........................................

.
*** Image flash done *** !
Resetting board...?

CFE version 1.0.37-5.11 for BCM96348 (32bit,SP,BE)
Build Date: ?  5? 17 17:00:38 CST 2005 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.

Initializing Arena.
Initializing Devices.
internal_open
bcm6348enet: init_emac
CPU type 0x29107: 240MHz, Bus: 133MHz, Ref: 26MHz

Total memory used by CFE:  0x80401000 - 0x8051CD00 (1162496)
Initialized Data:          0x804189C0 - 0x80419670 (3248)
BSS Area:                  0x80419670 - 0x8041AD00 (5776)
Local Heap:                0x8041AD00 - 0x8051AD00 (1048576)
Stack Area:                0x8051AD00 - 0x8051CD00 (8192)
Text (code) segment:       0x80401000 - 0x804189B8 (96696)
Boot area (physical):      0x0051D000 - 0x0055D000
Relocation Factor:         I:00000000 - D:00000000

Board IP address                : 192.168.2.240:ffffff00  
Host IP address                 : 192.168.2.250  
Gateway IP address              :   
Run from flash/host (f/h)       : f  
Default host run file name      : vmlinux  
Default host flash file name    : bcm963xx_fs_kernel  
Boot delay (0-9 seconds)        : 1  
Board Id Name                   : 96348GW-10  
Psi size in KB                  : 16
Number of MAC Addresses (1-32)  : 10  
Base MAC Address                : 00:18:39:8a:5e:88  
Ethernet PHY Type               : Internal
Memory size in MB               : 16

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.30.10 (buildbot@tksite) (gcc version 4.3.3 (GCC) ) #1 Fri Feb 5 22:49:19 CST 2010
Detected Broadcom 0x6348 CPU revision b0
CPU frequency is 240000000 Hz
16MB of RAM installed
registering 37 GPIOs
board_bcm963xx: CFE version: unknown
console [early0] enabled
CPU revision is: 00029107 (Broadcom BCM6348)
board_bcm963xx: board name: 96348GW-10
Determined physical RAM map:
 memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00001000
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
NR_IRQS:128
PID hash table entries: 64 (order: 6, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 13080k/16384k available (2168k kernel code, 3304k reserved, 516k data, 136k init, 0k highmem)
Calibrating delay loop... 239.10 BogoMIPS (lpj=478208)
Mount-cache hash table entries: 512
net_namespace: 1012 bytes
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
pci 0000:01:1e.0: CardBus bridge, secondary bus 0000:02
pci 0000:01:1e.0:   IO window: 0x8008000-0x80080ff
pci 0000:01:1e.0:   IO window: 0x8008400-0x80084ff
pci 0000:01:1e.0:   MEM window: 0x38000000-0x3fffffff
PCI: Enabling device 0000:01:1e.0 (0000 -> 0003)
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(0.349:1): initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
msgmni has been set to 25
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
console handover: boot [early0] -> real [ttyS0]
bcm63xx_enet MII bus: probed
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6, board type 96348GW-10, and tagid bc300.
bcm963xx_flash: Partition 0 is CFE offset 803f2920 and length 0
bcm963xx_flash: Partition 1 is kernel offset f6f and length 0
bcm963xx_flash: Partition 2 is rootfs offset fb0 and length 0
bcm963xx_flash: Partition 3 is nvram offset ff1 and length 0
bcm963xx_flash: Partition 4 is linux offset 1031 and length 0
bcm963xx_flash: Spare partition is 2a0000 offset and length 150000
Creating 5 MTD partitions on "bcm963xx":
0x000000000000-0x000000010000 : "CFE"
0x000000010100-0x000000100000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x000000100000-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=2A0000, len=150000 
0x0000002a0000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "nvram"
0x000000010000-0x0000003f0000 : "linux"
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: adsl-fail
Registered led device: ppp
Registered led device: ppp-fail
Registered led device: power
Registered led device: stop
leds-gpio: probe of leds-gpio.0 failed with error -16
TCP westwood registered
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 136k freed
Please be patient, while OpenWrt loads ...
- preinit -
Press Press f<ENTER> to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
mini_fo: using base directory: /
mini_fo: using storage directory: /tmp/root
- init -

Please press Enter to activate this console. bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (1)]
eth1: link forced UP - 100/full - flow control off/off
device eth1 entered promiscuous mode
br-lan: port 1(eth1) entering forwarding state
Generic kernel compatibility enabled based on linux-next next-20100113
cfg80211: Calling CRDA to update world regulatory domain
roboswitch: Probing device eth0: Failed to enable switch
roboswitch: Probing device eth1: found a 5325! It's a 5350.
b43-phy0: Broadcom 4318 WLAN found (core revision 9)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (256 buckets, 1024 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
jffs2_build_filesystem(): unlocking the mtd device... done.
jffs2_build_filesystem(): erasing all blocks after the end marker... done.
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs



BusyBox v1.15.3 (2010-02-05 04:09:36 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 KAMIKAZE (bleeding edge, r19530) ------------------
  * 10 oz Vodka       Shake well with ice and strain
  * 10 oz Triple sec  mixture into 10 shot glasses.
  * 10 oz lime juice  Salute!
 ---------------------------------------------------

(Last edited by Beezer on 8 Feb 2010, 21:23)