OpenWrt Forum Archive

Topic: Asus WL-520GU (WL-500GPv2) with kernel 2.6 and open source b43 driver

The content of this topic has been archived on 4 May 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

Post #1
SaTaN
12 Sep 2009, 14:09

DISCLAIMER:
If you brick your device following this instructions, it's NOT my fault!!!!!!

The Asus WL-520GU, WL-500GPv2, and probably other routers are built upon the BCM5354 SoC with built in LP PHY.

Thanks to Stefanik Gabor (Sorry if I messed your name), the Open Source b43 driver now has b43 support !

I compiled a patch to upgrade trunk to use compat-wireless-02-09-09, including LP PHY support.

Special Thanks also to Petr Kubin to fix a crash with this driver.

WHAT'S TESTED:
*) connecting to WPA2 PSK protected AP as STA

ISSUES:
*) Only 1 Mbit/s
*) I had massive issues with the configuration. now I used my own script (in openwrt), and it works.

here are the instructions:

mkdir openwrt
cd openwrt
# the patch is against trunk 17570
svn co svn://svn.openwrt.org/openwrt/trunk/ -r 17570 .
# check if patch applies clean
patch -p1 --dry-run < ../wl520gu.patch
# if no errors are shown, apply patch
patch -p1 < ../wl520gu.patch
# compile
make menuconfig
make
# now install: power-cycle  your router while keeping the reset switch pressed, when it blinks w/ 1 Hz, do:
atftp --trace --option "timeout 1" --option "mode octet" --put --local-file bin/openwrt-brcm47xx-squashfs.trx 192.168.1.1
# you must set up your ethernet device to 192.168.1.x, where x > 1, and also connect the router on LAN1.

After some time, powercycle the router again.
Now LAN1 won't work any more (you have to mess w/ the switch cfg), so use LAN4

login to your router on 192.168.1.1 via telnet and configure


here is my config:

CONFIG_HAVE_DOT_CONFIG=y
CONFIG_TARGET_brcm47xx=y
CONFIG_TARGET_brcm47xx_None=y
CONFIG_TARGET_BOARD="brcm47xx"
CONFIG_DEFAULT_TARGET_OPTIMIZATION="-Os -pipe -mips32 -mtune=mips32 -funit-at-a-time"
CONFIG_LINUX_2_6_28=y
CONFIG_DEFAULT_base-files=y
CONFIG_DEFAULT_busybox=y
CONFIG_DEFAULT_dnsmasq=y
CONFIG_DEFAULT_dropbear=y
CONFIG_DEFAULT_firewall=y
CONFIG_DEFAULT_hotplug2=y
CONFIG_DEFAULT_iptables=y
CONFIG_DEFAULT_kmod-diag=y
CONFIG_DEFAULT_kmod-ipt-nathelper=y
CONFIG_DEFAULT_kmod-switch=y
CONFIG_DEFAULT_libc=y
CONFIG_DEFAULT_libgcc=y
CONFIG_DEFAULT_mtd=y
CONFIG_DEFAULT_nvram=y
CONFIG_DEFAULT_opkg=y
CONFIG_DEFAULT_ppp=y
CONFIG_DEFAULT_ppp-mod-pppoe=y
CONFIG_DEFAULT_uci=y
CONFIG_DEFAULT_ucitrigger=y
CONFIG_DEFAULT_udevtrigger=y
CONFIG_LINUX_2_6=y
CONFIG_GPIO_SUPPORT=y
CONFIG_PCI_SUPPORT=y
CONFIG_USB_SUPPORT=y
CONFIG_USES_SQUASHFS=y
CONFIG_mipsel=y
CONFIG_ARCH="mipsel"
CONFIG_TARGET_ROOTFS_SQUASHFS=y
CONFIG_OLPC_BOOTSCRIPT_ROOTPART="/dev/sda2"
CONFIG_X86_GRUB_ROOTPART="/dev/hda2"
CONFIG_X86_GRUB_BOOTOPTS=""
CONFIG_LARGEFILE=y
CONFIG_SHADOW_PASSWORDS=y
CONFIG_USE_SSTRIP=y
CONFIG_KERNEL_DEBUG_FS=y
CONFIG_DOWNLOAD_FOLDER=""
CONFIG_AUTOREBUILD=y
CONFIG_BUILD_SUFFIX=""
CONFIG_TARGET_ROOTFS_DIR=""
CONFIG_EXTERNAL_KERNEL_TREE=""
CONFIG_KERNEL_GIT_CLONE_URI=""
CONFIG_KERNEL_GIT_LOCAL_REPOSITORY=""
CONFIG_TARGET_OPTIMIZATION="-Os -pipe -mips32 -mtune=mips32 -funit-at-a-time"
CONFIG_SOFT_FLOAT=y
CONFIG_EXTRA_BINUTILS_CONFIG_OPTIONS=""
CONFIG_BINUTILS_VERSION="2.19.1"
CONFIG_EXTRA_GCC_CONFIG_OPTIONS=""
CONFIG_INSTALL_LIBSTDCPP=y
CONFIG_USE_UCLIBC=y
CONFIG_GCC_VERSION="4.1.2"
CONFIG_UCLIBC_VERSION="0.9.30.1"
CONFIG_LIBC="uClibc"
CONFIG_LIBC_VERSION="0.9.30.1"
CONFIG_TARGET_SUFFIX="uclibc"
CONFIG_UCI_PRECONFIG=y
CONFIG_UCI_PRECONFIG_network_lan_dns=""
CONFIG_UCI_PRECONFIG_network_lan_proto="static"
CONFIG_UCI_PRECONFIG_network_lan_gateway=""
CONFIG_UCI_PRECONFIG_network_lan_netmask="255.255.255.0"
CONFIG_UCI_PRECONFIG_network_lan_ipaddr="192.168.1.1"
CONFIG_PACKAGE_base-files=y
CONFIG_PACKAGE_busybox=y
CONFIG_BUSYBOX_CONFIG_FEATURE_2_6_MODULES=y
CONFIG_BUSYBOX_CONFIG_HAVE_DOT_CONFIG=y
CONFIG_BUSYBOX_CONFIG_FEATURE_BUFFERS_GO_ON_STACK=y
CONFIG_BUSYBOX_CONFIG_SHOW_USAGE=y
CONFIG_BUSYBOX_CONFIG_FEATURE_VERBOSE_USAGE=y
CONFIG_BUSYBOX_CONFIG_FEATURE_COMPRESS_USAGE=y
CONFIG_BUSYBOX_CONFIG_GETOPT_LONG=y
CONFIG_BUSYBOX_CONFIG_FEATURE_DEVPTS=y
CONFIG_BUSYBOX_CONFIG_FEATURE_PIDFILE=y
CONFIG_BUSYBOX_CONFIG_FEATURE_SUID=y
CONFIG_BUSYBOX_CONFIG_FEATURE_PREFER_APPLETS=y
CONFIG_BUSYBOX_CONFIG_BUSYBOX_EXEC_PATH="/proc/self/exe"
CONFIG_BUSYBOX_CONFIG_FEATURE_SYSLOG=y
CONFIG_BUSYBOX_CONFIG_FEATURE_HAVE_RPC=y
CONFIG_BUSYBOX_CONFIG_LFS=y
CONFIG_BUSYBOX_CONFIG_CROSS_COMPILER_PREFIX=""
CONFIG_BUSYBOX_CONFIG_NO_DEBUG_LIB=y
CONFIG_BUSYBOX_CONFIG_INCLUDE_SUSv2=y
CONFIG_BUSYBOX_CONFIG_INSTALL_APPLET_SYMLINKS=y
CONFIG_BUSYBOX_CONFIG_PREFIX="./_install"
CONFIG_BUSYBOX_CONFIG_PASSWORD_MINLEN=6
CONFIG_BUSYBOX_CONFIG_MD5_SIZE_VS_SPEED=2
CONFIG_BUSYBOX_CONFIG_FEATURE_FAST_TOP=y
CONFIG_BUSYBOX_CONFIG_FEATURE_EDITING=y
CONFIG_BUSYBOX_CONFIG_FEATURE_EDITING_MAX_LEN=512
CONFIG_BUSYBOX_CONFIG_FEATURE_EDITING_HISTORY=256
CONFIG_BUSYBOX_CONFIG_FEATURE_TAB_COMPLETION=y
CONFIG_BUSYBOX_CONFIG_FEATURE_EDITING_FANCY_PROMPT=y
CONFIG_BUSYBOX_CONFIG_FEATURE_COPYBUF_KB=4
CONFIG_BUSYBOX_CONFIG_IOCTL_HEX2STR_ERROR=y
CONFIG_BUSYBOX_CONFIG_FEATURE_SEAMLESS_GZ=y
CONFIG_BUSYBOX_CONFIG_BUNZIP2=y
CONFIG_BUSYBOX_CONFIG_GUNZIP=y
CONFIG_BUSYBOX_CONFIG_GZIP=y
CONFIG_BUSYBOX_CONFIG_TAR=y
CONFIG_BUSYBOX_CONFIG_FEATURE_TAR_CREATE=y
CONFIG_BUSYBOX_CONFIG_FEATURE_TAR_FROM=y
CONFIG_BUSYBOX_CONFIG_FEATURE_TAR_GNU_EXTENSIONS=y
CONFIG_BUSYBOX_CONFIG_BASENAME=y
CONFIG_BUSYBOX_CONFIG_CAT=y
CONFIG_BUSYBOX_CONFIG_CHGRP=y
CONFIG_BUSYBOX_CONFIG_CHMOD=y
CONFIG_BUSYBOX_CONFIG_CHOWN=y
CONFIG_BUSYBOX_CONFIG_CHROOT=y
CONFIG_BUSYBOX_CONFIG_CP=y
CONFIG_BUSYBOX_CONFIG_CUT=y
CONFIG_BUSYBOX_CONFIG_DATE=y
CONFIG_BUSYBOX_CONFIG_FEATURE_DATE_ISOFMT=y
CONFIG_BUSYBOX_CONFIG_DD=y
CONFIG_BUSYBOX_CONFIG_FEATURE_DD_SIGNAL_HANDLING=y
CONFIG_BUSYBOX_CONFIG_DF=y
CONFIG_BUSYBOX_CONFIG_DIRNAME=y
CONFIG_BUSYBOX_CONFIG_DU=y
CONFIG_BUSYBOX_CONFIG_FEATURE_DU_DEFAULT_BLOCKSIZE_1K=y
CONFIG_BUSYBOX_CONFIG_ECHO=y
CONFIG_BUSYBOX_CONFIG_FEATURE_FANCY_ECHO=y
CONFIG_BUSYBOX_CONFIG_ENV=y
CONFIG_BUSYBOX_CONFIG_EXPR=y
CONFIG_BUSYBOX_CONFIG_FALSE=y
CONFIG_BUSYBOX_CONFIG_HEAD=y
CONFIG_BUSYBOX_CONFIG_FEATURE_FANCY_HEAD=y
CONFIG_BUSYBOX_CONFIG_HOSTID=y
CONFIG_BUSYBOX_CONFIG_ID=y
CONFIG_BUSYBOX_CONFIG_LENGTH=y
CONFIG_BUSYBOX_CONFIG_LN=y
CONFIG_BUSYBOX_CONFIG_LS=y
CONFIG_BUSYBOX_CONFIG_FEATURE_LS_FILETYPES=y
CONFIG_BUSYBOX_CONFIG_FEATURE_LS_FOLLOWLINKS=y
CONFIG_BUSYBOX_CONFIG_FEATURE_LS_RECURSIVE=y
CONFIG_BUSYBOX_CONFIG_FEATURE_LS_SORTFILES=y
CONFIG_BUSYBOX_CONFIG_FEATURE_LS_TIMESTAMPS=y
CONFIG_BUSYBOX_CONFIG_FEATURE_LS_USERNAME=y
CONFIG_BUSYBOX_CONFIG_FEATURE_LS_COLOR=y
CONFIG_BUSYBOX_CONFIG_FEATURE_LS_COLOR_IS_DEFAULT=y
CONFIG_BUSYBOX_CONFIG_MD5SUM=y
CONFIG_BUSYBOX_CONFIG_MKDIR=y
CONFIG_BUSYBOX_CONFIG_MKFIFO=y
CONFIG_BUSYBOX_CONFIG_MKNOD=y
CONFIG_BUSYBOX_CONFIG_MV=y
CONFIG_BUSYBOX_CONFIG_NICE=y
CONFIG_BUSYBOX_CONFIG_PRINTF=y
CONFIG_BUSYBOX_CONFIG_PWD=y
CONFIG_BUSYBOX_CONFIG_RM=y
CONFIG_BUSYBOX_CONFIG_RMDIR=y
CONFIG_BUSYBOX_CONFIG_SEQ=y
CONFIG_BUSYBOX_CONFIG_SLEEP=y
CONFIG_BUSYBOX_CONFIG_FEATURE_FANCY_SLEEP=y
CONFIG_BUSYBOX_CONFIG_SORT=y
CONFIG_BUSYBOX_CONFIG_SYNC=y
CONFIG_BUSYBOX_CONFIG_TAIL=y
CONFIG_BUSYBOX_CONFIG_FEATURE_FANCY_TAIL=y
CONFIG_BUSYBOX_CONFIG_TEE=y
CONFIG_BUSYBOX_CONFIG_FEATURE_TEE_USE_BLOCK_IO=y
CONFIG_BUSYBOX_CONFIG_TEST=y
CONFIG_BUSYBOX_CONFIG_TOUCH=y
CONFIG_BUSYBOX_CONFIG_TR=y
CONFIG_BUSYBOX_CONFIG_TRUE=y
CONFIG_BUSYBOX_CONFIG_UNAME=y
CONFIG_BUSYBOX_CONFIG_UNIQ=y
CONFIG_BUSYBOX_CONFIG_WC=y
CONFIG_BUSYBOX_CONFIG_YES=y
CONFIG_BUSYBOX_CONFIG_FEATURE_PRESERVE_HARDLINKS=y
CONFIG_BUSYBOX_CONFIG_FEATURE_AUTOWIDTH=y
CONFIG_BUSYBOX_CONFIG_FEATURE_HUMAN_READABLE=y
CONFIG_BUSYBOX_CONFIG_FEATURE_MD5_SHA1_SUM_CHECK=y
CONFIG_BUSYBOX_CONFIG_CLEAR=y
CONFIG_BUSYBOX_CONFIG_RESET=y
CONFIG_BUSYBOX_CONFIG_MKTEMP=y
CONFIG_BUSYBOX_CONFIG_START_STOP_DAEMON=y
CONFIG_BUSYBOX_CONFIG_WHICH=y
CONFIG_BUSYBOX_CONFIG_AWK=y
CONFIG_BUSYBOX_CONFIG_FEATURE_AWK_LIBM=y
CONFIG_BUSYBOX_CONFIG_DIFF=y
CONFIG_BUSYBOX_CONFIG_SED=y
CONFIG_BUSYBOX_CONFIG_VI=y
CONFIG_BUSYBOX_CONFIG_FEATURE_VI_MAX_LEN=1024
CONFIG_BUSYBOX_CONFIG_FEATURE_VI_COLON=y
CONFIG_BUSYBOX_CONFIG_FEATURE_VI_YANKMARK=y
CONFIG_BUSYBOX_CONFIG_FEATURE_VI_SEARCH=y
CONFIG_BUSYBOX_CONFIG_FEATURE_VI_USE_SIGNALS=y
CONFIG_BUSYBOX_CONFIG_FEATURE_VI_DOT_CMD=y
CONFIG_BUSYBOX_CONFIG_FEATURE_VI_READONLY=y
CONFIG_BUSYBOX_CONFIG_FEATURE_VI_SETOPTS=y
CONFIG_BUSYBOX_CONFIG_FEATURE_VI_SET=y
CONFIG_BUSYBOX_CONFIG_FEATURE_VI_WIN_RESIZE=y
CONFIG_BUSYBOX_CONFIG_FEATURE_VI_OPTIMIZE_CURSOR=y
CONFIG_BUSYBOX_CONFIG_FEATURE_ALLOW_EXEC=y
CONFIG_BUSYBOX_CONFIG_FIND=y
CONFIG_BUSYBOX_CONFIG_FEATURE_FIND_PRINT0=y
CONFIG_BUSYBOX_CONFIG_FEATURE_FIND_PERM=y
CONFIG_BUSYBOX_CONFIG_FEATURE_FIND_TYPE=y
CONFIG_BUSYBOX_CONFIG_FEATURE_FIND_XDEV=y
CONFIG_BUSYBOX_CONFIG_FEATURE_FIND_MAXDEPTH=y
CONFIG_BUSYBOX_CONFIG_FEATURE_FIND_EXEC=y
CONFIG_BUSYBOX_CONFIG_FEATURE_FIND_USER=y
CONFIG_BUSYBOX_CONFIG_FEATURE_FIND_GROUP=y
CONFIG_BUSYBOX_CONFIG_FEATURE_FIND_NOT=y
CONFIG_BUSYBOX_CONFIG_FEATURE_FIND_DEPTH=y
CONFIG_BUSYBOX_CONFIG_FEATURE_FIND_PAREN=y
CONFIG_BUSYBOX_CONFIG_FEATURE_FIND_SIZE=y
CONFIG_BUSYBOX_CONFIG_FEATURE_FIND_PRUNE=y
CONFIG_BUSYBOX_CONFIG_FEATURE_FIND_PATH=y
CONFIG_BUSYBOX_CONFIG_FEATURE_FIND_REGEX=y
CONFIG_BUSYBOX_CONFIG_GREP=y
CONFIG_BUSYBOX_CONFIG_FEATURE_GREP_EGREP_ALIAS=y
CONFIG_BUSYBOX_CONFIG_FEATURE_GREP_FGREP_ALIAS=y
CONFIG_BUSYBOX_CONFIG_FEATURE_GREP_CONTEXT=y
CONFIG_BUSYBOX_CONFIG_XARGS=y
CONFIG_BUSYBOX_CONFIG_FEATURE_XARGS_SUPPORT_CONFIRMATION=y
CONFIG_BUSYBOX_CONFIG_FEATURE_XARGS_SUPPORT_QUOTES=y
CONFIG_BUSYBOX_CONFIG_FEATURE_XARGS_SUPPORT_TERMOPT=y
CONFIG_BUSYBOX_CONFIG_FEATURE_XARGS_SUPPORT_ZERO_TERM=y
CONFIG_BUSYBOX_CONFIG_INIT=y
CONFIG_BUSYBOX_CONFIG_FEATURE_USE_INITTAB=y
CONFIG_BUSYBOX_CONFIG_FEATURE_KILL_DELAY=0
CONFIG_BUSYBOX_CONFIG_FEATURE_INIT_SYSLOG=y
CONFIG_BUSYBOX_CONFIG_HALT=y
CONFIG_BUSYBOX_CONFIG_MESG=y
CONFIG_BUSYBOX_CONFIG_PASSWD=y
CONFIG_BUSYBOX_CONFIG_FEATURE_PASSWD_WEAK_CHECK=y
CONFIG_BUSYBOX_CONFIG_DEFAULT_MODULES_DIR="/lib/modules"
CONFIG_BUSYBOX_CONFIG_DEFAULT_DEPMOD_FILE="modules.dep"
CONFIG_BUSYBOX_CONFIG_INSMOD=y
CONFIG_BUSYBOX_CONFIG_RMMOD=y
CONFIG_BUSYBOX_CONFIG_LSMOD=y
CONFIG_BUSYBOX_CONFIG_FEATURE_LSMOD_PRETTY_2_6_OUTPUT=y
CONFIG_BUSYBOX_CONFIG_FEATURE_CHECK_TAINTED_MODULE=y
CONFIG_BUSYBOX_CONFIG_DMESG=y
CONFIG_BUSYBOX_CONFIG_FEATURE_DMESG_PRETTY=y
CONFIG_BUSYBOX_CONFIG_FDISK_SUPPORT_LARGE_DISKS=y
CONFIG_BUSYBOX_CONFIG_HEXDUMP=y
CONFIG_BUSYBOX_CONFIG_HWCLOCK=y
CONFIG_BUSYBOX_CONFIG_MOUNT=y
CONFIG_BUSYBOX_CONFIG_FEATURE_MOUNT_NFS=y
CONFIG_BUSYBOX_CONFIG_FEATURE_MOUNT_CIFS=y
CONFIG_BUSYBOX_CONFIG_FEATURE_MOUNT_FLAGS=y
CONFIG_BUSYBOX_CONFIG_FEATURE_MOUNT_FSTAB=y
CONFIG_BUSYBOX_CONFIG_PIVOT_ROOT=y
CONFIG_BUSYBOX_CONFIG_RDATE=y
CONFIG_BUSYBOX_CONFIG_SWITCH_ROOT=y
CONFIG_BUSYBOX_CONFIG_UMOUNT=y
CONFIG_BUSYBOX_CONFIG_FEATURE_UMOUNT_ALL=y
CONFIG_BUSYBOX_CONFIG_FEATURE_MOUNT_LOOP=y
CONFIG_BUSYBOX_CONFIG_CROND=y
CONFIG_BUSYBOX_CONFIG_CRONTAB=y
CONFIG_BUSYBOX_CONFIG_LESS=y
CONFIG_BUSYBOX_CONFIG_FEATURE_LESS_MAXLINES=9999999
CONFIG_BUSYBOX_CONFIG_LOCK=y
CONFIG_BUSYBOX_CONFIG_STRINGS=y
CONFIG_BUSYBOX_CONFIG_TIME=y
CONFIG_BUSYBOX_CONFIG_WATCHDOG=y
CONFIG_BUSYBOX_CONFIG_FEATURE_IPV6=y
CONFIG_BUSYBOX_CONFIG_FEATURE_PREFER_IPV4_ADDRESS=y
CONFIG_BUSYBOX_CONFIG_VERBOSE_RESOLUTION_ERRORS=y
CONFIG_BUSYBOX_CONFIG_ARPING=y
CONFIG_BUSYBOX_CONFIG_BRCTL=y
CONFIG_BUSYBOX_CONFIG_FEATURE_BRCTL_FANCY=y
CONFIG_BUSYBOX_CONFIG_FEATURE_BRCTL_SHOW=y
CONFIG_BUSYBOX_CONFIG_HTTPD=y
CONFIG_BUSYBOX_CONFIG_FEATURE_HTTPD_RANGES=y
CONFIG_BUSYBOX_CONFIG_FEATURE_HTTPD_RELOAD_CONFIG_SIGHUP=y
CONFIG_BUSYBOX_CONFIG_FEATURE_HTTPD_BASIC_AUTH=y
CONFIG_BUSYBOX_CONFIG_FEATURE_HTTPD_AUTH_MD5=y
CONFIG_BUSYBOX_CONFIG_FEATURE_HTTPD_CONFIG_WITH_MIME_TYPES=y
CONFIG_BUSYBOX_CONFIG_FEATURE_HTTPD_CGI=y
CONFIG_BUSYBOX_CONFIG_FEATURE_HTTPD_CONFIG_WITH_SCRIPT_INTERPR=y
CONFIG_BUSYBOX_CONFIG_FEATURE_HTTPD_SET_REMOTE_PORT_TO_ENV=y
CONFIG_BUSYBOX_CONFIG_FEATURE_HTTPD_ENCODE_URL_STR=y
CONFIG_BUSYBOX_CONFIG_FEATURE_HTTPD_ERROR_PAGES=y
CONFIG_BUSYBOX_CONFIG_FEATURE_HTTPD_PROXY=y
CONFIG_BUSYBOX_CONFIG_IFCONFIG=y
CONFIG_BUSYBOX_CONFIG_FEATURE_IFCONFIG_STATUS=y
CONFIG_BUSYBOX_CONFIG_FEATURE_IFCONFIG_HW=y
CONFIG_BUSYBOX_CONFIG_FEATURE_IFCONFIG_BROADCAST_PLUS=y
CONFIG_BUSYBOX_CONFIG_NC=y
CONFIG_BUSYBOX_CONFIG_NETMSG=y
CONFIG_BUSYBOX_CONFIG_NETSTAT=y
CONFIG_BUSYBOX_CONFIG_FEATURE_NETSTAT_WIDE=y
CONFIG_BUSYBOX_CONFIG_FEATURE_NETSTAT_PRG=y
CONFIG_BUSYBOX_CONFIG_NSLOOKUP=y
CONFIG_BUSYBOX_CONFIG_PING=y
CONFIG_BUSYBOX_CONFIG_PING6=y
CONFIG_BUSYBOX_CONFIG_FEATURE_FANCY_PING=y
CONFIG_BUSYBOX_CONFIG_ROUTE=y
CONFIG_BUSYBOX_CONFIG_TELNET=y
CONFIG_BUSYBOX_CONFIG_FEATURE_TELNET_TTYPE=y
CONFIG_BUSYBOX_CONFIG_TELNETD=y
CONFIG_BUSYBOX_CONFIG_FEATURE_TELNETD_STANDALONE=y
CONFIG_BUSYBOX_CONFIG_TRACEROUTE=y
CONFIG_BUSYBOX_CONFIG_FEATURE_TRACEROUTE_VERBOSE=y
CONFIG_BUSYBOX_CONFIG_APP_UDHCPC=y
CONFIG_BUSYBOX_CONFIG_FEATURE_UDHCP_RFC3397=y
CONFIG_BUSYBOX_CONFIG_UDHCPC_DEFAULT_SCRIPT="/usr/share/udhcpc/default.script"
CONFIG_BUSYBOX_CONFIG_UDHCPC_SLACK_FOR_BUGGY_SERVERS=80
CONFIG_BUSYBOX_CONFIG_VCONFIG=y
CONFIG_BUSYBOX_CONFIG_WGET=y
CONFIG_BUSYBOX_CONFIG_FEATURE_WGET_STATUSBAR=y
CONFIG_BUSYBOX_CONFIG_FEATURE_WGET_AUTHENTICATION=y
CONFIG_BUSYBOX_CONFIG_FEATURE_WGET_LONG_OPTIONS=y
CONFIG_BUSYBOX_CONFIG_FREE=y
CONFIG_BUSYBOX_CONFIG_KILL=y
CONFIG_BUSYBOX_CONFIG_KILLALL=y
CONFIG_BUSYBOX_CONFIG_KILLALL5=y
CONFIG_BUSYBOX_CONFIG_PGREP=y
CONFIG_BUSYBOX_CONFIG_PIDOF=y
CONFIG_BUSYBOX_CONFIG_PKILL=y
CONFIG_BUSYBOX_CONFIG_PS=y
CONFIG_BUSYBOX_CONFIG_BB_SYSCTL=y
CONFIG_BUSYBOX_CONFIG_TOP=y
CONFIG_BUSYBOX_CONFIG_FEATURE_TOP_CPU_USAGE_PERCENTAGE=y
CONFIG_BUSYBOX_CONFIG_FEATURE_TOP_CPU_GLOBAL_PERCENTS=y
CONFIG_BUSYBOX_CONFIG_UPTIME=y
CONFIG_BUSYBOX_CONFIG_FEATURE_SH_IS_ASH=y
CONFIG_BUSYBOX_CONFIG_ASH=y
CONFIG_BUSYBOX_CONFIG_ASH_BASH_COMPAT=y
CONFIG_BUSYBOX_CONFIG_ASH_JOB_CONTROL=y
CONFIG_BUSYBOX_CONFIG_ASH_READ_TIMEOUT=y
CONFIG_BUSYBOX_CONFIG_ASH_ALIAS=y
CONFIG_BUSYBOX_CONFIG_ASH_MATH_SUPPORT=y
CONFIG_BUSYBOX_CONFIG_ASH_MATH_SUPPORT_64=y
CONFIG_BUSYBOX_CONFIG_ASH_GETOPTS=y
CONFIG_BUSYBOX_CONFIG_ASH_BUILTIN_ECHO=y
CONFIG_BUSYBOX_CONFIG_ASH_BUILTIN_PRINTF=y
CONFIG_BUSYBOX_CONFIG_ASH_BUILTIN_TEST=y
CONFIG_BUSYBOX_CONFIG_ASH_CMDCMD=y
CONFIG_BUSYBOX_CONFIG_ASH_EXPAND_PRMT=y
CONFIG_BUSYBOX_CONFIG_SYSLOGD=y
CONFIG_BUSYBOX_CONFIG_FEATURE_ROTATE_LOGFILE=y
CONFIG_BUSYBOX_CONFIG_FEATURE_REMOTE_LOG=y
CONFIG_BUSYBOX_CONFIG_FEATURE_IPC_SYSLOG=y
CONFIG_BUSYBOX_CONFIG_FEATURE_IPC_SYSLOG_BUFFER_SIZE=16
CONFIG_BUSYBOX_CONFIG_LOGREAD=y
CONFIG_BUSYBOX_CONFIG_KLOGD=y
CONFIG_BUSYBOX_CONFIG_LOGGER=y
CONFIG_PACKAGE_dnsmasq=y
CONFIG_PACKAGE_dropbear=y
CONFIG_PACKAGE_firewall=y
CONFIG_PACKAGE_hotplug2=y
CONFIG_PACKAGE_iptables=y
CONFIG_PACKAGE_iptables-mod-conntrack=y
CONFIG_PACKAGE_iptables-mod-nat=y
CONFIG_PACKAGE_libc=y
CONFIG_PACKAGE_libgcc=y
CONFIG_PACKAGE_mtd=y
CONFIG_PACKAGE_nvram=y
CONFIG_PACKAGE_opkg=y
CONFIG_PACKAGE_uci=y
CONFIG_PACKAGE_ucitrigger=y
CONFIG_PACKAGE_udevtrigger=y
CONFIG_PACKAGE_wireless-tools=y
CONFIG_PACKAGE_libiptc=y
CONFIG_PACKAGE_libiw=y
CONFIG_PACKAGE_liblua=y
CONFIG_PACKAGE_libnl-tiny=y
CONFIG_PACKAGE_libuci=y
CONFIG_PACKAGE_libuci-lua=y
CONFIG_PACKAGE_libxtables=y
CONFIG_PACKAGE_crda=y
CONFIG_PACKAGE_iw=y
CONFIG_PACKAGE_wpa-supplicant=y
CONFIG_WPA_SUPPLICANT_INTERNAL=y
CONFIG_PACKAGE_kmod-crypto-aes=y
CONFIG_PACKAGE_kmod-crypto-arc4=y
CONFIG_PACKAGE_kmod-crypto-core=y
CONFIG_PACKAGE_kmod-ipt-core=y
CONFIG_PACKAGE_kmod-ipt-conntrack=y
CONFIG_PACKAGE_kmod-ipt-nat=y
CONFIG_PACKAGE_kmod-ipt-nathelper=y
CONFIG_PACKAGE_kmod-crc-ccitt=y
CONFIG_PACKAGE_kmod-diag=y
CONFIG_PACKAGE_kmod-switch=y
CONFIG_PACKAGE_kmod-usb-core=y
CONFIG_PACKAGE_kmod-usb-ohci=y
CONFIG_PACKAGE_kmod-usb2=y
CONFIG_PACKAGE_kmod-b43=y
CONFIG_B43_STABLE=y
CONFIG_PACKAGE_kmod-mac80211=y
CONFIG_KEXEC_TOOLS_TARGET_NAME="mipsel"
CONFIG_PACKAGE_robocfg=y
CONFIG_PACKAGE_lua=y

NOTE: use the "No wireless option !!!"
setup wireless manually later.

here is the dmesg output:

root@OpenWrt:~# dmesg 
Linux version 2.6.28.10 (tom@note) (gcc version 4.1.2) #5 Sat Sep 12 12:57:21 CEST 2009
CPU revision is: 00029029 (Broadcom BCM3302)
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x14, vendor 0x4243)
ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x09, vendor 0x4243)
ssb: Core 2 found: MIPS 3302 (cc 0x816, rev 0x08, vendor 0x4243)
ssb: Core 3 found: USB 2.0 Host (cc 0x819, rev 0x02, vendor 0x4243)
ssb: Core 4 found: MEMC SDRAM (cc 0x80F, rev 0x04, vendor 0x4243)
ssb: Core 5 found: IEEE 802.11 (cc 0x812, rev 0x0D, vendor 0x4243)
ssb: Core 6 found: Roboswitch (cc 0x81C, rev 0x02, vendor 0x4243)
ssb: Found rev 0 PMU (capabilities 0x04A63400)
ssb: Initializing MIPS core...
ssb: core 0x0800, irq : 2(S)  3* 4  5  6  D  I 
ssb: core 0x0806, irq : 2(S)  3  4* 5  6  D  I 
ssb: core 0x0816, irq : 2(S)  3  4  5* 6  D  I 
ssb: core 0x0819, irq : 2(S)  3  4  5  6* D  I 
ssb: core 0x080f, irq : 2(S)  3  4  5  6  D  I*
ssb: core 0x0812, irq : 2(S)* 3  4  5  6  D  I 
ssb: core 0x081c, irq : 2(S)  3  4  5  6  D  I*
ssb: set_irq: core 0x0806, irq 4 => 4
ssb: set_irq: core 0x0816, irq 5 => 2
ssb: set_irq: core 0x0812, irq 2 => 5
ssb: after irq reconfiguration
ssb: core 0x0800, irq : 2(S)  3* 4  5  6  D  I 
ssb: core 0x0806, irq : 2(S)  3  4* 5  6  D  I 
ssb: core 0x0816, irq : 2(S)* 3  4  5  6  D  I 
ssb: core 0x0819, irq : 2(S)  3  4  5  6* D  I 
ssb: core 0x080f, irq : 2(S)  3  4  5  6  D  I*
ssb: core 0x0812, irq : 2(S)  3  4  5* 6  D  I 
ssb: core 0x081c, irq : 2(S)  3  4  5  6  D  I*
ssb: Sonics Silicon Backplane found at address 0x18000000
Serial init done.
Determined physical RAM map:
 memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00001000
On node 0 totalpages: 4096
free_area_init_node: node 0, pgdat 80268a00, node_mem_map 802b0000
  Normal zone: 32 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 4064 pages, LIFO batch:0
  Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
PID hash table entries: 64 (order: 6, 256 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 13488k/16384k available (2157k kernel code, 2896k reserved, 308k data, 136k init, 0k highmem)
Calibrating delay loop... 239.61 BogoMIPS (lpj=479232)
Mount-cache hash table entries: 512
net_namespace: 480 bytes
NET: Registered protocol family 16
Switched to high resolution mode on CPU 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
detected lzma initramfs
initramfs: LZMA lc=1,lp=2,pb=2,origSize=512
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
msgmni has been set to 26
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:1f:c6:7d:91:31
flash init: 0x1c000000 0x02000000
Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Physically mapped flash: Found an alias at 0x400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0xc00000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1c00000 for the chip at 0x0
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x400000 at 0x1fc00000
bootloader size: 131072
Creating 4 MTD partitions on "Physically mapped flash":
0x00000000-0x00020000 : "cfe"
0x00020000-0x003f0000 : "linux"
0x000edc00-0x003f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=280000, len=170000 
0x00280000-0x003f0000 : "rootfs_data"
0x003f0000-0x00400000 : "nvram"
BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 136k freed
Please be patient, while OpenWrt loads ...
diag: Detected 'ASUS WL-520gU'
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
roboswitch: Probing device eth0: found!
b44: eth0: powering down PHY
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
b43-phy0: Broadcom 5354 WLAN found (core revision 13)
phy0: Selected rate control algorithm 'minstrel'
Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
ip_tables: (C) 2000-2006 Netfilter Core Team
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
nf_conntrack version 0.5.0 (256 buckets, 1024 max)
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd ssb0:1: SSB OHCI Controller
ohci_hcd ssb0:1: new USB bus registered, assigned bus number 1
ohci_hcd ssb0:1: irq 6, io mem 0x18003000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd ssb0:1: SSB EHCI Controller
ohci_hcd ssb0:1: new USB bus registered, assigned bus number 2
ohci_hcd ssb0:1: irq 6, io mem 0x18003800
ohci_hcd ssb0:1: USB 0.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
b43 ssb0:3: firmware: requesting b43/ucode13.fw
b43 ssb0:3: firmware: requesting b43/lp0initvals13.fw
b43 ssb0:3: firmware: requesting b43/lp0bsinitvals13.fw
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
wlan0: direct probe to AP 803d222c (try 1)
wlan0 direct probe responded
wlan0: authenticate with AP 803d222c (try 1)
wlan0: authenticated
wlan0: associate with AP 803d222c (try 1)
wlan0: RX AssocResp from 804b906e (capab=0x431 status=0 aid=2)
wlan0: associated
cfg80211: Calling CRDA for country: DE
cfg80211: Current regulatory domain updated by AP to: DE
    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    (2402000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)

And here is the script that I needed to load the wireless:

#!/bin/sh /etc/rc.common
# Copyright (C) 2006 OpenWrt.org

START=40
STOP=40

boot() {
    # step1: sleep
    sleep 60 
    modprobe b43
    #this will load the firmware
    ifconfig wlan0 up
    #enable wpa_supplicant
    wpa_supplicant -iwlan0 -Dwext -c/etc/wpa_supplicant.conf -B
    #should be sufficient
    sleep 3
    udhcpc -t 0 -i wlan0 -b -p /var/run/wlan0.pid -R -h OpenWRT
}

start() {
    sleep 60
    modprobe b43
    ifconfig wlan0 up
    wpa_supplicant -iwlan0 -Dwext -c/etc/wpa_supplicant.conf -B
    sleep 3
    udhcpc -t 0 -i wlan0 -b -p /var/run/wlan0.pid -R -h OpenWRT
}

restart() {
    kill `cat /var/run/wlan0.pid`
    killall wpa_supplicant    
    ifconfig wlan0 down
    ifconfig wlan0 up
    wpa_supplicant -iwlan0 -Dwext -c/etc/wpa_supplicant.conf -B
    sleep 3
    udhcpc -t 0 -i wlan0 -b -p /var/run/wlan0.pid -R -h OpenWRT
}

stop() {
    kill `cat /var/run/wlan0.pid`
    killall wpa_supplicant
    ifdown -a
}

W/O the sleep statements, the b43 driver requires 3 trys to load the firmware (because the flash is accessed by other processes ?)

And finally, this is the patch (sorry for rapidshare):
http://rapidshare.com/files/279051949/w … patch.html

Post #2
Irek
18 Sep 2009, 09:01
SaTaN wrote:

DISCLAIMER:
And finally, this is the patch (sorry for rapidshare):
http://rapidshare.com/files/279051949/w … patch.html

To download this file, the uploader either needs to transfer this file into his/her Collector's Account, or upload the file again. The file can later be moved to a Collector's Account. The uploader just needs to click the delete link of the file to get further information.

Please ....

Post #4
Irek
21 Sep 2009, 14:07 
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
        (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
        (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
        (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Regulatory domain changed to country: US
        (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
        (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
        (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
        (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
        (5490000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
        (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
b43: Unknown symbol b43_pio_free
b43: Unknown symbol b43_pio_init
b43: Unknown symbol b43_pio_tx_suspend
b43: Unknown symbol b43_pio_tx_resume
b43: Unknown symbol b43_pcmcia_exit
b43: Unknown symbol b43_pcmcia_init
b43: Unknown symbol b43_pio_get_tx_stats
b43: Unknown symbol b43_pio_stop
b43: Unknown symbol b43_pio_tx
b43: Unknown symbol b43_pio_rx
b43: Unknown symbol b43_pio_handle_txstatus

Help mi ....

Post #5
SaTaN
21 Sep 2009, 16:29

It's a bug in the patch.

I will try to correct that.

Post #6
dstyle
24 Sep 2009, 02:18

Here is a patch Satan sent me with email

http://jw.reflektor.cz/openwrtr17570_b4 … io-1.patch

it should fix the issue mentioned by Irek

> do NOT (try to) apply this patch on openwrt itself. Copy it to
> .../openwrt/package/mac80211/patches
>
> then the module should load.


With fideling a bit with this patch i got the trunk compiled. Atm i did not run the created firmware on the router. My edited version is there: http://jw.reflektor.cz/openwrtr17570_b4 … patch_test . If you have some problem with the original patch then try ths version. rename/move it to .../openwrt/package/mac80211/patches

(Last edited by dstyle on 24 Sep 2009, 02:19)

Post #7
marioz
29 Sep 2009, 18:16

Hi

When I try to apply the patch i have an error(?):

patch -p1 --dry-run < ../openwrt_wl520gu.patch
patching file linux/brcm47xx/patches-2.6.28/903-ssb-additional_sprom_vars_from_cfe.patch
patching file linux/brcm47xx/patches-2.6.28/904-ssb-patch-main.patch
patching file linux/brcm47xx/patches-2.6.28/902-ssb-add-pmu-funcs.patch
patching file linux/brcm47xx/patches-2.6.28/901-ssb-hdrs-update.patch
The next patch would delete the file mac80211/patches/001-speedup_build.patch,
which does not exist!  Assume -R? [n]

I'm get 17570 revision from svn:

 svn co svn://svn.openwrt.org/openwrt/trunk/ -r 17570 .

What I should to do?

(Last edited by marioz on 29 Sep 2009, 18:18)

Post #8
Irek
30 Sep 2009, 09:15

Hi

patch -p0 --dry-run < ../openwrt_wl520gu.patch
Post #9
marioz
30 Sep 2009, 19:01

It works very well (wifi).

Thanks.

Post #10
kofec
16 Oct 2009, 21:40

Update:

Regarding enable wifi in DIR-320 you can find hear
https://dev.openwrt.org/ticket/5978#comment:5


Hi,
I have DIR-320, it is very similar to wl-520gu. I tried these changes but it doesn't work (log below). I have a question; you disable LP drivers (# CONFIG_B43_PHY_LP=y) in config.mk but modified *lp.c files. Can someone explein me this.

BusyBox v1.14.4 (2009-10-16 18:54:01 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 KAMIKAZE (bleeding edge, r18050) ------------------
  * 10 oz Vodka       Shake well with ice and strain
  * 10 oz Triple sec  mixture into 10 shot glasses.
  * 10 oz lime juice  Salute!
 ---------------------------------------------------
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/# dmesg
Linux version 2.6.30.8 (kofec@kofec-desktop) (gcc version 4.1.2) #3 Fri Oct 16 22:21:29 CEST 2009
CPU revision is: 00029029 (Broadcom BCM3302)
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x14, vendor 0x4243)
ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x09, vendor 0x4243)
ssb: Core 2 found: MIPS 3302 (cc 0x816, rev 0x08, vendor 0x4243)
ssb: Core 3 found: USB 2.0 Host (cc 0x819, rev 0x02, vendor 0x4243)
ssb: Core 4 found: MEMC SDRAM (cc 0x80F, rev 0x04, vendor 0x4243)
ssb: Core 5 found: IEEE 802.11 (cc 0x812, rev 0x0D, vendor 0x4243)
ssb: Core 6 found: Roboswitch (cc 0x81C, rev 0x02, vendor 0x4243)
ssb: Found rev 0 PMU (capabilities 0x04A63400)
ssb: Initializing MIPS core...
ssb: core 0x0800, irq : 2(S)  3* 4  5  6  D  I
ssb: core 0x0806, irq : 2(S)  3  4* 5  6  D  I
ssb: core 0x0816, irq : 2(S)  3  4  5* 6  D  I
ssb: core 0x0819, irq : 2(S)  3  4  5  6* D  I
ssb: core 0x080f, irq : 2(S)  3  4  5  6  D  I*
ssb: core 0x0812, irq : 2(S)* 3  4  5  6  D  I
ssb: core 0x081c, irq : 2(S)  3  4  5  6  D  I*
ssb: set_irq: core 0x0806, irq 4 => 4
ssb: set_irq: core 0x0816, irq 5 => 2
ssb: set_irq: core 0x0812, irq 2 => 5
ssb: after irq reconfiguration
ssb: core 0x0800, irq : 2(S)  3* 4  5  6  D  I
ssb: core 0x0806, irq : 2(S)  3  4* 5  6  D  I
ssb: core 0x0816, irq : 2(S)* 3  4  5  6  D  I
ssb: core 0x0819, irq : 2(S)  3  4  5  6* D  I
ssb: core 0x080f, irq : 2(S)  3  4  5  6  D  I*
ssb: core 0x0812, irq : 2(S)  3  4  5* 6  D  I
ssb: core 0x081c, irq : 2(S)  3  4  5  6  D  I*
ssb: Sonics Silicon Backplane found at address 0x18000000
Serial init done.
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
On node 0 totalpages: 8192
free_area_init_node: node 0, pgdat 80273770, node_mem_map 81000000
  Normal zone: 64 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 8128 pages, LIFO batch:0
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
NR_IRQS:128
PID hash table entries: 128 (order: 7, 512 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29712k/32768k available (2111k kernel code, 3056k reserved, 398k data, 128k init, 0k highmem)
Calibrating delay loop... 239.10 BogoMIPS (lpj=478208)
Mount-cache hash table entries: 512
net_namespace: 528 bytes
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switched to high resolution mode on CPU 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  Š 2001-2006 Red Hat, Inc.
msgmni has been set to 58
alg: No test for lzma (lzma-generic)
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:90:4c:c0:00:00
flash init: 0x1c000000 0x02000000
Physically mapped flash: Found 1 x16 devices at 0x0 in 8-bit bank
Physically mapped flash: Found an alias at 0x400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0xc00000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1c00000 for the chip at 0x0
 Amd/Fujitsu Extended Query Table at 0x0040
Physically mapped flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x400000 at 0x1fc00000
bootloader size: 262144
Updating TRX offsets and length:
old trx = [0x0000001c, 0x0000090c, 0x000d1000], len=0x002b1000 crc32=0x82d8ee9e
new trx = [0x0000001c, 0x0000090c, 0x000d1000], len=0x000d1000 crc32=0x9e0e2adc
Done
Creating 4 MTD partitions on "Physically mapped flash":
0x000000000000-0x000000040000 : "cfe"
0x000000040000-0x0000003f0000 : "linux"
0x000000111000-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=2E0000, len=110000
0x0000002e0000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "nvram"
BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 128k freed
Please be patient, while OpenWrt loads ...
diag: Detected 'D-Link DIR-320'
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
roboswitch: Probing device eth0: found!
b44: eth0: powering down PHY
mini_fo: using base directory: /
mini_fo: using storage directory: /tmp/root
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
device eth0.0 entered promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0.0) entering forwarding state
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
        (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
        (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
        (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
b43-phy0: Broadcom 5354 WLAN found (core revision 13)
b43-phy0 debug: Found PHY: Analog 6, Type 5, Revision 0
b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2062, Revision 1
phy0: Selected rate control algorithm 'minstrel'
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
Broadcom 43xx-legacy driver loaded [ Features: PLID, Firmware-ID: FW10 ]
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
Driver 'sd' needs updating - please use bus_type methods
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
nf_conntrack version 0.5.0 (512 buckets, 2048 max)
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd ssb0:1: SSB OHCI Controller
ohci_hcd ssb0:1: new USB bus registered, assigned bus number 1
ohci_hcd ssb0:1: irq 6, io mem 0x18003000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd ssb0:1: SSB EHCI Controller
ohci_hcd ssb0:1: new USB bus registered, assigned bus number 2
ohci_hcd ssb0:1: irq 6, io mem 0x18003800
ohci_hcd ssb0:1: USB 0.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 2-1: new high speed USB device using ohci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi 0:0:0:0: Direct-Access     starline Flash Disk       5.00 PQ: 0 ANSI: 2
usb-storage: device scan complete
sd 0:0:0:0: [sda] 128576 512-byte hardware sectors: (65.8 MB/62.7 MiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 0b 00 00 08
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk
EXT2-fs warning (device sda1): ext2_fill_super: mounting ext3 filesystem as ext2
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
jffs2_build_filesystem(): unlocking the mtd device... done.
jffs2_build_filesystem(): erasing all blocks after the end marker... done.
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs

(Last edited by kofec on 10 Nov 2009, 10:07)

Post #11
anne22
15 Nov 2009, 09:46

hi aan alle forumers van deze draad ... Ik ben een newbie hier. Ik zou graag wat vrienden ontmoeten en plezier hebben!
my notebook was okay at first but as time passes by this stuff becomes so annoying. first, the wifi is no longer functioning then now i can no longer open it. what shall i do. this is just 4 months old to me

Post #12
Martin2789
15 Nov 2009, 11:42
anne22 wrote:

hi aan alle forumers van deze draad ... Ik ben een newbie hier. Ik zou graag wat vrienden ontmoeten en plezier hebben!
my notebook was okay at first but as time passes by this stuff becomes so annoying. first, the wifi is no longer functioning then now i can no longer open it. what shall i do. this is just 4 months old to me

Sorry! This topic is not about a laptop. It is about, Wlan driver for a wlan router.....
What do you do here? It sounds like a trouble with your WiFi, but not a trouble with openWRT.
Martin

The discussion might have continued from here.