Hi I have cleared my sagem but not right where the serial port. Where is RX and TX?
http://www.3gspain.org/sagem.jpg
(Last edited by juander on 17 Sep 2009, 23:04)
Topic: [Photo Sagem 2404 motherboard] help me find the serial port?
The content of this topic has been archived on 21 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.
Page 1 of 1
You'll have to solder a four pin header in the space right below the ethernet switch.
The pin nearest to the switch looks like ground, then probably tx and rx (going down).
That's what I figured but there are a number of components without soldering just below, do not influence?
This router also has usb?
(Last edited by juander on 18 Sep 2009, 09:50)
I have seen two possible RX and TX, a default one is at 0V and the other at 2.8V, that you think?
If I convert the signals between router and PC with a MAX232, does it break?
(Last edited by juander on 19 Sep 2009, 10:44)
Thank, to connect your PC to the router can I use MAX232?
It is better to use MAX3232, or mobile phone datacable like Nokia DKU-5. I am using Siemens mobile datacable with Prolific PL2303 chip.
How upload the firmware? How is the cable connected properly?
It is not the same hardware, but it can help you to understand how install or use the serial cable, maybe the firmware as well.
http://www.mightyohm.com/blog/2008/10/b … -wl-520gu/
juander, the pinouts is (bottom) gnd - tx - rx - vcc (top)
Original FIrmware Serial Output:
Sagem CFE version: 3.13.5
Build Date: Mon May 14 17:56:09 CST 2007
(shenmc@svr1.sagemharbournetworks.com)
Copyright (C) 2005-2006 Sagem communication.
Boot Address 0xbfc00000
Initializing Arena.
Initializing Devices.
Parallel flash device: name SST39VF3201, id 0x235b, size 4096KB
Enter readNvramData(CFE)
Enter kerSysNvRamGet(CFE)
kerSysNvRamGet(CFE) Mac address:00:19:4b:b4:dd:aa, BoardId=F@ST2404
Enter readNvramData(CFE)
Enter kerSysNvRamGet(CFE)
kerSysNvRamGet(CFE) Mac address:00:19:4b:b4:dd:aa, BoardId=F@ST2404
Enter readNvramData(CFE)
Enter kerSysNvRamGet(CFE)
kerSysNvRamGet(CFE) Mac address:00:19:4b:b4:dd:aa, BoardId=F@ST2404
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory: 16777216 bytes (16MB)
Total memory used by CFE: 0x80401000 - 0x80528470 (1209456)
Initialized Data: 0x8041EAE0 - 0x80421AB0 (12240)
BSS Area: 0x80421AB0 - 0x80426470 (18880)
Local Heap: 0x80426470 - 0x80526470 (1048576)
Stack Area: 0x80526470 - 0x80528470 (8192)
Text (code) segment: 0x80401000 - 0x8041EAD8 (121560)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Enter readNvramData(CFE)
Enter kerSysNvRamGet(CFE)
kerSysNvRamGet(CFE) Mac address:00:19:4b:b4:dd:aa, BoardId=F@ST2404
Enter readNvramData(CFE)
Enter kerSysNvRamGet(CFE)
kerSysNvRamGet(CFE) Mac address:00:19:4b:b4:dd:aa, BoardId=F@ST2404
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.28
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id Name : F@ST2404
Psi size in KB : 24
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:19:4b:b4:dd:aa
Ethernet PHY Type : Internal
Memory size in MB : 16
CMT Thread Number : 0
Customer Name :SAGM(default)
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x801c6018
Decompression OK!
Entry at 0x801c6018
Closing network.
Starting program at 0x801c6018
Linux version 2.6.8.1 (chenc@svr1.sagem-szn.com) (gcc version 3.4.2) #1
Wed Jun8
Parallel flash device: name SST39VF3201, id 0x235b, size 4096KB
Total Flash size: 4096K with 1024 sectors
fInfo.flash_scratch_pad_start_blk = 1016
fInfo.flash_scratch_pad_number_blk = 2
fInfo.flash_scratch_pad_length = 0x2000
fInfo.flash_scratch_pad_blk_offset = 0x0
fInfo.flash_nvram_start_blk = 0
fInfo.flash_nvram_blk_offset = 0x580
fInfo.flash_nvram_number_blk = 1
fInfo.flash_persistent_start_blk = 1018
fInfo.flash_persistent_blk_offset = 0x0
fInfo.flash_persistent_number_blk = 6
backup_start_blk = 1010
backup_blk_offset = 0x0
backup_number_blk = 6
backup_length = 24576
psi startAddr = bfffa000
sp startAddr = bfff8000
backup startAddr = bfff2000
F@ST2404 prom init
CPU revision is: 00029107
Determined physical RAM map:
memory: 00fa0000 @ 00000000 (usable)
On node 0 totalpages: 4000
DMA zone: 4000 pages, LIFO batch:1
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16
bytes.
Primary data cache 8kB 2-way, linesize 16 bytes.
PID hash table entries: 64 (order 6: 512 bytes)
Using 128.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 13816k/16000k available (1515k kernel code, 2164k reserved, 233k
data, )
Calibrating delay loop... 254.77 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction... unavailable.
NET: Registered protocol family 16
Can't analyze prologue code at 80189494
usbcore: registered new driver hub
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v1.0
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 20, pci mem c0000b00
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
brcmboard: brcm_board_init entry
RestoreMacFilter: Button GPIO 0x21 is enabled
RestoreMacFilter: Button Interrupt 0x1 is enabled
RestoreMacFilter: Interrupt mapping OK
Serial: BCM63XX driver $Revision: 1.3 $
ttyS0 at MMIO 0xfffe0300 (irq = 10) is a BCM63XX
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
********* ip_rt_init ************
sizeof(struct rtable)=244
ip_rt_max_size=2048, rt_hash_mask=511, ipv4_dst_ops.gc_thresh=512,
ip_rt_gc_interval=12000, rt_secret_rebuild=120000
TCP: Hash tables configured (established 512 bind 1024)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 72k freed
init started: BusyBox v1.00 (2008.06.25-10:09+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
mount: Mounting tmpfs on /tmp failed: No such file
BusyBox v1.00 (2008.06.25-10:09+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6348B0 Ethernet Network Device v0.3 Jun 25 2008 18:01:31
Config Ethernet Switch Through SPI Slave Select 0
dgasp: kerSysRegisterDyingGaspHandler: eth0 registered
eth0: MAC Address: 00:19:4B:B4:DD:AA
Cfm wathcer has been setup!
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 00:19:4B:B4:DD:AB
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.150.10.15.cpe2.2
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
eth0 Link UP.
Cfm has been started to initiate!
Read Flash: part=[PERSISTENT]
Read Flash: part=[PERSISTENT]
PSI has been initiated successfully!
BcmAdsl_Initialize=0xC006D928, g_pFnNotifyCallback=0xC0088D14
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
pSdramPHY=0xA0FFFFF8, 0x28041 0x9689ACE8
AdslCoreHwReset: AdslOemDataAddr = 0xA0FFBB64
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
Read Flash: part=[FACTORYINFO]
Enter kerSysFactoryInfoGet: strLen[256],offset[0]
FactoryInfo[1-10]=[??????????]
ATM proc init !!!
ATM Config Management initiated successfully!
Security configuration management initiated successfully!
==> Software Version: 3.24a4 <==
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
Setting SSID "Sagem"
Setting SSID "Guest"
Setting country code using abbreviation: "FR"
wlctl band b run 0 time!
wlctl band b run 0 time!
channel 11 selected
device wl0 entered promiscuous mode
br0: port 2(wl0) entering learning state
br0: topology change detected, propagating
br0: port 2(wl0) entering forwarding state
device wl0.1 entered promiscuous mode
br0: port 3(wl0.1) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0.1) entering forwarding state
EngDbg:- PSI Retrieve Status for PortMirrorStatus = 3
EngDbg:- In Effect Port Mirror Cfg
ENGDBG :- In Effect Port Mirroring, status = 0 count = 0
Read Flash: part=[SCRATCH_PAD]
Read Flash: part=[SCRATCH_PAD]
Network initiated successfully!
Web Server initiated successfully!
Read Flash: part=[SCRATCH_PAD]
Cfm initiated successfully!
No POSTINIT command need excuting
Admin URL is blank, then don't start RemoteAutoUpgradeThread
========>Load the wireless_reload_monitor thread<=======
nat_cache: Unknown symbol invert_tuplepr
nat_cache: Unknown symbol ip_ct_find_helper
nat_cache: Unknown symbol ip_ct_refresh
insmod: cannot insert
`/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/broadcom/s
--->syslog_options_up: blocksite unloged!
nat_cache: Unknown symbol invert_tuplepr
nat_cache: Unknown symbol ip_ct_find_helper
nat_cache: Unknown symbol ip_ct_refresh
insmod: cannot insert
`/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/broadcom/s
Read Flash: part=[FACTORYINFO]
Enter kerSysFactoryInfoGet: strLen[1024],offset[0]
FactoryInfo[1-10]=[??????????]is there any pre-built image ? Because the latest f@ast2404-cfe, from 8.09 rc2 gets partition error...
thx
Has anyone succeeded in porting openwrt to the sagem fast 2404 / 2504 / 2604 ? if so, how? probably my isp will be giving me one soon.
flash is unusable... so no filesystem 
But there must be some way, why doesn't the bootloader load the image? wrong headers/checksums? some compression algorithms we're not using? How about replacing the bootloader?
naplam wrote:
But there must be some way, why doesn't the bootloader load the image? wrong headers/checksums? some compression algorithms we're not using? How about replacing the bootloader?
no, no.. the bootloader does load the image.
see bug tracker
Ok, so we just have to figure out the original firmware organization in the flash memory and mimic that, right? our kernel is being loaded but the squashfs partition is not the right place/the flash is not correctly partitioned, is that it?
(Last edited by naplam on 16 Jan 2010, 00:31)
naplam wrote:
Ok, so we just have to figure out the original firmware organization in the flash memory and mimic that, right? our kernel is being loaded but the squashfs partition is not the right place/the flash is not correctly partitioned, is that it?
exacto 
cat /proc/mtd
dev: size erasesize name
mtd0: 002d1000 00001000 "Physically mapped flash"tehere's only one partition mtd0 ...
these days i've been flashing an ar7 so i know mtd partitions may be redefined... but ¿how can this be done in cfe? ¿deosn't the bin image redefine the map?
(Last edited by DeerHunter on 16 Jan 2010, 00:55)
someone got it working already a year ago:
https://forum.openwrt.org/viewtopic.php … 246#p76246
but he doesn't give much details i think hmm
DeerHunter, how do you log in with the original firmware? i have a tacky configuration interface in the sagem 2604 in telnet and ssh, not a shell. Also, mtdX are not mentioned in the system logs, another naming is used ("read flash: part [factory] things like that instead of mtd0 or 1 o2 whatever, you can see it in the log.
edit: i see your 2404 log is almost identical
edit: i guess you're getting a shell from the serial console 
edit(2): i can get a shell by typing sh in the tacky menu instead of an option number
edit(3): some info:
# df
Filesystem 1k-blocks Used Available Use% Mounted on
/dev/mtdblock0 3200 3200 0 100% /
tmpfs 320 136 184 43% /var
tmpfs 16 0 16 0% /mnt
# cat /proc/mtd
dev: size erasesize name
mtd0: 00313000 00001000 "Physically mapped flash"
# cat cpuinfo
system type : F@ST2604
processor : 0
cpu model : BCM6348 V0.7
BogoMIPS : 254.77
wait instruction : no
microsecond timers : yes
tlb_entries : 32
extra interrupt vector : yes
hardware watchpoint : no
VCED exceptions : not available
VCEI exceptions : not availableI post it here in case it can help anyone with a 2404 or 2604 and similar hardware.
System Log:
date facility severity message
Jan 1 00:00:30 user warn kernel: backup_number_blk = 6
Jan 1 00:00:30 user warn kernel: backup_length = 24576
Jan 1 00:00:30 user warn kernel:
Jan 1 00:00:30 user warn kernel: psi startAddr = bfffa000
Jan 1 00:00:30 user warn kernel: systemini startAddr = bfff9000
Jan 1 00:00:30 user warn kernel: sp startAddr = bfff8000
Jan 1 00:00:30 user warn kernel: backup startAddr = bfff2000
Jan 1 00:00:30 user warn kernel:
Jan 1 00:00:30 user warn kernel: F@ST2604 prom init
Jan 1 00:00:30 user warn kernel: CPU revision is: 00029107
Jan 1 00:00:30 user warn kernel: Determined physical RAM map:
Jan 1 00:00:30 user warn kernel: memory: 00fa0000 @ 00000000 (usable)
Jan 1 00:00:30 user debug kernel: On node 0 totalpages: 4000
Jan 1 00:00:30 user debug kernel: DMA zone: 4000 pages, LIFO batch:1
Jan 1 00:00:30 user debug kernel: Normal zone: 0 pages, LIFO batch:1
Jan 1 00:00:30 user debug kernel: HighMem zone: 0 pages, LIFO batch:1
Jan 1 00:00:30 user warn kernel: Built 1 zonelists
Jan 1 00:00:30 user warn kernel: Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
Jan 1 00:00:30 user warn kernel: brcm mips: enabling icache and dcache...
Jan 1 00:00:30 user warn kernel: Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Jan 1 00:00:30 user warn kernel: Primary data cache 8kB 2-way, linesize 16 bytes.
Jan 1 00:00:30 user warn kernel: PID hash table entries: 64 (order 6: 512 bytes)
Jan 1 00:00:30 user warn kernel: Using 128.000 MHz high precision timer.
Jan 1 00:00:30 user warn kernel: Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan 1 00:00:30 user warn kernel: Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Jan 1 00:00:30 user info kernel: Memory: 13816k/16000k available (1516k kernel code, 2164k reserved, 232k data, 72k init, 0k highmem)
Jan 1 00:00:30 user warn kernel: Calibrating delay loop... 254.77 BogoMIPS
Jan 1 00:00:30 user warn kernel: Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Jan 1 00:00:30 user warn kernel: Checking for 'wait' instruction... unavailable.
Jan 1 00:00:30 user info kernel: NET: Registered protocol family 16
Jan 1 00:00:30 user warn kernel: Can't analyze prologue code at 80189904
Jan 1 00:00:30 user info kernel: usbcore: registered new driver hub
Jan 1 00:00:30 user info kernel: Initializing Cryptographic API
Jan 1 00:00:30 user info kernel: PPP generic driver version 2.4.2
Jan 1 00:00:30 user info kernel: NET: Registered protocol family 24
Jan 1 00:00:30 user warn kernel: Using noop io scheduler
Jan 1 00:00:30 user warn kernel: bcm963xx_mtd driver v1.0
Jan 1 00:00:30 user debug kernel: ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Jan 1 00:00:30 user debug kernel: ohci_hcd: block sizes: ed 64 td 64
Jan 1 00:00:30 user warn kernel: PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
Jan 1 00:00:30 user info kernel: ohci_hcd 0000:00:09.0: OHCI Host Controller
Jan 1 00:00:30 user debug kernel: PCI: Setting latency timer of device 0000:00:09.0 to 64
Jan 1 00:00:30 user info kernel: ohci_hcd 0000:00:09.0: irq 20, pci mem c0000b00
Jan 1 00:00:30 user info kernel: ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 1
Jan 1 00:00:30 user info kernel: hub 1-0:1.0: USB hub found
Jan 1 00:00:30 user info kernel: hub 1-0:1.0: 2 ports detected
Jan 1 00:00:30 user info kernel: usbcore: registered new driver usblp
Jan 1 00:00:30 user info kernel: drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Jan 1 00:00:30 user warn kernel: brcmboard: brcm_board_init entry
Jan 1 00:00:30 user warn kernel: RestoreMacFilter: Button GPIO 0x21 is enabled
Jan 1 00:00:30 user warn kernel: RestoreMacFilter: Button Interrupt 0x1 is enabled
Jan 1 00:00:30 user warn kernel: RestoreMacFilter: Interrupt mapping OK
Jan 1 00:00:30 user info kernel: Serial: BCM63XX driver $Revision: 1.3 $
Jan 1 00:00:30 user warn kernel: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a BCM63XX
Jan 1 00:00:30 user info kernel: NET: Registered protocol family 2
Jan 1 00:00:30 user info kernel: IP: routing cache hash table of 512 buckets, 4Kbytes
Jan 1 00:00:30 user warn kernel: ********* ip_rt_init ************
Jan 1 00:00:30 user warn kernel: sizeof(struct rtable)=244
Jan 1 00:00:30 user warn kernel: ip_rt_max_size=2048, rt_hash_mask=511, ipv4_dst_ops.gc_thresh=512,
Jan 1 00:00:30 user warn kernel: ip_rt_gc_interval=12000, rt_secret_rebuild=120000
Jan 1 00:00:30 user info kernel: TCP: Hash tables configured (established 512 bind 1024)
Jan 1 00:00:30 user info kernel: Initializing IPsec netlink socket
Jan 1 00:00:30 user info kernel: NET: Registered protocol family 1
Jan 1 00:00:30 user info kernel: NET: Registered protocol family 17
Jan 1 00:00:30 user info kernel: NET: Registered protocol family 15
Jan 1 00:00:30 user notice kernel: Ebtables v2.0 registered
Jan 1 00:00:30 user info kernel: NET: Registered protocol family 8
Jan 1 00:00:30 user info kernel: NET: Registered protocol family 20
Jan 1 00:00:30 user info kernel: 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
Jan 1 00:00:30 user info kernel: All bugs added by David S. Miller <davem@redhat.com>
Jan 1 00:00:30 user warn kernel: VFS: Mounted root (squashfs filesystem) readonly.
Jan 1 00:00:30 user info kernel: Freeing unused kernel memory: 72k freed
Jan 1 00:00:30 user warn kernel: Algorithmics/MIPS FPU Emulator v1.5
Jan 1 00:00:30 user warn kernel: atmapi: module license 'Proprietary' taints kernel.
Jan 1 00:00:30 user warn kernel: adsl: adsl_init entry
Jan 1 00:00:30 user warn kernel: entry
Jan 1 00:00:30 user info kernel: Broadcom BCMPROCFS v1.0 initialized
Jan 1 00:00:30 user warn kernel: Broadcom BCM6348B0 Ethernet Network Device v0.3 Jan 19 2009 17:23:25
Jan 1 00:00:30 user warn kernel: Config Ethernet Switch Through SPI Slave Select 0
Jan 1 00:00:30 user warn kernel: Cfm wathcer has been setup!
Jan 1 00:00:30 user warn kernel: dgasp: kerSysRegisterDyingGaspHandler: eth0 registered
Jan 1 00:00:30 user warn kernel: eth0: MAC Address: 00:26:91:20:84:16
Jan 1 00:00:30 user debug kernel: PCI: Setting latency timer of device 0000:00:01.0 to 64
Jan 1 00:00:30 user warn kernel: PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
Jan 1 00:00:30 user warn kernel: wl: srom not detected, using main memory mapped srom info (wombo board)
Jan 1 00:00:30 user warn kernel: wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
Jan 1 00:00:30 user warn kernel: wl0: MAC Address: 00:26:91:20:84:17
Jan 1 00:00:30 user warn kernel: wl0: Broadcom BCM4318 802.11 Wireless Controller 4.174.64.18.cpe1.0
Jan 1 00:00:30 user warn kernel: dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
Jan 1 00:00:30 user warn kernel: Cfm has been started to initiate!
Jan 1 00:00:30 user warn kernel: Read Flash: part=[PERSISTENT]
Jan 1 00:00:30 user warn kernel: Read Flash: part=[PERSISTENT]
Jan 1 00:00:30 user warn kernel: PSI has been initiated successfully!
Jan 1 00:00:30 user warn kernel: BcmAdsl_Initialize=0xC0070958, g_pFnNotifyCallback=0xC008E3C4
Jan 1 00:00:30 user warn kernel: AnnexCParam=0x7FFF7858 AnnexAParam=0x00000980 adsl2=0x00000000
Jan 1 00:00:30 user warn kernel: pSdramPHY=0xA0FFFFF8, 0x1B7966 0xDEADBEEF
Jan 1 00:00:30 user warn kernel: AdslCoreSharedMemInit: shareMemAvailable=21568
Jan 1 00:00:30 user warn kernel: AdslCoreHwReset: AdslOemDataAddr = 0xA0FEF9FC
Jan 1 00:00:30 user warn kernel: AnnexCParam=0x7FFF7858 AnnexAParam=0x00000980 adsl2=0x00000000
Jan 1 00:00:30 user warn kernel: dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
Jan 1 00:00:30 user warn kernel: ATM proc init !!!
Jan 1 00:00:30 user warn kernel: ATM Config Management initiated successfully!
Jan 1 00:00:30 user warn kernel: ip_tables: (C) 2000-2002 Netfilter core team
Jan 1 00:00:30 user warn kernel: ip_conntrack version 2.1 (125 buckets, 0 max) - 368 bytes per conntrack
Jan 1 00:00:30 user warn kernel: ip_conntrack_pptp version 2.1 loaded
Jan 1 00:00:30 user warn kernel: ip_nat_pptp version 2.0 loaded
Jan 1 00:00:30 user warn kernel: ip_conntrack_h323: init
Jan 1 00:00:30 user warn kernel: ip_nat_h323: initialize the module!
Jan 1 00:00:30 user warn kernel: BRCM NAT Caching v0.1 Nov 18 2006 14:56:48
Jan 1 00:00:30 user warn kernel: BRCM NAT Cache: Hooking hit function @ c0058c64
Jan 1 00:00:30 user warn kernel: ip_conntrack_rtsp v0.01 loading
Jan 1 00:00:30 user warn kernel: ip_nat_rtsp v0.01 loading
Jan 1 00:00:30 user warn kernel: Security configuration management initiated successfully!
Jan 1 00:00:30 user warn kernel: Read Flash: part=[FACTORYINFO]
Jan 1 00:00:30 user warn kernel: Enter kerSysFactoryInfoGet: strLen[64],offset[0]
Jan 1 00:00:30 user warn kernel: FactoryInfo[1-10]=[LK93211363]
Jan 1 00:00:30 user info kernel: device eth0 entered promiscuous mode
Jan 1 00:00:30 user info kernel: br0: port 1(eth0) entering learning state
Jan 1 00:00:30 user info kernel: br0: topology change detected, propagating
Jan 1 00:00:30 user info kernel: br0: port 1(eth0) entering forwarding state
Jan 1 00:00:30 user info kernel: device wl0 entered promiscuous mode
Jan 1 00:00:30 user info kernel: br0: port 2(wl0) entering learning state
Jan 1 00:00:30 user info kernel: br0: topology change detected, propagating
Jan 1 00:00:30 user info kernel: br0: port 2(wl0) entering forwarding state
Jan 1 00:00:30 user info kernel: device wl0.1 entered promiscuous mode
Jan 1 00:00:30 user info kernel: br0: port 3(wl0.1) entering learning state
Jan 1 00:00:30 user info kernel: br0: topology change detected, propagating
Jan 1 00:00:30 user info kernel: br0: port 3(wl0.1) entering forwarding state
Jan 1 00:00:30 user warn kernel: hlist_add_head_rcu=[2:26:91:20:84:17]-----------------
Jan 1 00:00:30 user warn kernel: source->dev->name=[wl0] ,is_local=[0]
Jan 1 00:00:30 user info kernel: device eth0 left promiscuous mode
Jan 1 00:00:30 user info kernel: br0: port 1(eth0) entering disabled state
Jan 1 00:00:30 user info kernel: device eth0 entered promiscuous mode
Jan 1 00:00:30 user info kernel: br0: port 1(eth0) entering learning state
Jan 1 00:00:30 user info kernel: br0: topology change detected, propagating
Jan 1 00:00:30 user info kernel: br0: port 1(eth0) entering forwarding state
Jan 1 00:00:30 user info kernel: device wl0 left promiscuous mode
Jan 1 00:00:30 user info kernel: br0: port 2(wl0) entering disabled state
Jan 1 00:00:30 user info kernel: device wl0 entered promiscuous mode
Jan 1 00:00:30 user info kernel: br0: port 2(wl0) entering learning state
Jan 1 00:00:30 user info kernel: br0: topology change detected, propagating
Jan 1 00:00:30 user info kernel: br0: port 2(wl0) entering forwarding state
Jan 1 00:00:30 user warn kernel: hlist_add_head_rcu=[2:26:91:20:84:17]-----------------
Jan 1 00:00:30 user warn kernel: source->dev->name=[wl0] ,is_local=[0]
Jan 1 00:00:30 user info kernel: device wl0.1 left promiscuous mode
Jan 1 00:00:30 user info kernel: br0: port 3(wl0.1) entering disabled state
Jan 1 00:00:30 user info kernel: device wl0.1 entered promiscuous mode
Jan 1 00:00:30 user info kernel: br0: port 3(wl0.1) entering learning state
Jan 1 00:00:30 user info kernel: br0: topology change detected, propagating
Jan 1 00:00:30 user info kernel: br0: port 3(wl0.1) entering forwarding state
Jan 1 00:00:30 user warn kernel: hlist_add_head_rcu=[0:12:17:41:db:fb]-----------------
Jan 1 00:00:30 user warn kernel: source->dev->name=[wl0] ,is_local=[0]
Jan 1 00:00:30 user warn kernel: Read Flash: part=[SCRATCH_PAD]
Jan 1 00:00:30 user warn kernel: Read Flash: part=[SCRATCH_PAD]
Jan 1 00:00:30 user warn kernel: Network initiated successfully!
Jan 1 00:00:31 user warn kernel: Web Server initiated successfully!
Jan 1 00:00:31 user warn kernel: Read Flash: part=[SCRATCH_PAD]
Jan 1 00:00:31 user warn kernel: Read Flash: part=[SYSTEM_INI]
Jan 1 00:00:31 user warn kernel: Enter kerSysSystemIniGet: strLen[4096],offset[0],fInfo.flash_system_ini_blk_offset=[0]
Jan 1 00:00:31 user warn kernel: SystemIni[1-10]=[[quickSetu]
Jan 1 00:00:31 user debug syslog: Remote upgrade: Admin URL is blank, then don't start RemoteAutoUpgradeThread
Jan 1 00:00:33 daemon info dnsmasq[534]: started, version 2.23 cachesize 150
Jan 1 00:00:33 daemon info dnsmasq[534]: compile time options: no-IPv6 GNU-getopt ISC-leasefile no-DBus
Jan 1 00:00:33 daemon warn dnsmasq[534]: running as root
Jan 1 00:00:33 daemon info dnsmasq[534]: read /etc/hosts - 1 addresses
Jan 1 00:00:33 daemon warn dnsmasq[534]: failed to access /etc/resolv.conf: No such file or directory
Jan 1 00:00:34 daemon info dnsmasq[544]: started, version 2.23 cachesize 150
Jan 1 00:00:34 daemon info dnsmasq[544]: compile time options: no-IPv6 GNU-getopt ISC-leasefile no-DBus
Jan 1 00:00:34 daemon warn dnsmasq[544]: running as root
Jan 1 00:00:34 daemon info dnsmasq[544]: read /etc/hosts - 1 addresses
Jan 1 00:00:34 daemon warn dnsmasq[544]: failed to access /etc/resolv.conf: No such file or directory
Jan 1 00:00:34 user info kernel: br0: port 1(eth0) entering disabled state
Jan 1 00:00:35 user warn kernel: Cfm initiated successfully!
Jan 1 00:00:50 user warn kernel: Read Flash: part=[FACTORYINFO]
Jan 1 00:00:50 user warn kernel: Enter kerSysFactoryInfoGet: strLen[1024],offset[0]
Jan 1 00:00:50 user warn kernel: FactoryInfo[1-10]=[LK93211363]
Jan 1 00:00:50 user warn kernel: Read Flash: part=[PERSISTENT]
Jan 1 00:00:50 user warn kernel: Read Flash: part=[BACKUP]
Jan 1 00:00:50 user warn kernel: Enter kerSysBackupGet: strLen[24576],offset[0],fInfo.flash_backup_blk_offset=[0]
Jan 1 00:00:50 user warn kernel: Backup[1-10]=[<psitree>
Jan 1 00:00:50 user warn kernel: ]
Jan 1 00:00:50 user warn kernel: Enter kerSysScratchPadBlock
Jan 1 00:00:50 user warn kernel: read buffer len is: 4096
Jan 1 00:00:50 user warn kernel: Read Flash: part=[SYSTEM_INI]
Jan 1 00:00:50 user warn kernel: Enter kerSysSystemIniGet: strLen[4096],offset[0],fInfo.flash_system_ini_blk_offset=[0]
Jan 1 00:00:50 user warn kernel: SystemIni[1-10]=[[quickSetu]
dmesg info:
et = 0x0
system_ini_start_blk = 1017
system_ini_number_blk = 1
system_ini_blk_offset = 0x0
system_ini_length = 4096
fInfo.flash_nvram_start_blk = 0
fInfo.flash_nvram_blk_offset = 0x580
fInfo.flash_nvram_number_blk = 1
fInfo.flash_persistent_start_blk = 1018
fInfo.flash_persistent_blk_offset = 0x0
fInfo.flash_persistent_number_blk = 6
backup_start_blk = 1010
backup_blk_offset = 0x0
backup_number_blk = 6
backup_length = 24576
psi startAddr = bfffa000
systemini startAddr = bfff9000
sp startAddr = bfff8000
backup startAddr = bfff2000
F@ST2604 prom init
CPU revision is: 00029107
Determined physical RAM map:
memory: 00fa0000 @ 00000000 (usable)
On node 0 totalpages: 4000
DMA zone: 4000 pages, LIFO batch:1
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 8kB 2-way, linesize 16 bytes.
PID hash table entries: 64 (order 6: 512 bytes)
Using 128.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 13816k/16000k available (1516k kernel code, 2164k reserved, 232k data, 72k init, 0k highmem)
Calibrating delay loop... 254.77 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction... unavailable.
NET: Registered protocol family 16
Can't analyze prologue code at 80189904
usbcore: registered new driver hub
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v1.0
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 20, pci mem c0000b00
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
brcmboard: brcm_board_init entry
RestoreMacFilter: Button GPIO 0x21 is enabled
RestoreMacFilter: Button Interrupt 0x1 is enabled
RestoreMacFilter: Interrupt mapping OK
Serial: BCM63XX driver $Revision: 1.3 $
ttyS0 at MMIO 0xfffe0300 (irq = 10) is a BCM63XX
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
********* ip_rt_init ************
sizeof(struct rtable)=244
ip_rt_max_size=2048, rt_hash_mask=511, ipv4_dst_ops.gc_thresh=512,
ip_rt_gc_interval=12000, rt_secret_rebuild=120000
TCP: Hash tables configured (established 512 bind 1024)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 72k freed
Algorithmics/MIPS FPU Emulator v1.5
atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6348B0 Ethernet Network Device v0.3 Jan 19 2009 17:23:25
Config Ethernet Switch Through SPI Slave Select 0
Cfm wathcer has been setup!
dgasp: kerSysRegisterDyingGaspHandler: eth0 registered
eth0: MAC Address: 00:26:91:20:84:16
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 00:26:91:20:84:17
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.174.64.18.cpe1.0
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
Cfm has been started to initiate!
Read Flash: part=[PERSISTENT]
Read Flash: part=[PERSISTENT]
PSI has been initiated successfully!
BcmAdsl_Initialize=0xC0070958, g_pFnNotifyCallback=0xC008E3C4
AnnexCParam=0x7FFF7858 AnnexAParam=0x00000980 adsl2=0x00000000
pSdramPHY=0xA0FFFFF8, 0x1B7966 0xDEADBEEF
AdslCoreSharedMemInit: shareMemAvailable=21568
AdslCoreHwReset: AdslOemDataAddr = 0xA0FEF9FC
AnnexCParam=0x7FFF7858 AnnexAParam=0x00000980 adsl2=0x00000000
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
ATM proc init !!!
ATM Config Management initiated successfully!
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (125 buckets, 0 max) - 368 bytes per conntrack
ip_conntrack_pptp version 2.1 loaded
ip_nat_pptp version 2.0 loaded
ip_conntrack_h323: init
ip_nat_h323: initialize the module!
BRCM NAT Caching v0.1 Nov 18 2006 14:56:48
BRCM NAT Cache: Hooking hit function @ c0058c64
ip_conntrack_rtsp v0.01 loading
ip_nat_rtsp v0.01 loading
Security configuration management initiated successfully!
Read Flash: part=[FACTORYINFO]
Enter kerSysFactoryInfoGet: strLen[64],offset[0]
FactoryInfo[1-10]=[LK93211363]
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
device wl0 entered promiscuous mode
br0: port 2(wl0) entering learning state
br0: topology change detected, propagating
br0: port 2(wl0) entering forwarding state
device wl0.1 entered promiscuous mode
br0: port 3(wl0.1) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0.1) entering forwarding state
hlist_add_head_rcu=[2:26:91:20:84:17]-----------------
source->dev->name=[wl0] ,is_local=[0]
device eth0 left promiscuous mode
br0: port 1(eth0) entering disabled state
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
device wl0 left promiscuous mode
br0: port 2(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 2(wl0) entering learning state
br0: topology change detected, propagating
br0: port 2(wl0) entering forwarding state
hlist_add_head_rcu=[2:26:91:20:84:17]-----------------
source->dev->name=[wl0] ,is_local=[0]
device wl0.1 left promiscuous mode
br0: port 3(wl0.1) entering disabled state
device wl0.1 entered promiscuous mode
br0: port 3(wl0.1) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0.1) entering forwarding state
hlist_add_head_rcu=[0:12:17:41:db:fb]-----------------
source->dev->name=[wl0] ,is_local=[0]
Read Flash: part=[SCRATCH_PAD]
Read Flash: part=[SCRATCH_PAD]
Network initiated successfully!
Web Server initiated successfully!
Read Flash: part=[SCRATCH_PAD]
Read Flash: part=[SYSTEM_INI]
Enter kerSysSystemIniGet: strLen[4096],offset[0],fInfo.flash_system_ini_blk_offset=[0]
SystemIni[1-10]=[[quickSetu]
br0: port 1(eth0) entering disabled state
Cfm initiated successfully!
Read Flash: part=[FACTORYINFO]
Enter kerSysFactoryInfoGet: strLen[1024],offset[0]
FactoryInfo[1-10]=[LK93211363]
Read Flash: part=[PERSISTENT]
Read Flash: part=[BACKUP]
Enter kerSysBackupGet: strLen[24576],offset[0],fInfo.flash_backup_blk_offset=[0]
Backup[1-10]=[<psitree>
]
Enter kerSysScratchPadBlock
read buffer len is: 4096
Read Flash: part=[SYSTEM_INI]
Enter kerSysSystemIniGet: strLen[4096],offset[0],fInfo.flash_system_ini_blk_offset=[0]
SystemIni[1-10]=[[quickSetu]
SystemIni[1-10]=[[quickSetu](Last edited by naplam on 18 Jan 2010, 21:19)
Hi,DeerHunter
this photo is not show,
http://img12.imageshack.us/img12/3689/patata.jpg
http://img12.imageshack.us/img12/patata.jpg/1/w2048.png
Can you send me? my email: 83158275@qq.com,Thank you
Info entered to wiki
http://wiki.openwrt.org/toh/sagem/fast2404
Please add/fix more information about the router.
Does it work with Sagem fast 2604?
fernandoch wrote:
Does it work with Sagem fast 2604?
Check http://wiki.openwrt.org/toh/sagem/fast2604 seems like is possible.
The discussion might have continued from here.
Page 1 of 1