Hello,
I am working on compiling an image for a Routerboard 411 using trunk. I have followed the howto for the 433 @ http://blog.vodkamelone.de/archives/148 … RB433.html.
I am able to boot from tftp and then copy the kernal and FS over with no issues. After I copy everything into NAND and I reboot from local, I am unable to configure anything.
Here's the boot output:
RouterBOOT booter 2.20
RouterBoard 411
CPU frequency: 300 MHz
Memory size: 32 MB
Press any key within 2 seconds to enter setup..
loading kernel from nand... OK
setting up elf image... OK
jumping to kernel code
Linux version 2.6.30.9 (swolfe@utility.cs1.cybera.net) (gcc version 4.3.3 (GCC) ) #11 Wed Nov 11 13:33:44 CST 2009
console [early0] enabled
CPU revision is: 00019374 (MIPS 24Kc)
Atheros AR7130 rev 2, CPU:300.000 MHz, AHB:150.000 MHz, DDR:300.000 MHz
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: rootfstype=squashfs,yaffs,jffs2 noinitrd console=ttyS0,115200 console=ttyS0,115200 gpio=4031 HZ=150000000 mem=32M kmac=00:0C:42:4C:B4:24 board=411 boot=1 mlc=1
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00070080
Readback ErrCtl register=00070080
NR_IRQS:56
PID hash table entries: 128 (order: 7, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29516k/32768k available (1932k kernel code, 3252k reserved, 422k data, 136k init, 0k highmem)
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 199.88 BogoMIPS (lpj=999424)
Mount-cache hash table entries: 512
net_namespace: 528 bytes
NET: Registered protocol family 16
MIPS: machine is MikroTik RouterBOARD 411/A/AH
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
pci 0000:00:00.0: PME# disabled
PCI: mapping irq 48 to pin1@0000:00:12.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
yaffs Nov 10 2009 18:02:58 Installing.
msgmni has been set to 57
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
console handover: boot [early0] -> real [ttyS0]
ag71xx_mdio: probed
eth0: Atheros AG71xx at 0xb9000000, irq 4
NAND flash driver for RouterBoard 4xx series version 0.1.10
NAND SPI clock 25000 kHz (AHB 150000 kHz / 6)
FLASH SPI clock 25000 kHz (AHB 150000 kHz / 6)
NAND device: Manufacturer ID: 0x20, Chip ID: 0x76 (ST Micro NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x000000000000-0x000000040000 : "booter"
0x000000040000-0x000000400000 : "kernel"
0x000000400000-0x000004000000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
split_squashfs: error occured while reading from "NAND 64MiB 3,3V 8-bit"
Atheros AR71xx SPI Controller driver version 0.2.4
Atheros AR71xx hardware watchdog driver version 0.1.0
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 136k freed
Please be patient, while OpenWrt loads ...
- preinit -
Registered led device: rb4xx:yellow:user
Press CTRL-C for failsafe
gpio-buttons driver version 0.1.1
input: gpio-buttons as /devices/platform/gpio-buttons/input/input0
Button Hotplug driver version 0.3.1
- init -
Please press Enter to activate this console. cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
PCI: Enabling device 0000:00:12.0 (0000 -> 0002)
ath5k 0000:00:12.0: registered as 'phy0'
ath5k phy0: Atheros AR5414 chip found (MAC: 0xa5, PHY: 0x61)
cfg80211: Calling CRDA for country: US
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (512 buckets, 2048 max)
ath_hal: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
ath_hal: 2009-05-08 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, RF2425, REGOPS_FUNC, XR)
ath_pci: trunk
wlan: trunk
wlan: mac acl policy registered
ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (trunk)
ath_rate_minstrel: look around rate set to 10%
ath_rate_minstrel: EWMA rolloff level set to 75%
ath_rate_minstrel: max segment size in the mrr set to 6000 us
BusyBox v1.14.4 (2009-11-10 17:52:07 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
KAMIKAZE (bleeding edge, r18359) ------------------
* 10 oz Vodka Shake well with ice and strain
* 10 oz Triple sec mixture into 10 shot glasses.
* 10 oz lime juice Salute!
---------------------------------------------------
root@OpenWrt:/#The problem I run into is when I try to change the password or do an opkg update:
root@OpenWrt:/# passwd
Changing password for root
New password:
Retype password:
passwd: /etc/passwd: Read-only file system
passwd: cannot update password file /etc/passwd
root@OpenWrt:/# opkg update
Collected errors:
* Could not obtain administrative lock
root@OpenWrt:/# df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 1.5M 1.5M 0 100% /
tmpfs 14.5M 32.0K 14.4M 0% /tmp
tmpfs 512.0K 0 512.0K 0% /dev
root@OpenWrt:/#I'm not sure if I'm missing something here or not. BTW, I've tried modifying "CONFIG_HAVE_MLOCK=n" in the config-2.6.30 file.
Any thoughts? I'm at a loss.