I have a small AP, Creative VF0180
CPU:Broadcom4712 Memory:64M Only one lan inferface
I can get output via TTL, but cant ping the AP. And the /etc/config/wireless is empty!!!
The kernel is 2.6:
root@OpenWrt:/# uname -a
Linux OpenWrt 2.6.25.20 #3 Mon Sep 14 09:03:26 UTC 2009 mips unknown
This output is from TTL:
root@OpenWrt:/# ifconfig
br-lan Link encap:Ethernet HWaddr 00:01:E3:0E:95:C4
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:402 (402.0 B)
eth0 Link encap:Ethernet HWaddr 00:01:E3:0E:95:C4
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:5
eth0.0 Link encap:Ethernet HWaddr 00:01:E3:0E:95:C4
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
eth0.1 Link encap:Ethernet HWaddr 00:01:E3:0E:95:C4
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
And the /etc/config/network:
root@OpenWrt:/# more /etc/config/network
#### VLAN configuration
config switch eth0
option vlan0 "1 2 3 4 5*"
option vlan1 "0 5"
#### Loopback configuration
config interface loopback
option ifname "lo"
option proto static
option ipaddr 127.0.0.1
option netmask 255.0.0.0
#### LAN configuration
config interface lan
option type bridge
option ifname "eth0.0"
option proto static
option ipaddr 192.168.1.1
option netmask 255.255.255.0
#### WAN configuration
config interface wan
option ifname "eth0.1"
option proto dhcp
Under the /lib/wifi/ have a file callled hostapd.sh, but /etc/config/wireless is also empty.
root@OpenWrt:/# /lib/wifi/hostapd.sh
dmesg information:
root@OpenWrt:/# dmesg
Linux version 2.6.25.20 (andy@stable-sandbox) (gcc version 4.1.2) #3
Mon Sep 14 09:03:26 UTC 2009
CPU revision is: 00029007 (Broadcom BCM3302)
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x09, vendor 0x4243)
ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x07, vendor 0x4243)
ssb: Core 2 found: Fast Ethernet (cc 0x806, rev 0x07, vendor 0x4243)
ssb: Core 3 found: USB 1.1 Device (cc 0x818, rev 0x01, vendor 0x4243)
ssb: Core 4 found: USB 1.1 Host (cc 0x817, rev 0x01, vendor 0x4243)
ssb: Core 5 found: MIPS 3302 (cc 0x816, rev 0x01, vendor 0x4243)
ssb: Core 6 found: MEMC SDRAM (cc 0x80F, rev 0x01, vendor 0x4243)
ssb: Core 7 found: PCI (cc 0x804, rev 0x0A, vendor 0x4243)
ssb: Initializing MIPS core...
ssb: set_irq: core 0x0812, irq 2 => 2
ssb: set_irq: core 0x0806, irq 3 => 3
ssb: set_irq: core 0x0817, irq 0 => 4
ssb: Sonics Silicon Backplane found at address 0x18000000
Serial init done.
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Entering add_active_range(0, 0, 4096) 0 entries of 256 used
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0 -> 4096
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 4096
On node 0 totalpages: 4096
Normal zone: 32 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 4064 pages, LIFO batch:0
Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2
init=/etc/preinit noinitrd console=ttyS0,115200
Primary instruction cache 8kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 4kB, 2-way, VIPT, no aliases, linesize 16 bytes
Synthesized clear page handler (26 instructions).
Synthesized copy page handler (46 instructions).
PID hash table entries: 64 (order: 6, 256 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 13580k/16384k available (2073k kernel code, 2804k reserved,
308k data, 128k init, 0k highmem)
Calibrating delay loop... 198.65 BogoMIPS (lpj=397312)
Mount-cache hash table entries: 512
net_namespace: 540 bytes
NET: Registered protocol family 16
Switched to high resolution mode on CPU 0
ssb: PCIcore in host mode found
Registering a PCI bus after boot
PCI: Fixing up bridge 0000:00:00.0
PCI: Setting latency timer of device 0000:00:00.0 to 64
PCI: Fixing up device 0000:00:00.0
PCI: Fixing latency timer of device 0000:00:00.0 to 168
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
detected lzma initramfs
initramfs: LZMA lc=1,lp=2,pb=2,origSize=512
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:01:e3:0e:95:c4
flash init: 0x1c000000 0x02000000
Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Physically mapped flash: Found an alias at 0x400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0xc00000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1c00000 for the chip at 0x0
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x400000 at 0x1fc00000
bootloader size: 262144
Creating 4 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x003f0000 : "linux"
0x000fd400-0x003f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary --
force read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=250000, len=1A0000
0x00250000-0x003f0000 : "rootfs_data"
0x003f0000-0x00400000 : "nvram"
TCP vegas registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 128k freed
Please be patient, while OpenWrt loads ...
Algorithmics/MIPS FPU Emulator v1.5
diag: Detected 'Siemens SE505 V2'
roboswitch: Probing device eth0: Invalid phy address (0)
roboswitch: Probing device eth1: No such device
roboswitch: Probing device eth2: No such device
roboswitch: Probing device eth3: No such device
b44: eth0: Link is up at 10 Mbps, half duplex.
b44: eth0: Flow control is off for TX and off for RX.
b44: eth0: powering down PHY
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
There is already a switch registered on the device 'eth0'
roboswitch: Probing device eth1: No such device
roboswitch: Probing device eth2: No such device
roboswitch: Probing device eth3: No such device
b44: eth0: Link is up at 10 Mbps, half duplex.
b44: eth0: Flow control is off for TX and off for RX.
PPP generic driver version 2.4.2
br-lan: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device eth0.0 entered promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0.0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 1(eth0.0) entering forwarding state
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
b44: eth0: Link is down.
br-lan: port 1(eth0.0) entering disabled state
b44: eth0: Link is up at 10 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
br-lan: port 1(eth0.0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 1(eth0.0) entering forwarding state
Please help me, thx.