OpenWrt Forum Archive

Topic: comgt configration

The content of this topic has been archived on 14 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

Post #1
stockjp
16 Nov 2009, 10:51

I can not connect 3g
pleas help me.
What is the problem?

[vi /dev/config/network]

config 'interface' 'ppp'
        option 'ifname' 'ppp0'
        option 'proto' '3g'
        option 'username' 'em'
        option 'password' '123456789'
        option 'device' '/dev/ttyUSB2'
        option 'pincode' '9999'
        option 'service' 'umts'
        option 'apn' 'emb.ne.jp'

[ls /dev/tty*]
/dev/tty      /dev/ttyUSB0  /dev/ttyUSB2  /dev/ttyUSB4
/dev/ttyS0    /dev/ttyUSB1  /dev/ttyUSB3


[ifup ppp]
SIM ready
PIN set successfully

{syslog}
ay 31 19:42:59 fon daemon.notice pppd[1634]: pppd 2.4.3 started by root, uid 0
May 31 19:43:00 fon local2.info chat[1641]: abort on (BUSY)
May 31 19:43:00 fon local2.info chat[1641]: abort on (NO CARRIER)
May 31 19:43:00 fon local2.info chat[1641]: abort on (ERROR)
May 31 19:43:00 fon local2.info chat[1641]: report (CONNECT)
May 31 19:43:00 fon local2.info chat[1641]: timeout set to 10 seconds
May 31 19:43:00 fon local2.info chat[1641]: send (AT&F^M)
May 31 19:43:00 fon local2.info chat[1641]: expect (OK)
May 31 19:43:00 fon local2.info chat[1641]: AT&F^M^M
May 31 19:43:00 fon local2.info chat[1641]: OK
May 31 19:43:00 fon local2.info chat[1641]:  -- got it
May 31 19:43:00 fon local2.info chat[1641]: send (ATE1^M)
May 31 19:43:00 fon local2.info chat[1641]: expect (OK)
May 31 19:43:00 fon local2.info chat[1641]: ^M
May 31 19:43:00 fon local2.info chat[1641]: ATE1^M^M
May 31 19:43:00 fon local2.info chat[1641]: OK
May 31 19:43:00 fon local2.info chat[1641]:  -- got it
May 31 19:43:00 fon local2.info chat[1641]: send (AT+CGDCONT=1,"IP","emb.ne.jp"^M)
May 31 19:43:00 fon local2.info chat[1641]: timeout set to 30 seconds
May 31 19:43:00 fon local2.info chat[1641]: expect (OK)
May 31 19:43:00 fon local2.info chat[1641]: ^M
May 31 19:43:00 fon local2.info chat[1641]: AT+CGDCONT=1,"IP","emb.ne.jp"^M^M
May 31 19:43:00 fon local2.info chat[1641]: OK
May 31 19:43:00 fon local2.info chat[1641]:  -- got it
May 31 19:43:00 fon local2.info chat[1641]: send (ATD*99***1#^M)
May 31 19:43:00 fon local2.info chat[1641]: expect (CONNECT)
May 31 19:43:00 fon local2.info chat[1641]: ^M
May 31 19:43:00 fon local2.info chat[1641]: ATD*99***1#^M^M
May 31 19:43:00 fon local2.info chat[1641]: CONNECT
May 31 19:43:00 fon local2.info chat[1641]:  -- got it
May 31 19:43:00 fon local2.info chat[1641]: send ( ^M)
May 31 19:43:01 fon daemon.info pppd[1634]: Serial connection established.
May 31 19:43:01 fon daemon.info pppd[1634]: Using interface ppp0
May 31 19:43:01 fon daemon.notice pppd[1634]: Connect: ppp0 <--> /dev/ttyUSB2
May 31 19:43:32 fon daemon.warn pppd[1634]: LCP: timeout sending Config-Requests
May 31 19:43:32 fon daemon.notice pppd[1634]: Connection terminated.
May 31 19:43:32 fon daemon.warn pppd[1634]: Receive serial link is not 8-bit clean:
May 31 19:43:32 fon daemon.warn pppd[1634]: Problem: all had bit 7 set to 0
May 31 19:43:32 fon daemon.notice pppd[1634]: Modem hangup

(Last edited by stockjp on 16 Nov 2009, 19:34)

Post #2
Dogge
16 Nov 2009, 20:22

Maybe you have to use usb_modeswitch

Post #3
stockjp
16 Nov 2009, 20:37

thank you

I used usb_modeswitch.

(Last edited by stockjp on 16 Nov 2009, 20:38)

Post #4
aport
17 Nov 2009, 01:02
Dogge wrote:

Maybe you have to use usb_modeswitch

If the /dev/ttyUSBX devices exist, then he doesn't have to modeswitch anything...



Are you sure that /dev/ttyUSB2 is the correct port to use? Which modem are you using?

Post #5
stockjp
17 Nov 2009, 15:54

I try to use the device "D31HW".

It is japames device.

this device must use "usb_modeswitch"

I input comand "usb_modeswitch",then i use ttyUSB*.

Post #6
staylo
18 Nov 2009, 12:07

For some reason one of my K3565 dongles (maybe a later version than the other) only works with

option 'device' '/dev/usb/tts/2'

not

option 'device' '/dev/ttyUSB2'

I have no idea why, but maybe try that?

Post #7
stockjp
18 Nov 2009, 15:38

thank you aport and staylo

I read  japanese website.
This deice run "ttyUSB2". but on ubunte os


[# ls -ls /dev/]
   0 crw-r--r--    1 root     root       5,   1 Jan  1  1970 console
   0 crw-r--r--    1 root     root      10,  63 Jan  1  1970 cpu_dma_latency
   0 crw-rw-rw-    1 root     root       1,   7 Jan  1  1970 full
   0 crw-rw-rw-    1 root     root     254,   0 Jan  1  1970 gpio
   0 crw-r--r--    1 root     root       1,  11 Jan  1  1970 kmsg
   0 srw-rw-rw-    1 root     root            0 May 31 19:36 log
   0 crw-r--r--    1 root     root       1,   1 Jan  1  1970 mem
   0 crw-r--r--    1 root     root      90,   0 Jan  1  1970 mtd0
   0 crw-r--r--    1 root     root      90,   1 Jan  1  1970 mtd0ro
   0 crw-r--r--    1 root     root      90,   2 Jan  1  1970 mtd1
   0 crw-r--r--    1 root     root      90,   3 Jan  1  1970 mtd1ro
   0 crw-r--r--    1 root     root      90,   4 Jan  1  1970 mtd2
   0 crw-r--r--    1 root     root      90,   5 Jan  1  1970 mtd2ro
   0 crw-r--r--    1 root     root      90,   6 Jan  1  1970 mtd3
   0 crw-r--r--    1 root     root      90,   7 Jan  1  1970 mtd3ro
   0 crw-r--r--    1 root     root      90,   8 Jan  1  1970 mtd4
   0 crw-r--r--    1 root     root      90,   9 Jan  1  1970 mtd4ro
   0 crw-r--r--    1 root     root      90,  10 Jan  1  1970 mtd5
   0 crw-r--r--    1 root     root      90,  11 Jan  1  1970 mtd5ro
   0 crw-r--r--    1 root     root      90,  12 Jan  1  1970 mtd6
   0 crw-r--r--    1 root     root      90,  13 Jan  1  1970 mtd6ro
   0 brw-r--r--    1 root     root      31,   0 Jan  1  1970 mtdblock0
   0 brw-r--r--    1 root     root      31,   1 Jan  1  1970 mtdblock1
   0 brw-r--r--    1 root     root      31,   2 Jan  1  1970 mtdblock2
   0 brw-r--r--    1 root     root      31,   3 Jan  1  1970 mtdblock3
   0 brw-r--r--    1 root     root      31,   4 Jan  1  1970 mtdblock4
   0 brw-r--r--    1 root     root      31,   5 Jan  1  1970 mtdblock5
   0 brw-r--r--    1 root     root      31,   6 Jan  1  1970 mtdblock6
   0 crw-r--r--    1 root     root      10,  62 Jan  1  1970 network_latency
   0 crw-r--r--    1 root     root      10,  61 Jan  1  1970 network_throughput
   0 crw-rw-rw-    1 root     root       1,   3 Jan  1  1970 null
   0 crw-r--r--    1 root     root       1,   4 Jan  1  1970 port
   0 crw-------    1 root     root     108,   0 May 31 19:36 ppp
   0 crw-rw-rw-    1 root     root       5,   2 Jan  1  1970 ptmx
   0 drwxr-xr-x    2 root     root            0 Jan  1  1970 pts
   0 crw-r--r--    1 root     root       1,   8 Jan  1  1970 random
   0 drwxr-xr-x    2 root     root           40 Jan  1  1970 shm
   0 crw-rw-rw-    1 root     root       5,   0 Jan  1  1970 tty
   0 crw-rw-rw-    1 root     root       4,  64 May 31 19:38 ttyS0
   0 crw-r--r--    1 root     root       1,   9 Jan  1  1970 urandom
   0 crw-r--r--    1 root     root     189,   0 May 31 19:36 usb1
   0 crw-r--r--    1 root     root     253,   1 May 31 19:36 usbdev1.1_ep00
   0 crw-r--r--    1 root     root     253,   0 May 31 19:36 usbdev1.1_ep81
   0 crw-r--r--    1 root     root      10, 130 Jan  1  1970 watchdog
   0 crw-rw-rw-    1 root     root       1,   5 Jan  1  1970 zero


[ I set usb device on board]

usb 1-1: new high speed USB device using ehci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
scsi 0:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2


[# usb_modeswitch]

* usb_modeswitch: tool for controlling "flip flop" mode USB devusb 1-1: USB disconnect, address 2
ices
* Version 0.9.5 (C) Josua Dietze 2008
* Works with libusb 0.1.12 and probably other versions

Looking for target devices
No target device found
Looking for default devices
Found default devices (1)
Prepare switching, accessing latest device
Looking for active default driver to detach it
OK, driver found ("usb-storage")
OK, Driver "usb-storage" successfully detached
Setting up communication with device
Trying to send the message
OK, message successfully sent.
-> See /proc/bus/usb/devices (or call lsusb) for changes. Bye


usb 1-1: new high speed USB device using ehci_hcd and address 3
usb 1-1: configuration #1 chosen from 1 choice
usbserial_generic 1-1:1.0: generic converter detected
usb 1-1: generic converter now attached to ttyUSB0
usbserial_generic 1-1:1.1: generic converter detected
usb 1-1: generic converter now attached to ttyUSB1
usbserial_generic 1-1:1.2: generic converter detected
usb 1-1: generic converter now attached to ttyUSB2
usbserial_generic 1-1:1.3: generic converter detected
usb 1-1: generic converter now attached to ttyUSB3
usbserial_generic 1-1:1.4: generic converter detected
usb 1-1: generic converter now attached to ttyUSB4



[# ls -ls /dev/]
   0 crw-r--r--    1 root     root     189,   1 May 31 19:39 1-1
   0 crw-r--r--    1 root     root       5,   1 Jan  1  1970 console
   0 crw-r--r--    1 root     root      10,  63 Jan  1  1970 cpu_dma_latency
   0 crw-rw-rw-    1 root     root       1,   7 Jan  1  1970 full
   0 crw-rw-rw-    1 root     root     254,   0 Jan  1  1970 gpio
   0 crw-r--r--    1 root     root       1,  11 Jan  1  1970 kmsg
   0 srw-rw-rw-    1 root     root            0 May 31 19:36 log
   0 crw-r--r--    1 root     root       1,   1 Jan  1  1970 mem
   0 crw-r--r--    1 root     root      90,   0 Jan  1  1970 mtd0
   0 crw-r--r--    1 root     root      90,   1 Jan  1  1970 mtd0ro
   0 crw-r--r--    1 root     root      90,   2 Jan  1  1970 mtd1
   0 crw-r--r--    1 root     root      90,   3 Jan  1  1970 mtd1ro
   0 crw-r--r--    1 root     root      90,   4 Jan  1  1970 mtd2
   0 crw-r--r--    1 root     root      90,   5 Jan  1  1970 mtd2ro
   0 crw-r--r--    1 root     root      90,   6 Jan  1  1970 mtd3
   0 crw-r--r--    1 root     root      90,   7 Jan  1  1970 mtd3ro
   0 crw-r--r--    1 root     root      90,   8 Jan  1  1970 mtd4
   0 crw-r--r--    1 root     root      90,   9 Jan  1  1970 mtd4ro
   0 crw-r--r--    1 root     root      90,  10 Jan  1  1970 mtd5
   0 crw-r--r--    1 root     root      90,  11 Jan  1  1970 mtd5ro
   0 crw-r--r--    1 root     root      90,  12 Jan  1  1970 mtd6
   0 crw-r--r--    1 root     root      90,  13 Jan  1  1970 mtd6ro
   0 brw-r--r--    1 root     root      31,   0 Jan  1  1970 mtdblock0
   0 brw-r--r--    1 root     root      31,   1 Jan  1  1970 mtdblock1
   0 brw-r--r--    1 root     root      31,   2 Jan  1  1970 mtdblock2
   0 brw-r--r--    1 root     root      31,   3 Jan  1  1970 mtdblock3
   0 brw-r--r--    1 root     root      31,   4 Jan  1  1970 mtdblock4
   0 brw-r--r--    1 root     root      31,   5 Jan  1  1970 mtdblock5
   0 brw-r--r--    1 root     root      31,   6 Jan  1  1970 mtdblock6
   0 crw-r--r--    1 root     root      10,  62 Jan  1  1970 network_latency
   0 crw-r--r--    1 root     root      10,  61 Jan  1  1970 network_throughput
   0 crw-rw-rw-    1 root     root       1,   3 Jan  1  1970 null
   0 crw-r--r--    1 root     root       1,   4 Jan  1  1970 port
   0 crw-------    1 root     root     108,   0 May 31 19:36 ppp
   0 crw-rw-rw-    1 root     root       5,   2 Jan  1  1970 ptmx
   0 drwxr-xr-x    2 root     root            0 Jan  1  1970 pts
   0 crw-r--r--    1 root     root       1,   8 Jan  1  1970 random
   0 drwxr-xr-x    2 root     root           40 Jan  1  1970 shm
   0 crw-rw-rw-    1 root     root       5,   0 Jan  1  1970 tty
   0 crw-rw-rw-    1 root     root       4,  64 May 31 19:40 ttyS0
   0 crw-rw-rw-    1 root     root     188,   0 May 31 19:40 ttyUSB0
   0 crw-rw-rw-    1 root     root     188,   1 May 31 19:40 ttyUSB1
   0 crw-rw-rw-    1 root     root     188,   2 May 31 19:40 ttyUSB2
   0 crw-rw-rw-    1 root     root     188,   3 May 31 19:40 ttyUSB3
   0 crw-rw-rw-    1 root     root     188,   4 May 31 19:40 ttyUSB4
   0 crw-r--r--    1 root     root       1,   9 Jan  1  1970 urandom
   0 crw-r--r--    1 root     root     189,   0 May 31 19:36 usb1
   0 crw-r--r--    1 root     root     253,   1 May 31 19:36 usbdev1.1_ep00
   0 crw-r--r--    1 root     root     253,   0 May 31 19:36 usbdev1.1_ep81
   0 crw-r--r--    1 root     root     253,   4 May 31 19:39 usbdev1.2_ep00
   0 crw-r--r--    1 root     root     253,   3 May 31 19:39 usbdev1.2_ep01
   0 crw-r--r--    1 root     root     253,   2 May 31 19:39 usbdev1.2_ep81
   0 crw-r--r--    1 root     root     253,  14 May 31 19:40 usbdev1.3_ep00
   0 crw-r--r--    1 root     root     253,   4 May 31 19:40 usbdev1.3_ep01
   0 crw-r--r--    1 root     root     253,   7 May 31 19:40 usbdev1.3_ep02
   0 crw-r--r--    1 root     root     253,   9 May 31 19:40 usbdev1.3_ep03
   0 crw-r--r--    1 root     root     253,  11 May 31 19:40 usbdev1.3_ep04
   0 crw-r--r--    1 root     root     253,  12 May 31 19:40 usbdev1.3_ep05
   0 crw-r--r--    1 root     root     253,   2 May 31 19:40 usbdev1.3_ep81
   0 crw-r--r--    1 root     root     253,   3 May 31 19:40 usbdev1.3_ep82
   0 crw-r--r--    1 root     root     253,   5 May 31 19:40 usbdev1.3_ep83
   0 crw-r--r--    1 root     root     253,   6 May 31 19:40 usbdev1.3_ep84
   0 crw-r--r--    1 root     root     253,   8 May 31 19:40 usbdev1.3_ep85
   0 crw-r--r--    1 root     root     253,  10 May 31 19:40 usbdev1.3_ep86
   0 crw-r--r--    1 root     root     253,  13 May 31 19:40 usbdev1.3_ep87
   0 crw-r--r--    1 root     root      10, 130 Jan  1  1970 watchdog
   0 crw-rw-rw-    1 root     root       1,   5 Jan  1  1970 zero

Post #8
stockjp
18 Nov 2009, 15:58

I try "ttyUSB0"

I successed

Post #9
aport
19 Nov 2009, 19:19
stockjp wrote:

I try "ttyUSB0"

I successed

Happy it works!

Post #10
pepenue
13 Mar 2010, 00:54

I can not connect 3g
pleas help me.
What is the problem?

[/config/network]

config 'interface' 'ppp'
        option 'ifname' 'ppp'
        option 'proto' '3g'
        option 'device' '/dev/ttyUSB1'
        option 'username' 'MOVISTAR'
        option 'password' 'MOVISTAR'
        option 'apn' 'movistar.es'

[ifup ppp]

SIM ready
PIN set successfully

[logread]

Jan  1 00:16:05 OpenWrt local2.info chat[1545]: abort on (BUSY)
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: abort on (NO CARRIER)
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: abort on (ERROR)
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: report (CONNECT)
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: timeout set to 10 seconds
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: send (AT&F^M)
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: expect (OK)
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: AT&F^M^M
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: OK
Jan  1 00:16:05 OpenWrt local2.info chat[1545]:  -- got it
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: send (ATE1^M)
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: expect (OK)
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: ^M
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: ATE1^M^M
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: OK
Jan  1 00:16:05 OpenWrt local2.info chat[1545]:  -- got it
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: send (AT+CGDCONT=1,"IP","movistar.es"^M)
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: timeout set to 30 seconds
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: expect (OK)
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: ^M
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: AT+CGDCONT=1,"IP","movistar.es"^M^M
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: OK
Jan  1 00:16:05 OpenWrt local2.info chat[1545]:  -- got it
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: send (ATD*99***1#^M)
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: expect (CONNECT)
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: ^M
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: ATD*99***1#^M^M
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: NO CARRIER
Jan  1 00:16:05 OpenWrt local2.info chat[1545]:  -- failed
Jan  1 00:16:05 OpenWrt local2.info chat[1545]: Failed (NO CARRIER)
Jan  1 00:16:05 OpenWrt daemon.err pppd[1474]: Connect script failed

Post #11
delix
13 Jun 2010, 15:49

2 pepenue
I had the same shit. The problrem was in following line
option ‘device’ ‘/dev/ttyUSB1?
Just try ttyUSB0
‘device’ ‘/dev/ttyUSB0?
It works for me.
I used D-Link DIR 320 with Huawei E219 3g modem.
Btw the pincode was desibled.

P.S. I've answerred you on some another site smile

The discussion might have continued from here.