The content of this topic has been archived on 30 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.
Hi,
I have WLA 5000AP.
I bought it because I want to use for home automation (it has seria port connectorl).
In documentation there is that I can install OPENWRT.
http://openwrt.dlabac.net/Archiv/openwr … ge.www.bin
But this file does not exist. I am not able to find out which version of OPENWRT I should use.
Please can you help me?
I would like just to download an image to the router, not to compile it.
Thank you for any help.
Regards,
Jirii
I have dowloaded http://download.openwrt.net/atheros/bin … s2-64k.bin
I was able to flash this via web interface.
Now I can ssh to router, but there is no web interface nor nvram command.
I am new in openwrt, so I do not know how to fix this and/or how to add WebIF.
can you please help me?
attached dmesg
BusyBox v1.11.2 (2009-08-24 12:59:50 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
KAMIKAZE (8.09.1, r17282) ----------------------------
* 10 oz Vodka Shake well with ice and strain
* 10 oz Triple sec mixture into 10 shot glasses.
* 10 oz lime juice Salute!
---------------------------------------------------
root@OpenWrt:/# dmesg
Linux version 2.6.26.8 (valxdater@vx) (gcc version 4.1.2) #2 Mon Aug 24 14:03:02 CEST 2009
CPU revision is: 00018009 (MIPS 4Kc)
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Entering add_active_range(0, 0, 8192) 0 entries of 256 used
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0 -> 8192
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 8192
On node 0 totalpages: 8192
Normal zone: 64 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 8128 pages, LIFO batch:0
Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 init=/etc/pr einit
Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 16 bytes
PID hash table entries: 128 (order: 7, 512 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29664k/32768k available (1900k kernel code, 3104k reserved, 430k data, 1 24k init, 0k highmem)
SLUB: Genslabs=6, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 179.81 BogoMIPS (lpj=899072)
Mount-cache hash table entries: 512
net_namespace: 644 bytes
NET: Registered protocol family 16
CA8 device "Ovislink WLA-5000AP" found!
Recovering MAC address 00:4F:69:50:1B:9B!
Radio config found at offset -0x4000 (0x100)
Switched to high resolution mode on CPU 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
ar531x: Registering GPIODEV device
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) Š 2001-2006 Red Hat, Inc.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0xbc000003 (irq = 37) is a 16550A
eth0: Atheros AR231x: 00:4f:69:50:1b:9c, irq 4
ar2313_eth_mii: probed
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01)
physmap platform flash device: 00800000 at 1e000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank
physmap-flash.0: Found an alias at 0x400000 for the chip at 0x0
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
Searching for RedBoot partition table in physmap-flash.0 at offset 0x3d0000
Searching for RedBoot partition table in physmap-flash.0 at offset 0x3e0000
Searching for RedBoot partition table in physmap-flash.0 at offset 0x3f0000
No RedBoot partition table detected in physmap-flash.0
physmap-flash.0: Searching for CA8 partitions...
physmap-flash.0: CA8 device found: Ovislink WLA-5000AP!
physmap-flash.0: CA8 kernel length = 0xc29aa, crc = 0x60ab2b5
7 ca8parts partitions found on MTD device physmap-flash.0
Creating 7 MTD partitions on "physmap-flash.0":
0x00000000-0x00002000 : "boardconfig"
0x00002000-0x00050000 : "loader"
0x00050000-0x00120000 : "kernel"
0x00120000-0x003f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
split_squashfs: no squashfs found in "physmap-flash.0"
0x003f0000-0x00400000 : "boarddata"
0x00050000-0x003f0000 : "firmware"
0x00000000-0x00400000 : "wholeflash"
TCP vegas registered
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (jffs2 filesystem) readonly.
Freeing unused kernel memory: 124k freed
Please be patient, while OpenWrt loads ...
eth0: Configuring MAC for full duplex
Algorithmics/MIPS FPU Emulator v1.5
device eth0 entered promiscuous mode
br-lan: port 1(eth0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 1(eth0) entering forwarding state
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
wlan: trunk
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 2009-05-08 (AR5212, AR5312, RF5111, RF5112, RF2316, RF2317, REGOPS_FUNC , TX_DESC_SWAP, XR)
ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (trunk)
ath_rate_minstrel: look around rate set to 10%
ath_rate_minstrel: EWMA rolloff level set to 75%
ath_rate_minstrel: max segment size in the mrr set to 6000 us
wlan: mac acl policy registered
ath_ahb: trunk
Atheros HAL provided by OpenWrt, DD-WRT and MakSat Technologies
wifi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36 Mbps 48Mbps 54Mbps
wifi0: turboA rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
ath_ahb: wifi0: Atheros 5312 WiSoC: mem=0xb8500000, irq=5
root@OpenWrt:/#
root@OpenWrt:/#
(Last edited by js2002 on 6 Jan 2011, 06:25)
Hey js2002. Could you provide more info about porting OpenWRT on your device? What is your progress?
The discussion might have continued from here.