OpenWrt Forum Archive

Topic: OpenWrt on Fast FW300R Version 9.1 Photos Attached

The content of this topic has been archived on 28 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

Hello Friends,


Is it possible to use openwrt on the Fast Fw300R version 9.1?

I´ve take these photos about the chipsets:

CPU: QCA9533-AL3A
64Mb DDR SDRAM ZENTEL: A3S64D40GTP

It is very similar to MW316R, board is much the same.


Also, If someone could help me finding the serial port, i could try to create an image for it (are there any guidelines?)

Thanks,

Pucci


PunBB bbcode test
PunBB bbcode test

(Last edited by leopucci on 9 Nov 2013, 22:42)

Looks like J3 is standart UART interface. From top: power, ground  and (RX and TX or TX and RX)

Well,  that´s it!

After some soldering... here is the output!

U-boot loading VXWORKS... with some TP-LINK logos..


Can anyone suggest an image to run on this?

I think the next step is to point u boot to load another image via tftp, right?

Thanks in advance,

Pucci




U-Boot 1.1.4 (Build from LSDK- at Mar 21 2013 - 10:06:47)

ap143 - Honey Bee 1.1

DRAM:   8 MB
Top of RAM usable for U-Boot at: 80800000
Reserving 128k for U-Boot at: 807dc000
Reserving 132k for malloc() at: 807bb000
Reserving 44 Bytes for Board Info at: 807bafd4
Reserving 36 Bytes for Global Data at: 807bafb0
Reserving 128k for boot params() at: 8079afb0
Stack Pointer at: 8079af98
Now running in RAM - U-Boot at: 807dc000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x14
flash size 4MB, sector count = 256
Flash:  1 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ---->S27 PHY*
S27 reg init
: cfg1 0x800c0000 cfg2 0x7114
eth0: 28:--:--:--:--: tongue
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
Honey Bee ---->  MAC 1 S27 PHY *
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: 28:2c:b2:df:d7:cf
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x4b97a100
Hit any key to stop autoboot:  0
vxWorks.bin from =0x48e90, len=0x864a7
Uncompressing...done
                                    Attaching interface lo0... done
Rx clbufs 768 each of size 1660
ATHRS27: resetting s27
ATHRS27: s27 reset done
ATHRS27:Port status register read 2:7E
ATHRS27:S27 ATHR_PHY_FUNC_CONTROL (0):862
ATHRS27:S27 ATHR_PHY_ID1  (0) :4d
ATHRS27:S27 ATHR_PHY_SPEC_STATUS  (0) :10
ATHRS27:S27 ATHR_PHY_STATUS  (0) :7949
ATHRS27:S27 ATHR_PHY_FUNC_CONTROL (1):862
ATHRS27:S27 ATHR_PHY_ID1  (1) :4d
ATHRS27:S27 ATHR_PHY_SPEC_STATUS  (1) :10
ATHRS27:S27 ATHR_PHY_STATUS  (1) :7949
ATHRS27:S27 ATHR_PHY_FUNC_CONTROL (2):862
ATHRS27:S27 ATHR_PHY_ID1  (2) :4d
ATHRS27:S27 ATHR_PHY_SPEC_STATUS  (2) :10
ATHRS27:S27 ATHR_PHY_STATUS  (2) :7949
ATHRS27:S27 ATHR_PHY_FUNC_CONTROL (3):862
ATHRS27:S27 ATHR_PHY_ID1  (3) :4d
ATHRS27:S27 ATHR_PHY_SPEC_STATUS  (3) :10
ATHRS27:S27 ATHR_PHY_STATUS  (3) :7949
ATHRS27:S27 CPU_PORT_REGISTER :f0
ATHRS27:S27 PORT_STATUS_REGISTER0  :fe
ATHRS27:S27 PORT_STATUS_REGISTER1  :1280
ATHRS27:S27 PORT_STATUS_REGISTER2  :1280
ATHRS27:S27 PORT_STATUS_REGISTER3  :1280
ATHRS27:S27 PORT_STATUS_REGISTER4  :1280
ATHRS27:S27 PORT_CONTROL_REGISTER0 :4004
ATHRS27:S27 PORT_CONTROL_REGISTER1 :4004
ATHRS27:S27 PORT_CONTROL_REGISTER2 :4004
ATHRS27:S27 PORT_CONTROL_REGISTER3 :4004
ATHRS27:S27 PORT_CONTROL_REGISTER4 :4004
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
ATHRS27:athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
ATHRS27:athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
ATHRS27:athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
ATHRS27:athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
ATHRS27:athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
ATHRS27:athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
ATHRS27:athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
ATHRS27:athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
ae1 Verify MAC address CED7DFB2 2C280000
  sb = 28 2C B2 DF D7 CE
ATHRS27:ATHRS27:OPERATIONAL_MODE_REG0:40
ATHRS27:ATHRS27:REG 0x4-->:40
ATHRS27:ATHRS27:REG 0x2c-->:fe7f007f
ATHRS27:ATHRS27:REG 0x8-->:10000000
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
ATHRS27:athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
ATHRS27:athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
ae0 Verify MAC address CFD7DFB2 2C280000
  sb = 28 2C B2 DF D7 CF



                                      Version2.0
                            Software Platform for PNE2.2
              Copyright(C) 2001-2011 by TP-LINK TECHNOLOGIES CO., LTD.
                      Creation date: Jun  8 2013, 16:46:25
# Moduler MODULER-CONTROL: start working.


All config data size = 21740, srart address= 0x80481bd0.
Moduler MODULER-CONTROL: size = 16, srtart address = 0x80481bd0.
Moduler SYSTEM-LOG: size = 280, srtart address = 0x80481be0.
Moduler TDDP-AGENT: size = 0, srtart address = 0x80481cf8.
Moduler OEMDEF: size = 600, srtart address = 0x80481cf8.
Moduler BRIDGE: size = 0, srtart address = 0x80481f50.
Moduler ACCOUNT: size = 40, srtart address = 0x80481f50.
Moduler WEB-V4: size = 0, srtart address = 0x80481f78.
Moduler wizard: size = 0, srtart address = 0x80481f78.
Moduler OPMODE: size = 4, srtart address = 0x80481f78.
Moduler LAN: size = 16, srtart address = 0x80481f7c.
Moduler UPnP: size = 0, srtart address = 0x80481f8c.
Moduler WLAN: size = 3376, srtart address = 0x80481f8c.
Moduler MAC-CLONE: size = 0, srtart address = 0x80482cbc.
Moduler DHCPS: size = 1964, srtart address = 0x80482cbc.
Moduler IF-NAT: size = 0, srtart address = 0x80483468.
Moduler WAN: size = 4, srtart address = 0x80483468.
Moduler STATIC-IP: size = 32, srtart address = 0x8048346c.
Moduler DHCPC: size = 104, srtart address = 0x8048348c.
Moduler PPPoE: size = 600, srtart address = 0x804834f4.
Moduler VIRTSVR: size = 392, srtart address = 0x8048374c.
Moduler IGDV2: size = 4, srtart address = 0x804838d4.
Moduler DMZ-HOST: size = 8, srtart address = 0x804838d8.
Moduler STATIC-ROUTER: size = 328, srtart address = 0x804838e0.
Moduler Statistics: size = 20, srtart address = 0x80483a28.
Moduler AccessCtrl: size = 10860, srtart address = 0x80483a3c.
Moduler Security: size = 44, srtart address = 0x804864a8.
Moduler ARPBIND: size = 648, srtart address = 0x804864d4.
Moduler ADDITIONDNS: size = 0, srtart address = 0x8048675c.
Moduler DNS-PROXY: size = 0, srtart address = 0x8048675c.
Moduler DDNS: size = 1740, srtart address = 0x8048675c.
Moduler IPQOS: size = 572, srtart address = 0x80486e28.
Moduler LOGIN-PASSWORD: size = 0, srtart address = 0x80487064.
Moduler USER-REBOOT: size = 0, srtart address = 0x80487064.
Moduler RESET: size = 0, srtart address = 0x80487064.
Moduler DIAGNOSTIC: size = 0, srtart address = 0x80487064.
Moduler BAKNRESTORE: size = 0, srtart address = 0x80487064.
Moduler HTTP-FIRMWARE: size = 0, srtart address = 0x80487064.
Moduler IGMP: size = 4, srtart address = 0x80487064.
Moduler ANTI-SNIFFER: size = 0, srtart address = 0x80487068.
Moduler SNTPC: size = 84, srtart address = 0x80487068.
Moduler CPUSPY: size = 0, srtart address = 0x804870bc.

Moduler SYSTEM-LOG: start working.
Moduler TDDP-AGENT: start working.
Moduler OEMDEF: start working.
Moduler BRIDGE: start working.
Moduler ACCOUNT: start working.
Moduler WEB-V4: start working.
Moduler wizard: start working.
Moduler OPMODE: start working.
Moduler LAN: start working.
Moduler UPnP: start working.
Moduler WLAN: start working.
Restoring Cal data from Flash
correct CRC of the calData stored in flash is 0x9805952d
actual CRC of the calData stored in flash is 0x9805952d
802F23E0:  02 02 00 03 7F 4E C0 00 - 00 00 00 00 00 00 00 00      ...N.. ........
802F23F0:  00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 1F 00      ........ ........
802F2400:  33 02 00 00 00 00 04 00 - 62 00 4C 00 03 00 08 FF      3....... b.L.....
802F2410:  11 00 00 00 00 10 01 10 - 00 22 22 02 00 50 01 50      ........ .""..P.P
802F2420:  01 50 01 00 00 00 00 00 - 00 24 00 64 7D A4 AF 00      .P...... .$.d}...
802F2430:  FF 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F2440:  0E 0E 03 00 2C E2 00 02 - 0E 1C 80 C0 80 0C 80 C0      ....,... ........
802F2450:  80 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F2460:  00 00 00 00 00 00 00 00 - 00 00 70 89 A2 EA 00 86      ........ ..p.....
802F2470:  00 00 00 EA 00 87 00 00 - 00 EC 00 85 00 00 00 EA      ........ ........
802F2480:  00 80 00 00 00 EB 00 80 - 00 00 00 EC 00 8A 00 00      ........ ........
802F2490:  00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F24A0:  00 00 00 70 AC 70 89 AC - 70 89 AC 70 89 AC 28 28      ...p.p.. p..p..((
802F24B0:  28 28 28 28 28 28 28 28 - 22 1E 28 28 22 1E 28 28      (((((((( ".((".((
802F24C0:  22 1E 24 24 20 1E 1C 1A - 20 1E 1C 1A 20 20 1C 14      ".$$ ...  ...  ..
802F24D0:  24 24 20 1E 1C 1A 20 1E - 1C 1A 20 20 1C 14 24 24      $$ ... . ..  ..$$
802F24E0:  20 1E 1C 1A 20 1E 1C 1A - 20 20 1C 14 22 22 1E 1C       ... ...   ..""..
802F24F0:  1A 18 1E 1C 1A 18 20 20 - 1C 14 22 22 1E 1C 1A 18      ......   ..""....
802F2500:  1E 1C 1A 18 20 20 1C 14 - 22 22 1E 1C 1A 18 1E 1C      ....  .. ""......
802F2510:  1A 18 20 20 1C 14 11 12 - 15 17 41 42 45 47 31 32      ..  .... ..ABEG12
802F2520:  35 37 70 75 9D A2 70 75 - A2 FF 70 75 A2 FF 7A 7F      57pu..pu ..pu..
802F2530:  93 98 70 75 AC B8 70 75 - AC 00 70 75 AC 00 7A 7F      ..pu..pu ..pu..
802F2540:  93 A2 70 75 AC 00 70 75 - AC 00 70 75 AC 00 7A 7F      ..pu..pu ..pu..
802F2550:  93 A2 3C 7C 3C 3C 3C 7C - 3C 3C 7C 3C 3C 7C 7C 3C      ..<|<<<| <<|<<||<
802F2560:  3C 3C 3C 7C 3C 3C 3C 7C - 3C 3C 3C 7C 7C 3C 3C 7C      <<<|<<<| <<<||<<|
802F2570:  3C 3C 3C 7C 3C 3C 3C 7C - 3C 3C 3C 7C 7C 7C 3C 7C      <<<|<<<| <<<|||<|
802F2580:  7C 7C 10 01 00 00 22 22 - 02 00 00 00 00 00 00 00      ||...."" ........
802F2590:  00 00 00 00 00 00 44 00 - 00 00 00 00 00 FF 00 00      ......D. ........
802F25A0:  00 00 00 00 00 00 00 00 - 00 00 00 00 00 0E 0E 03      ........ ........
802F25B0:  00 2D E2 00 02 0E 1C E0 - E0 F0 0C E0 E0 F0 6C 00      .-...... ......l.
802F25C0:  00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F25D0:  00 00 00 00 00 00 00 4C - 54 68 78 8C A0 B9 CD 00      .......L Thx.....
802F25E0:  00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F25F0:  00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F2600:  00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F2610:  00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F2620:  00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F2630:  00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F2640:  00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F2650:  00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F2660:  00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 4C      ........ .......L
802F2670:  54 68 78 8C A0 B9 CD 4C - 58 68 8C B4 BD B9 CD 4C      Thx....L Xh.....L
802F2680:  58 68 8C B4 BD B9 CD 14 - 14 14 0A 14 14 14 0A 14      Xh...... ........
802F2690:  14 14 0A 14 14 14 0A 14 - 14 14 0A 14 14 14 0A 14      ........ ........
802F26A0:  14 14 0A 14 14 14 0A 14 - 14 0A 0A 00 00 0A 0A 00      ........ ........
802F26B0:  00 0A 0A 00 00 14 14 0A - 0A 00 00 0A 0A 00 00 0A      ........ ........
802F26C0:  0A 00 00 14 14 0A 0A 00 - 00 0A 0A 00 00 0A 0A 00      ........ ........
802F26D0:  00 14 14 0A 0A 00 00 0A - 0A 00 00 0A 0A 00 00 14      ........ ........
802F26E0:  14 0A 0A 00 00 0A 0A 00 - 00 0A 0A 00 00 14 14 0A      ........ ........
802F26F0:  0A 00 00 0A 0A 00 00 0A - 0A 00 00 14 14 0A 0A 00      ........ ........
802F2700:  00 0A 0A 00 00 0A 0A 00 - 00 14 14 0A 0A 00 00 0A      ........ ........
802F2710:  0A 00 00 0A 0A 00 00 14 - 14 0A 0A 00 00 0A 0A 00      ........ ........
802F2720:  00 0A 0A 00 00 14 14 0A - 0A 00 00 0A 0A 00 00 0A      ........ ........
802F2730:  0A 00 00 14 14 0A 0A 00 - 00 0A 0A 00 00 0A 0A 00      ........ ........
802F2740:  00 14 14 0A 0A 00 00 0A - 0A 00 00 0A 0A 00 00 14      ........ ........
802F2750:  14 0A 0A 00 00 0A 0A 00 - 00 0A 0A 00 00 14 14 0A      ........ ........
802F2760:  0A 00 00 0A 0A 00 00 0A - 0A 00 00 14 14 0A 0A 00      ........ ........
802F2770:  00 0A 0A 00 00 0A 0A 00 - 00 14 14 0A 0A 00 00 0A      ........ ........
802F2780:  0A 00 00 0A 0A 00 00 10 - 16 18 40 46 48 30 36 38      ........ ..@FH068
802F2790:  4C 5C 60 8C A0 B4 BD CD - 4C 5C 60 8C 90 B4 BD CD      L\`..... L\`.....
802F27A0:  4E 56 5E 66 8E 96 AE BF - 4C 50 5C 68 8C B4 FF FF      NV^f.... LP\h....
802F27B0:  4C 5C 8C B4 FF FF FF FF - 4E 5E 66 8E 9E AE FF FF      L\...... N^f.....
802F27C0:  4C 50 54 5C 8C A0 B4 BD - 4C 5C 68 8C 98 B4 BD CD      LPT\.... L\h.....
802F27D0:  4E 56 5E 8E 96 AE BF C7 - 7C 7C 7C 7C 7C 7C 7C 3C      NV^..... |||||||<
802F27E0:  7C 7C 7C 7C 7C 7C 7C 3C - 3C 7C 3C 7C 7C 7C 7C 7C      |||||||< <|<|||||
802F27F0:  3C 7C 7C 3C 7C 3C 3C 3C - 7C 7C 7C 3C 3C 3C 3C 3C      <||<|<<< |||<<<<<
802F2800:  7C 7C 7C 7C 7C 3C 3C 3C - 7C 7C 7C 7C 7C 7C 7C 7C      |||||<<< ||||||||
802F2810:  7C 7C 3C 7C 7C 7C 7C 3C - 7C 3C 7C 7C 7C 7C 3C 7C      ||<||||< |<||||<|
wlanSecFliterStart : install Wlan Sec filter.
Moduler MAC-CLONE: start working.
Moduler DHCPS: start working.
Moduler IF-NAT: start working.
Moduler WAN: start working.
Moduler STATIC-IP: start working.
Moduler DHCPC: start working.
add net 0.0.0.0: gateway 169.254.215.206
Moduler PPPoE: start working.
Moduler VIRTSVR: start working.
Moduler IGDV2: start working.
Moduler DMZ-HOST: start working.
Moduler STATIC-ROUTER: start working.
Moduler Statistics: start working.
Moduler AccessCtrl: start working.
Moduler Security: start working.
Moduler ARPBIND: start working.
Moduler ADDITIONDNS: start working.
Moduler DNS-PROXY: start working.
Moduler DDNS: start working.
Moduler IPQOS: start working.
Moduler LOGIN-PASSWORD: start working.
Moduler USER-REBOOT: start working.
Moduler RESET: start working.
Moduler DIAGNOSTIC: start working.
Moduler BAKNRESTORE: start working.
Moduler HTTP-FIRMWARE: start working.
Moduler IGMP: start working.
Moduler ANTI-SNIFFER: start working.
Moduler SNTPC: start working.
Moduler CPUSPY: start working.

Hello.
I just buy a router Mercury MW300R Version9.1 found it same as yours. and also hope it can update to openwrt,

just press enter then you see "Hit any key to stop autoboot" then you go to uboot menu.
Here you can find your memory details, whats helps to make own image for your device.

Based on this thread on dx.com, seems that this product is not a good option for using with OpenWrt.
http://club.dx.com/forums/forums.dx/threadid.1259800


Maybe after sime time on the market, they will do it.
But i think i will mod my wr703n´s to solve my problem and put the Fw300r to be a hotspot with the chinese interface.

SOC qca953x is not supported by openwrt currently,but i think it will be supported not so far.here is the TTL output of tp-link wr841n v9_en:

U-Boot 1.1.4 (Build from LSDK-9.5.3.16 at Dec 26 2013 - 17:11:56)

ap143 - Honey Bee 1.1

DRAM:   64 MB
ID read:0x10215
FLASH:  Spansion S25FL032P
SIZE:   4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
ath_gmac_enet_initialize: reset mask:0xc02200
Scorpion ---->S27 PHY*
S27 reg init
GMAC: cfg1 0x800c0000 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 4:0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4:0x10
eth0 up
Honey Bee ---->  MAC 1 S27 PHY*
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
GMAC: cfg1 0x800c0000 cfg2 0x7214
eth1: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 0:0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0:0x10
athrs27_phy_setup ATHR_PHY_CONTROL 1:0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1:0x10
athrs27_phy_setup ATHR_PHY_CONTROL 2:0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2:0x10
athrs27_phy_setup ATHR_PHY_CONTROL 3:0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3:0x10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x64c9a100
Router_Recovery_Mode=0
Hit any key to stop autoboot:  0
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

Booting QCA953x
榠nux version 2.6.31 (tplink@localhost.localdomain) (gcc version 4.3.3 (GCC) ) #23 Fri Nov 29 10:49:50 CST 2013
flash_size passed from bootloader = 4
Ram size passed from bootloader =67108864
CPU revision is: 00019374 (MIPS 24Kc)
ath_sys_frequency: cpu apb ddr apb cpu 550 ddr 391 ahb 195
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS0,115200 root=31:2 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),2816k(rootfs),64k(config),64k(art) mem=32M
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 56616k/65536k available (1558k kernel code, 8848k reserved, 379k data, 108k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 365.56 BogoMIPS (lpj=731136)
Mount-cache hash table entries: 512

****************ALLOC***********************
Packet mem: 80211220 (0x600000 bytes)
********************************************

NET: Registered protocol family 16
bio: create slab <bio-0> at 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 110
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
PPP generic driver version 2.4.2
NET: Registered protocol family 24
5 cmdlinepart partitions found on MTD device ath-nor0
Creating 5 MTD partitions on "ath-nor0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000120000 : "kernel"
0x000000120000-0x0000003e0000 : "rootfs"
0x0000003e0000-0x0000003f0000 : "config"
0x0000003f0000-0x000000400000 : "art"
->Oops: flash id 0x10215 .
Ooops, why the devices couldn't been initialed?
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
athwdt_init: Registering WDT success
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 108k freed
init started:  BusyBox v1.01 (2013.11.29-02:54+0000) multi-call binary
This Board use 2.6.31
xt_time: kernel timezone is -0000
nf_conntrack version 0.5.0 (1024 buckets, 5120 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
PPPoL2TP kernel driver, V1.0
PPTP driver version 0.8.3
insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/af_key.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/xfrm_user.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/xt_mark.ko': No such file or directory
/proc/sys/vfs_Now flash open!
Now flash open!
qca955x_GMAC: Length per segment 1536
953x_GMAC: qca953x_gmac_attach
Link Int Enabled
qca953x_set_gmac_caps  CHECK DMA STATUS
mac:1 Registering S27....
qca955x_GMAC: RX TASKLET - Pkts per Intr:32
qca955x_GMAC: Max segments per packet :   1
qca955x_GMAC: Max tx descriptor count :   512
qca955x_GMAC: Max rx descriptor count :   128
qca955x_GMAC: Mac capability flags    :   2D81
953x_GMAC: qca953x_gmac_attach
Link Int Enabled
qca953x_set_gmac_caps  CHECK DMA STATUS
mac:0 Registering S27....
qca955x_GMAC: RX TASKLET - Pkts per Intr:32
qca955x_GMAC: Max segments per packet :   1
qca955x_GMAC: Max tx descriptor count :   512
qca955x_GMAC: Max rx descriptor count :   128
qca955x_GMAC: Mac capability flags    :   2581

(none) mips #23 Fri Nov 29 10:49:50 CST 2013 (none)
(none) login: athr_gmac_ring_alloc Allocated 8192 at 0x8385a000
athr_gmac_ring_alloc Allocated 2048 at 0x838ad000
HONEYBEE ----> S27 PHY MDIO
ATHRS27: resetting s27
ATHRS27: s27 reset done
++++ athrs27_igmp_setup once
port0 vid is 0xb000b
port1 vid is 0x30003
port2 vid is 0x50005
port3 vid is 0x70007
port4 vid is 0x90009
++ PVID: 0x0000000b, bitmap: 0x0000001f
++ PVID: 0x00000003, bitmap: 0x0000001f
++ PVID: 0x00000005, bitmap: 0x0000001f
++ PVID: 0x00000007, bitmap: 0x0000001f
++ PVID: 0x00000009, bitmap: 0x0000001f
vtable vid: 0x00000002, bitmap 0x00000003
vtable vid: 0x00000004, bitmap 0x00000005
vtable vid: 0x00000006, bitmap 0x00000007
vtable vid: 0x00000008, bitmap 0x00000009
vtable vid: 0x0000000a, bitmap 0x0000000b
vtable vid: 0x0000000c, bitmap 0x0000000d
vtable vid: 0x0000000e, bitmap 0x0000000f
vtable vid: 0x00000010, bitmap 0x00000011
vtable vid: 0x00000012, bitmap 0x00000013
vtable vid: 0x00000014, bitmap 0x00000015
vtable vid: 0x00000016, bitmap 0x00000017
vtable vid: 0x00000018, bitmap 0x00000019
vtable vid: 0x0000001a, bitmap 0x0000001b
vtable vid: 0x0000001c, bitmap 0x0000001d
vtable vid: 0x0000001e, bitmap 0x0000001f
vtable vid: 0x00000020, bitmap 0x00000021
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
athr_gmac_ring_alloc Allocated 8192 at 0x83864000
athr_gmac_ring_alloc Allocated 2048 at 0x83a27000
HONEYBEE ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
device eth0 entered promiscuous mode
athr_gmac_ring_free Freeing at 0x83864000
athr_gmac_ring_free Freeing at 0x83a27000
athr_gmac_ring_alloc Allocated 8192 at 0x8385c000
athr_gmac_ring_alloc Allocated 2048 at 0x83a27000
HONEYBEE ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
Now flash open!
athr_gmac_ring_free Freeing at 0x8385a000
athr_gmac_ring_free Freeing at 0x838ad000
athr_gmac_ring_alloc Allocated 8192 at 0x838cc000
athr_gmac_ring_alloc Allocated 2048 at 0x838ad000
HONEYBEE ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
enet0 port4 up 100Mbps Full duplex
953x_GMAC: Enet Unit:0 PHY:4 is UP eth0  MII  100Mbps  full duplex
953x_GMAC: done cfg2 0x7115 ifctl 0x10000 miictrl 
Setting Drop CRC Errors, Pause Frames and Length Error frames
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
adf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_ahb: 9.5.3.16 (Atheros/multi-bss)
Enterprise mode: 0x03fc0000
Restoring Cal data from Flash
ath_get_caps[5856] rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps[5831] tx chainmask mismatch actual 3 sc_chainmak 0
wifi0: Atheros ???: mem=0xb8100000, irq=2
ath_pci: 9.5.3.16 (Atheros/multi-bss)
VAP device ath0 created
        DCS for CW interference mitigation:   0
        DCS for WLAN interference mitigation: 0

DES SSID SET=TP-LINK_137B00
ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
athr_gmac_ring_free Freeing at 0x838cc000
athr_gmac_ring_free Freeing at 0x838ad000
br0: port 1(eth0) entering disabled state
athr_gmac_ring_alloc Allocated 8192 at 0x83b24000
athr_gmac_ring_alloc Allocated 2048 at 0x838ad000
HONEYBEE ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
device ath0 entered promiscuous mode
br0: port 2(ath0) entering forwarding state
ieee80211_ioctl_siwmode: imr.ifm_active=1442432, new mode=3, valid=1
br0: port 2(ath0) entering disabled state

DES SSID SET=TP-LINK_137B00
br0: port 2(ath0) entering forwarding state
qca955x_GMAC: GE0 RX DMA ENABLE
blockWps_proc_write 802: write value = 0

The discussion might have continued from here.