Hello there,
I have generated rootfs and trying to load into freescale P1020RDB board.But error like kernel rebooting in 180 seconds is coming.Below i have mention the logs.
-------------------------------------------------------------------------------------------------------
Device: FSL_ESDHC
Manufacturer ID: 3
OEM: 5344
Name: SU04G
Tran Speed: 25000000
Rd Block Len: 512
SD version 2.0
High Capacity: Yes
Capacity: 3965190144
Bus Width: 4-bit
Loading file "/boot/uImage" from mmc device 0:1 (xxa1)
1524278 bytes read
Loading file "/boot/p1020rdb.dtb" from mmc device 0:1 (xxa1)
28288 bytes read
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 01000000 ...
Image Name: Linux-3.10.24
Created: 2014-01-01 7:16:12 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1524214 Bytes = 1.5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 00c00000
Booting using the fdt blob at 0xc00000
Uncompressing Kernel Image ... OK
Loading Device Tree to 00ff6000, end 00fffe7f ... OK
[ 0.000000] Using P1020 RDB machine description
[ 0.000000] Memory CAM mapping: 256/256/256 Mb, residual: 256Mb
[ 0.000000] Linux version 3.10.24 (root@nue) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r39163) ) #2 Wed Jan 1 12:46:07 IST 2014
[ 0.000000] bootconsole [udbg0] enabled
setup_arch: bootmem
mpc85xx_rdb_setup_arch()
[ 0.000000] mpc85xx_rdb_setup_arch: Could not find Quicc Engine node
[ 0.000000] MPC85xx RDB board from Freescale Semiconductor
arch: exit
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00000000-0x2fffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x2fffffff]
[ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 195072
[ 0.000000] Kernel command line: root=/dev/mmcblk0p1 rw rootdelay=30 console=ttyS0,115200
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 710276k/786432k available (2944k kernel code, 76156k reserved, 120k data, 180k bss, 132k init)
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xfffdf000..0xfffff000 : fixmap
[ 0.000000] * 0xfdffe000..0xfe000000 : early ioremap
[ 0.000000] * 0xf1000000..0xfdffe000 : vmalloc & ioremap
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:512 nr_irqs:512 16
[ 0.000000] mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000, max 1 CPUs
[ 0.000000] mpic: ISU size: 256, shift: 8, mask: ff
[ 0.000000] mpic: Initializing for 256 sources
[ 0.000000] mpc85xx_rdb_pic_init: Could not find qe-ic node
[ 0.000000] clocksource: timebase mult[1e000005] shift[24] registered
[ 0.006411] pid_max: default: 32768 minimum: 301
[ 0.011128] Mount-cache hash table entries: 512
[ 0.019974] NET: Registered protocol family 16
[ 0.036389] Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->1
[ 0.044256] PCI host bridge /pcie@ffe09000 (primary) ranges:
[ 0.049901] MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000
[ 0.057119] IO 0x00000000ffc10000..0x00000000ffc1ffff -> 0x0000000000000000
[ 0.064266] /pcie@ffe09000: PCICSRBAR @ 0xfff00000
[ 0.069513] Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->0
[ 0.077373] PCI host bridge /pcie@ffe0a000 ranges:
[ 0.082239] MEM 0x0000000080000000..0x000000009fffffff -> 0x0000000080000000
[ 0.089458] IO 0x00000000ffc00000..0x00000000ffc0ffff -> 0x0000000000000000
[ 0.096603] /pcie@ffe0a000: PCICSRBAR @ 0xfff00000
[ 0.114850] PCI: Probing PCI hardware
[ 0.118759] fsl-pci ffe09000.pcie: PCI host bridge to bus 0000:00
[ 0.124809] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.130965] pci_bus 0000:00: root bus resource [mem 0xa0000000-0xbfffffff]
[ 0.137839] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.143388] pci 0000:00:00.0: ignoring class 0x0b2000 (doesn't match header type 01)
[ 0.152099] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.162069] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.167627] fsl-pci ffe0a000.pcie: PCI host bridge to bus 0001:02
[ 0.173671] pci_bus 0001:02: root bus resource [io 0x20000-0x2ffff] (bus address [0x0000-0xffff])
[ 0.182617] pci_bus 0001:02: root bus resource [mem 0x80000000-0x9fffffff]
[ 0.189492] pci_bus 0001:02: root bus resource [bus 02-ff]
[ 0.195029] pci 0001:02:00.0: ignoring class 0x0b2000 (doesn't match header type 01)
[ 0.203005] pci 0001:02:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.211173] pci 0001:02:00.0: PCI bridge to [bus 03-ff]
[ 0.216526] pci 0000:00:00.0: BAR 9: can't assign mem pref (size 0x100000)
[ 0.223348] pci 0000:01:00.0: BAR 6: assigned [mem 0xa0080000-0xa00fffff pref]
[ 0.230558] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.235515] pci 0000:00:00.0: bridge window [io 0x0000-0xffff]
[ 0.241605] pci 0000:00:00.0: bridge window [mem 0xa0000000-0xbfffffff]
[ 0.248393] pci 0001:02:00.0: PCI bridge to [bus 03]
[ 0.253350] pci 0001:02:00.0: bridge window [io 0x20000-0x2ffff]
[ 0.259614] pci 0001:02:00.0: bridge window [mem 0x80000000-0x9fffffff]
[ 0.266394] Some PCI device resources are unassigned, try booting with pci=realloc
[ 0.273973] pci 0000:00:00.0: enabling device (0106 -> 0107)
[ 0.279629] pci 0001:02:00.0: enabling device (0106 -> 0107)
[ 0.289562] bio: create slab <bio-0> at 0
[ 0.295303] Switching to clocksource timebase
[ 0.301677] NET: Registered protocol family 2
[ 0.306364] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.313538] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.319997] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.326384] TCP: reno registered
[ 0.329554] UDP hash table entries: 512 (order: 1, 8192 bytes)
[ 0.335396] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes)
[ 0.341853] NET: Registered protocol family 1
[ 0.359290] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.365079] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.375683] msgmni has been set to 1515
[ 0.379672] io scheduler noop registered
[ 0.383513] io scheduler deadline registered (default)
[ 0.468117] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 0.475411] serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550A
[ 0.482170] console [ttyS0] enabled, bootconsole disabled
[ 0.482170] console [ttyS0] enabled, bootconsole disabled
[ 0.493518] serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550A
[ 0.501248] ffe04500.serial: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550
[ 0.508913] ffe04600.serial: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550
[ 0.516532] Generic RTC Driver v1.07
[ 0.522536] libphy: Freescale PowerQUICC MII Bus: probed
[ 0.529310] libphy: Freescale PowerQUICC MII Bus: probed
[ 0.537449] fsl-gianfar ethernet.1 eth0: mac: 00:04:9f:01:cf:04
[ 0.543411] fsl-gianfar ethernet.1 eth0: Running with NAPI enabled
[ 0.549617] fsl-gianfar ethernet.1 eth0: RX BD ring size for Q[0]: 256
[ 0.556168] fsl-gianfar ethernet.1 eth0: RX BD ring size for Q[1]: 256
[ 0.562719] fsl-gianfar ethernet.1 eth0: RX BD ring size for Q[2]: 256
[ 0.569271] fsl-gianfar ethernet.1 eth0: RX BD ring size for Q[3]: 256
[ 0.575821] fsl-gianfar ethernet.1 eth0: RX BD ring size for Q[4]: 256
[ 0.582373] fsl-gianfar ethernet.1 eth0: RX BD ring size for Q[5]: 256
[ 0.588924] fsl-gianfar ethernet.1 eth0: RX BD ring size for Q[6]: 256
[ 0.595475] fsl-gianfar ethernet.1 eth0: RX BD ring size for Q[7]: 256
[ 0.602027] fsl-gianfar ethernet.1 eth0: TX BD ring size for Q[0]: 256
[ 0.608578] fsl-gianfar ethernet.1 eth0: TX BD ring size for Q[1]: 256
[ 0.615129] fsl-gianfar ethernet.1 eth0: TX BD ring size for Q[2]: 256
[ 0.621681] fsl-gianfar ethernet.1 eth0: TX BD ring size for Q[3]: 256
[ 0.628233] fsl-gianfar ethernet.1 eth0: TX BD ring size for Q[4]: 256
[ 0.634783] fsl-gianfar ethernet.1 eth0: TX BD ring size for Q[5]: 256
[ 0.641334] fsl-gianfar ethernet.1 eth0: TX BD ring size for Q[6]: 256
[ 0.647885] fsl-gianfar ethernet.1 eth0: TX BD ring size for Q[7]: 256
[ 0.656364] fsl-gianfar ethernet.2 eth1: mac: 00:04:9f:01:cf:05
[ 0.662324] fsl-gianfar ethernet.2 eth1: Running with NAPI enabled
[ 0.668529] fsl-gianfar ethernet.2 eth1: RX BD ring size for Q[0]: 256
[ 0.675080] fsl-gianfar ethernet.2 eth1: RX BD ring size for Q[1]: 256
[ 0.681631] fsl-gianfar ethernet.2 eth1: RX BD ring size for Q[2]: 256
[ 0.688183] fsl-gianfar ethernet.2 eth1: RX BD ring size for Q[3]: 256
[ 0.694734] fsl-gianfar ethernet.2 eth1: RX BD ring size for Q[4]: 256
[ 0.701285] fsl-gianfar ethernet.2 eth1: RX BD ring size for Q[5]: 256
[ 0.707836] fsl-gianfar ethernet.2 eth1: RX BD ring size for Q[6]: 256
[ 0.714386] fsl-gianfar ethernet.2 eth1: RX BD ring size for Q[7]: 256
[ 0.720938] fsl-gianfar ethernet.2 eth1: TX BD ring size for Q[0]: 256
[ 0.727489] fsl-gianfar ethernet.2 eth1: TX BD ring size for Q[1]: 256
[ 0.734040] fsl-gianfar ethernet.2 eth1: TX BD ring size for Q[2]: 256
[ 0.740591] fsl-gianfar ethernet.2 eth1: TX BD ring size for Q[3]: 256
[ 0.747142] fsl-gianfar ethernet.2 eth1: TX BD ring size for Q[4]: 256
[ 0.753693] fsl-gianfar ethernet.2 eth1: TX BD ring size for Q[5]: 256
[ 0.760245] fsl-gianfar ethernet.2 eth1: TX BD ring size for Q[6]: 256
[ 0.766796] fsl-gianfar ethernet.2 eth1: TX BD ring size for Q[7]: 256
[ 0.775210] fsl-gianfar ethernet.3 eth2: mac: 00:04:9f:01:cf:06
[ 0.781175] fsl-gianfar ethernet.3 eth2: Running with NAPI enabled
[ 0.787379] fsl-gianfar ethernet.3 eth2: RX BD ring size for Q[0]: 256
[ 0.793931] fsl-gianfar ethernet.3 eth2: RX BD ring size for Q[1]: 256
[ 0.800483] fsl-gianfar ethernet.3 eth2: RX BD ring size for Q[2]: 256
[ 0.807034] fsl-gianfar ethernet.3 eth2: RX BD ring size for Q[3]: 256
[ 0.813585] fsl-gianfar ethernet.3 eth2: RX BD ring size for Q[4]: 256
[ 0.820137] fsl-gianfar ethernet.3 eth2: RX BD ring size for Q[5]: 256
[ 0.826688] fsl-gianfar ethernet.3 eth2: RX BD ring size for Q[6]: 256
[ 0.833239] fsl-gianfar ethernet.3 eth2: RX BD ring size for Q[7]: 256
[ 0.839791] fsl-gianfar ethernet.3 eth2: TX BD ring size for Q[0]: 256
[ 0.846341] fsl-gianfar ethernet.3 eth2: TX BD ring size for Q[1]: 256
[ 0.852893] fsl-gianfar ethernet.3 eth2: TX BD ring size for Q[2]: 256
[ 0.859444] fsl-gianfar ethernet.3 eth2: TX BD ring size for Q[3]: 256
[ 0.865996] fsl-gianfar ethernet.3 eth2: TX BD ring size for Q[4]: 256
[ 0.872548] fsl-gianfar ethernet.3 eth2: TX BD ring size for Q[5]: 256
[ 0.879098] fsl-gianfar ethernet.3 eth2: TX BD ring size for Q[6]: 256
[ 0.885650] fsl-gianfar ethernet.3 eth2: TX BD ring size for Q[7]: 256
[ 0.892400] ucc_geth_driver: QE UCC Gigabit Ethernet Controller
[ 0.898856] TCP: cubic registered
[ 0.902204] NET: Registered protocol family 17
[ 0.906740] 8021q: 802.1Q VLAN Support v1.8
[ 0.912203] Waiting 30sec before mounting root device...
[ 30.919748] VFS: Cannot open root device "mmcblk0p1" or unknown-block(0,0): error -6
[ 30.927523] Please append a correct "root=" boot option; here are the available partitions:
[ 30.935902] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 30.944184] CPU: 0 PID: 1 Comm: swapper Not tainted 3.10.24 #2
[ 30.950022] Call Trace:
[ 30.952487] [ef833df0] [c0006914] show_stack+0x50/0x170 (unreliable)
[ 30.958872] [ef833e30] [c023b6f0] dump_stack+0x24/0x34
[ 30.964024] [ef833e40] [c0239dcc] panic+0xc8/0x210
[ 30.968827] [ef833ea0] [c02bfcfc] mount_block_root+0x228/0x2e0
[ 30.974674] [ef833ef0] [c02bff88] prepare_namespace+0x16c/0x1ac
[ 30.980606] [ef833f00] [c02bf964] kernel_init_freeable+0x1a8/0x1c0
[ 30.986799] [ef833f30] [c0002730] kernel_init+0x14/0x11c
[ 30.992126] [ef833f40] [c000c4bc] ret_from_kernel_thread+0x5c/0x64
[ 30.998316] Rebooting in 180 seconds..
------------------------------------------------------------------------------------------------------------------
Please guys help me out of this problem.
Regards
Suman Pandit