OpenWrt Forum Archive

Topic: Kingston Mobilelite MLW221

The content of this topic has been archived between 14 Apr 2018 and 27 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

@susanne76

You have to cross TX/RX, TX on RX and RX on TX ;-) If not, screen stays black.

Hi, sorry to resurrecting a dead thread, but hopefully someone is still subscribed to it. The ticketing system doesn't appear to work, so I'll try my luck here.

I've recently restarted using my old Kingston MobileLite Wireless MLW221 router, and decided to build and flash the latest stable OpenWrt release (17.01.4). The device was last flashed with Chaos Calmer r49363, and it worked without any problems. Now, on the latest revision, it outputs a lot of "jffs2: Newly-erased block contained word 0xdec0adde at offset x", rendering the device unusable due to lack of persistence of setting after a reset. I've tried multiple time to re-flash it, by flashing the Kingston stock image via TFTP, then the OpenWrt one via TFTP, procedure that is identical for both the Chaos Calmer and 17.01.4. As seen in the logs, the old build boots up without any issues, while the newer one doesn't. I've tried the buildbots' image, building my own bare-bone, and fully packed, but still the same result. What can I try to fix this issue? Thank you!

Stock log:

U-Boot 1.1.3 (Apr 10 2013 - 15:50:37)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: 1 20 18 4d 1 (20184d01)
find flash: S25FL129P
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Apr 10 2013  Time:15:50:37
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size =64 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.                     0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
   Image Name:   Linux Kernel Image
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    5510365 Bytes =  5.3 MB
   Load Address: 80000000
   Entry Point:  8000c310
raspi_read: from:50040 len:5414dd
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c310) ...
## Giving linux memsize in MB, 64

Starting kernel ...


LINUX started...

 THIS IS ASIC
Linux version 2.6.36+ (root@CVS2) (gcc version 3.4.2) #2 Wed Aug 13 14:27:07 CST 2014

 The CPU feqenuce set to 580 MHz
 PCIE: bypass PCIe DLL.
 PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
 disable all power about PCIe
 PCIE: PLL power down for MT7620N
CPU revision is: 00019650 (MIPS 24Kc)
Determined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=ttyS0
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=00036bbf
Readback ErrCtl register=00036bbf
Memory: 55400k/65536k available (4731k kernel code, 10136k reserved, 852k data, 3736k init, 0k highmem)
NR_IRQS:128
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RT3xxx EHCI/OHCI init.
JFFS2 version 2.2 (NAND) (SUMMARY) (ZLIB) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
fuse init (API version 7.15)
msgmni has been set to 108
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
Ralink gpio driver initialized
led=43, on=5, off=5, blinks,=4000, reset=1, time=4000
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
brd: module loaded
flash0: started
deice id : 1 20 18 4d 1 (20184d01)
S25FL129P(01 20184d01) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (0M) .erasesize = 0x00000010 (0K) .numeraseregions = 65536
Creating 5 MTD partitions on "raspi":
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000fb0000 : "Kernel"
0x000000fb0000-0x000001000000 : "User_CFG"
rdm_major = 253
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43762077
Ralink APSoC Ethernet Driver Initilization. v3.0  256 rx/tx descriptors allocated, mtu = 1500!
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43762077
PROC INIT OK!
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5


=== pAd = c0198000, size = 807960 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
AP Driver version-2.7.1.2
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
MTK MSDC device init.
mtk-sd: MediaTek MT6575 MSDC Driver
nf_conntrack version 0.5.0 (865 buckets, 3460 max)
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
GRE over IPv4 demultiplexor driver
gre: can't add protocol
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
TCP cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
msdc0 -> ops_get_cd return<0> <- msdc_ops_get_cd() : L<2273> PID<kworker/u:1><0x16>
Freeing unused kernel memory: 3736k freed
init started: BusyBox v1.12.1 (2014Algorithmics/MIPS FPU Emulator v1.5
-08-13 14:16:38 CST)
starting pid 31, tty '': '/etc_ro/rcS'
ufsd: module license 'Commercial product' taints kernel.
Disabling lock debugging due to kernel taint
ufsd:: trace mask set to 0000000f
ufsd: driver (lke_8.9.0 lke_8.9.0_r225793_b93, LBD=ON, delalloc, ioctl, ugm, sd(1), wb, tr) loaded at c0348000
NTFS support included
exFAT/TexFAT support included
optimized: speed
Build_for__Kingston_wifi_card_reader_k2.6.36_2013-03-22_lke_8.9.0_r225793_b93

ufsd: exfat can't store dates before Jan 1, 1980. Please update current date
usb 1-1: new high speed USB device using rt3xxx-ehci and address 2
devpts: called with bogus options
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 3 ports detected
usb 1-1.1: new high speed USB device using rt3xxx-ehci and address 3
scsi0 : usb-storage 1-1.1:1.0
scsi 0:0:0:0: Direct-Access     Generic  STORAGE DEVICE   0208 PQ: 0 ANSI: 0
sd 0:0:0:0: [sda] Attached SCSI removable disk
***** sda no need2 *****
Welcome to
    _______  _______  ___     __  ____   _  _   ___
    |  ___  \|   __  ||   |   |__||    \ | || | /  /
    | |___| ||  |__| ||   |__  __ |     \| || |/  /
    |   _   /|   _   ||      ||  || |\     ||     \
    |__| \__\|__| |__||______||__||_| \____||_|\___\

                     =System Architecture Department=

[check_jffs]80 : JFFS_OK
led=11, on=1, off=4000, blinks,=1, reset=1, time=4000
semget err:: No such fled=7, on=1, off=4000, blinks,=1, reset=1, time=4000
ile or directory
Set: phy[0].reg[0] = 3100
Set: phy[1].reg[0] = 3100
Set: phy[2].reg[0] = 3100
Set: phy[3].reg[0] = 3100
Set: phy[4].reg[0] = 3100
nvram_init: INFO=>nvram MAC initialized successfully!
==>shm_init()!!
check_shm_hash: Check shm hash value
nvram_init: INFO=>nvram conf initialized successfully!
nvram_init: INFO=> RAM CONF successful created!
nvram_init: INFO=> RC.CONF successful created!
---------------- Get WLAN MAC 00:26:b7:80:1e:90---------------
switch reg write offset=94, value=1000
switch reg write offset=2004, value=ff0003
switch reg write offset=2104, value=ff0003
switch reg write offset=2204, value=ff0003
switch reg write offset=2304, value=ff0003
switch reg write offset=2404, value=ff0003
switch reg write offset=2504, value=ff0003
switch reg write offset=2010, value=810000c0
switch reg write offset=2110, value=810000c0
switch reg write offset=2210, value=810000c0
switch reg write offset=2310, value=810000c0
switch reg write offset=2410, value=810000c0
switch reg write offset=2510, value=810000c0
switch reg write offset=2610, value=81000000
switch reg write offset=2710, value=81000000
switch reg write offset=2604, value=20ff0003
switch reg write offset=2704, value=20ff0003
Special Tag Disabled
switch reg write offset=2610, value=81000000
switch reg write ofRaeth v3.0 (fTaskletse,SkbRecyclet)
=2014
phy_tx_ring = 0x024b2000, tx_ring = 0xa24b2000

phy_rx_ring0 = 0x024b3000, rx_ring0 = 0xa24b3000
SMACCR1 -- : 0x00000026
SMACCR0 -- : 0xb7801e90
, ESW: Link Status Changed - Port0 Link UP
valCDMA_CSG_CFG = 81000000
ueGDMA1_FWD_CFG = 20710000
=10001
switch reg write offset=2114, value=10001
switch reg write offset=2214, value=10001
switch reg write offset=2314, value=10001
switch reg write offset=2414, value=10002
switch reg write offset=2514, value=10001
REG_ESW_WT_MAC_ATC is 0x7ff0002
done.
ifconfig: SIOCSIFHWADDR: No such device
ifconfig: ioctl 0x8913 failed: No such device
device vlan0001 entered promiscuous mode
device eth2 entered promiscuous mode
input_access=[3]
echo 3 > /proc/lan_wlan_access_controller
sh: can't create /proc/lan_wlan_access_controlbr0: port 1(vlan0001) entering learning state
lebr0: port 1(vlan0001) entering learning state
r: nonexistent directory
Fri Jan  1 00:00:00 GMT 2010
/etc_ro/rcS: line 138: wd_keepalive: not found
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
iptables v1.4.10:
The "nat" table is not intended for filtering, the use of DROP is therefore inhibited.


Try `iptables -h' or 'iptables --help' for more information.
ifconfig: ioctl 0x8913 failed: No such device
interface ra2 does not exist!
ifconfig: ioctl 0x8913 failed: No such device
interface ra2 does not exist!
[Enter Test] in wlan_led_ctrl.c main()
.insmod: ipv6passthru.ko: module not found
/usr/shell/dnsmasq.sh stop ok
dnsmasq: read /etc/hosts - 2 addresses
dnsmasq: read /etc/hosts - 2 addresses
dnsmasq: [truncated] m
/usr/shell/dnsmasq.sh start ok
sh: /usr/sbin/miniupnpd: not found
/usr/shell/udhcpd.sh config ok
/usr/shell/udhcpd.sh start ok

***** g_wl_interface = ra0 ******

MAX_NUM_SESSIONS : 5; NUM_SEES: 64
CAN'T FIND scsi_count
***** sda no need2 *****
aa
CAN'T FIND usb_default_path
CAN'T FIND WDS_AOSS_Running
/etc_ro/rcS: line 243: /usr/local/apache2/bin/htpasswd: not found
ls: /media/*/mlwfw_v*.*.*.bin: No such file or directory
killall: DMS: no process killed
killall: smbd: no process killed
killall: nmbd: no process killed
kill samba server firsthello, samba!
startsmbfilepwent_internal: file /tmp/samba/private/smbpasswd did not exist. File successfully created.
User guest password set to none.
new GPIO mode
ls: /media/*/gemtek_easytest.txt: No such file or directory
starting pid 8262, tty '/dev/ttyS1': '/bin/sh'


BusyBox v1.12.1 (2014-08-13 14:16:38 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

# CAN'T FIND dlna_hw_nat_disable
main(205) ::
DMS_Create()
DLNA DMS: UUID=[aaab4c54-ea1b-1885-b390-0026b7801e90]
IP Address List: 192.168.200.254

Chaos Calmer log:

U-Boot 1.1.3 (Apr 10 2013 - 15:50:37)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: 1 20 18 4d 1 (20184d01)
find flash: S25FL129P
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Apr 10 2013  Time:15:50:37
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size =64 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.                     0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
   Image Name:   MIPS OpenWrt Linux-3.18.29
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1138945 Bytes =  1.1 MB
   Load Address: 80000000
   Entry Point:  80000000
raspi_read: from:50040 len:116101
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 3.18.29 (pmv@pmv-vb) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49363) ) #1 Thu May 26 14:20:24 EEST 2016
[    0.000000] Board has DDR2
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7620N ver:2 eco:3
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[    0.000000] MIPS: machine is Kingston MLW221
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00036bbf
[    0.000000] Readback ErrCtl register=00036bbf
[    0.000000] Memory: 61372K/65536K available (2516K kernel code, 123K rwdata, 516K rodata, 164K init, 186K bss, 4164K reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 580MHz
[    0.000000] systick: running - mult: 214748, shift: 32
[    0.010000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.070000] pid_max: default: 32768 minimum: 301
[    0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090000] pinctrl core: initialized pinctrl subsystem
[    0.100000] NET: Registered protocol family 16
[    0.120000] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.130000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.140000] rt2880_gpio 10000660.gpio: registering 32 gpios
[    0.150000] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[    0.160000] rt2880_gpio 10000688.gpio: registering 1 gpios
[    0.170000] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[    0.180000] Switched to clocksource systick
[    0.190000] NET: Registered protocol family 2
[    0.190000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.210000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.220000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.230000] TCP: reno registered
[    0.240000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.250000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.260000] NET: Registered protocol family 1
[    0.270000] rt-timer 10000100.timer: maximum frequency is 2441Hz
[    0.290000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.310000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.320000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.340000] msgmni has been set to 119
yS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a 16550A
[    0.420000] console [ttyS0] enabled
[    0.420000] console [ttyS0] enabled
[    0.440000] bootconsole [early0] disabled
[    0.440000] bootconsole [early0] disabled
[    0.460000] m25p80 spi32766.0: s25fl129p1 (16384 Kbytes)
[    0.470000] 5 ofpart partitions found on MTD device spi32766.0
[    0.480000] Creating 5 MTD partitions on "spi32766.0":
[    0.490000] 0x000000000000-0x000000030000 : "u-boot"
[    0.500000] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.510000] 0x000000040000-0x000000050000 : "factory"
[    0.520000] 0x000000050000-0x000000fb0000 : "firmware"
[    0.650000] 2 uimage-fw partitions found on MTD device firmware
[    0.670000] 0x000000050000-0x000000166141 : "kernel"
[    0.680000] 0x000000166141-0x000000fb0000 : "rootfs"
[    0.690000] mtd: device 5 (rootfs) set to be root filesystem
[    0.700000] 1 squashfs-split partitions found on MTD device rootfs
[    0.710000] 0x000000400000-0x000000fb0000 : "rootfs_data"
[    0.720000] 0x000000fb0000-0x000001000000 : "user-config"
[    0.740000] ralink_soc_eth 10100000.ethernet eth0 (uninitialized): port 0 link up (100Mbps/Full duplex)
[    0.760000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver
[    0.770000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
[    0.780000] rt2880_wdt 10000120.watchdog: Initialized
[    0.790000] TCP: cubic registered
[    0.800000] NET: Registered protocol family 17
[    0.810000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.830000] 8021q: 802.1Q VLAN Support v1.8
[    0.860000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    0.880000] Freeing unused kernel memory: 164K (80317000 - 80340000)
[    3.410000] init: Console is alive
[    3.410000] init: - watchdog -
[    6.870000] usbcore: registered new interface driver usbfs
[    6.880000] usbcore: registered new interface driver hub
[    6.890000] usbcore: registered new device driver usb
[    6.940000] SCSI subsystem initialized
[    6.960000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    6.970000] ehci-platform: EHCI generic platform driver
[    6.990000] phy phy-usbphy.0: remote usb device wakeup disabled
[    7.000000] phy phy-usbphy.0: UTMI 16bit 30MHz
[    7.010000] ehci-platform 101c0000.ehci: EHCI Host Controller
[    7.020000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[    7.040000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[    7.070000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[    7.080000] hub 1-0:1.0: USB hub found
[    7.090000] hub 1-0:1.0: 1 port detected
[    7.100000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    7.110000] ohci-platform: OHCI generic platform driver
[    7.120000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[    7.140000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[    7.150000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[    7.220000] hub 2-0:1.0: USB hub found
[    7.230000] hub 2-0:1.0: 1 port detected
[    7.240000] usbcore: registered new interface driver usb-storage
[    7.410000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    7.450000] init: - preinit -
[    7.630000] hub 1-1:1.0: USB hub found
[    7.640000] hub 1-1:1.0: 3 ports detected
[    8.110000] 8021q: adding VLAN 0 to HW filter on device eth0
[    8.140000] random: procd urandom read with 13 bits of entropy available
[    8.160000] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    8.290000] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[    8.300000] scsi host0: usb-storage 1-1.1:1.0
[    9.310000] scsi 0:0:0:0: Direct-Access     Generic  STORAGE DEVICE   0208 PQ: 0 ANSI: 0
[    9.470000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   11.300000] mount_root: loading kmods from internal overlay
[   12.420000] block: attempting to load /etc/config/fstab
[   12.430000] block: unable to load configuration (fstab: Entry not found)
[   12.450000] block: no usable configuration
[   12.460000] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[   12.490000] procd: - early -
[   12.500000] procd: - watchdog -
[   13.510000] procd: - ubus -
[   14.530000] procd: - init -
Please press Enter to activate this console.
[   15.410000] NET: Registered protocol family 10
[   15.430000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   15.460000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   15.480000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
[   15.490000] Backport generated by backports.git backports-20151218-0-g2f58d9d
[   15.510000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.530000] nf_conntrack version 0.5.0 (961 buckets, 3844 max)
[   15.560000] usbcore: registered new interface driver ums-alauda
[   15.580000] usbcore: registered new interface driver ums-cypress
[   15.590000] usbcore: registered new interface driver ums-datafab
[   15.600000] usbcore: registered new interface driver ums-freecom
[   15.620000] usbcore: registered new interface driver ums-isd200
[   15.630000] usbcore: registered new interface driver ums-jumpshot
[   15.650000] usbcore: registered new interface driver ums-karma
[   15.660000] usbcore: registered new interface driver ums-sddr09
[   15.680000] usbcore: registered new interface driver ums-sddr55
[   15.690000] usbcore: registered new interface driver ums-usbat
[   15.720000] xt_time: kernel timezone is -0000
[   15.820000] PPP generic driver version 2.4.2
[   15.840000] NET: Registered protocol family 24
[   15.880000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0500 detected
[   15.890000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[   25.300000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   25.330000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   25.340000] jffs2_build_filesystem(): erasing all blocks after the end marker...
[   25.610000] 8021q: adding VLAN 0 to HW filter on device eth0
[   25.640000] device eth0.1 entered promiscuous mode
[   25.650000] device eth0 entered promiscuous mode
[   25.700000] br-lan: port 1(eth0.1) entered forwarding state
[   25.710000] br-lan: port 1(eth0.1) entered forwarding state
[   27.710000] br-lan: port 1(eth0.1) entered forwarding state



BusyBox v1.23.2 (2016-05-26 14:09:52 EEST) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 CHAOS CALMER (Chaos Calmer, r49363)
 -----------------------------------------------------
  * 1 1/2 oz Gin            Shake with a glassful
  * 1/4 oz Triple Sec       of broken ice and pour
  * 3/4 oz Lime Juice       unstrained into a goblet.
  * 1 1/2 oz Orange Juice
  * 1 tsp. Grenadine Syrup
 -----------------------------------------------------
root@OpenWrt:/#

17.01.4 log:

U-Boot 1.1.3 (Apr 10 2013 - 15:50:37)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: 1 20 18 4d 1 (20184d01)
find flash: S25FL129P
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Apr 10 2013  Time:15:50:37
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size =64 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.                     0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
   Image Name:   MIPS LEDE Linux-4.4.92
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1262493 Bytes =  1.2 MB
   Load Address: 80000000
   Entry Point:  80000000
raspi_read: from:50040 len:13439d
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 4.4.92 (pmv@pmv-vb) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3560-79f57e422d) ) #0 Tue Oct 17 17:46:20 2017
[    0.000000] Board has DDR2
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7620N ver:2 eco:3
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[    0.000000] MIPS: machine is Kingston MLW221
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00036bbf
[    0.000000] Readback ErrCtl register=00036bbf
[    0.000000] Memory: 60776K/65536K available (2903K kernel code, 137K rwdata, 696K rodata, 160K init, 203K bss, 4760K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 580MHz
[    0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[    0.000000] systick: enable autosleep mode
[    0.000000] systick: running - mult: 214748, shift: 32
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[    0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[    0.015450] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.080607] pid_max: default: 32768 minimum: 301
[    0.089931] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.102943] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.122342] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.141837] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.154085] pinctrl core: initialized pinctrl subsystem
[    0.165079] NET: Registered protocol family 16
[    0.191888] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.202914] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.215333] rt2880_gpio 10000660.gpio: registering 32 gpios
[    0.226314] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[    0.238743] rt2880_gpio 10000688.gpio: registering 1 gpios
[    0.249555] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[    0.263238] clocksource: Switched to clocksource systick
[    0.275178] NET: Registered protocol family 2
[    0.284638] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.298418] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.311004] TCP: Hash tables configured (established 1024 bind 1024)
[    0.323730] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.335265] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.347985] NET: Registered protocol family 1
[    0.360464] rt-timer 10000100.timer: maximum frequency is 1220Hz
[    0.373432] Crashlog allocated RAM at address 0x3f00000
[    0.399052] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.410580] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.432756] io scheduler noop registered
[    0.440470] io scheduler deadline registered (default)
[    0.450885] ralink-usb-phy usbphy: invalid resource
[    0.461143] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.474868] console [ttyS0] disabled
[    0.481859] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[    0.501630] console [ttyS0] enabled
[    0.501630] console [ttyS0] enabled
[    0.515407] bootconsole [early0] disabled
[    0.515407] bootconsole [early0] disabled
[    0.536004] spi spi0.0: force spi mode3
[    0.544238] m25p80 spi0.0: s25fl128s (16384 Kbytes)
[    0.554035] 5 ofpart partitions found on MTD device spi0.0
[    0.564969] Creating 5 MTD partitions on "spi0.0":
[    0.574528] 0x000000000000-0x000000030000 : "u-boot"
[    0.586184] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.598654] 0x000000040000-0x000000050000 : "factory"
[    0.610562] 0x000000050000-0x000000fb0000 : "firmware"
[    1.917983] 2 uimage-fw partitions found on MTD device firmware
[    1.929825] 0x000000050000-0x0000001843dd : "kernel"
[    1.941362] 0x0000001843dd-0x000000fb0000 : "rootfs"
[    1.953120] mtd: device 5 (rootfs) set to be root filesystem
[    1.964608] 1 squashfs-split partitions found on MTD device rootfs
[    1.976945] 0x000000472000-0x000000fb0000 : "rootfs_data"
[    1.989574] 0x000000fb0000-0x000001000000 : "user-config"
[    2.006064] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 0 link up (100Mbps/Full duplex)
[    2.024506] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[    2.037110] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[    2.054157] rt2880_wdt 10000120.watchdog: Initialized
[    2.065782] NET: Registered protocol family 10
[    2.077952] NET: Registered protocol family 17
[    2.086974] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    2.112137] 8021q: 802.1Q VLAN Support v1.8
[    2.132755] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    2.147739] Freeing unused kernel memory: 160K
[    4.164183] init: Console is alive
[    4.171159] init: - watchdog -
[    7.329250] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    7.442745] usbcore: registered new interface driver usbfs
[    7.453858] usbcore: registered new interface driver hub
[    7.464587] usbcore: registered new device driver usb
[    7.515096] SCSI subsystem initialized
[    7.529558] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.544395] ehci-platform: EHCI generic platform driver
[    7.565186] phy phy-usbphy.0: remote usb device wakeup disabled
[    7.576996] phy phy-usbphy.0: UTMI 16bit 30MHz
[    7.585884] ehci-platform 101c0000.ehci: EHCI Host Controller
[    7.597394] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[    7.613309] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[    7.631817] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[    7.645453] hub 1-0:1.0: USB hub found
[    7.653375] hub 1-0:1.0: 1 port detected
[    7.664707] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    7.678684] ohci-platform: OHCI generic platform driver
[    7.689441] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[    7.703052] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[    7.718928] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[    7.753659] hub 2-0:1.0: USB hub found
[    7.761601] hub 2-0:1.0: 1 port detected
[    7.772213] uhci_hcd: USB Universal Host Controller Interface driver
[    7.797756] MTK MSDC device init.
[    7.804674] mtk-sd: MediaTek MT6575 MSDC Driver
[    7.817253] sdhci: Secure Digital Host Controller Interface driver
[    7.829701] sdhci: Copyright(c) Pierre Ossman
[    7.840441] sdhci-pltfm: SDHCI platform and OF driver helper
[    7.857186] usbcore: registered new interface driver usb-storage
[    7.873880] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    7.893001] init: - preinit -
[    7.986925] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    8.893330] random: procd: uninitialized urandom read (4 bytes read, 14 bits of entropy available)
[    8.912022] hub 1-1:1.0: USB hub found
[    8.932628] hub 1-1:1.0: 3 ports detected
[    9.826361] 8021q: adding VLAN 0 to HW filter on device eth0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.960143] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
[   10.014075] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[   10.027914] scsi host0: usb-storage 1-1.1:1.0
[   10.378885] scsi 0:0:0:0: Direct-Access     Generic  STORAGE DEVICE   0208 PQ: 0 ANSI: 0
[   10.449871] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   11.234198] mount_root: loading kmods from internal overlay
[   11.275019] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   11.291503] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   23.876947] block: attempting to load /etc/config/fstab
[   23.890008] block: unable to load configuration (fstab: Entry not found)
[   23.903669] block: no usable configuration
[   23.913134] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[   23.932534] urandom-seed: Seed file not found (/etc/urandom.seed)
[   24.068138] procd: - early -
[   24.075119] procd: - watchdog -
[   24.767674] procd: - watchdog -
[   24.774486] procd: - ubus -
[   24.810693] random: ubusd: uninitialized urandom read (4 bytes read, 48 bits of entropy available)
[   24.829498] random: ubusd: uninitialized urandom read (4 bytes read, 48 bits of entropy available)
[   24.847671] random: ubusd: uninitialized urandom read (4 bytes read, 48 bits of entropy available)
[   24.866207] random: ubusd: uninitialized urandom read (4 bytes read, 48 bits of entropy available)
[   24.884249] random: ubusd: uninitialized urandom read (4 bytes read, 48 bits of entropy available)
[   24.902529] random: ubusd: uninitialized urandom read (4 bytes read, 48 bits of entropy available)
[   24.920812] random: ubusd: uninitialized urandom read (4 bytes read, 48 bits of entropy available)
[   24.939408] procd: - init -
Please press Enter to activate this console.
[   25.267757] kmodloader: loading kernel modules from /etc/modules.d/*
[   25.314501] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   25.343896] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[   25.359979] Backport generated by backports.git backports-20160324-13-g24da7d3c
[   25.451012] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   25.472509] ip_tables: (C) 2000-2006 Netfilter Core Team
[   25.497705] nf_conntrack version 0.5.0 (952 buckets, 3808 max)
[   25.552231] usbcore: registered new interface driver ums-alauda
[   25.567313] usbcore: registered new interface driver ums-cypress
[   25.582544] usbcore: registered new interface driver ums-datafab
[   25.597604] usbcore: registered new interface driver ums-freecom
[   25.612848] usbcore: registered new interface driver ums-isd200
[   25.628014] usbcore: registered new interface driver ums-jumpshot
[   25.643247] usbcore: registered new interface driver ums-karma
[   25.658755] usbcore: registered new interface driver ums-sddr09
[   25.673841] usbcore: registered new interface driver ums-sddr55
[   25.689276] usbcore: registered new interface driver ums-usbat
[   25.735016] xt_time: kernel timezone is -0000
[   25.747281] usbcore: registered new interface driver cdc_ether
[   25.778093] PPP generic driver version 2.4.2
[   25.790614] NET: Registered protocol family 24
[   25.803474] usbcore: registered new interface driver rndis_host
[   25.843997] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[   25.858546] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[   25.874013] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[   26.009918] kmodloader: done loading kernel modules from /etc/modules.d/*
[   27.841348] random: jshn: uninitialized urandom read (4 bytes read, 53 bits of entropy available)
[   27.931662] random: jshn: uninitialized urandom read (4 bytes read, 53 bits of entropy available)
[   36.161372] 8021q: adding VLAN 0 to HW filter on device eth0
[   36.196415] device eth0.2 entered promiscuous mode
[   36.206101] device eth0 entered promiscuous mode
[   36.357807] br-lan: port 1(eth0.2) entered forwarding state
[   36.369090] br-lan: port 1(eth0.2) entered forwarding state
[   38.448948] br-lan: port 1(eth0.2) entered forwarding state
[   49.889366] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   49.954397] jffs2_build_filesystem(): unlocking the mtd device... done.
[   49.967647] jffs2_build_filesystem(): erasing all blocks after the end marker...
[   50.037219] jffs2: Newly-erased block contained word 0x20031985 at offset 0x00b3d000
[   50.297213] jffs2: Newly-erased block contained word 0x20031985 at offset 0x00b3c000
[   50.537160] jffs2: Newly-erased block contained word 0x20031985 at offset 0x00b3a000
[   50.457233] jffs2: Newly-erased block contained word 0x20031985 at offset 0x00b3b000

<and so on...>

[  174.409539] jffs2: Newly-erased block contained word 0x20031985 at offset 0x00001000
[  174.449183] jffs2: Newly-erased block contained word 0xdec0adde at offset 0x00000000
[  174.464860] done.
[  174.468753] jffs2: notice: (1108) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.



BusyBox v1.25.1 () built-in shell (ash)

     _________
    /        /\      _    ___ ___  ___
   /  LE    /  \    | |  | __|   \| __|
  /    DE  /    \   | |__| _|| |) | _|
 /________/  LE  \  |____|___|___/|___|                      lede-project.org
 \        \   DE /
  \    LE  \    /  -----------------------------------------------------------
   \  DE    \  /    Reboot (17.01.4, r3560-79f57e422d)
    \________\/    -----------------------------------------------------------

=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@LEDE:/#

I meet same "jffs2: Newly-erased block contained word 0xdec0adde at offset x" problem in release version 17.01.4. I have to flash back old version firmware (15.05.1) .

nmtr wrote:

I meet same "jffs2: Newly-erased block contained word 0xdec0adde at offset x" problem in release version 17.01.4. I have to flash back old version firmware (15.05.1) .

I've written up a bug report, if it is of any help: https://bugs.lede-project.org/index.php … sk_id=1344

(Last edited by mihneapop on 21 Feb 2018, 20:50)

The discussion might have continued from here.