OpenWrt Forum Archive

Topic: Linksys E1200 v2

The content of this topic has been archived on 1 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

Hello,

I'm trying to configure OpenWRT trunk on a Linksys E1200 v2 but I haven't been able to setup Wifi. I've tried with all drivers, but everytime I type wifi detect there's no output, except when I'm using the kmod-brcm-wl driver, in which case the output is the following:

ls: /sys/class/ieee80211: No such file or directory

Here's the boot log when using the kmod-brcm-wl driver:

[    0.000000] Linux version 3.10.26 (openwrt@OpenWRT) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r39287) ) #1 Tue Jan 14 20:05:30 MST 2014
[    0.000000] CPU revision is: 00019749 (MIPS 74Kc)
[    0.000000] bcm47xx: using bcma bus
[    0.000000] bcma: bus0: Found chip with id 0xD144, rev 0x01 and package 0x08
[    0.000000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x27, class 0x0)
[    0.000000] bcma: bus0: Core 3 found: MIPS 74K (manuf 0x4A7, id 0x82C, rev 0x05, class 0x0)
[    0.000000] bcma: bus0: Found rev 9 PMU (capabilities 0x28982A09)
[    0.000000] bcma: bus0: Found serial flash
[    0.000000] bcma: bus0: Found M25P64 serial flash (size: 8192KiB, blocksize: 0x10000, blocks: 128)
[    0.000000] bcma: bus0: Early bus registered
[    0.000000] MIPS: machine is Linksys E1200 V2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 802dcbe0, node_mem_map 81000000
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8192 pages, LIFO batch:0
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 28972k/32768k available (2415k kernel code, 3796k reserved, 593k data, 184k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Setting up vectored interrupts
[    0.060000] Calibrating delay loop... 148.88 BogoMIPS (lpj=744448)
[    0.060000] pid_max: default: 32768 minimum: 301
[    0.070000] Mount-cache hash table entries: 512
[    0.070000] NET: Registered protocol family 16
[    0.090000] bio: create slab <bio-0> at 0
[    0.100000] Switching to clocksource MIPS
[    0.110000] NET: Registered protocol family 2
[    0.110000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.110000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.110000] TCP: Hash tables configured (established 512 bind 512)
[    0.110000] TCP: reno registered
[    0.110000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.110000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.110000] NET: Registered protocol family 1
[    0.110000] PCI: CLS 0 bytes, default 32
[    0.110000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x1C, class 0x0)
[    0.110000] bcma: bus0: Core 2 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x03, class 0x0)
[    0.110000] bcma: bus0: Core 4 found: SDR/DDR1 Memory Controller (manuf 0x4BF, id 0x835, rev 0x02, class 0x0)
[    0.190000] can not parse nvram name sb/1/rxpo2g(null) with value 0xff got -34
[    0.470000] bcma: bus0: Using SPROM revision 8 provided by platform.
[    0.470000] bcma: bus0: PMU resource config unknown or not needed for device 0xD144
[    0.470000] bcma: bus0: Workarounds unknown or not needed for device 0xD144
[    0.470000] bcma: bus0: Initializing MIPS core...
[    0.470000] bcma: bus0: set_irq: core 0x0812, irq 3 => 3
[    0.470000] bcma: bus0: set_irq: core 0x082d, irq 4 => 4
[    0.470000] bcma: bus0: set_irq: core 0x0800, irq 2 => 2
[    0.470000] bcma: bus0: IRQ reconfiguration done
[    0.470000] bcma: core 0x0800, irq : 2(S)* 3  4  5  6  D  I
[    0.470000] bcma: core 0x082c, irq : 2(S)  3  4  5  6  D  I*
[    0.470000] bcma: core 0x0812, irq : 2(S)  3* 4  5  6  D  I
[    0.470000] bcma: core 0x082d, irq : 2(S)  3  4* 5  6  D  I
[    0.470000] bcma: core 0x0835, irq : 2(S)  3  4  5  6  D* I
[    0.470000] bcma: bus0: Bus registered
[    0.480000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.480000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.480000] msgmni has been set to 56
[    0.480000] io scheduler noop registered
[    0.480000] io scheduler deadline registered (default)
[    0.480000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.510000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2) is a U6_16550A
[    0.840000] console [ttyS0] enabled
[    0.900000] 6 bcm47xxpart partitions found on MTD device bcm47xxsflash
[    0.900000] Creating 6 MTD partitions on "bcm47xxsflash":
[    0.910000] 0x000000000000-0x000000040000 : "boot"
[    0.920000] 0x000000040000-0x0000007f0000 : "firmware"
[    0.930000] 0x00000004001c-0x000000040960 : "loader"
[    0.930000] 0x000000040960-0x000000149c00 : "linux"
[    0.940000] mtd: partition "linux" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.960000] 0x000000149c00-0x0000007f0000 : "rootfs"
[    0.960000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.980000] mtd: device 4 (rootfs) set to be root filesystem
[    0.980000] mtd: partition "rootfs_data" created automatically, ofs=0x320000, len=0x4d0000
[    0.990000] 0x000000320000-0x0000007f0000 : "rootfs_data"
[    1.000000] 0x0000007f0000-0x000000800000 : "nvram"
[    1.020000] libphy: Fixed MDIO Bus: probed
[    1.020000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds)
[    1.030000] GPIO_WDT: failed to register misc device
[    1.040000] TCP: cubic registered
[    1.040000] NET: Registered protocol family 17
[    1.050000] Bridge firewalling registered
[    1.050000] can: controller area network core (rev 20120528 abi 9)
[    1.060000] NET: Registered protocol family 29
[    1.060000] 8021q: 802.1Q VLAN Support v1.8
[    1.080000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.090000] Freeing unused kernel memory: 184K (802f2000 - 80320000)
[    5.540000] pps_core: LinuxPPS API ver. 1 registered
[    5.550000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    5.560000] PTP clock support registered
[    5.580000] bgmac bcma0:1: Found PHY addr: 30 (NOREGS)
[    5.590000] bgmac bcma0:1: Support for Roboswitch not implemented
[    5.600000] libphy: bgmac mii bus: probed
[    5.620000] b53_common: found switch: BCM5325, rev 4
[    5.630000] bgmac: Broadcom 47xx GBit MAC driver loaded
[   10.950000] jffs2: notice: (240) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 38 of xref (0 dead, 2 orphan) found.
[   14.560000] NET: Registered protocol family 10
[   15.600000] wl: module license 'unspecified' taints kernel.
[   15.600000] Disabling lock debugging due to kernel taint
[   15.740000] wl0: 5.10.56.27 driver failed with code 13
[   15.750000] The attach callback failed, BCMA probe aborted
[   15.750000] SSB/BCMA glue driver successfully attached
[   15.780000] nf_conntrack version 0.5.0 (455 buckets, 1820 max)
[   15.800000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   15.840000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.920000] xt_time: kernel timezone is -0000
[   15.940000] PPP generic driver version 2.4.2
[   15.950000] NET: Registered protocol family 24
[   25.920000] device eth0.1 entered promiscuous mode
[   25.920000] device eth0 entered promiscuous mode
[   25.930000] br-lan: port 1(eth0.1) entered forwarding state
[   25.940000] br-lan: port 1(eth0.1) entered forwarding state
[   26.900000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[   27.940000] br-lan: port 1(eth0.1) entered forwarding state

I noticed the following: [   15.740000] wl0: 5.10.56.27 driver failed with code 13.

Is this device supported? As I said, I've tried with every wireless driver and haven't been able to do anything.

Thanks for your help.

(Last edited by kashano on 17 Jan 2014, 03:38)

kashano,
  Could you resolve the issue?Pls share.

I build Barrier Breaker package for LinkSys E4200(Broadcom BCM4718 Target board with BCM4331 Wireless NIC).

root@OpenWrt:~# wl ver
wl: wl driver adapter not found
root@OpenWrt:~#

in dmesg--->
[   15.630000] wl: module license 'unspecified' taints kernel.
[   15.630000] Disabling lock debugging due to kernel taint
[   15.740000] wl0: Broadcom BCM4329 802.11 Wireless Controller 5.10.56.27

[   15.790000] wl1: 5.10.56.27 driver failed with code 11
[   15.800000] Memory leak of bytes 20

Can you pls help?

Regards
muktikanta

I've got an E1200v2 running Chaos Calmer 15.05 r46767.

dmesg output:

[    0.000000] Linux version 3.18.20 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46450) ) #1 Fri Sep 4 15:10:42 CEST 2015
[    0.000000] CPU0 revision is: 00019749 (MIPS 74Kc)
[    0.000000] bcm47xx: Using bcma bus
[    0.000000] bcma: bus0: Found chip with id 53572, rev 0x01 and package 0x08
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff]
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 802ee300, node_mem_map 81000000
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8192 pages, LIFO batch:0
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 28840K/32768K available (2637K kernel code, 113K rwdata, 328K rodata, 172K init, 288K bss, 3928K reserved, 0K highmem)
[    0.000000] NR_IRQS:128
[    0.000000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x27, class 0x0)
[    0.000000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x1C, class 0x0)
[    0.000000] bcma: bus0: Core 2 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x03, class 0x0)
[    0.000000] bcma: bus0: Core 3 found: MIPS 74K (manuf 0x4A7, id 0x82C, rev 0x05, class 0x0)
[    0.000000] bcma: bus0: Core 4 found: SDR/DDR1 Memory Controller (manuf 0x4BF, id 0x835, rev 0x02, class 0x0)
[    0.000000] bcma: bus0: Found rev 9 PMU (capabilities 0x28982A09)
[    0.000000] bcma: bus0: Found serial flash
[    0.000000] bcma: bus0: Found M25P64 serial flash (size: 8192KiB, blocksize: 0x10000, blocks: 128)
[    0.000000] bcma: bus0: Early bus registered
[    0.000000] MIPS: machine is Linksys E1200 V2
[    0.000000] bcm47xx: Setting up vectored interrupts
[    0.070000] Calibrating delay loop... 149.91 BogoMIPS (lpj=749568)
[    0.070000] pid_max: default: 32768 minimum: 301
[    0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.070000] NET: Registered protocol family 16
[    0.100000] Switched to clocksource MIPS
[    0.100000] NET: Registered protocol family 2
[    0.100000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.100000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.100000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.100000] TCP: reno registered
[    0.100000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.100000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.110000] NET: Registered protocol family 1
[    0.110000] PCI: CLS 0 bytes, default 32
[    0.130000] can not parse nvram name sb/1/rxpo2g(null) with value 0xff got -34
[    0.140000] bcma: bus0: Using SPROM revision 8 provided by platform.
[    0.140000] bcma: bus0: PMU resource config unknown or not needed for device 0xD144
[    0.150000] bcma: bus0: Workarounds unknown or not needed for device 0xD144
[    0.150000] bcma: bus0: Initializing MIPS core...
[    0.150000] bcma: bus0: set_irq: core 0x0812, irq 3 => 3
[    0.150000] bcma: bus0: set_irq: core 0x082d, irq 4 => 4
[    0.150000] bcma: bus0: set_irq: core 0x0800, irq 2 => 2
[    0.150000] bcma: bus0: IRQ reconfiguration done
[    0.150000] bcma: core 0x0800, irq : 2(S)* 3  4  5  6  D  I 
[    0.150000] bcma: core 0x0812, irq : 2(S)  3* 4  5  6  D  I 
[    0.150000] bcma: core 0x082d, irq : 2(S)  3  4* 5  6  D  I 
[    0.150000] bcma: core 0x082c, irq : 2(S)  3  4  5  6  D  I*
[    0.150000] bcma: core 0x0835, irq : 2(S)  3  4  5  6  D* I 
[    0.150000] bcma: bus0: Bus registered
[    0.150000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.150000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.150000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.150000] msgmni has been set to 56
[    0.150000] io scheduler noop registered
[    0.150000] io scheduler deadline registered (default)
[    0.150000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.160000] console [ttyS0] disabled
[    0.180000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2, base_baud = 1250000) is a U6_16550A
[    0.540000] console [ttyS0] enabled
[    0.590000] 6 bcm47xxpart partitions found on MTD device bcm47xxsflash
[    0.590000] Creating 6 MTD partitions on "bcm47xxsflash":
[    0.600000] 0x000000000000-0x000000040000 : "boot"
[    0.610000] 0x000000040000-0x0000007f0000 : "firmware"
[    0.610000] 0x00000004001c-0x00000004090c : "loader"
[    0.620000] 0x00000004090c-0x00000014b400 : "linux"
[    0.630000] 0x00000014b400-0x0000007f0000 : "rootfs"
[    0.640000] mtd: device 4 (rootfs) set to be root filesystem
[    0.640000] 1 squashfs-split partitions found on MTD device rootfs
[    0.650000] 0x000000370000-0x0000007f0000 : "rootfs_data"
[    0.660000] 0x0000007f0000-0x000000800000 : "nvram"
[    0.660000] bgmac bcma0:2: Found PHY addr: 30 (NOREGS)
[    0.670000] bgmac bcma0:2: Support for Roboswitch not implemented
[    0.720000] libphy: bgmac mii bus: probed
[    0.800000] b53_common: found switch: BCM5325, rev 4
[    0.810000] bgmac: Broadcom 47xx GBit MAC driver loaded
[    0.820000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds)
[    0.830000] TCP: cubic registered
[    0.830000] NET: Registered protocol family 17
[    0.830000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.850000] Bridge firewalling registered
[    0.850000] 8021q: 802.1Q VLAN Support v1.8
[    0.870000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    0.880000] Freeing unused kernel memory: 172K (80305000 - 80330000)
[    2.700000] init: Console is alive
[    2.710000] init: - watchdog -
[    4.730000] init: - preinit -
[    5.660000] random: mktemp urandom read with 8 bits of entropy available
[    9.280000] jffs2: notice: (222) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    9.300000] mount_root: switching to jffs2 overlay
[    9.360000] procd: - early -
[    9.360000] procd: - watchdog -
[   10.490000] procd: - ubus -
[   11.500000] procd: - init -
[   14.130000] NET: Registered protocol family 10
[   14.140000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   14.170000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[   14.180000] Backport generated by backports.git backports-20150129-0-gdd4a670
[   14.200000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.220000] nf_conntrack version 0.5.0 (453 buckets, 1812 max)
[   14.300000] xt_time: kernel timezone is -0000
[   14.350000] cfg80211: Calling CRDA to update world regulatory domain
[   14.390000] cfg80211: World regulatory domain updated:
[   14.390000] cfg80211:  DFS Master region: unset
[   14.400000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   14.410000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   14.420000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   14.420000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   14.430000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   14.440000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   14.450000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   14.460000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   14.470000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   14.570000] PPP generic driver version 2.4.2
[   14.580000] NET: Registered protocol family 24
[   14.630000] b43-phy0: Broadcom 53572 WLAN found (core revision 28)
[   14.650000] b43-phy0: Found PHY: Analog 9, Type 4 (N), Revision 17
[   14.650000] b43-phy0 ERROR: FOUND UNSUPPORTED RADIO (Manuf 0x17F, ID 0x2057, Revision 13, Version 0)
[   14.660000] b43: probe of bcma0:1 failed with error -122
[   14.670000] Broadcom 43xx driver loaded [ Features: NL ]
[   30.180000] device eth0.1 entered promiscuous mode
[   30.190000] device eth0 entered promiscuous mode
[   30.200000] br-lan: port 1(eth0.1) entered forwarding state
[   30.200000] br-lan: port 1(eth0.1) entered forwarding state
[   32.200000] br-lan: port 1(eth0.1) entered forwarding state
[   80.810000] random: nonblocking pool is initialized

Toward the end you can see the "ERROR: FOUND UNSUPPORTED RADIO," which seems to be new since your post, kashano.

I tried the kmod-brcm-wl, and got mostly the same results: wifi detect says nothing, /sys/class/ieee80211 is empty (but it exists), and the same messages:

[ 9736.420000] wl: module license 'unspecified' taints kernel.
[ 9736.430000] Disabling lock debugging due to kernel taint
[ 9736.540000] wl0: 5.10.56.27 driver failed with code 13
[ 9736.540000] The attach callback failed, BCMA probe aborted
[ 9736.550000] SSB/BCMA glue driver successfully attached

This is with the 15.05 build marked e1200-v2.

Note - the ticket for BCM5357 wireless drivers was closed in June 2014 as "wontfix." But perhaps some of the "huge work needed to get this working" may have been done in the time between then and now; I'm not sure of its exact nature.

(Last edited by jaredjennings on 17 Nov 2015, 05:55)

The discussion might have continued from here.