Here is some details from it. I have not been able to interrupt the boot process and get into uboot.
The serial cable works to break into the shell after the linux userland is up and running but nothing works to stop autoboot.
It says "Hit any key to stop autoboot" but it doesn't seem to be the case.
/proc # lsmod
Module Size Used by
ip6t_REJECT 4176 0 - Live 0x863aa000
ip6table_filter 2256 1 - Live 0x87bd5000
ip6_tables 12448 1 ip6table_filter, Live 0x8639c000
usb_storage 55408 0 - Live 0x86360000
ath_pktlog 18000 0 - Live 0x86248000 (P)
umac 1633312 1 ath_pktlog, Live 0x86000000
ath_dev 248592 2 ath_pktlog,umac, Live 0x868c0000 (P)
ath_dfs 59792 1 umac, Live 0x86ab0000 (P)
ath_spectral 34864 2 umac,ath_dev, Live 0x86ae0000 (P)
ath_rate_atheros 39936 3 ath_pktlog,umac,ath_dev, Live 0x86920000 (P)
ath_hal 675024 4 ath_pktlog,umac,ath_dev,ath_rate_atheros, Live 0x86a00000 (P)
asf 10496 5 umac,ath_dev,ath_dfs,ath_spectral,ath_hal, Live 0x868b4000 (P)
adf 19168 3 umac,ath_dev,ath_hal, Live 0x868a0000 (P)
jcp_cmd 5584 0 - Live 0x86832000
jcp 6256 1 jcp_cmd, Live 0x86830000
sxuptp_driver 2960 0 - Live 0x87bdc000
sxuptp_devfilter 2960 0 - Live 0x86825000
sxuptp_idfilter 1136 0 - Live 0x8682d000 (P)
sxuptp 33152 5 jcp_cmd,jcp,sxuptp_driver,sxuptp_devfilter,sxuptp_idfilter, Live 0x86840000
ehci_hcd 40784 0 - Live 0x86800000
ar934x_gpio 5872 0 - Live 0x87b54000
athrs_gmac 292736 0 - Live 0x87b00000
devnvram 14080 26 - Live 0x87a34000
/proc #
Please stand by while rebooting the system.
Restarting system.
▒
U-Boot 1.1.4-g08bc1b20 (Feb 6 2014 - 10:13:09)
ap136 - Scorpion 1.0DRAM:
sri
Scorpion 1.0
ath_ddr_initial_config(183): (32bit) ddr2 init
tap = 0x00000003
Tap (low, high) = (0x6, 0x1c)
Tap values = (0x11, 0x11, 0x11, 0x11)
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 217k for U-Boot at: 87fc8000
Reserving 192k for malloc() at: 87f98000
Reserving 44 Bytes for Board Info at: 87f97fd4
Reserving 36 Bytes for Global Data at: 87f97fb0
Reserving 128k for boot params() at: 87f77fb0
Stack Pointer at: 87f77f98
Now running in RAM - U-Boot at: 87fc8000
flash size 16MB, sector count = 256
Flash: 32 MB, Dual NOR Flash support.
*** Warning - bad CRC, using default environment
*** Warning *** : PCIe WLAN Module not found !!!
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
athrs_sgmii_res_cal: cal value = 0x1
default_mac_from_artblock: C0:A0:BB:F0:05:BB from 0xBFFE0004
No valid address in Flash. Using fixed address
default_mac_from_artblock: C0:A0:BB:F0:05:BB from 0xBFFE0004
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ----> S17 PHY *
Vlan config...
s17 phy0 register value 0x00004140
TEST: FINAL REG VAL after TX Calibration - 0x46000000
TEST: FINAL XMII VAL after RX Calibration - 0x56000000
TEST: FINAL ETH_CFG VAL after RX Calibration - 0x00028001
not is_drqfn
new change S17_P0PAD_MODE_REG 4= [0x80] athrs17_reg_init: complete
: cfg1 0x80000000 cfg2 0x7335
eth0: 00:03:7f:09:0b:ad
eth0 up
athrs17_reg_init_wan done
athrs17_reg_init_wan S17_P6PAD_MODE_REG c= [0x7600000] done
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x800c0000 cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
eth1 up
eth0, eth1
Setting 0x18116290 to 0x4488214f
main_loop 442> gpio 17 value 1 , bootdelay:2
Hit any key to stop autoboot 0: 0
Update kernel boot addr to 0x9f040000
Booting from 1st flash
## Booting image at 9f040000 ...
Image Name: Linux Kernel Image
Created: 2014-02-05 9:17:06 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1445154 Bytes = 1.4 MB
Load Address: 80002000
Entry Point: 80317d70
Verifying Checksum at 0x9f040040 ...OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80317d70) ...
## bootargs 0: console=ttyS0,115200 root=31:02 rootfstype=jffs2 init=/sbin/init mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),6336k(rootfs),1408k(uImage),8256k(mib0),64k(ART)...
## Single flash image
## bootargs @A7F77FB0: console=ttyS0,115200 mem=128M root=31:03 rootfstype=squashfs,jffs2 init=/sbin/init loader= build="Feb 6 2014" mtdparts=ath-nor0:192k(u-boot),64k(nvram),15296k(linux),13824k@0x001b0000(rootfs),192k(LANG),512k(My-Dlink),64k(MAC),64k(ART)...
## Giving linux memsize in bytes, 134217728
Starting kernel ...
Booting QCA955x
Linux version 2.6.31 (vicchang@vicchang-desktop) (gcc version 4.3.3 (GCC) ) #1 Wed Feb 5 17:01:47 CST 2014
flash_size passed from bootloader = 16
arg 1: console=ttyS0,115200
arg 2: mem=128M
arg 3: root=31:03
arg 4: rootfstype=squashfs,jffs2
arg 5: init=/sbin/init
arg 6: loader=
arg 7: build="Feb 6 2014"
arg 8: mtdparts=ath-nor0:192k(u-boot),64k(nvram),15296k(linux),13824k@0x001b0000(rootfs),192k(LANG),512k(My-Dlink),64k(MAC),64k(ART)
CPU revision is: 00019750 (MIPS 74Kc)
cpu apb ddr apb ath_sys_frequency: cpu 720 ddr 600 ahb 200
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 08000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00008000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00008000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: console=ttyS0,115200 mem=128M root=31:03 rootfstype=squashfs,jffs2 init=/sbin/init loader= build="Feb 6 2014" mtdparts=ath-nor0:192k(u-boot),64k(nvram),15296k(linux),13824k@0x001b0000(rootfs),192k(LANG),512k(My-Dlink),64k(MAC),64k(ART)
PID hash table entries: 512 (order: 9, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 111132k/131072k available (3188k kernel code, 19776k reserved, 796k data, 168k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 359.42 BogoMIPS (lpj=718848)
Mount-cache hash table entries: 512
****************ALLOC***********************
Packet mem: 804261a0 (0xe00000 bytes)
********************************************
NET: Registered protocol family 16
ath_pcibios_init: bus 0
ath_pcibios_init(238): PCI 0 CMD write: 0x356
registering PCI controller with io_map_base unset
ath_pcibios_init: bus 1
***** Warning PCIe 1 H/W not found !!!
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:00.0: PME# disabled
pcibios_map_irq: IRQ 75 for bus 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
fuse init (API version 7.12)
msgmni has been set to 217
alg: No test for lzma (lzma-generic)
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
brd: module loaded
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
PPPoL2TP kernel driver, V1.0
HDLC support module revision 1.22
8 cmdlinepart partitions found on MTD device ath-nor0
Creating 8 MTD partitions on "ath-nor0":
0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "nvram"
0x000000040000-0x000000f30000 : "linux"
0x0000001b0000-0x000000f30000 : "rootfs"
0x000000f30000-0x000000f60000 : "LANG"
0x000000f60000-0x000000fe0000 : "My-Dlink"
0x000000fe0000-0x000000ff0000 : "MAC"
0x000000ff0000-0x000001000000 : "ART"
u32 classifier
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
nf_conntrack_rtsp v0.6.21 loading
xt_time: kernel timezone is -0000
nf_nat_rtsp v0.6.21 loading
ip_tables: (C) 2000-2006 Netfilter Core Team
/proc/router_ip created
TCP cubic registered
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
arch/mips/atheros/gpio.c (ath_simple_config_init) JUMPSTART_GPIO: 16
athwdt_init: Registering WDT success
20000000, 1312D00, USEC_PER_SEC: 1000000,ath_ahb_freq: 200000000
ath_otp_init: Registering OTP success
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
Freeing unused kernel memory: 168k freed
init started: BusyBox v1.01 (2014.02.05-09:16+0000) multi-call binary
init NVRAM_SPACE from mtdblock size
init nvram memory map size: 0x10000 order of pages: 0x4
nvram module init:
/dev/nvram major number 225 glues to mtd: "nvram" size: 0x00010000
nvram_space: 0x00010000 mapped via mmap(2)
openfile :nvram_commit: size crc 10000 erasesize:10000, nvram->size: 8031C68C
/etc/sysinfo
new ver: 1.0
old ver: 1.0
new ver: 1.0
old ver: 1.0
openfile :/etc/sysinfo
[nvram_commit] by [cli] (196), parent process [rcS] (187)
init artblock :lan_mac=C0:A0:BB:F0:05:BB to "sys_lan_mac"
init artblock :wan_mac=C0:A0:BB:F0:05:BC to "sys_wan_mac"
init artblock :hw_version=A1 to "sys_hw_version"
init artblock :wlan0_domain=0x14 to "sys_wlan0_domain"
begin /etc/sysconfig/S2eth_init.sh
Inserting switch driver - HNAT enable ...
qca955x_GMAC: Length per segment 1536
955x_GMAC: qca955x_gmac_attach
955x_GMAC: qca955x_set_gmac_caps
Currently in polling mode unit0
mac:0 Registering S17....
qca955x_GMAC: RX TASKLET - Pkts per Intr:160
qca955x_GMAC: Mac address for unit 0:bfff0000
qca955x_GMAC: ff:ff:ff:ff:ff:ff
qca955x_GMAC: Max segments per packet : 1
qca955x_GMAC: Max tx descriptor count : 128
qca955x_GMAC: Max rx descriptor count : 224
qca955x_GMAC: Mac capability flags : 10002A00
955x_GMAC: qca955x_gmac_attach
955x_GMAC: qca955x_set_gmac_caps
Currently in polling mode unit1
mac:1 Registering S17....
qca955x_GMAC: RX TASKLET - Pkts per Intr:160
qca955x_GMAC: Mac address for unit 1:bfff0006
qca955x_GMAC: ff:ff:ff:ff:ff:ff
qca955x_GMAC: Max segments per packet : 1
qca955x_GMAC: Max tx descriptor count : 128
qca955x_GMAC: Max rx descriptor count : 224
qca955x_GMAC: Mac capability flags : 12002200
955x_GMAC: Serdes PLL is locked value 0x18838116
To set s17 LOOKUP_CTRL_REG registers, flag 0
athr_gmac_ring_alloc Allocated 2048 at 0x87ac2000
sram_desc_cnt 1536,mac Unit 0,Tx r->ring_desc 0xbd000000
athr_gmac_ring_alloc Allocated 3584 at 0x87a16000
sram_desc_cnt 4224,mac Unit 0,Rx r->ring_desc 0xbd000600
955x_GMAC: eth0 in RGMII MODE
Scorpion -----> S17 PHY
Setting up VLAN Configuration ..done
/proc/qca_switch/nf_athrs17_hnat is created
/proc/qca_switch/nf_athrs17_hnat_wan_type is created
/proc/qca_switch/nf_athrs17_hnat_ppp_id is created
/proc/qca_switch/nf_athrs17_hnat_udp_thresh is created
/proc/qca_switch/nf_athrs17_hnat_wan_ip is created
/proc/qca_switch/nf_athrs17_hnat_ppp_peer_ip is created
/proc/qca_switch/nf_athrs17_hnat_ppp_peer_mac is created
/proc/qca_switch/nf_athrs17_hnat_wan_mac is created
Hello, nat helper module for 1.1!
######## S17 SSDK init succeeded! ########
Creating proc entries for athrs17 done
athrs17_reg_init:done
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
To set s17 LOOKUP_CTRL_REG registers, flag 1
ADDRCONF(NETDEV_UP): eth0: link is not ready
To set s17 LOOKUP_CTRL_REG registers, flag 0
athr_gmac_ring_alloc Allocated 2048 at 0x87a48800
sram_desc_cnt 5760,mac Unit 1,Tx r->ring_desc 0xbd001080
athr_gmac_ring_alloc Allocated 3584 at 0x87a7a000
sram_desc_cnt 8448,mac Unit 1,Rx r->ring_desc 0xbd001680
955x_GMAC: eth1 in SGMII MODE
Scorpion -----> S17 PHY
athrs17_reg_init_wan done
955x_SGMII::athr_gmac_sgmii_setup Done
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
Phy setup Complete
athrs17_phy_setup Disable MAC Port 6
## isis_set_pppoe_passthrough enabled !
## isis_enable_pppoe_discovery_acl !
athrs17_reg_write(MOD_ENABLE_OFFSET) = 0x80000007
Adding ACL rules 7 - ipv6_snooping_solicted_node_add_acl_rules
Adding ACL rules 9 - ipv6_snooping_sextuple0_group_add_acl_rules
Adding ACL rules 10 - ipv6_snooping_quintruple0_1_group_add_acl_rules
Adding ACL rules 8 - ipv6_snooping_nodeinfo_query_add_acl_rules
955x_GMAC: enet unit:1 is up...
eth1 SGMII 1000Mbps full duplex
955x_GMAC: qca955x_soc_gmac_set_mac_duplex
955x_GMAC: qca955x_soc_gmac_set_link Done
955x_GMAC: done cfg2 0x7215 ifctl 0x0 miictrl
To set s17 LOOKUP_CTRL_REG registers, flag 1
device eth1 entered promiscuous mode
device eth1.1 entered promiscuous mode
br0: port 1(eth1.1) entering forwarding state
device eth1.1 is already a member of a bridge; can't enslave it to bridge br0.
end /etc/sysconfig/S2eth_init.sh
AR934x GPIO Controller
init gpio 14
init gpio 22
init gpio 23
init gpio 19
begin /etc/sysconfig/S2vlan.sh
end /etc/sysconfig/S2vlan.sh
begin S3_s17_acl_ssdp.sh
Write Reg: 0x00000404: Oldval = 0xff000000 Newval = 0x5e7ffffa
Write Reg: 0x00000408: Oldval = 0x00000002 Newval = 0x00000100
Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x00000410: Oldval = 0xff020000 Newval = 0x08000001
Write Reg: 0x00000414: Oldval = 0x0000000f Newval = 0x0000001f
Write Reg: 0x00000400: Oldval = 0x00000007 Newval = 0x8000000b
Write Reg: 0x00000404: Oldval = 0xff000000 Newval = 0xffffffff
Write Reg: 0x00000408: Oldval = 0x00000002 Newval = 0x0000ffff
Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x00000410: Oldval = 0xff020000 Newval = 0xffff0fff
Write Reg: 0x00000414: Oldval = 0x0000000f Newval = 0x000000c9
Write Reg: 0x00000400: Oldval = 0x0000000b Newval = 0x8000010b
Write Reg: 0x00000404: Oldval = 0xff000000 Newval = 0x00000000
Write Reg: 0x00000408: Oldval = 0x00000002 Newval = 0xe0000000
Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x00000013
Write Reg: 0x00000410: Oldval = 0xff020000 Newval = 0x00000000
Write Reg: 0x00000414: Oldval = 0x0000000f Newval = 0x00000000
Write Reg: 0x00000400: Oldval = 0x0000010b Newval = 0x8000020b
Write Reg: 0x00000404: Oldval = 0xff000000 Newval = 0x00000000
955x_GMAC: enet unit:0 is up...
eth0 RGMII 1000Mbps full duplex
955x_GMAC: qca955x_soc_gmac_set_mac_duplex
955x_GMAC: qca955x_soc_gmac_set_link Done
955x_GMAC: done cfg2 0x7215 ifctl 0x0 miictrl
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Write Reg: 0x00000408: Oldval = 0x00000002 Newval = 0xc0a83701
Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x00000410: Oldval = 0xff020000 Newval = 0x00000000
Write Reg: 0x00000414: Oldval = 0x0000000f Newval = 0x0000009e
Write Reg: 0x00000400: Oldval = 0x0000020b Newval = 0x80000056
Write Reg: 0x00000404: Oldval = 0xff000000 Newval = 0x00000000
Write Reg: 0x00000408: Oldval = 0x00000002 Newval = 0xffffff00
Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x00000410: Oldval = 0xff020000 Newval = 0x00030000
Write Reg: 0x00000414: Oldval = 0x0000000f Newval = 0x800000c2
Write Reg: 0x00000400: Oldval = 0x00000056 Newval = 0x80000156
Write Reg: 0x00000404: Oldval = 0xff000000 Newval = 0x00000000
Write Reg: 0x00000408: Oldval = 0x00000002 Newval = 0x00000000
Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x000000d0
Write Reg: 0x00000410: Oldval = 0xff020000 Newval = 0x00000000
Write Reg: 0x00000414: Oldval = 0x0000000f Newval = 0x00000000
Write Reg: 0x00000400: Oldval = 0x00000156 Newval = 0x80000256
end S3_s17_acl_ssdp.sh
begin S3_s17_igmpsnooping.sh
S17, enable HW igmp snooping
Write Reg: 0x00000624: Oldval = 0x007f7f7f Newval = 0x3f3f213f
Write Reg: 0x00000618: Oldval = 0x50e8002b Newval = 0x50f8002b
Write Reg: 0x00000214: Oldval = 0x00000000 Newval = 0x01060606
Write Reg: 0x00000210: Oldval = 0x00000000 Newval = 0x06060600
end S3_s17_igmpsnooping.sh
begin S3_s17_jumbo_frame.sh
S17, setting jumbo frames 9000 bytes
Write Reg: 0x00000078: Oldval = 0x000005ee Newval = 0x0000232e
end S3_s17_jumbo_frame.sh
Please press Enter to activate this console. ADDRCONF(NETDEV_CHANGE): eth1.1: link becomes ready
ADDRCONF(NETDEV_CHANGE): eth1.2: link becomes ready
killall: mydlink-watch-dog.sh: no process killed
killall: signalc: no process killed
killall: tsa: no process killed
opt.local stop ok.
opt.local start ok.
insmod: cannot insert `/lib/devnvram.ko': File exists (-1): File exists
openfile :/var/etc/nvram.default
Wed Feb 5 17:07:00 UTC 2014
sh: modprobe: not found
sh: modprobe: not found
/tmp/password has been created
/tmp/storage_pwd has been created
2014-02-05 17:07:02: (network.c.239) warning: please use server.use-ipv6 only for hostnames, not without server.bind / empty address; your config will break if the kernel default for IPV6_V6ONLY changes
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Port Status 1c000004
ath-ehci ath-ehci.0: ATH EHCI
ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Port Status 1c000000
ath-ehci1 ath-ehci1.1: ATH EHCI
ath-ehci1 ath-ehci1.1: new USB bus registered, assigned bus number 2
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci1 ath-ehci1.1: irq 3, io mem 0x1b400000
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci1 ath-ehci1.1: USB 2.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initialize silex modules start
Initialize Hotplug
Starting sxuptpd
sxuptp_idfilter: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
initializing USB device filter
usbcore: registered new interface driver sxuptp_driver
sh: /etc/sysconfig/gpl_init_service.sh: not found
rm: cannot remove `/var/wizard_lang.js': No such file or directory
rc is BUSY now!
eth1.2: Cannot assign requested address
eth1.2: Cannot assign requested address
cat: /var/etc/resolv_ipv6.conf: No such file or directory
umount: cannot umount /tmp/lang_pack: No such file or directory
umount: cannot umount /tmp/lang_pack: No such file or directory
mount: mounting /dev/mtdblock4 on /tmp/lang_pack failed
procfile_write (/proc/router_ip) called [192.168.55.1]
set router ip for netfilter
dhcpd_enabled::::::
domain empty
DHCP server start.
device_lan_ip=192.168.55.1 , device_lan_subnet_mask=255.255.255.0
max_leases value (254) not sane, setting to 100 instead
Unable to open /var/misc/udhcpd.leases for reading
##################### wlan wlan wlan wlan wlan wlan wlan wlan #########################
##################### wlan0_enable#########################
##################### wlan1_enable#########################
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_spectral: Version 2.0.0
Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reserved
SPECTRAL module built on Feb 5 2014 17:04:21
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
sh: /etc/sysconfig/gpl_wan_state.sh: not found
ath_ahb: 10.1.436 (Atheros/multi-bss)
__ath_attach: Set global_scn[0]
Enterprise mode: 0x33fc0000
Restoring Cal data from Flash
**************** CL2350327, Build with adaptive chanmask enabled by default *************
SPECTRAL : get_capability not registered
HAL_CAP_PHYDIAG : Capable
SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 226)
SPECTRAL : get_capability not registered
HAL_CAP_RADAR : Capable
SPECTRAL : Need to fix the capablity check for SPECTRAL
(spectral_attach : 231)
SPECTRAL : get_capability not registered
HAL_CAP_SPECTRAL_SCAN : Capable
SPECTRAL : get_tsf64 not registered
spectral_init_netlink 52 NULL SKB
SPECTRAL : No ADVANCED SPECTRAL SUPPORT
SPECTRAL : module attached
Green-AP : Green-AP : Attached
ath_get_caps[5957] rx chainmask mismatch actual 7 sc_chainmak 0
ath_get_caps[5932] tx chainmask mismatch actual 7 sc_chainmak 0
ath_attach_dfs[11940] dfsdomain 1
SPECTRAL : module already attached
SC Callback Registration for wifi0
wifi0: Atheros ???: mem=0xb8100000, irq=2
ath_pci: 10.1.436 (Atheros/multi-bss)
ath_pci_probe
PCI device id is 003c :003c
ath_pci 0000:00:00.0: ath DEBUG: sc=0x8688ea00
ol_ath_pci_configure : num_desired MSI set to 0
Using PCI Legacy Interrupt
__ol_ath_attach: ath_attach TODO
ol_ath_attach() BMI inited.
ol_ath_attach() BMI Get Target Info.
ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016c
NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0
ol_ath_attach() configure Target .
ol_transfer_bin_file 1594: Download Board data len 2116
ol_ath_download_firmware: Using 0x1234 for the remainder of init
ol_transfer_bin_file 1586: Download OTP data len 6276
ol_transfer_bin_file 1632: Download Firmware data len 186796
ol_ath_attach() Download FW.
ol_ath_attach() HT Create .
ol_ath_attach() HIF Claim.
ol_ath_attach() BMI Done.
ol_ath_attach() WMI attached. wmi_handle 861a0000
+HWT
CE_recv_buf_enqueue 457 Populate last entry 512 for CE 5
CE_recv_buf_enqueue 466 CE 5 wi 511 dest_ptr 0x7d49c0 nbytes 0 recv_ctxt 0x86b6fc80
-HWT
HTC Service:0x0300 ep:1 TX flow control disabled
CE_pkt_dl_len_set CE 4 Pkt download length 42
TXRX: Created pdev 8688e400
wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event
num_rf_chain : 00000003
ht_cap_info: : 0000085b
vht_cap_info : 338001b2
vht_supp_mcs : 0000ffea
FIRMWARE:P 49 V 16 T 155
wmi_ready_event_rx: WMI UNIFIED READY event
ol_ath_connect_htc() WMI is ready
ol_ath_set_host_app_area TODO
target uses HTT version 2.1; host uses 2.1
ol_ath_attach() connect HTC.
ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
Skipping VHT80 channel 5825
ol_ath_phyerr_attach: called
OL Resmgr Init-ed
ol_if_spectral_setup
SPECTRAL : get_capability not registered
HAL_CAP_PHYDIAG : Capable
SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 226)
SPECTRAL : get_capability not registered
HAL_CAP_RADAR : Capable
SPECTRAL : Need to fix the capablity check for SPECTRAL
(spectral_attach : 231)
SPECTRAL : get_capability not registered
HAL_CAP_SPECTRAL_SCAN : Capable
SPECTRAL : get_tsf64 not registered
spectral_init_netlink 52 NULL SKB
Green-AP : Green-AP : Attached
Green-AP : Attached
ol_if_dfs_setup: called
ol_if_dfs_attach: called; ptr=86b99974, radar_info=86831be8
ol_ath_rtt_meas_report_attach: called
ol_ath_attach() UMAC attach .
ol_if_dfs_configure: called
ol_if_dfs_configure: FCC domain
ol_if_SPECTRAL : Legacy (Non-11AC)
SPECTRAL : (Legacy) 20MHz Channel Width (Channel = 2412)
Enabled spectral scan on channel 2412
Channel 1 average beacon RSSI 8 noisefloor -103 SS Chan Load 0 ieee80211_acs_find_best_11ng_centerchan chan: 1 beacon RSSI + weighted noisefloor: -198
Channel 6 average beacon RSSI 15 noisefloor -104 SS Chan Load 0 ieee80211_acs_find_best_11ng_centerchan chan: 6 beacon RSSI + weighted noisefloor: -193
Channel 6 average beacon RSSI 15 noisefloor -104 SS Chan Load 0 ieee80211_acs_find_best_11ng_centerchan chan: 6 beacon RSSI + weighted noisefloor: -193
Channel 11 average beacon RSSI 7 noisefloor -103 SS Chan Load 0 ieee80211_acs_find_best_11ng_centerchan chan: 11 beacon RSSI + weighted noisefloor: -199
ieee80211_acs_find_best_11ng_centerchan found best 11ng center chan: 11 rssi: -199
mlme_create_infra_bss : Overriding HT40 channel with HT20 channel
FWLOG: [35390] WAL_DBGID_RX_LOCAL_BUFS_LWM ( 0x3 )
FWLOG: [35411] WAL_DBGID_RX_LOCAL_BUFS_LWM ( 0x3 )
FWLOG: [35431] WAL_DBGID_RX_LOCAL_BUFS_LWM ( 0x3 )
FWLOG: [35452] WAL_DBGID_RX_LOCAL_BUFS_LWM ( 0x3 )
FWLOG: [35472] WAL_DBGID_RX_LOCAL_BUFS_LWM ( 0x3 )
FWLOG: [35541] WAL_DBGID_RX_LOCAL_BUFS_LWM ( 0x3 )
FWLOG: [35541] WAL_DBGID_RX_LOCAL_BUFS_LWM ( 0x3 )
FWLOG: [35541] WAL_DBGID_RX_LOCAL_BUFS_LWM ( 0x3 )
killall: miniupnpd: no process killed
Function ieee80211_acs_find_best_11na_centerchan best 5G channel is 149
OL vap_start +
OL vap_start -
ol_vdev_start_resp_ev
ol_ath_vap_join: join operation is only for STA/IBSS mode
ol_ath_wmm_update:
Setting vdev param = 3, value = 200
Setting vdev param = 2b, value = 33
Notification to UMAC VAP layer
FWLOG: [35591] WAL_DBGID_RX_LOCAL_BUFS_LWM ( 0x3 )
/tmp/password has been created
/tmp/storage_pwd has been created
macaddr c0a0bbf005bb
########## read_in_uuid:1458 macaddr: c0a0bbf005bb
rm: cannot remove `/var/tmp/uid_count*': No such file or directory
rm: cannot remove `/var/tmp/uid_info*': No such file or directory
NMBD launched on port 137.
NMBD: name:DLINKROUTER
NMBD: name_local:DLINKROUTER.LOCAL
NMBD: model_name:DIR-862L
Creating minidlna.conf
start minidlna
grep: /tmp/smb.dir.conf: No such file or directory
grep: /tmp/smb.dir.conf: No such file or directory
chmod: /mydlink/mydlink-watch-dog.sh: Read-only file system
chmod: /mydlink/opt.local: Read-only file system
chmod: /mydlink/signalc: Read-only file system
chmod: /mydlink/tsa: Read-only file system
chmod: /mydlink/version: Read-only file system
killall: tsa: no process killed
opt.local stop ok.
killall: tsa: no process killed
opt.local stop ok.
opt.local start ok.
2014-02-05 17:07:20: (network.c.239) warning: please use server.use-ipv6 only for hostnames, not without server.bind / empty address; your config will break if the kernel default for IPV6_V6ONLY changes
Starting HotPlug
Initialize USB Storage
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
Start JCPD 19541
0
feature zero
2
access mode 0
umount: cannot umount /tmp/lang_pack: Invalid argument
umount: cannot umount /tmp/lang_pack: No such file or directory
mount: mounting /dev/mtdblock4 on /tmp/lang_pack failed
wan_ipaddr == NULL, firewall don't start
killall: wakeOnLanProxy: no process killed
Configuration fi ieee80211_ioctl_siwmode: imr.ifm_active=131738, new mode=3, valid=1
le: /var/tmp/WSCwmi_unified_vdev_stop_send
_ath1.conf
STOPPED EVENT for vap 0
br0: port 3(ath1) entering disabled state
ol_ath_vap_set_param: VAP param unsupported param:32 value:0
DEVICE IS DOWN ifname=ath1
ath1: Could not DEVICE IS DOWN ifname=ath1
connect to kerneol_ath_vap_set_param: VAP param unsupported param:32 value:0
l driver
ol_ath_vap_set_param: VAP param unsupported param:32 value:0
Using interface ath1 with hwaddr c0:a0:bb:f0:05:bd and ssid 'Damage Incorporated 5'
ol_ath_vap_set_param: VAP param unsupported param:32 value:1
ol_ath_vap_set_param: VAP param unsupported param:74 value:1
Group Keyidx set=1
wmi_unified_vdev_install_key_send Setting Key for Macaddress:0xbd05f0bba0c0
Keyix=1 Keylen=32 Keyflags=1 Cipher=2
Keydata=0xff 0x28 0xd7 0x33 0x7a 0x28 0xdc 0x51 0x8f 0x4b 0x84 0x5c 0x7c 0x75 0x9c 0xb9 0x28 0x33 0x1e 0x2e 0x50 0x81 0x86 0x66 0x19 0x70 0x57 0x8e 0x94 0x44 0x75 0x4c
ol_ath_vap_set_param: VAP param unsupported param:74 value:0
TXRX: ol_txrx_peer_find_add_id: peer 8624d800 ID 161
TXRX: sec spec for peer 8624d800 (c0:a0:bb:f0:05:bd): mcast key of type 4
Setting vdev param = 1f, value = 1
OL vap_stop +
wmi_unified_vdev_stop_send
OL vap_stop -
STOPPED EVENT for vap 0
OL vap_start +
OL vap_start -
ol_vdev_start_resp_ev
ol_ath_vap_join: join operation is only for STA/IBSS mode
ol_ath_wmm_update:
Setting vdev param = 3, value = 200
Setting vdev param = 2b, value = 33
Notification to UMAC VAP layer
br0: port 3(ath1) entering forwarding state
Configuration fi ieee80211_ioctl_siwmode: imr.ifm_active=393856, new mode=3, valid=1
le: /var/tmp/WSC_ath0.conf
br0: port 2(ath0) entering disabled state
DEVICE IS DOWN ifname=ath0
ath0: Could not DEVICE IS DOWN ifname=ath0
connect to kernel driver
Using interface ath0 with hwaddr c0:a0:bb:f0:05:bb and ssid 'Damage Incorporated'
FWLOG: [41170] WAL_DBGID_SECURITY_ENCR_EN ( )
FWLOG: [41170] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )
FWLOG: [41465] WAL_DBGID_BB_WDOG_TRIGGERED ( 0xa1f9, 0x200008a, 0x0, 0x30 )
br0: port 2(ath0) entering forwarding state
rc is IDLE now!
sh: /etc/sysconfig/gpl_rc_idle.sh: not found
mlme_create_infra_bss : Overriding HT40 channel with HT20 channel
autodetect.c[122] NO IPV4 ADDRESS
autodetect.c[122] NO IPV4 ADDRESS
autodetect.c[122] NO IPV4 ADDRESS
autodetect.c[122] NO IPV4 ADDRESS
autodetect.c[122] NO IPV4 ADDRESS
firewall.c[568] Start IPv6 Firewall
ip6_tables: (C) 2000-2006 Netfilter Core Team
firewall.c[854] flush_ip6tables
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
firewall.c[568] Start IPv6 Firewall
firewall.c[854] flush_ip6tables
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
route.c[33] Start IPv6 Static Routing
macaddr c0a0bbf005bb
########## read_in_uuid:1458 macaddr: c0a0bbf005bb
ip6d.c[140] create IP6D_READY !!
connect.c[155] XXX disconnect
killall: radvd: no process killed
Device "ppp0" does not exist.
Cannot find device "ppp0"
Cannot find device "ppp0"
connect.c[195] IPv6 Autodetection Mode
/var/tmp/dhcp_pd: No such file or directory
Node Added (NC = 1)
Setup LAN interface entry done!
Setup WAN interface entry done!
Node deleted (NC = 0)
TXRX: ol_txrx_peer_find_add_id: peer 87b62000 ID 147
Negotiated: txrates = fffa rxrates = fffa
ASSOC SUCCESS: MAC:fc:c2:de:71:6b:a2
ht numrates 16 , vht mcs set 0xfffa
PHYMODE=0xa NSS=2 FLAGS=0x6233006 max_mpdu=1048575
Node Added (NC = 1)
ol_ath_vap_set_param: VAP param unsupported param:74 value:1
wmi_unified_vdev_install_key_send Setting Key for Macaddress:0xbd05f0bba0c0
Keyix=1 Keylen=32 Keyflags=1 Cipher=2
Keydata=0xc6 0x9e 0x2f 0x3 0x4e 0xfe 0x76 0xf 0x47 0x30 0xb7 0x2f 0x49 0x9a 0x64 0x94 0xc5 0x71 0x37 0x12 0x8f 0xdc 0xa 0x61 0x44 0x1d 0x14 0x54 0x73 0x7f 0xce 0x61
ol_ath_vap_set_param: VAP param unsupported param:74 value:0
TXRX: sec spec for peer 8624d800 (c0:a0:bb:f0:05:bd): mcast key of type 4
Setting vdev param = 1f, value = 1
ol_ath_vap_set_param: VAP param unsupported param:74 value:1
Unicast Keyidx set=5
wmi_unified_vdev_install_key_send Setting Key for Macaddress:0xa26b71dec2fc
Keyix=0 Keylen=16 Keyflags=0 Cipher=4
Keydata=0xc1 0x95 0x56 0xf3 0xe6 0xfd 0x1b 0x6d 0x3f 0xb0 0x49 0x63 0x7d 0x2a 0x50 0x94
ol_ath_vap_set_param: VAP param unsupported param:74 value:0
TXRX: sec spec for peer 87b62000 (fc:c2:de:71:6b:a2): ucast key of type 6
FWLOG: [91196] RATE: ChainMask 3, phymode 10, ni_flags 0x06233006, vht_mcs_set 0xfffa, ht_mcs_set 0xffff
FWLOG: [91257] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )
FWLOG: [91337] WAL_DBGID_SECURITY_UCAST_KEY_SET ( 0x0 )
FWLOG: [91337] WAL_DBGID_SECURITY_ENCR_EN ( )
FWLOG: [91337] WAL_DBGID_SECURITY_ALLOW_DATA ( 0x4310e8 )
arp_hw_add: fail
FWLOG: [92892] WAL_DBGID_TX_BA_SETUP ( 0x4310e8, 0x0, 0x0, 0x40, 0x1 )
Node deleted (NC = 0)
wmi_unified_vdev_install_key_send Setting Key for Macaddress:0xa26b71dec2fc
Keyix=0 Keylen=16 Keyflags=0 Cipher=0
Keydata=0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
TXRX: sec spec for peer 87b62000 (fc:c2:de:71:6b:a2): ucast key of type 0
TXRX: ol_rx_peer_unmap_handler: peer 87b62000 with ID 147 to be unmapped.
FWLOG: [93147] WAL_DBGID_SECURITY_UCAST_KEY_SET ( 0x0 )
Node Added (NC = 1)
Node deleted (NC = 0)
TXRX: ol_txrx_peer_find_add_id: peer 87b62000 ID 147
Negotiated: txrates = fffa rxrates = fffa
ASSOC SUCCESS: MAC:fc:c2:de:71:6b:a2
ht numrates 16 , vht mcs set 0xfffa
PHYMODE=0xa NSS=2 FLAGS=0x6233006 max_mpdu=1048575
Node Added (NC = 1)
ol_ath_vap_set_param: VAP param unsupported param:74 value:1
Unicast Keyidx set=5
wmi_unified_vdev_install_key_send Setting Key for Macaddress:0xa26b71dec2fc
Keyix=0 Keylen=16 Keyflags=0 Cipher=4
Keydata=0x6 0xc0 0xbc 0x35 0x58 0x86 0x31 0x91 0x6e 0x42 0x2f 0x12 0xa1 0x8d 0x27 0x79
ol_ath_vap_set_param: VAP param unsupported param:74 value:0
TXRX: sec spec for peer 87b62000 (fc:c2:de:71:6b:a2): ucast key of type 6
FWLOG: [220540] RATE: ChainMask 3, phymode 10, ni_flags 0x06233006, vht_mcs_set 0xfffa, ht_mcs_set 0xffff
FWLOG: [220628] WAL_DBGID_SECURITY_UCAST_KEY_SET ( 0x0 )
FWLOG: [220628] WAL_DBGID_SECURITY_ENCR_EN ( )
FWLOG: [220628] WAL_DBGID_SECURITY_ALLOW_DATA ( 0x431180 )
arp_hw_add: fail
Node deleted (NC = 0)
wmi_unified_vdev_install_key_send Setting Key for Macaddress:0xa26b71dec2fc
Keyix=0 Keylen=16 Keyflags=0 Cipher=0
Keydata=0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
TXRX: sec spec for peer 87b62000 (fc:c2:de:71:6b:a2): ucast key of type 0
TXRX: ol_rx_peer_unmap_handler: peer 87b62000 with ID 147 to be unmapped.
FWLOG: [222219] WAL_DBGID_TX_BA_SETUP ( 0x431180, 0x0, 0x0, 0x40, 0x1 )
FWLOG: [222475] WAL_DBGID_SECURITY_UCAST_KEY_SET ( 0x0 )
