OpenWrt Forum Archive

Topic: ZyXEL WAP3205 v2 - How to install?

The content of this topic has been archived on 3 May 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

Hi guys,

i have to get OpenWrt on 2 of the AccessPoints described in the Topic. Since they're systems seem to have not enough functionallity for our purposes.
I really tried to follow the instructions on this post (http://wiki.openwrt.org/toh/zyxel/nbg419n) i bought a Console Cable for Raspberry Pi and opened the case. So far, everything was fine.

But the description about the file transfer and connection via TFTP server is simply too inaccurate for me. I've got no clue about how to do it. Can someone please post a tutorial video or a precise instruction? How to use, wich program and where to specify the dataflow parameters, etc.

Thanks in advance,
Fidoro. (sry for bad english)

(Last edited by fidoro on 10 Sep 2014, 23:07)

*push*
Please, can anybody help?
I really need this to be done.

Maybe someone has a better way to flash OpenWRT to the device.
Maybe the creator of the post from the wiki can contact me?
Who was this anyway?

Thanks,
Fidoro.

If ZyXEL WAP3205 v2 == ZyXEL NBG419N v2
there exists topic for porting openwrt to the device.

Yes right. It's the same device.
However, there is no precise instruction on how to install it.
I haven't even got on wich interface the TFTP has to run.
Serial? Lan?
I am so lost with this.

But thanks for your try smile

fidoro wrote:

Yes right. It's the same device.

Ok. There isn't support for the device yet but you can try firmware from that topic.

However, there is no precise instruction on how to install it.
I haven't even got on wich interface the TFTP has to run.
Serial? Lan?

Usually firmware is loaded through lan interface with serial console control.
If you already have serial cable the procedure is simple enough to explain here.

(Last edited by 123serge123 on 25 Sep 2014, 18:30)

First: Thank you for helping me smile

And yes, i got a Serial Cable, and i know how to and where to connect it.

Now i just need someone to explain the procedure.

Edit: Okay, I found out how to connect to the serial console via putty. But I don't know any furher.

(Last edited by fidoro on 25 Sep 2014, 23:37)

If you connect correctly show original firmware boot log.

So, I connected via serial console on COM16, and let it start up.
This ist all output:

U-Boot 1.1.3 (May  3 2012 - 14:40:25)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb0000
spi_wait_nsec: 3c
spi device id: c2 20 17 c2 20 (2017c220)
find flash: MX25L6405D
raspi_read: from:30000 len:1000
.*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 3.6.0.1_b5
--------------------------------------------
ASIC 3352_MP (Port5<->None)
DRAM_CONF_FROM: Boot-Strapping
DRAM_TYPE: DDR2
DRAM_SIZE: 512 Mbits
DRAM_WIDTH: 16 bits
DRAM_TOTAL_WIDTH: 16 bits
TOTAL_MEMORY_SIZE: 64 MBytes
Flash component: SPI Flash
Date:May  3 2012  Time:14:40:25
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

 ##### The CPU freq = 384 MHZ ####
 estimate memory size =64 Mbytes
 uboot: Power LED...on

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   6: To emergency.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
   a: Auto load system code then write to Flash via TFTP.                                                                                                                                          0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
.   Image Name:   Linux Kernel Image
   Created:      2013-08-28  11:38:04 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    3453703 Bytes =  3.3 MB
   Load Address: 80000000
   Entry Point:  80224000
raspi_read: from:50040 len:34b307
.....................................................   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80224000) ...
## Giving linux memsize in MB, 64

Starting kernel ...


LINUX started...

 THIS IS ASIC

 The CPU frequency set to 384 MHz
CPU revision is: 0001964c
Determined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
Built 1 zonelists.  Total pages: 16256
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
cause = d0808000, status = 11000000
PID hash table entries: 256 (order: 8, 1024 bytes)
calculating r4koff... 00177000(1536000)
CPU frequency 384.00 MHz
Using 192.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
detected lzma initramfs
MX25L6405D(c2 2017c220) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
mtd: partition "Kernel" extends beyond the end of device "raspi" -- size truncated to 0x7b0000
squashfs: LZMA suppport for slax.org by jro
Ralink gpio driver initialized
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
rdm_major = 253
Ralink APSoC Ethernet Driver Initilization. v2.1  256 rx/tx descriptors allocated, mtu = 1500!
MAC_ADRH -- : 0x00002828
MAC_ADRL -- : 0x5dfe8ca9
 kernel: NBG-419N v2 Power LED...on
RL this is patch v3
nf_conntrack version 0.5.0 (512 buckets, 4096 max 400 reserved)
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
init started: BusyBox v1.12.1 (2013-08-28 19:23:15 CST)
startAlgorithmics/MIPS FPU Emulator v1.5
ing pid 13, tty '': '/etc_ro/rcS'
mount: mounting none on /sys failed: No such device
mount: mounting none on /proc/bus/usb failed: No such file or directory
Welcome to
     _______  _______  ___     __  ____   _  _   ___
    |  ___  \|   __  ||   |   |__||    \ | || | /  /
    | |___| ||  |__| ||   |__  __ |     \| || |/  /
    |   _   /|   _   ||      ||  || |\     ||     \
    |__| \__\|__| |__||______||__||_| \____||_|\___\

                     =System Architecture Department=

ftpalg: Waiting for message from kernel
insmod: NetUSB.ko: module not found

@@@ BssidNum @@@

@@@ BssidNum @@@
nvram flash is ok
starting pid 49, tty '/dev/ttyS1': '/bin/sh'


BusyBox v1.12.1 (2013-08-28 19:23:15 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

# Password for 'admin' changed
rmmod: ralink_wdt: No such file or directory
rmmod: cls: No such file or directory
rmmod: hw_nat: No such file or directory
rmmod: raeth: No such file or directory
insmod: bridge.ko: module not found
insmod: mii.ko: module not found
insmod: raeth.ko: module not found

phy_tx_ring = 0x00298000, tx_ring = 0xa0298000

phy_rx_ring0 = 0x00299000, rx_ring0 = 0xa0299000
MAC_ADRH -- : 0x00002828
MAC_ADRL -- : 0x5dfe8ca9
RT305x_ESW: Link Status Changed
CDMA_CSG_CFG = 81000007
GDMA1_FWD_CFG = C0710000

##### disable 1st wireless interface #####
rmmod: rt2860v2_ap_net: No such file or directory
rmmod: rt2860v2_ap: No such file or directory
rmmod: rt2860v2_ap_util: No such file or directory
rmmod: rt2860v2_sta_net: No such file or directory
rmmod: rt2860v2_sta: No such file or directory
rmmod: rt2860v2_sta_util: No such file or directory
RT305x_ESW: Link Status Changed
insmod: rt2860v2_ap_util.ko: module not found
rt2860v2_ap: module license 'unspecified' taints kernel.


=== pAd = c001b000, size = 804440 ===

<-- RTMPAllocAdapterBlock, Status=0
insmod: rt2860v2_ap_net.ko: module not found
rmmod: nf_nat_pptp: No such file or directory
rmmod: nf_conntrack_pptp: No such file or directory
rmmod: nf_nat_proto_gre: No such file or directory
rmmod: nf_conntrack_proto_gre: No such file or directory
RX DESC a02ac000  size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
RTMPSetPhyMode: channel is out of range, use first channel=0
MCS Set = ff ff 00 00 01
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
Main bssid = 28:28:5d:fe:8c:a8
<==== rt28xx_init, Status=0
0x1300 = 00064380
vconfig: ioctl error for rem: Invalid argument
vconfig: ioctl error for rem: Invalid argument
rmmod: 8021q: No such file or directory
insmod: 8021q.ko: module not found
vconfig: ioctl error for rem: Invalid argument
eth2.2: Setting MAC address to  28 28 5d fe 8c a9.
VLAN (eth2.2):  Underlying device (eth2) has same MAC, not checking promiscious mode.
ifconfig: ioctl 0x8913 failed: No such device
brctl: bridge br0: No such device or address
iptables v1.4.0rc1: can't initialize iptables table `mangle': Table does not exist (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
Set: phy[2].reg[0] = 3900
Set: phy[3].reg[0] = 3900
Set: phy[4].reg[0] = 3900
ra2880stop()...Done
Free TX/RX Ring Memory!

phy_tx_ring = 0x0043f000, tx_ring = 0xa043f000

phy_rx_ring0 = 0x00260000, rx_ring0 = 0xa0260000
MAC_ADRH -- : 0x00002828
MAC_ADRL -- : 0x5dfe8ca8
CDMA_CSG_CFG = 81000007
GDMA1_FWD_CFG = C0710000
##### restore Ralink ESW to dump switch #####
switch reg write offset=14, value=405555
switch reg write offset=50, value=2001
switch reg write offset=54, value=4003
switch reg write offset=98, value=7f3f
switch reg write offset=e4, value=3f
switch reg write offset=40, value=1002
switch reg write offset=44, value=1001
switch reg write offset=48, value=1001
switch reg write offset=70, value=ffff417e
done.
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
route: ioctl 0x890c failed: No such process
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
ifconfig: ioctl 0x8914 failed: Cannot assign requested address

***** g_wl_interface = ra0 ******

ifconfig: ioctl 0x8913 failed: No such device
/sbin/lan.sh: line 539: dnsmasq: not found
iwpriv ra0 set GuestWLAN_Enable=0
iwpriv ra0 set Mssid1DevBlocking=0.0.0.0
iwpriv ra0 set Mssid1DevBlockingSub=0.0.0.0
iwpriv ra0 set IgmpSnEnable=1
Start  initInterRL debug: AQ_LAN_IP=c0a80102
net!!!!!   systeRL debug: AQ_SHIFT_COUNT=8
m[internet.sh] =RL debug: AQ_HTTP_PORT=50
 0
led=13, on=1, off=4000, blinks,=1, reset=1, time=4000
   system[killall rt2860apd 1>/dev/null 2>&1] = 256
   system[mkdir -p /var/spool/cron/crontabs] = 0
   system[rm -f /var/spool/cron/crontabs/scheduler] = 0
   system[cat /var/spool/cron/crontabs/temp.dat > /var/spool/cron/crontabs/admin] = 0
   system[rm -f /var/spool/cron/crontabs/temp.dat] = 0
killall: crond: no process killed
   system[killall crond] = 256
   system[iwpriv ra0 set RadioOn=0] = 0
led=14, on=1, off=4000, blinks,=1, reset=1, time=4000
   system[gpio l 14 0 4000 0 1 4000] = 0
killall: ntp.sh: no process killed
   system[killall ntp.sh] = 256
   system[ntp.sh &] = 0
sh: ddns.sh: not found
   system[ddns.sh] = 32512
Enter udps


   system[udps &] = 0
sh: cplange.sh: not found
   system[cplange.sh &] = 0
cat: can't open '/var/run/wscd.pid.ra0': No such file or directory
kill: you need to specify whom to kill
   system[kill -9 `cat /var/run/wscd.pid.ra0`] = 256
   system[iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1] = 0
   system[iwpriv ra0 set WscConfMode=7] = 0
   system[route add -host 239.255.255.250 dev br0 1>/dev/null 2>&1] = 0
   system[wscd -m 1 -a 192.168.1.2 -i ra0 &] = 0
   system[echo '1' >  /tmp/syslodg_exist] = 0
   system[syslogd -C8 1>/dev/null 2>&1] = 0
   system[klogd 1>/dev/null 2>&1] = 0
libupnp: using UDP SSDP_PORT = 1900
Ntpserver is 192.5.41.41
connect: Network is unreachable
   system[killall -q zebra] = 256
sleep 4.....
   system[killall -q ripd] = 256
E2P: (181)
Bootloader is newer version (00b5)
BoA: reload parameter into BoA webserver!
The rmPort is 80
Ntpserver is 192.5.41.209
connect: Network is unreachable
sleep 4.....
Ntpserver is 203.117.180.36
connect: Network is unreachable
sleep 4.....
Ntpserver is 131.188.3.220
connect: Network is unreachable
sleep 4.....
Ntpserver is 130.149.17.8
sleep 60.....

Ok. As expected your device use standard u-boot loader. You can see u-boot menu at the beginning of log. This menu contain emergency recovery, so I recommend to search description of this recovery procedure (just for garanted way to restore original zyxel firmware).
Next steps for flashing openwrt firmware:
1. Interrupt boot and get u-boot command promt (hit '4' in boot menu).
2. In u-boot console setup ip configuration. Usually '?' - generic help, printenv/setenv - see/show params. We interested in 'ipaddr' and 'serverip' - address of router and tftp-server (your PC).
3. Prepare your PC (setup static ip-address == serverip), install tftp-server (e.g tftp32.exe for windows) and put firmware (e.g 'firmware.bin') to tftp-server directory.
4. Prepare flash (typically 'erase linux' command - see output of '? erase' in u-boot promt).
5. Connect PC and router with ethernet cable.
6. With u-boot command 'tftpboot 80100000 firmware.bin' get firmware from PC to RAM.
7. With u-boot command 'cp.linux 80100000' write firmware fom RAM to flash chip.
8. Reboot.
WARNING!!! After successful step 4 your router loose any firmware so to restore you need get success in steps 5-7 or use emergency recovery procedure from zyxel!

Thank you. Everything worked like you said.

This is new output after hitting 'restart' in the console.

RT3352 # reset


U-Boot 1.1.3 (May  3 2012 - 14:40:25)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb0000
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 3c
spi device id: c2 20 17 c2 20 (2017c220)
find flash: MX25L6405D
raspi_read: from:30000 len:1000
.*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 3.6.0.1_b5
--------------------------------------------
ASIC 3352_MP (Port5<->None)
DRAM_CONF_FROM: Boot-Strapping
DRAM_TYPE: DDR2
DRAM_SIZE: 512 Mbits
DRAM_WIDTH: 16 bits
DRAM_TOTAL_WIDTH: 16 bits
TOTAL_MEMORY_SIZE: 64 MBytes
Flash component: SPI Flash
Date:May  3 2012  Time:14:40:25
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

 ##### The CPU freq = 384 MHZ ####
 estimate memory size =64 Mbytes
 uboot: Power LED...on

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   6: To emergency.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
   a: Auto load system code then write to Flash via TFTP.                     0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
.   Image Name:   MIPS OpenWrt Linux-3.14.16
   Created:      2014-09-09   0:27:26 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1106422 Bytes =  1.1 MB
   Load Address: 80000000
   Entry Point:  80000000
raspi_read: from:50040 len:10e1f6
.................   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 3.14.16 (openwrt@gb-13) (gcc version 4.8.3 (OpenWrt                                                                                                                     /Linaro GCC 4.8-2014.04 r42446) ) #1 Tue Sep 9 00:25:24 UTC 2014
[    0.000000] SoC Type: Ralink RT3352 id:1 rev:6
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001964c (MIPS 24KEc)
[    0.000000] MIPS: machine is ZyXEL NBG-419N
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 byt                                                                                                                     es
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag                                                                                                                     es: 16256
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs                                                                                                                     2
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00037462
[    0.000000] Readback ErrCtl register=00037462
[    0.000000] Memory: 61516K/65536K available (2428K kernel code, 123K rwdata,                                                                                                                      472K rodata, 168K init, 183K bss, 4020K reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 384MHz
[    0.000000] clocksource_of_init: no matching clocksources found
[    0.000000] Calibrating delay loop... 255.59 BogoMIPS (lpj=1277952)
[    0.070000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.100000] pinctrl core: initialized pinctrl subsystem
[    0.110000] NET: Registered protocol family 16
[    0.130000] pinmux core: rt2880-pinmux does not support function sdram
[    0.140000] rt2880-pinmux pinctrl.1: invalid function sdram in map table
[    0.170000] bio: create slab <bio-0> at 0
[    0.180000] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.190000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.200000] Switched to clocksource MIPS
[    0.210000] NET: Registered protocol family 2
[    0.220000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.230000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.250000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.260000] TCP: reno registered
[    0.270000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.280000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.290000] NET: Registered protocol family 1
[    0.300000] rt-timer 10000100.timer: maximum frequency is 7812Hz
[    0.320000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.370000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.380000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT                                                                                                                     Y) (c) 2001-2006 Red Hat, Inc.
[    0.400000] msgmni has been set to 120
[    0.410000] io scheduler noop registered
[    0.420000] io scheduler deadline registered (default)
[    0.430000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.460000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud                                                                                                                      = 2500000) is a 16550A
[    0.480000] console [ttyS0] enabled
[    0.480000] console [ttyS0] enabled
[    0.490000] bootconsole [early0] disabled
[    0.490000] bootconsole [early0] disabled
[    0.510000] of-flash 1f000000.cfi: do_map_probe() failed
[    0.530000] eth0: done loading
[    0.540000] rt2880_wdt 10000120.watchdog: Initialized
[    0.560000] TCP: cubic registered
[    0.560000] NET: Registered protocol family 17
[    0.570000] Bridge firewalling registered
[    0.580000] 8021q: 802.1Q VLAN Support v1.8
[    0.590000] VFS: Cannot open root device "(null)" or unknown-block(0,0): erro                                                                                                                     r -6
[    0.610000] Please append a correct "root=" boot option; here are the availab                                                                                                                     le partitions:
[    0.620000] Kernel panic - not syncing: VFS: Unable to mount root fs on unkno                                                                                                                     wn-block(0,0)
[    2.580000] rt305x-esw 10110000.esw: link changed 0x01
[   20.980000] rt305x-esw 10110000.esw: link changed 0x00
[   22.650000] rt305x-esw 10110000.esw: link changed 0x01
[   31.000000] rt305x-esw 10110000.esw: link changed 0x00
[   32.760000] rt305x-esw 10110000.esw: link changed 0x01
[   59.030000] rt305x-esw 10110000.esw: link changed 0x00
[   60.650000] rt305x-esw 10110000.esw: link changed 0x01

Does this say, everything worked fine?

No. You flash sucssesfully firmware for Zyxel nbg-419n but it can't work with your flash chip. Your need flash firmware from the topic above pointed (there exists url for nbg-419n v2).
And  good news - you now can flash any firmware from serial console (including original zyxel firmware) smile

123serge123 wrote:

Your need flash firmware from the topic above pointed (there exists url for nbg-419n v2).

Which exactly? I used this one: http://downloads.openwrt.org/snapshots/ … pgrade.bin. I can't find any other (neither in the post) which seem to be suitable for the device.
big_smile

If you carefully read the topic you see this link.
Just start with openwrt-ramips-rt305x-nbg419v2-bb-rc3-squashfs-sysupgrade.v7.bin
If leds or buttons work incorrectly, I'll patch image for your model. But our main target is to start openwrt firmware in your device.

(Last edited by 123serge123 on 26 Sep 2014, 18:49)

fidoro wrote:
123serge123 wrote:

Your need flash firmware from the topic above pointed (there exists url for nbg-419n v2).

Which exactly? I used this one: http://downloads.openwrt.org/snapshots/ … pgrade.bin. I can't find any other (neither in the post) which seem to be suitable for the device.
big_smile

Hello,

How is it going ? Did you get it work ? I bought a wap3205 V2 and like to install openwrt. Do you get switch (AP/UR/CL) working ?

The discussion might have continued from here.