i compiled with the changes above but without success.
dmesg shows that everything after 16mb?! was formated?
dmesg from first boot:
[ 0.000000] Linux version 3.10.49 (sorlas@SorlasDebian) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r43483) ) #1 Fri Dec 12 09:32:38 CET 2014
[ 0.000000] MyLoader: sysp=6c5fed42, boardp=be725d54, parts=dc5393f0
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9330 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 803109b0, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: board=TL-MR13U console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61208k/65536k available (2240k kernel code, 4328k reserved, 602k data, 228k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.100000] MIPS: machine is TP-LINK TL-MR13U v1
[ 0.410000] bio: create slab <bio-0> at 0
[ 0.420000] Switching to clocksource MIPS
[ 0.430000] NET: Registered protocol family 2
[ 0.430000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.430000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.430000] TCP: Hash tables configured (established 512 bind 512)
[ 0.440000] TCP: reno registered
[ 0.440000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.450000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.460000] NET: Registered protocol family 1
[ 0.460000] PCI: CLS 0 bytes, default 32
[ 0.480000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.480000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.490000] msgmni has been set to 119
[ 0.500000] io scheduler noop registered
[ 0.500000] io scheduler deadline registered (default)
[ 0.510000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.510000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[ 0.520000] console [ttyATH0] enabled, bootconsole disabled
[ 0.530000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.540000] m25p80 spi0.0: found w25q256, expected m25p80
[ 0.540000] m25p80 spi0.0: w25q256 (32768 Kbytes)
[ 0.550000] 5 tp-link partitions found on MTD device spi0.0
[ 0.550000] Creating 5 MTD partitions on "spi0.0":
[ 0.560000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.570000] 0x000000020000-0x000000122104 : "kernel"
[ 0.570000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.580000] 0x000000122104-0x000001ff0000 : "rootfs"
[ 0.590000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.600000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.610000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.610000] 0x0000002f0000-0x000001ff0000 : "rootfs_data"
[ 0.620000] 0x000001ff0000-0x000002000000 : "art"
[ 0.620000] 0x000000020000-0x000001ff0000 : "firmware"
[ 0.650000] libphy: ag71xx_mdio: probed
[ 1.200000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[ 1.210000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 1.210000] TCP: cubic registered
[ 1.220000] NET: Registered protocol family 17
[ 1.220000] 8021q: 802.1Q VLAN Support v1.8
[ 1.240000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.250000] Freeing unused kernel memory: 228K (80327000 - 80360000)
[ 5.190000] usbcore: registered new interface driver usbfs
[ 5.190000] usbcore: registered new interface driver hub
[ 5.200000] usbcore: registered new device driver usb
[ 5.210000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.210000] ehci-platform: EHCI generic platform driver
[ 5.220000] ehci-platform ehci-platform: EHCI Host Controller
[ 5.220000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 5.230000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 5.260000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 5.260000] hub 1-0:1.0: USB hub found
[ 5.260000] hub 1-0:1.0: 1 port detected
[ 5.270000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 9.290000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[ 9.290000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 10.310000] eth0: link up (100Mbps/Full duplex)
[ 9.300000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[ 158.460000] jffs2: notice: (307) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 158.740000] eth0: link down
[ 160.440000] NET: Registered protocol family 10
[ 160.460000] nf_conntrack version 0.5.0 (959 buckets, 3836 max)
[ 160.470000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 160.480000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 160.490000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 160.500000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 160.550000] xt_time: kernel timezone is -0000
[ 160.590000] cfg80211: Calling CRDA to update world regulatory domain
[ 160.590000] cfg80211: World regulatory domain updated:
[ 160.600000] cfg80211: DFS Master region: unset
[ 160.600000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 160.610000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 160.620000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 160.630000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 160.630000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 160.640000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 160.650000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 160.660000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 160.670000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 160.750000] PPP generic driver version 2.4.2
[ 160.750000] NET: Registered protocol family 24
[ 160.810000] ath: EEPROM regdomain: 0x0
[ 160.810000] ath: EEPROM indicates default country code should be used
[ 160.810000] ath: doing EEPROM country->regdmn map search
[ 160.810000] ath: country maps to regdmn code: 0x3a
[ 160.810000] ath: Country alpha2 being used: US
[ 160.810000] ath: Regpair used: 0x3a
[ 160.830000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 160.840000] cfg80211: Calling CRDA for country: US
[ 160.850000] cfg80211: Regulatory domain changed to country: US
[ 160.850000] cfg80211: DFS Master region: FCC
[ 160.850000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 160.860000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 160.870000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
[ 160.880000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[ 160.890000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 160.900000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 160.900000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[ 169.920000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 169.920000] device eth0 entered promiscuous mode
[ 169.930000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 170.480000] eth0: link up (100Mbps/Full duplex)
[ 170.480000] br-lan: port 1(eth0) entered forwarding state
[ 170.490000] br-lan: port 1(eth0) entered forwarding state
[ 170.490000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 170.510000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 172.490000] br-lan: port 1(eth0) entered forwarding state
Then i recovered the art partition, but still no wifi
here's dmesg after art recovery
BusyBox v1.22.1 (2014-12-12 09:24:22 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (Barrier Breaker, r43483)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme de Cacao
-----------------------------------------------------
root@OpenWrt:~# ifconfig
br-lan Link encap:Ethernet HWaddr 08:57:00:57:A2:2E
inet addr:192.168.2.236 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::a57:ff:fe57:a22e/64 Scope:Link
inet6 addr: fd1a:8487:654d::1/60 Scope:Global
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:77 errors:0 dropped:0 overruns:0 frame:0
TX packets:76 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:9369 (9.1 KiB) TX bytes:9650 (9.4 KiB)
eth0 Link encap:Ethernet HWaddr 08:57:00:57:A2:2E
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:77 errors:0 dropped:0 overruns:0 frame:0
TX packets:77 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:10447 (10.2 KiB) TX bytes:9696 (9.4 KiB)
Interrupt:4
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:18 errors:0 dropped:0 overruns:0 frame:0
TX packets:18 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1552 (1.5 KiB) TX bytes:1552 (1.5 KiB)
root@OpenWrt:~# dmesg
[ 0.000000] Linux version 3.10.49 (sorlas@SorlasDebian) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r43483) ) #1 Fri Dec 12 09:32:38 CET 2014
[ 0.000000] MyLoader: sysp=6c5fed42, boardp=be725d54, parts=dc5393f0
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9330 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 803109b0, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: board=TL-MR13U console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61208k/65536k available (2240k kernel code, 4328k reserved, 602k data, 228k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.100000] MIPS: machine is TP-LINK TL-MR13U v1
[ 0.410000] bio: create slab <bio-0> at 0
[ 0.420000] Switching to clocksource MIPS
[ 0.430000] NET: Registered protocol family 2
[ 0.430000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.430000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.430000] TCP: Hash tables configured (established 512 bind 512)
[ 0.440000] TCP: reno registered
[ 0.440000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.450000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.460000] NET: Registered protocol family 1
[ 0.460000] PCI: CLS 0 bytes, default 32
[ 0.480000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.480000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.490000] msgmni has been set to 119
[ 0.500000] io scheduler noop registered
[ 0.500000] io scheduler deadline registered (default)
[ 0.510000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.510000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[ 0.520000] console [ttyATH0] enabled, bootconsole disabled
[ 0.530000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.540000] m25p80 spi0.0: found w25q256, expected m25p80
[ 0.540000] m25p80 spi0.0: w25q256 (32768 Kbytes)
[ 0.550000] 5 tp-link partitions found on MTD device spi0.0
[ 0.550000] Creating 5 MTD partitions on "spi0.0":
[ 0.560000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.570000] 0x000000020000-0x000000122104 : "kernel"
[ 0.570000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.580000] 0x000000122104-0x000001ff0000 : "rootfs"
[ 0.590000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.600000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.610000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.610000] 0x0000002f0000-0x000001ff0000 : "rootfs_data"
[ 0.620000] 0x000001ff0000-0x000002000000 : "art"
[ 0.620000] 0x000000020000-0x000001ff0000 : "firmware"
[ 0.650000] libphy: ag71xx_mdio: probed
[ 1.200000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[ 1.210000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 1.210000] TCP: cubic registered
[ 1.220000] NET: Registered protocol family 17
[ 1.220000] 8021q: 802.1Q VLAN Support v1.8
[ 1.240000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.250000] Freeing unused kernel memory: 228K (80327000 - 80360000)
[ 5.190000] usbcore: registered new interface driver usbfs
[ 5.190000] usbcore: registered new interface driver hub
[ 5.200000] usbcore: registered new device driver usb
[ 5.210000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.210000] ehci-platform: EHCI generic platform driver
[ 5.220000] ehci-platform ehci-platform: EHCI Host Controller
[ 5.220000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 5.230000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 5.260000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 5.260000] hub 1-0:1.0: USB hub found
[ 5.260000] hub 1-0:1.0: 1 port detected
[ 5.270000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 8.240000] eth0: link up (100Mbps/Full duplex)
[ 9.480000] jffs2: notice: (307) jffs2_build_xattr_subsystem: complete building xattr subsystem, 16 of xdatum (0 unchecked, 15 orphan) and 27 of xref (0 dead, 15 orphan) found.
[ 9.520000] eth0: link down
[ 11.090000] NET: Registered protocol family 10
[ 11.110000] nf_conntrack version 0.5.0 (959 buckets, 3836 max)
[ 11.120000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.130000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 11.140000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 11.150000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.210000] xt_time: kernel timezone is -0000
[ 11.250000] cfg80211: Calling CRDA to update world regulatory domain
[ 11.250000] cfg80211: World regulatory domain updated:
[ 11.260000] cfg80211: DFS Master region: unset
[ 11.260000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 11.270000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.280000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.290000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.290000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.300000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 11.310000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 11.320000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.330000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 11.400000] PPP generic driver version 2.4.2
[ 11.410000] NET: Registered protocol family 24
[ 11.470000] ath: EEPROM regdomain: 0x0
[ 11.470000] ath: EEPROM indicates default country code should be used
[ 11.470000] ath: doing EEPROM country->regdmn map search
[ 11.470000] ath: country maps to regdmn code: 0x3a
[ 11.470000] ath: Country alpha2 being used: US
[ 11.470000] ath: Regpair used: 0x3a
[ 11.480000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 11.490000] cfg80211: Calling CRDA for country: US
[ 11.500000] cfg80211: Regulatory domain changed to country: US
[ 11.500000] cfg80211: DFS Master region: FCC
[ 11.500000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 11.510000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 11.520000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
[ 11.530000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[ 11.540000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 11.550000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 11.550000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[ 20.260000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 20.260000] device eth0 entered promiscuous mode
[ 20.270000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 20.950000] eth0: link up (100Mbps/Full duplex)
[ 20.950000] br-lan: port 1(eth0) entered forwarding state
[ 20.960000] br-lan: port 1(eth0) entered forwarding state
[ 20.960000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 20.980000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 22.960000] br-lan: port 1(eth0) entered forwarding state
(Last edited by Sorlas on 12 Dec 2014, 10:05)