Hi hnyman,
Sorry for my late reply... At this moment I'm also using the WWAN to test the script... but without success...
As daniel, I confirm the https://nos.portal.fon.com... So I made some changes in the script:
#!/bin/sh
if [ "$INTERFACE" = "wwan" ] && ([ "$ACTION" = "ifup" ] || [ "$ACTION" = "update" ]); then
wget -qO- --output-document=portal.html --no-check-certificate --save-cookies=cookie --keep-session-cookies https://www.google.pt
POST_URL=$(cat portal.html | grep 'action="https://nos' | cut -d \" -f 4)
if [ -n "$POST_URL" ]; then
wget -qO- --output-document=/dev/null --no-check-certificate --load-cookies=cookie --keep-session-cookies --post-data="USERNAME=mail@gmail.com&PASSWORD=123456&remember=on" $POST_URL
fi
rm cookie portal.html
fi
See also these logs: (MAC ADDRESS OF "NOS FON" IS: aa:bb:cc:dd:ee:ff)... I think the script does not start ...
LOGREAD LOG:
root@OpenWrt:~# logread
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.060000] Mount-cache hash table entries: 512
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.070000] NET: Registered protocol family 16
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.070000] MIPS: machine is TP-LINK Archer C7
Mon May 4 22:36:20 2015 kern.warn kernel: [ 0.080000] ar724x-pci ar724x-pci.0: PCIe link is down
Mon May 4 22:36:20 2015 kern.warn kernel: [ 0.080000] registering PCI controller with io_map_base unset
Mon May 4 22:36:20 2015 kern.warn kernel: [ 0.090000] registering PCI controller with io_map_base unset
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.500000] bio: create slab <bio-0> at 0
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.500000] PCI host bridge to bus 0000:00
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.510000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.510000] pci_bus 0000:00: root bus resource [io 0x0000]
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.520000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
Mon May 4 22:36:20 2015 kern.debug kernel: [ 0.520000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.520000] PCI host bridge to bus 0000:01
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.530000] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.530000] pci_bus 0000:01: root bus resource [io 0x0001]
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.540000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
Mon May 4 22:36:20 2015 kern.debug kernel: [ 0.540000] pci 0000:01:00.0: [168c:003c] type 00 class 0x028000
Mon May 4 22:36:20 2015 kern.debug kernel: [ 0.540000] pci 0000:01:00.0: reg 10: [mem 0x00000000-0x001fffff 64bit]
Mon May 4 22:36:20 2015 kern.debug kernel: [ 0.540000] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
Mon May 4 22:36:20 2015 kern.debug kernel: [ 0.540000] pci 0000:01:00.0: supports D1 D2
Mon May 4 22:36:20 2015 kern.debug kernel: [ 0.540000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.540000] pci 0000:01:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.550000] pci 0000:01:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.550000] pci 0000:01:00.0: using irq 41 for pin 1
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.560000] Switching to clocksource MIPS
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.560000] NET: Registered protocol family 2
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.570000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.570000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.570000] TCP: Hash tables configured (established 1024 bind 1024)
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.580000] TCP: reno registered
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.600000] NET: Registered protocol family 1
Mon May 4 22:36:20 2015 kern.debug kernel: [ 0.600000] PCI: CLS 0 bytes, default 32
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.610000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.620000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.630000] msgmni has been set to 246
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.630000] io scheduler noop registered
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.640000] io scheduler deadline registered (default)
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.640000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.670000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.680000] console [ttyS0] enabled, bootconsole disabled
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.690000] ath79-spi ath79-spi: master is unqueued, this is deprecated
Mon May 4 22:36:20 2015 kern.warn kernel: [ 0.700000] m25p80 spi0.0: found s25fl129p1, expected m25p80
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.700000] m25p80 spi0.0: s25fl129p1 (16384 Kbytes)
Mon May 4 22:36:20 2015 kern.notice kernel: [ 0.710000] 5 tp-link partitions found on MTD device spi0.0
Mon May 4 22:36:20 2015 kern.notice kernel: [ 0.720000] Creating 5 MTD partitions on "spi0.0":
Mon May 4 22:36:20 2015 kern.notice kernel: [ 0.720000] 0x000000000000-0x000000020000 : "u-boot"
Mon May 4 22:36:20 2015 kern.notice kernel: [ 0.730000] 0x000000020000-0x00000012e660 : "kernel"
Mon May 4 22:36:20 2015 kern.warn kernel: [ 0.730000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Mon May 4 22:36:20 2015 kern.notice kernel: [ 0.750000] 0x00000012e660-0x000000ff0000 : "rootfs"
Mon May 4 22:36:20 2015 kern.warn kernel: [ 0.750000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Mon May 4 22:36:20 2015 kern.notice kernel: [ 0.760000] mtd: device 2 (rootfs) set to be root filesystem
Mon May 4 22:36:20 2015 kern.notice kernel: [ 0.770000] 1 squashfs-split partitions found on MTD device rootfs
Mon May 4 22:36:20 2015 kern.notice kernel: [ 0.780000] 0x000000390000-0x000000ff0000 : "rootfs_data"
Mon May 4 22:36:20 2015 kern.notice kernel: [ 0.780000] 0x000000ff0000-0x000001000000 : "art"
Mon May 4 22:36:20 2015 kern.notice kernel: [ 0.790000] 0x000000020000-0x000000ff0000 : "firmware"
Mon May 4 22:36:20 2015 kern.info kernel: [ 0.830000] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
Mon May 4 22:36:20 2015 kern.info kernel: [ 2.070000] libphy: ag71xx_mdio: probed
Mon May 4 22:36:20 2015 kern.info kernel: [ 2.620000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
Mon May 4 22:36:20 2015 kern.info kernel: [ 2.640000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
Mon May 4 22:36:20 2015 kern.info kernel: [ 3.190000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII
Mon May 4 22:36:20 2015 kern.info kernel: [ 3.200000] TCP: cubic registered
Mon May 4 22:36:20 2015 kern.info kernel: [ 3.200000] NET: Registered protocol family 17
Mon May 4 22:36:20 2015 kern.notice kernel: [ 3.210000] Bridge firewalling registered
Mon May 4 22:36:20 2015 kern.info kernel: [ 3.210000] 8021q: 802.1Q VLAN Support v1.8
Mon May 4 22:36:20 2015 kern.info kernel: [ 3.230000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Mon May 4 22:36:20 2015 kern.info kernel: [ 3.230000] Freeing unused kernel memory: 272K (8034c000 - 80390000)
Mon May 4 22:36:20 2015 kern.info kernel: [ 5.770000] usbcore: registered new interface driver usbfs
Mon May 4 22:36:20 2015 kern.info kernel: [ 5.780000] usbcore: registered new interface driver hub
Mon May 4 22:36:20 2015 kern.info kernel: [ 5.780000] usbcore: registered new device driver usb
Mon May 4 22:36:20 2015 kern.info kernel: [ 5.790000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Mon May 4 22:36:20 2015 kern.info kernel: [ 5.800000] ehci-platform: EHCI generic platform driver
Mon May 4 22:36:20 2015 kern.info kernel: [ 5.800000] ehci-platform ehci-platform.0: EHCI Host Controller
Mon May 4 22:36:20 2015 kern.info kernel: [ 5.810000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
Mon May 4 22:36:20 2015 kern.info kernel: [ 5.820000] ehci-platform ehci-platform.0: TX-TX IDP fix enabled
Mon May 4 22:36:20 2015 kern.info kernel: [ 5.830000] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
Mon May 4 22:36:20 2015 kern.info kernel: [ 5.850000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
Mon May 4 22:36:20 2015 kern.info kernel: [ 5.850000] hub 1-0:1.0: USB hub found
Mon May 4 22:36:20 2015 kern.info kernel: [ 5.860000] hub 1-0:1.0: 1 port detected
Mon May 4 22:36:20 2015 kern.info kernel: [ 5.860000] ehci-platform ehci-platform.1: EHCI Host Controller
Mon May 4 22:36:20 2015 kern.info kernel: [ 5.870000] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
Mon May 4 22:36:20 2015 kern.info kernel: [ 5.880000] ehci-platform ehci-platform.1: TX-TX IDP fix enabled
Mon May 4 22:36:20 2015 kern.info kernel: [ 5.880000] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
Mon May 4 22:36:20 2015 kern.info kernel: [ 5.910000] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
Mon May 4 22:36:20 2015 kern.info kernel: [ 5.910000] hub 2-0:1.0: USB hub found
Mon May 4 22:36:20 2015 kern.info kernel: [ 5.920000] hub 2-0:1.0: 1 port detected
Mon May 4 22:36:20 2015 kern.info kernel: [ 6.330000] usb 2-1: new high-speed USB device number 2 using ehci-platform
Mon May 4 22:36:20 2015 kern.info kernel: [ 6.370000] eth1: link up (1000Mbps/Full duplex)
Mon May 4 22:36:20 2015 kern.notice kernel: [ 9.710000] jffs2: notice: (363) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 15 of xref (0 dead, 1 orphan) found.
Mon May 4 22:36:20 2015 kern.info kernel: [ 9.800000] eth1: link down
Mon May 4 22:36:20 2015 kern.info kernel: [ 11.250000] NET: Registered protocol family 10
Mon May 4 22:36:20 2015 kern.info kernel: [ 11.260000] nf_conntrack version 0.5.0 (1973 buckets, 7892 max)
Mon May 4 22:36:20 2015 kern.info kernel: [ 11.270000] ip6_tables: (C) 2000-2006 Netfilter Core Team
Mon May 4 22:36:20 2015 kern.info kernel: [ 11.290000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
Mon May 4 22:36:20 2015 kern.info kernel: [ 11.290000] Backport generated by backports.git backports-20140320-37-g5c33da0
Mon May 4 22:36:20 2015 kern.info kernel: [ 11.320000] cfg80211: Calling CRDA to update world regulatory domain
Mon May 4 22:36:20 2015 kern.info kernel: [ 11.320000] cfg80211: World regulatory domain updated:
Mon May 4 22:36:20 2015 kern.info kernel: [ 11.330000] cfg80211: DFS Master region: unset
Mon May 4 22:36:20 2015 kern.info kernel: [ 11.330000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Mon May 4 22:36:20 2015 kern.info kernel: [ 11.340000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
Mon May 4 22:36:20 2015 kern.info kernel: [ 11.350000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
Mon May 4 22:36:20 2015 kern.info kernel: [ 11.360000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
Mon May 4 22:36:20 2015 kern.info kernel: [ 11.370000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
Mon May 4 22:36:20 2015 kern.info kernel: [ 11.370000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
Mon May 4 22:36:20 2015 kern.info kernel: [ 11.380000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
Mon May 4 22:36:20 2015 kern.info kernel: [ 11.390000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
Mon May 4 22:36:20 2015 kern.info kernel: [ 11.400000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
Mon May 4 22:36:20 2015 kern.info kernel: [ 11.460000] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
Mon May 4 22:36:20 2015 kern.warn kernel: [ 11.460000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
Mon May 4 22:36:20 2015 kern.info kernel: [ 11.770000] ath10k: pci irq legacy irq_mode 0 reset_mode 0
Mon May 4 22:36:20 2015 kern.warn kernel: [ 11.870000] ath10k: otp stream is empty, using board.bin contents
Mon May 4 22:36:20 2015 kern.info kernel: [ 13.010000] ath10k: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.1.467.2-1 api 2 htt 2.1
Mon May 4 22:36:20 2015 kern.debug kernel: [ 13.550000] ath: EEPROM regdomain: 0x0
Mon May 4 22:36:20 2015 kern.debug kernel: [ 13.550000] ath: EEPROM indicates default country code should be used
Mon May 4 22:36:20 2015 kern.debug kernel: [ 13.550000] ath: doing EEPROM country->regdmn map search
Mon May 4 22:36:20 2015 kern.debug kernel: [ 13.550000] ath: country maps to regdmn code: 0x3a
Mon May 4 22:36:20 2015 kern.debug kernel: [ 13.550000] ath: Country alpha2 being used: US
Mon May 4 22:36:20 2015 kern.debug kernel: [ 13.550000] ath: Regpair used: 0x3a
Mon May 4 22:36:20 2015 kern.info kernel: [ 13.560000] cfg80211: Calling CRDA for country: US
Mon May 4 22:36:20 2015 kern.info kernel: [ 13.570000] cfg80211: Regulatory domain changed to country: US
Mon May 4 22:36:20 2015 kern.info kernel: [ 13.570000] cfg80211: DFS Master region: FCC
Mon May 4 22:36:20 2015 kern.info kernel: [ 13.580000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Mon May 4 22:36:20 2015 kern.info kernel: [ 13.590000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
Mon May 4 22:36:20 2015 kern.info kernel: [ 13.590000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
Mon May 4 22:36:20 2015 kern.info kernel: [ 13.600000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
Mon May 4 22:36:20 2015 kern.info kernel: [ 13.610000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
Mon May 4 22:36:20 2015 kern.info kernel: [ 13.620000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
Mon May 4 22:36:20 2015 kern.info kernel: [ 13.650000] ip_tables: (C) 2000-2006 Netfilter Core Team
Mon May 4 22:36:20 2015 kern.info kernel: [ 13.690000] xt_time: kernel timezone is -0000
Mon May 4 22:36:20 2015 kern.info kernel: [ 13.710000] PPP generic driver version 2.4.2
Mon May 4 22:36:20 2015 kern.info kernel: [ 13.720000] NET: Registered protocol family 24
Mon May 4 22:36:20 2015 kern.debug kernel: [ 13.730000] ath: EEPROM regdomain: 0x0
Mon May 4 22:36:20 2015 kern.debug kernel: [ 13.730000] ath: EEPROM indicates default country code should be used
Mon May 4 22:36:20 2015 kern.debug kernel: [ 13.730000] ath: doing EEPROM country->regdmn map search
Mon May 4 22:36:20 2015 kern.debug kernel: [ 13.730000] ath: country maps to regdmn code: 0x3a
Mon May 4 22:36:20 2015 kern.debug kernel: [ 13.730000] ath: Country alpha2 being used: US
Mon May 4 22:36:20 2015 kern.debug kernel: [ 13.730000] ath: Regpair used: 0x3a
Mon May 4 22:36:20 2015 kern.debug kernel: [ 13.740000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
Mon May 4 22:36:20 2015 kern.info kernel: [ 13.750000] ieee80211 phy1: Atheros AR9550 Rev:0 mem=0xb8100000, irq=47
Mon May 4 22:36:22 2015 authpriv.info dropbear[845]: Not backgrounding
Mon May 4 22:36:24 2015 kern.info kernel: [ 20.670000] eth1: link up (1000Mbps/Full duplex)
Mon May 4 22:36:24 2015 kern.info kernel: [ 20.670000] device eth1 entered promiscuous mode
Mon May 4 22:36:24 2015 kern.info kernel: [ 20.680000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
Mon May 4 22:36:24 2015 kern.info kernel: [ 20.700000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Mon May 4 22:36:25 2015 kern.info kernel: [ 21.670000] br-lan: port 1(eth1) entered forwarding state
Mon May 4 22:36:25 2015 kern.info kernel: [ 21.670000] br-lan: port 1(eth1) entered forwarding state
Mon May 4 22:36:25 2015 kern.info kernel: [ 21.710000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Mon May 4 22:36:25 2015 kern.info kernel: [ 21.850000] eth0: link up (1000Mbps/Full duplex)
Mon May 4 22:36:25 2015 kern.info kernel: [ 21.850000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Mon May 4 22:36:27 2015 kern.warn kernel: [ 23.090000] ath10k: otp stream is empty, using board.bin contents
Mon May 4 22:36:27 2015 kern.info kernel: [ 23.670000] br-lan: port 1(eth1) entered forwarding state
Mon May 4 22:36:27 2015 kern.info kernel: [ 23.940000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Mon May 4 22:36:27 2015 kern.info kernel: [ 23.960000] IPv6: ADDRCONF(NETDEV_UP): wlan1-1: link is not ready
Mon May 4 22:36:27 2015 kern.info kernel: [ 23.970000] device wlan0 entered promiscuous mode
Mon May 4 22:36:27 2015 kern.info kernel: [ 23.980000] device wlan1-1 entered promiscuous mode
Mon May 4 22:36:30 2015 kern.info kernel: [ 26.170000] br-lan: port 2(wlan0) entered forwarding state
Mon May 4 22:36:30 2015 kern.info kernel: [ 26.170000] br-lan: port 2(wlan0) entered forwarding state
Mon May 4 22:36:30 2015 kern.info kernel: [ 26.180000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Mon May 4 22:36:31 2015 kern.info kernel: [ 27.050000] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
Mon May 4 22:36:31 2015 kern.info kernel: [ 27.920000] wlan1: authenticate with aa:bb:cc:dd:ee:ff
Mon May 4 22:36:31 2015 kern.info kernel: [ 27.930000] wlan1: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
Mon May 4 22:36:31 2015 kern.info kernel: [ 27.940000] wlan1: authenticated
Mon May 4 22:36:31 2015 kern.info kernel: [ 27.960000] wlan1: associate with aa:bb:cc:dd:ee:ff (try 1/3)
Mon May 4 22:36:31 2015 kern.info kernel: [ 27.970000] wlan1: RX AssocResp from aa:bb:cc:dd:ee:ff (capab=0x421 status=0 aid=2)
Mon May 4 22:36:31 2015 kern.info kernel: [ 27.980000] wlan1: associated
Mon May 4 22:36:31 2015 kern.info kernel: [ 27.990000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
Mon May 4 22:36:32 2015 kern.info kernel: [ 28.170000] br-lan: port 2(wlan0) entered forwarding state
Mon May 4 22:36:32 2015 kern.info kernel: [ 28.370000] br-lan: port 3(wlan1-1) entered forwarding state
Mon May 4 22:36:32 2015 kern.info kernel: [ 28.370000] br-lan: port 3(wlan1-1) entered forwarding state
Mon May 4 22:36:32 2015 kern.info kernel: [ 28.380000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1-1: link becomes ready
Mon May 4 22:36:34 2015 kern.info kernel: [ 30.370000] br-lan: port 3(wlan1-1) entered forwarding state
Mon May 4 22:38:04 2015 authpriv.info dropbear[1363]: Child connection from 192.168.1.218:50709
Mon May 4 22:38:14 2015 authpriv.notice dropbear[1363]: Password auth succeeded for 'root' from 192.168.1.218:50709
root@OpenWrt:~#
DMESG LOG:
login as: root
root@192.168.1.1's password:
BusyBox v1.22.1 (2014-09-20 22:01:35 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (14.07, r42625)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme de Cacao
-----------------------------------------------------
root@OpenWrt:~# dmesg
[ 0.000000] Linux version 3.10.49 (bb@builder1) (gcc version 4.8.3 (OpenWrt/L inaro GCC 4.8-2014.04 r42625) ) #3 Wed Oct 1 14:00:51 CEST 2014
[ 0.000000] MyLoader: sysp=a52f5067, boardp=4c141c95, parts=9e22f041
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019750 (MIPS 74Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9558 rev 0
[ 0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:200.000MHz, Ref:40.00 0MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 80334b60, node_mem_map 8100000 0
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 32512
[ 0.000000] Kernel command line: board=ARCHER-C7 console=ttyS0,115200 rootfs type=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 126052k/131072k available (2369k kernel code, 5020k reser ved, 621k data, 272k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.060000] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 512
[ 0.070000] NET: Registered protocol family 16
[ 0.070000] MIPS: machine is TP-LINK Archer C7
[ 0.080000] ar724x-pci ar724x-pci.0: PCIe link is down
[ 0.080000] registering PCI controller with io_map_base unset
[ 0.090000] registering PCI controller with io_map_base unset
[ 0.500000] bio: create slab <bio-0> at 0
[ 0.500000] PCI host bridge to bus 0000:00
[ 0.510000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[ 0.510000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.520000] pci_bus 0000:00: No busn resource found for root bus, will use [b us 00-ff]
[ 0.520000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.520000] PCI host bridge to bus 0000:01
[ 0.530000] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
[ 0.530000] pci_bus 0000:01: root bus resource [io 0x0001]
[ 0.540000] pci_bus 0000:01: No busn resource found for root bus, will use [b us 01-ff]
[ 0.540000] pci 0000:01:00.0: [168c:003c] type 00 class 0x028000
[ 0.540000] pci 0000:01:00.0: reg 10: [mem 0x00000000-0x001fffff 64bit]
[ 0.540000] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
[ 0.540000] pci 0000:01:00.0: supports D1 D2
[ 0.540000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.540000] pci 0000:01:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bi t]
[ 0.550000] pci 0000:01:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref ]
[ 0.550000] pci 0000:01:00.0: using irq 41 for pin 1
[ 0.560000] Switching to clocksource MIPS
[ 0.560000] NET: Registered protocol family 2
[ 0.570000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.570000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.570000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.580000] TCP: reno registered
[ 0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.600000] NET: Registered protocol family 1
[ 0.600000] PCI: CLS 0 bytes, default 32
[ 0.610000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.620000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc.
[ 0.630000] msgmni has been set to 246
[ 0.630000] io scheduler noop registered
[ 0.640000] io scheduler deadline registered (default)
[ 0.640000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.670000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.680000] console [ttyS0] enabled, bootconsole disabled
[ 0.690000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.700000] m25p80 spi0.0: found s25fl129p1, expected m25p80
[ 0.700000] m25p80 spi0.0: s25fl129p1 (16384 Kbytes)
[ 0.710000] 5 tp-link partitions found on MTD device spi0.0
[ 0.720000] Creating 5 MTD partitions on "spi0.0":
[ 0.720000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.730000] 0x000000020000-0x00000012e660 : "kernel"
[ 0.730000] mtd: partition "kernel" must either start or end on erase block b oundary or be smaller than an erase block -- forcing read-only
[ 0.750000] 0x00000012e660-0x000000ff0000 : "rootfs"
[ 0.750000] mtd: partition "rootfs" must either start or end on erase block b oundary or be smaller than an erase block -- forcing read-only
[ 0.760000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.770000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.780000] 0x000000390000-0x000000ff0000 : "rootfs_data"
[ 0.780000] 0x000000ff0000-0x000001000000 : "art"
[ 0.790000] 0x000000020000-0x000000ff0000 : "firmware"
[ 0.830000] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[ 2.070000] libphy: ag71xx_mdio: probed
[ 2.620000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd0 34, driver=Atheros AR8216/AR8236/AR8316]
[ 2.640000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 3.190000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII
[ 3.200000] TCP: cubic registered
[ 3.200000] NET: Registered protocol family 17
[ 3.210000] Bridge firewalling registered
[ 3.210000] 8021q: 802.1Q VLAN Support v1.8
[ 3.230000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 3.230000] Freeing unused kernel memory: 272K (8034c000 - 80390000)
[ 5.770000] usbcore: registered new interface driver usbfs
[ 5.780000] usbcore: registered new interface driver hub
[ 5.780000] usbcore: registered new device driver usb
[ 5.790000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.800000] ehci-platform: EHCI generic platform driver
[ 5.800000] ehci-platform ehci-platform.0: EHCI Host Controller
[ 5.810000] ehci-platform ehci-platform.0: new USB bus registered, assigned b us number 1
[ 5.820000] ehci-platform ehci-platform.0: TX-TX IDP fix enabled
[ 5.830000] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[ 5.850000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[ 5.850000] hub 1-0:1.0: USB hub found
[ 5.860000] hub 1-0:1.0: 1 port detected
[ 5.860000] ehci-platform ehci-platform.1: EHCI Host Controller
[ 5.870000] ehci-platform ehci-platform.1: new USB bus registered, assigned b us number 2
[ 5.880000] ehci-platform ehci-platform.1: TX-TX IDP fix enabled
[ 5.880000] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[ 5.910000] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
[ 5.910000] hub 2-0:1.0: USB hub found
[ 5.920000] hub 2-0:1.0: 1 port detected
[ 6.330000] usb 2-1: new high-speed USB device number 2 using ehci-platform
[ 6.370000] eth1: link up (1000Mbps/Full duplex)
[ 9.710000] jffs2: notice: (363) jffs2_build_xattr_subsystem: complete buildi ng xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 15 of xref (0 dead, 1 orphan) found.
[ 9.800000] eth1: link down
[ 11.250000] NET: Registered protocol family 10
[ 11.260000] nf_conntrack version 0.5.0 (1973 buckets, 7892 max)
[ 11.270000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.290000] Loading modules backported from Linux version master-2014-05-22-0 -gf2032ea
[ 11.290000] Backport generated by backports.git backports-20140320-37-g5c33da 0
[ 11.320000] cfg80211: Calling CRDA to update world regulatory domain
[ 11.320000] cfg80211: World regulatory domain updated:
[ 11.330000] cfg80211: DFS Master region: unset
[ 11.330000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai n, max_eirp), (dfs_cac_time)
[ 11.340000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 m Bm), (N/A)
[ 11.350000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 m Bm), (N/A)
[ 11.360000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 m Bm), (N/A)
[ 11.370000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.370000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 11.380000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 11.390000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 m Bm), (N/A)
[ 11.400000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 11.460000] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0x12000000-0x121fff ff 64bit]
[ 11.460000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[ 11.770000] ath10k: pci irq legacy irq_mode 0 reset_mode 0
[ 11.870000] ath10k: otp stream is empty, using board.bin contents
[ 13.010000] ath10k: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.1.467.2-1 ap i 2 htt 2.1
[ 13.550000] ath: EEPROM regdomain: 0x0
[ 13.550000] ath: EEPROM indicates default country code should be used
[ 13.550000] ath: doing EEPROM country->regdmn map search
[ 13.550000] ath: country maps to regdmn code: 0x3a
[ 13.550000] ath: Country alpha2 being used: US
[ 13.550000] ath: Regpair used: 0x3a
[ 13.560000] cfg80211: Calling CRDA for country: US
[ 13.570000] cfg80211: Regulatory domain changed to country: US
[ 13.570000] cfg80211: DFS Master region: FCC
[ 13.580000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai n, max_eirp), (dfs_cac_time)
[ 13.590000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 m Bm), (N/A)
[ 13.590000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 m Bm), (N/A)
[ 13.600000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 m Bm), (0 s)
[ 13.610000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 m Bm), (N/A)
[ 13.620000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 40 00 mBm), (N/A)
[ 13.650000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 13.690000] xt_time: kernel timezone is -0000
[ 13.710000] PPP generic driver version 2.4.2
[ 13.720000] NET: Registered protocol family 24
[ 13.730000] ath: EEPROM regdomain: 0x0
[ 13.730000] ath: EEPROM indicates default country code should be used
[ 13.730000] ath: doing EEPROM country->regdmn map search
[ 13.730000] ath: country maps to regdmn code: 0x3a
[ 13.730000] ath: Country alpha2 being used: US
[ 13.730000] ath: Regpair used: 0x3a
[ 13.740000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 13.750000] ieee80211 phy1: Atheros AR9550 Rev:0 mem=0xb8100000, irq=47
[ 20.670000] eth1: link up (1000Mbps/Full duplex)
[ 20.670000] device eth1 entered promiscuous mode
[ 20.680000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 20.700000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 21.670000] br-lan: port 1(eth1) entered forwarding state
[ 21.670000] br-lan: port 1(eth1) entered forwarding state
[ 21.710000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 21.850000] eth0: link up (1000Mbps/Full duplex)
[ 21.850000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 23.090000] ath10k: otp stream is empty, using board.bin contents
[ 23.670000] br-lan: port 1(eth1) entered forwarding state
[ 23.940000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 23.960000] IPv6: ADDRCONF(NETDEV_UP): wlan1-1: link is not ready
[ 23.970000] device wlan0 entered promiscuous mode
[ 23.980000] device wlan1-1 entered promiscuous mode
[ 26.170000] br-lan: port 2(wlan0) entered forwarding state
[ 26.170000] br-lan: port 2(wlan0) entered forwarding state
[ 26.180000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 27.050000] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 27.920000] wlan1: authenticate with aa:bb:cc:dd:ee:ff
[ 27.930000] wlan1: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[ 27.940000] wlan1: authenticated
[ 27.960000] wlan1: associate with aa:bb:cc:dd:ee:ff (try 1/3)
[ 27.970000] wlan1: RX AssocResp from aa:bb:cc:dd:ee:ff (capab=0x421 status=0 aid=2)
[ 27.980000] wlan1: associated
[ 27.990000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 28.170000] br-lan: port 2(wlan0) entered forwarding state
[ 28.370000] br-lan: port 3(wlan1-1) entered forwarding state
[ 28.370000] br-lan: port 3(wlan1-1) entered forwarding state
[ 28.380000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1-1: link becomes ready
[ 30.370000] br-lan: port 3(wlan1-1) entered forwarding state
root@OpenWrt:~#
My future configuration will be:
- Ubiquiti Nanostation M2 receiving the Zon Fon Signal
(IP: 192.168.1.20 + DHCP activated)
- TP-Link Archer C7 v2 distributing the signal in my own Wireless Lan
(IP: 192.168.1.1 + DHCP deactivated + GW: 192.168.1.20)
So I will need to change WWAN to LAN?
(Last edited by gandamaluko on 5 May 2015, 20:06)