Hi all, this is post to document the Zyxel AMG1302-T10B, I recently had a couple of these donated to me and couldn't find out much about them, less so on OpenWRT.
The ZyXEL AMG1302 is Wireless-N ADSL2+ Router, with two "Airgain" antennas built around a Ralink rt63365e
Using a Serial Converter on J4 on the mother board (RXD, TXD, GND, VCC 3V - 115200) the boot process is as follows;
U-Boot 1.1.5 (Jan 31 2013 - 11:09:29)
CPU: RT63365
Memory Size: 32 MB
Found SPI Flash 8MiB Winbond W25Q64 at 0xb0000000
Size: 8 MB in 128 Sectors
Manufacturer ID = 00ef
Device ID = 4017
Using default environment
In: serial
Out: serial
Err: serial
Net: skbuff start addr a1100000
RT63365 Switch
MAC addresses in MRD and Env don't match.
Use MAC in MRD: 28:28:5D:A5:7E:B4
## Starting application at 0x81FC0000 ...
OK
Search PHY addr and found PHY addr=0
Hit any key to stop autoboot: 0
***** ZyXEL Communications Corporation Firmware *****
Uncompressing [LZMA] ... done.
Linux version 2.6.22.15 (root@seven-desktop) (gcc version 4.3.4 (GCC) ) #17 SMP Thu Jun 20 21:59:36 CST 2013
ISPRAM0: PA=00270000,Size=00008000,enabled
Enable SRAM=1c000001
Ralink RT63365 SOC prom init
CPU revision is: 00019555
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
3 available secondary CPU TC(s)
Built 1 zonelists. Total pages: 8128
Kernel command line: console=ttyS0 rootfstype=squashfs es=1
Primary instruction cache 64kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (23 instructions).
Synthesized TLB load handler fastpath (37 instructions).
Synthesized TLB store handler fastpath (37 instructions).
Synthesized TLB modify handler fastpath (36 instructions).
Cache parity protection disabled
PID hash table entries: 128 (order: 7, 512 bytes)
CPU frequency 420.00 MHz
Using 250.000 MHz high precision timer.
console handover: boot [early0] -> real [ttyS0]
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29044k/32768k available (2404k kernel code, 3724k reserved, 491k data, 168k init, 0k highmem)
SLUB: Genslabs=17, HWalign=32, Order=0-1, MinObjects=4, CPUs=4, Nodes=1
Mount-cache hash table entries: 512
34K sync es set to 1.
Config7: 0x80080500
FPU Affinity set after 929 emulations
Limit of 4 TCs set
TLB of 64 entry pairs shared by 2 VPEs
VPE 0: TC 0 1 2, VPE 1: TC 3
IPI buffer pool of 32 buffers
CPU revision is: 00019555
TC 1 going on-line as CPU 1
CPU revision is: 00019555
TC 2 going on-line as CPU 2
CPU revision is: 00019555
TC 3 going on-line as CPU 3
Brought up 4 CPUs
migration_cost=10000
NET: Registered protocol family 16
RT63365_pcie_init
registering PCI controller with io_map_base unset
PCI: Bridge: 0000:00:00.0
IO window: disabled.
MEM window: 20000000-200fffff
PREFETCH window: disabled.
PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 12288 bytes)
TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
TC3162 hardware watchdog module loaded.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered (default)
ttyS0 at I/O 0xbfbf0003 (irq = 1) is a TC3162
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
IMQ starting with 2 devices...
IMQ driver loaded successfully.
Hooking IMQ after NAT on PREROUTING.
Hooking IMQ before NAT on POSTROUTING.
tc3162: flash device 0x01000000 at 0x10000000
tc3162: Found SPIFLASH 8MiB Winbond W25Q64
Creating 9 MTD partitions on "tc3162":
0x00000000-0x00020000 : "bootloader"
0x00020000-0x00030000 : "romfile"
0x00030000-0x0012b210 : "kernel"
mtd: partition "kernel" doesn't end on an erase block -- force read-only
0x0012b210-0x005d2210 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x005d2210-0x005d4dce : "defcfg"
mtd: partition "defcfg" doesn't start on an erase block boundary -- force read-only
0x00030000-0x007a0000 : "tclinux"
0x007a0000-0x007e0000 : "reservearea"
0x007e0000-0x007f0000 : "romd"
0x007f0000-0x00800000 : "second_romfile"
root filesystem is from rootfs
RT3xxx EHCI/OHCI init.
net/core/klink_updown.c:99 >> Create link_updown kernel netlink success!
u32 classifier
Performance counters on
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (256 buckets, 2048 max)
ctnetlink v0.93: registering with nfnetlink.
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 168k freed
busybox init and set aff
init started: BusyBox v1.00 (2013.06.20-13:59+0000) multi-call binary
chmod: /userfs/profile.cfg: Read-only file system
/userfs/profile.cfg: 329: TRUE_AUTO_DMZ: not found
tcledctrl: module license 'unspecified' taints kernel.
TC3162 LED Manager 0.1 init
tcledctrl version: tcledctrl V1.1.0.0 (Jun 20 2013-21:59:47).
tccicmd V1.1.0.0 (Jun 20 2013-21:59:48)
htp_switch=0
system is initialized in normal mode
tcsmux version: tcsmux V1.1.0.0 (Dec 25 2011-15:32:01).
tcportbind version: tcportbind V1.1.0.0 (Jun 20 2013-20:13:24).
TCSUPPORT_IPV6
write file (/tmp/md5.txt) successfully!
The number of cache node is 5
compressedLen = 13311
===webRedirectInit, reason = 1, redirect status: 0===
can't read web redirect parametercompressedLen = 13062
compressedLen = 13311
Read current configuration...
compressedLen = 11158
Read default configuration...
sslca_verify!
node is NULL
node is NULL
node is NULL
node is NULL
node is NULL
node is NULL
node is NULL
node is NULL
node is NULL
node is NULLFile /etc/isp0.conf content DHCPClientopt60Flag= is worng
File /etc/isp0.conf content DHCPClientopt60value= is worng
etherWan_write isMSTCEtherWan=0 not ETH mode
mrd.CountryCode = FF
Success to set CountryRegion by mrd country code.
mtd[readflash]:device=reservearea tclen=512 tcoffset=196608
Unlocking reservearea ...
Reading from reservearea to /tmp/RT30xxEEPROM.bin ...
firewall_cmd = iptables -t filter -A FIREWALL_INPUT -i br+ -j RETURN
firewall_cmd = ip6tables -t filter -A FIREWALL_INPUT -i br+ -j RETURN
firewall_cmd = iptables -t filter -A FIREWALL_FORWARD -i br+ -j RETURN
firewall_cmd = ip6tables -t filter -A FIREWALL_FORWARD -i br+
Add CWMP pass through rules.ables -t filter -A FIREWALL_FORWARD -i ! br+ -m state --state NEW,INVALID -j DROP
firewall_cmd = ip6tables -t filter -A FIREWALL_FORWARD -i ! br+ -m state --state NEW,INVALID -j DROP
firewall_cmd = iptables -t filter -A FIREWALL_INPUT -i ! br+ -m state --state NEW,INVALID -j DROP
firewall_cmd = ip6tables -t filter -A FIREWALL_INPUT -i ! br+ -m state --state NEW,INVALID -j DROP
Can't open /etc/isp1.conf
Can't open /etc/isp1.conf
Can't open /etc/isp2.conf
Can't open /etc/isp2.conf
Can't open /etc/isp3.conf
Can't open /etc/isp3.conf
Can't open /etc/isp4.conf
Can't open /etc/isp4.conf
Can't open /etc/isp5.conf
Can't open /etc/isp5.conf
Can't open /etc/isp6.conf
Can't open /etc/isp6.conf
Can't open /etc/isp7.conf
Can't open /etc/isp7.conf
Can't open /etc/isp8.conf
Can't open /etc/isp9.conf
Can't open /etc/isp10.conf
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
acl_cmd=iptables -t filter -A acl_chain -i br0 -p TCP -m multiport --dport 80 -m iprange --src-range 0.0.0.0-223.255.255.255 -j ACCEPT
acl_cmd=iptables -t filter -A acl_chain -i br0 -p UDP -m multiport --dport 80 -m iprange --src-range 0.0.0.0-223.255.255.255 -j ACCEPT
acl_cmd=ip6tables -t filter -A acl_chain -i br0 -p TCP -m multiport --dport 80 -j ACCEPT
acl_cmd=ip6tables -t filter -A acl_chain -i br0 -p UDP -m multiport --dport 80 -j ACCEPT
acl_cmd=iptables -t filter -A acl_chain -i br0 -p TCP -m multiport --dport 23 -m iprange --src-range 0.0.0.0-223.255.255.255 -j ACCEPT
acl_cmd=iptables -t filter -A acl_chain -i br0 -p UDP -m multiport --dport 23 -m iprange --src-range 0.0.0.0-223.255.255.255 -j ACCEPT
acl_cmd=ip6tables -t filter -A acl_chain -i br0 -p TCP -m multiport --dport 23 -j ACCEPT
acl_cmd=ip6tables -t filter -A acl_chain -i br0 -p UDP -m multiport --dport 23 -j ACCEPT
acl_cmd=iptables -t filter -A acl_chain -i br0 -p TCP -m multiport --dport 21 -m iprange --src-range 0.0.0.0-223.255.255.255 -j ACCEPT
acl_cmd=iptables -t filter -A acl_chain -i br0 -p UDP -m multiport --dport 21 -m iprange --src-range 0.0.0.0-223.255.255.255 -j ACCEPT
acl_cmd=ip6tables -t filter -A acl_chain -i br0 -p TCP -m multiport --dport 21 -j ACCEPT
acl_cmd=ip6tables -t filter -A acl_chain -i br0 -p UDP -m multiport --dport 21 -j ACCEPT
acl_cmd=iptables -t filter -A acl_chain -i br0 -p TCP -m multiport --dport 161 -m iprange --src-range 0.0.0.0-223.255.255.255 -j ACCEPT
acl_cmd=iptables -t filter -A acl_chain -i br0 -p UDP -m multiport --dport 161 -m iprange --src-range 0.0.0.0-223.255.255.255 -j ACCEPT
acl_cmd=ip6tables -t filter -A acl_chain -i br0 -p TCP -m multiport --dport 161 -j ACCEPT
acl_cmd=ip6tables -t filter -A acl_chain -i br0 -p UDP -m multiport --dport 161 -j ACCEPT
acl_cmd=iptables -t filter -A acl_chain -i br0 -p TCP -m multiport --dport domain -m iprange --src-range 0.0.0.0-223.255.255.255 -j ACCEPT
acl_cmd=iptables -t filter -A acl_chain -i br0 -p UDP -m multiport --dport domain -m iprange --src-range 0.0.0.0-223.255.255.255 -j ACCEPT
acl_cmd=ip6tables -t filter -A acl_chain -i br0 -p TCP -m multiport --dport domain -j ACCEPT
acl_cmd=ip6tables -t filter -A acl_chain -i br0 -p UDP -m multiport --dport domain -j ACCEPT
Error occurs while getting Wan PVC1 Activate value.
Error occurs while getting Wan PVC2 Activate value.
Error occurs while getting Wan PVC3 Activate value.
Error occurs while getting Wan PVC4 Activate value.
Error occurs while getting Wan PVC5 Activate value.
Error occurs while getting Wan PVC6 Activate value.
Error occurs while getting Wan PVC7 Activate value.
The TransMode is ATM SKIP PVC8
The TransMode is ATM SKIP PVC9
The TransMode is ATM SKIP PVC10
acl_cmd=iptables -t filter -A acl_chain -i ppp0 -p ICMP --icmp-type 8 -m iprange --src-range 0.0.0.0-223.255.255.255 -j ACCEPT
acl_cmd=ip6tables -t filter -A acl_chain -i ppp0 -p ICMPv6 --icmpv6-type 128 -j ACCEPT
acl_cmd=iptables -t filter -A acl_chain -i br0 -p ICMP --icmp-type 8 -m iprange --src-range 0.0.0.0-223.255.255.255 -j ACCEPT
acl_cmd=ip6tables -t filter -A acl_chain -i br0 -p ICMPv6 --icmpv6-type 128 -j ACCEPT
acl_cmd=iptables -t filter -A acl_chain -i br0 -p TCP -m multiport --dport 22 -m iprange --src-range 0.0.0.0-223.255.255.255 -j ACCEPT
acl_cmd=iptables -t filter -A acl_chain -i br0 -p UDP -m multiport --dport 22 -m iprange --src-range 0.0.0.0-2
===.webRedirectInit, reason = 1, redirect status: 0===
acl
can't read web redirect parameterport 22 -j ACCEPT
acl_cmd=ip6tables -t filter -A acl_chain -i br0 -p UDP -m multiport --dport 22 -j ACCEPT
acl_cmd=iptables -t filter -A acl_chain -i br0 -p TCP -m multiport --dport 443 -m iprange --src-range 0.0.0.0-223.255.255.255 -j ACCEPT
acl_cmd=iptables -t filter -A acl_chain -i br0 -p UDP -m multiport --dport 443 -m iprange --src-range 0.0.0.0-223.255.255.255 -j ACCEPT
acl_cmd=ip6tables -t filter -A acl_chain -i br0 -p TCP -m multiport --dport 443 -j ACCEPT
acl_cmd=ip6tables -t filter -A acl_chain -i br0 -p UDP -m multiport --dport 443 -j ACCEPT
The kernel doesn't support the ebtables 'filter' table.
sslca_write:get Frag Number failed!
killall: dropbear: no process killed
insmod raeth driver
femac.c:v1.00-NAPI 29.Mar.2011
eth0: FE MAC Ethernet address: 28:28:5D:A5:7E:B4
killall: boa: no process killed
ioctl(SIOCGIFADDR): No such device
TSARM: TC3162 ATM SAR driver 1.5 init
tc3162sar V1.2.0.0 (Jun 20 2013-21:59:45)
register autopvc cmd to sys
TSARM: TC3162 ATM SAR driver 1.5 done
vlantag_drv_init
===webRedirectInit, reason = 1, redirect status: 0===
can't read web redirect parameterADSL mode, insmod tc3162_dmt.ko !
Enabling SSL security system
SSL security system enabled[01/Jan/2010:00:00:06 +0000] boa: server version Boa/0.94.13
[01/Jan/2010:00:00:06 +0000] boa: server built Jun 20 2013 at 22:01:08.
[01/Jan/2010:00:00:06 +0000] boa: starting server pid=168, port 80
ioctl(SIOCGIFADDR): No such device
ADSL DMT initialization starting
Begin AdslTaskInit.....
End AdslTaskInit
Begin to request IRQ 20
DMT:Succeed to request IRQ 20
Initializing ADSL F/W 3.20.36.0 ......
Reset dmt
===webRedirectInit, reason = 1, redirect status: 0===
iptables -t nat -A PREROUTING -i br+ -p tcp --dport 80 -j REDIRECT --to-ports 80
iptables -t nat -A PREROUTING -i br+ -p udp --dport 53 -j DNAT --to 192.168.1.1:53
killall: dnsmasq: no process killed
Check DMT version =b2 ........
Initializing ADSL F/W ........ done
ADSL HW version: b2, HCLK 140
TCSUPPORT_WLAN
TCSUPPORT_WLAN_RT5392
The remaining IMEM space cannot accommodate section .text.imem !!
Remaining IMEM space: -4540 bytes Section Size: 732 bytes
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
Mirror/redirect action on
Ebtables v2.0 registered
igmpsnoop V1.1.0.0 (Oct 23 2012-16:24:33)
mldsnooping V1.1.0.0 (Jun 8 2012-14:28:18)
eth0: starting interface.
alloc_sram p=bc000800 free=7800
alloc_sram p=bc002800 free=5800
TC2105MJ, <6>Ralink HW NAT Module Enabled
device eth0 entered promiscuous mode
TCSUPPORT_WLAN: ifconfig
0x1300 = 00064380
jiffies=ffff91f3, POLLING_MODE_DETECT_INTV=300
device ra0 entered promiscuous mode
0x1300 = 00064380
jiffies=ffff944a, POLLING_MODE_DETECT_INTV=300
device ra1 entered promiscuous mode
0x1300 = 00064380
jiffies=ffff96a1, POLLING_MODE_DETECT_INTV=300
device ra2 entered promiscuous mode
0x1300 = 00064380
jiffies=ffff98f6, POLLING_MODE_DETECT_INTV=300
device ra3 entered promiscuous mode
TCSUPPORT_WLAN_WDS
TC3162 hardware watchdog initialized
telnetd: starting
port: 23; login program: /bin/login
[01/Jan/2010:00:00:36 +0000] boa.c:971 - unable to bind: Address already in use
========================insmod iptable_filter=======================
insmod: cannot open module `/lib/modules/2.6.22.15/kernel/net/ipv4/netfilter/iptable_filter.ko': No such file or directory
iptables: Chain already exists
ip6tables: No chain/target/match by that name
/userfs/profile.cfg: 329: TRUE_AUTO_DMZ: not found
/etc/isp0.conf
/etc/ConcurrentWAN.conf
/usr/script/wan_start.sh: 540: cannot create /proc/sys/net/ipv6/conf/nas0/interface_identifier: Directory nonexistent
iptables v1.3.8: Unknown arg `--set-mss'
Try `iptables -h' or 'iptables --help' for more information.
SIOCDIFADDR: Cannot assign requested address
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
lugin pppoa loaded.
PPPoA Plugin Initialized
Plugin pppoa called.
PPPoATM setdevname_pppoatm - SUCCESS
PPPoATM setdevname_pppoatm - SUCCESS
Options file - /etc/ppp/options.0.38.
setting line discipline hook
connect_pppoatm_ses...Enter
connect_pppoatm_ses: socket created fd - 0xc.
traffic_class = 1
glb.qos.rxtp.traffic_class = 0
glb.qos.txtp.pcr = glb.qos.rxtp.pcr = 0
connect_pppoatm_ses: setsockopt called.
sh: /userfs/bin/dproxy: not found
Open file OK fd=10
warning, Failure parsing line 7 of /etc/udhcpd.conf
warning, Failure parsing line 12 of /etc/udhcpd.conf
info, udhcpd (v0.9.9-pre) started
warning, Failure parsing line 8 of /etc/udhcpd_option.conf
warning, Failure parsing line 18 of /etc/udhcpd_option.conf
warning, Unable to open /etc/udhcp_lease for reading
connect_pppoatm_ses: connect successful.
Calling line discipline hook
Setting pppoatm line discipline.
vc encaps.
Using interface ppp0
Connect: ppp0 <-->
Couldn't increase MTU to 1500
Couldn't increase MRU to 1500
Cannot find device "nas0"
Action 4 device imq0 ifindex 2
Cannot find device "nas0"
ra0 no private iread WLAN driver from rt_device failed,set with default value!
device wds0 is not a slave of br0
device wds1 is not a slave of br0
device wds2 is not a slave of br0
device wds3 is not a slave of br0
killall: wscd: no process killed
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables v1.3.8: log-level `DEBUG--log-prefix' unknown
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name
Testlab 26
ANNEXAIJLM
Enter cwmp boot, we will start tr69 Process
Set SN:S142E12003874 into romfile!
/etc/syslog.conf: 5: WAN-DHCP: not found
/etc/syslog.conf: 6: xDSL: not found
/etc/syslog.conf: 7: ETHER: not found
/etc/syslog.conf: 8: PPP: not found
/etc/syslog.conf: 9: SystemMaintenance: not found
/etc/syslog.conf: 10: RemoteManagement: not found
/etc/syslog.conf: 11: TR069: not found
/etc/syslog.conf: 12: NTP: not found
/etc/syslog.conf: 13: DDNS: not found
/etc/syslog.conf: 14: NAT: not found
/etc/syslog.conf: 15: Firewall: not found
/etc/syslog.conf: 16: DHCP-Srv: not found
/etc/syslog.conf: 17: WLAN: not found
/etc/syslog.conf: 18: INTERNET: not found
/etc/syslog.conf: 19: UPNP: not found
/etc/syslog.conf: 20: DoS: not found
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
ip6tables: No chain/target/match by that name
ip6tables: No chain/target/match by that name
ip6tables: No chain/target/match by that name
ip6tables: No chain/target/match by that name
killall: tftpd: no process killed
rmmod: xt_layer7: No such file or directory
/etc/lanAlias0.conf
ftp switch turn on
sip switch turn off
h323 switch turn on
rtsp switch turn on
l2tp switch turn on
ipsec switch turn on
route: SIOC[ADD|DEL]RT: File exists
email4log:[PrintTime_420]Set the Schedule. Current time 2010/01/01 00:00:44
four ports
SIOCGIFFLAGS: No such device
interface eth0.1 does not exist!
sh: vconfig: not found
SIOCGIFFLAGS: No such device
interface eth0.2 does not exist!
sh: vconfig: not found
SIOCGIFFLAGS: No such device
interface eth0.3 does not exist!
sh: vconfig: not found
ra0 no private ioctls.
SIOCGIFFLAGS: No such device
interface eth0.4 does not exist!
ra0 no private ioctls.
sh: vconfig: not found
ra0 no private ioctls.
SIOCGIFFLAGS: No such device
==>getMacEntryByIndex(): ioctl open fail
==>getMacEntryByIndex(): ioctl open fail
==>getMacEntryByIndex(): ioctl open fail
interface eth0.5 does not exist!
==>getMacEntryByIndex(): ioctl open fail
sh: vconfig: not found
SIOCGIFFLAGS: No such device
interface eth0.6 does not exist!
sh: vconfig: not found
device eth0 is already a member of a bridge; can't enslave it to bridge br0.
/usr/etc/init.d/rcS: 17: cannot create /proc/tc3162/stag_to_vtag: Directory nonexistent
Added VLAN with VID == 1 to IF -:eth0:-
WARNING: VLAN 1 does not work with many switches,
consider another number if you have problems.
br0: port 6(eth0.1) entering learning state
br0: topology change detected, propagating
br0: port 6(eth0.1) entering forwarding state
Added VLAN with VID == 2 to IF -:eth0:-
br0: port 7(eth0.2) entering learning state
br0: topology change detected, propagating
br0: port 7(eth0.2) entering forwarding state
Added VLAN with VID == 3 to IF -:eth0:-
br0: port 8(eth0.3) entering learning state
br0: topology change detected, propagating
br0: port 8(eth0.3) entering forwarding state
Added VLAN with VID == 4 to IF -:eth0:-
br0: port 9(eth0.4) entering learning state
br0: topology change detected, propagating
br0: port 9(eth0.4) entering forwarding state
Added VLAN with VID == 5 to IF -:eth0:-
br0: port 10(eth0.5) entering learning state
br0: topology change detected, propagating
br0: port 10(eth0.5) entering forwarding state
process `snmpd' is using deprecated sysctl (syscall) net.ipv6.neigh.lo.retrans_time; Use net.ipv6.neigh.lo.retrans_time_ms instead.
get value error(normal attr),the attrName is ISP
get value error(normal attr),the attrName is ISP
get value error(normal attr),the attrName is ISP
get value error(normal attr),the attrName is ISP
get value error(normal attr),the attrName is ISP
get value error(normal attr),the attrName is ISP
get value error(normal attr),the attrName is ISPed VLAN with VID == 6 to IF -:eth0:-
<7>eth0.6: add 33:33:00:00:00:01 mcast address to master interface
AddTimer: get now_time for first time
br0: port 11(eth0.6) entering learning state
br0: topology change detected, propagating
br0: port 11(eth0.6) entering forwarding state
device eth0 left promiscuous mode
br0: port 1(eth0) entering disabled state
eth0.1: dev_set_promiscuity(master, 1)
device eth0 entered promiscuous mode
largeD flag=2 (0:maxD=64, 1:maxD=128, 2:maxD=511)
eth0.3: dev_set_promiscuity(master, 1)
ra0 no private ioctls.
FwVer:3.20.36.0_A_TC3087 HwVer:T14.F7_11.2
xDSL module is OK
WIFI module is FAILED
ETH0 interface is OK
eth0.5: dev_set_promiscuity(master, 1)
eth0.2: dev_set_promiscuity(master, 1)
RA0 interface is FAILED
BR0 interface is OK
APP tcapi is OK
<<< Device failed during initializing >>>
Please press Enter to activate this console. eth0.4: dev_set_promiscuity(master, 1)
eth0.6: dev_set_promiscuity(master, 1)
ThreadedTimerCheck: get last for first time
ZyXEL login:
A binwalk of a firmware contains the following;
Scan Time: 2015-05-18 11:36:16
Signatures: 193
Target File: V2.00(AAFN.9)C0.bin
MD5 Checksum: 9480b9395a3eb405c5a7bdfb131d86a3
DECIMAL HEX DESCRIPTION
-------------------------------------------------------------------------------------------------------
512 0x200 LZMA compressed data, properties: 0x5D, dictionary size: 8388608 bytes, uncompressed size: 3177316 bytes
1032381 0xFC0BD Squashfs filesystem, big endian, version 3.0, size: 5030439 bytes, 1139 inodes, blocksize: 65536 bytes, created: Thu Jan 15 12:41:42 2015
I hope some one will find this information useful 
- rsrd.
(Last edited by rsrd on 18 May 2015, 11:36)
