OpenWrt Forum Archive

Topic: Sitecom WLR-7100

The content of this topic has been archived on 30 Jan 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

I've got a WLR-7100, and I thought I would help the community by getting the bootlogs for this device. Unfortunately it won't allow me to boot with the serial port connected. But if I disconnect the port before boot and reconnect it after I powered the router it gives me a partial bootlog. I hope this is enough.

If I boot with the cable connected it returns this information:

U-Boot 2.0.0 (May 22 2013 - 13:25:23)
Board:MI124

sri
Wasp 1.1
wasp_ddr_initial_config(276): Wasp (16bit) ddr1 init
wasp_ddr_initial_config(426): Wasp ddr init done
DRAM: 4 MB
Top of RAM usable for U-Boot at: 80400000
Reserving 236k for U-Boot at: 803c4000
Reserving 192k for malloc() at: 80394000
Reserving 44 Bytes for Board Info at: 80393fd4
Reserving 36 Bytes for Global Data at: 80393fb0
Reserving 128k for boot params() at: 80373fb0
Stack Pointer at: 80373f98

The partial bootlog:

ag934x_enet_initialize...
No valid address in Flash. Using fixed address
 wasp  reset mask:c03300
WASP  ----> S17 PHY *
: cfg1 0xf cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
    3     2     1     0

3: System Boot system code via Flash.
## Booting image at 9f040000 ...
   Image Name:   Linux Kernel Image
   Created:      2014-10-15   4:15:19 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1835780 Bytes =  1.8 MB
   Load Address: 80002000
   Entry Point:  80006110
   Verifying Checksum at 0x9f040040 ...OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80006110) ...
## Giving linux memsize in bytes, 67108864

Starting kernel ...

Booting Atheros AR934x

 init started: BusyBox v1.7.5 (2014-10-15 12:11:05 CST)

starting pid 809, tty '/dev/console': '/sbin/config_init'
mknod: /dev/ttyS0: File exists
mknod: /dev/ttyS1: File exists
Config Init version: 1.7.3.8 date: 2014/10/15
Wed Jan  1 00:00:00 UTC 2014
ln: /lib/./modules: File exists
insmod: can't open '/lib/ar8327_drv.ko': No such file or directory

starting pid 864, tty '/dev/ttyS0': '/sbin/config_term'
************************************************************************
*                                 WLR-7100                             *
************************************************************************

KernelApp/Ramdisk Ver:1.7.3.8                    Date:2014/10/15
password:

Printenv

ar7240> printev   nv

bootdelay=4
baudrate=115200
ethaddr="64:D1:A3:26:9F:0C"
sn=14C222661
hw_ver=1.0.0
hw_id=02261055
pro_id=000
country=000
domain=1
op_mode=0
wanaddr=64:D1:A3:26:9F:0E
wlanaddr=00:AA:BB:CC:DD:12
snextra=14C222661***********
bootfile=uImage
dir=
bc=mi124_f1e
lu=tftp 0x80060000 ${dir}u-boot.bin&&erase 0x9f000000 +$filesize;cp.b
$fileaddr 0x9f000000 $filesize
lf=tftp 0x80060000 ${dir}${bc}-jffs2&&erase 0x9f050000 +$filesize;cp.b
$fileaddr 0x9f050000 $filesize
lk=tftp 0x80060000 ${dir}vmlinux_${bc}.lzma.uImage&&erase 0x9f300000
+$filesize;cp.b $fileaddr 0x9f300000 $filesize
ethact=eth0
bootargs=console=ttyS0,115200 root=31:03 rootfstype=jffs2
init=/sbin/init
mtdparts=ath-nor0:192k(u-boot),64k(u-boot-env),896k(uImage),6912k(rootfs),64k(NVRAM),64k(ART)
ipaddr=192.168.99.9
serverip=192.168.99.8
uboot_ver=2.0.0.3
stdin=serial
stdout=serial
stderr=serial

Environment size: 855/65532 bytes

What extra information is necessary to get OpenWRT support for this device?

(Last edited by ErwinH on 24 Jun 2015, 19:53)

Today I tried the run the uImage's both from BB and CC (ar71xx), but both won't boot.

## Booting image at 80800000 ...
   Image Name:   MIPS OpenWrt Linux-3.18.14
   Created:      2015-06-09  21:39:15 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1192789 Bytes =  1.1 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum at 0x80800040 ...OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 67108864

Starting kernel ...

[    0.000000] Linux version 3.18.14 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45872) ) #1 Sun Jun 7 16:22:32 CEST 2015
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9342 rev 1
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  console=ttyS0,115200 root=31:03 rootfstype=jffs2 init=/sbin/init mtdparts=ath-nor0:192k(u-boot),64k(u-boot-env),896k(uImage),6912k(rootfs),64k(NVRAM),64k(ART) mem=64M rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 60812K/65536K available (2627K kernel code, 131K rwdata, 544K rodata, 208K init, 194K bss, 4724K reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.100000] NET: Registered protocol family 16
[    0.100000] MIPS: machine is Generic AR71XX/AR724X/AR913X based board
[    0.110000] Switched to clocksource MIPS
[    0.120000] NET: Registered protocol family 2
[    0.120000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.120000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.130000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.130000] TCP: reno registered
[    0.140000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.140000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.150000] NET: Registered protocol family 1
[    0.150000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.180000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.180000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.190000] msgmni has been set to 118
[    0.210000] io scheduler noop registered
[    0.210000] io scheduler deadline registered (default)
[    0.220000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.220000] console [ttyS0] disabled
[    0.250000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[    0.260000] console [ttyS0] enabled
[    0.260000] console [ttyS0] enabled
[    0.260000] bootconsole [early0] disabled
[    0.260000] bootconsole [early0] disabled
[    0.280000] TCP: cubic registered
[    0.280000] NET: Registered protocol family 17
[    0.280000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.300000] Bridge firewalling registered
[    0.300000] 8021q: 802.1Q VLAN Support v1.8
[    0.320000] VFS: Cannot open root device "31:03" or unknown-block(31,3): error -6
[    0.330000] Please append a correct "root=" boot option; here are the available partitions:
[    0.340000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,3)
[    0.340000] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,3)

Now I have to find the next steps.

More progress. I've booted the AP135-020 initramfs image. Network and Wireless gets detected.

[    0.000000] Linux version 3.10.49 (erwin@ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45951) ) #6 Sat Jun 27 19:34:37 CEST 2015
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9342 rev 1
[    0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=AP135-020 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,14528k(rootfs),1472k(kernel),64k(art)ro,16000k@0x50000(firmware) rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 59288k/65536k available (2239k kernel code, 6248k reserved, 603k data, 2212k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] MIPS: machine is Atheros AP135-020 reference board
[    0.300000] ar71xx: invalid PHY interface mode for GE1
[    0.310000] registering PCI controller with io_map_base unset
[    0.320000] bio: create slab <bio-0> at 0
[    0.330000] PCI host bridge to bus 0000:00
[    0.330000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    0.340000] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.340000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.350000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
[    0.350000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref]
[    0.360000] pci 0000:00:00.0: using irq 40 for pin 1
[    0.360000] Switching to clocksource MIPS
[    0.370000] NET: Registered protocol family 2
[    0.370000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.370000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.380000] TCP: Hash tables configured (established 512 bind 512)
[    0.380000] TCP: reno registered
[    0.390000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.400000] NET: Registered protocol family 1
[    3.040000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    3.050000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    3.060000] msgmni has been set to 115
[    3.060000] io scheduler noop registered
[    3.070000] io scheduler deadline registered (default)
[    3.070000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    3.100000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    3.110000] console [ttyS0] enabled, bootconsole disabled
[    3.110000] console [ttyS0] enabled, bootconsole disabled
[    3.120000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[    3.130000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[    3.130000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[    3.140000] mtd: spi0.0: partitioning exceeds flash size, truncating
[    3.150000] mtd: spi0.0: partitioning exceeds flash size, truncating
[    3.150000] mtd: spi0.0: skipping zero sized partition
[    3.160000] mtd: spi0.0: partitioning exceeds flash size, truncating
[    3.160000] mtd: spi0.0: skipping zero sized partition
[    3.170000] mtd: spi0.0: partitioning exceeds flash size, truncating
[    3.180000] 4 cmdlinepart partitions found on MTD device spi0.0
[    3.180000] Creating 4 MTD partitions on "spi0.0":
[    3.190000] 0x000000000000-0x000000040000 : "u-boot"
[    3.190000] 0x000000040000-0x000000050000 : "u-boot-env"
[    3.200000] 0x000000050000-0x000000800000 : "rootfs"
[    3.210000] mtd: device 2 (rootfs) set to be root filesystem
[    3.210000] mtdsplit: no squashfs found in "rootfs"
[    3.220000] mtdsplit: no squashfs found in "spi0.0"
[    3.230000] 0x000000050000-0x000000800000 : "firmware"
[    3.260000] switch0: Atheros AR8337 rev. 2 switch registered on ag71xx-mdio.0
[    4.460000] libphy: ag71xx_mdio: probed
[    5.010000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[    5.030000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    5.040000] TCP: cubic registered
[    5.040000] NET: Registered protocol family 17
[    5.040000] 8021q: 802.1Q VLAN Support v1.8
[    5.060000] Freeing unused kernel memory: 2212K (80327000 - 80550000)
procd: Console is alive
procd: - watchdog -
[    5.110000] usbcore: registered new interface driver usbfs
[    5.110000] usbcore: registered new interface driver hub
[    5.120000] usbcore: registered new device driver usb
[    5.130000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.140000] ehci-platform: EHCI generic platform driver
[    5.140000] ehci-platform ehci-platform: EHCI Host Controller
[    5.150000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    5.160000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    5.190000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    5.190000] hub 1-0:1.0: USB hub found
[    5.200000] hub 1-0:1.0: 1 port detected
[    5.200000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
procd: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[    9.690000] NET: Registered protocol family 10
[    9.700000] nf_conntrack version 0.5.0 (960 buckets, 3840 max)
[    9.710000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    9.730000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[    9.740000] Backport generated by backports.git backports-20140320-37-g5c33da0
[    9.770000] cfg80211: Calling CRDA to update world regulatory domain
[    9.770000] cfg80211: World regulatory domain updated:
[    9.780000] cfg80211:  DFS Master region: unset
[    9.780000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[    9.790000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[    9.800000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[    9.810000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[    9.820000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[    9.830000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[    9.830000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[    9.840000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[    9.850000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[    9.930000] ath10k_pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
[    9.940000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   10.250000] ath10k: pci irq legacy irq_mode 0 reset_mode 0
[   10.340000] ath10k: otp stream is empty, using board.bin contents
[   11.170000] ath10k: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.1.467.2-1 api 2 htt 2.1
[   11.710000] cfg80211: Calling CRDA for country: US
[   11.720000] cfg80211: Regulatory domain changed to country: US
[   11.720000] cfg80211:  DFS Master region: FCC
[   11.730000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   11.740000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[   11.740000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
[   11.750000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[   11.760000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[   11.770000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[   11.810000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.880000] xt_time: kernel timezone is -0000
[   11.910000] PPP generic driver version 2.4.2
[   11.940000] NET: Registered protocol family 24
[   11.980000] ieee80211 phy1: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
procd: - init complete -
[   19.500000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   21.010000] eth0: link up (1000Mbps/Full duplex)
[   21.030000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready



BusyBox v1.22.1 (2015-06-26 11:59:06 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 BARRIER BREAKER (Barrier Breaker, r45951)
 -----------------------------------------------------
  * 1/2 oz Galliano         Pour all ingredients into
  * 4 oz cold Coffee        an irish coffee mug filled
  * 1 1/2 oz Dark Rum       with crushed ice. Stir.
  * 2 tsp. Creme de Cacao
 -----------------------------------------------------
root@OpenWrt:/# 

Next step is to create the profile for this device.

I'm in the progress of building an image for this device. The image itself is working fine, but I have some troubles creating an image which can be flashed.

One of the issues I'm facing is the fact that the uImage-partition is only: 896k(uImage), but when I run make the uImage is 1054473 bytes big which is well over 896k.

When I change the mtdpartitions in the config to 1088k I get a sysupgrade image. Can I flash that (with MTD) without any issues, or will I brick my device doing so?

Made some progress. Booted the initramfs image, with working switch. Flashed with mtd -r write sysupgrade.bin and got a booting router.

[    0.000000] Linux version 3.10.49 (erwin@ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45951) ) #1 Fri Jul 3 10:06:40 CEST 2015
[    0.000000] MyLoader: sysp=c095e295, boardp=26b4ea94, parts=aaa6a084
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9342 rev 1
[    0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 8030e9b0, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=WLR7100 console=ttyS0,115200 mtdparts=spi0.0:192k(u-boot)ro,64k(u-boot-env)ro,1088k(kernel),6720k(rootfs),64k(nvram)ro,64k(art)ro,7808k@0x40000(firmware) rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61272k/65536k available (2232k kernel code, 4264k reserved, 602k data, 236k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.070000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] MIPS: machine is Sitecom WLR-7100
[    0.100000] ar71xx: using random MAC address for eth0
[    0.310000] bio: create slab <bio-0> at 0
[    0.320000] Switching to clocksource MIPS
[    0.330000] NET: Registered protocol family 2
[    0.330000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.330000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.340000] TCP: Hash tables configured (established 512 bind 512)
[    0.340000] TCP: reno registered
[    0.350000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.350000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.360000] NET: Registered protocol family 1
[    0.360000] PCI: CLS 0 bytes, default 32
[    0.380000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.380000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.390000] msgmni has been set to 119
[    0.400000] io scheduler noop registered
[    0.400000] io scheduler deadline registered (default)
[    0.410000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.440000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.440000] console [ttyS0] enabled, bootconsole disabled
[    0.450000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[    0.460000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[    0.470000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[    0.470000] 7 cmdlinepart partitions found on MTD device spi0.0
[    0.480000] Creating 7 MTD partitions on "spi0.0":
[    0.490000] 0x000000000000-0x000000030000 : "u-boot"
[    0.490000] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.500000] 0x000000040000-0x000000150000 : "kernel"
[    0.510000] 0x000000150000-0x0000007e0000 : "rootfs"
[    0.510000] mtd: device 3 (rootfs) set to be root filesystem
[    0.520000] 1 squashfs-split partitions found on MTD device rootfs
[    0.530000] 0x000000330000-0x0000007e0000 : "rootfs_data"
[    0.530000] 0x0000007e0000-0x0000007f0000 : "nvram"
[    0.540000] 0x0000007f0000-0x000000800000 : "art"
[    0.550000] 0x000000040000-0x0000007e0000 : "firmware"
[    0.570000] libphy: ag71xx_mdio: probed
[    0.600000] switch0: Atheros AR8337 rev. 2 switch registered on ag71xx-mdio.0
[    1.800000] libphy: ag71xx_mdio: probed
[    2.350000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[    2.360000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    2.370000] TCP: cubic registered
[    2.380000] NET: Registered protocol family 17
[    2.380000] 8021q: 802.1Q VLAN Support v1.8
[    2.400000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    2.400000] Freeing unused kernel memory: 236K (80325000 - 80360000)
[    4.790000] usbcore: registered new interface driver usbfs
[    4.790000] usbcore: registered new interface driver hub
[    4.800000] usbcore: registered new device driver usb
[    4.810000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.820000] ehci-platform: EHCI generic platform driver
[    4.820000] ehci-platform ehci-platform: EHCI Host Controller
[    4.830000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    4.840000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    4.870000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    4.870000] hub 1-0:1.0: USB hub found
[    4.880000] hub 1-0:1.0: 1 port detected
[    4.880000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    8.720000] jffs2: notice: (346) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 14 of xref (0 dead, 2 orphan) found.
[   10.330000] NET: Registered protocol family 10
[   10.350000] nf_conntrack version 0.5.0 (961 buckets, 3844 max)
[   10.360000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   10.380000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[   10.380000] Backport generated by backports.git backports-20140320-37-g5c33da0
[   10.430000] cfg80211: Calling CRDA to update world regulatory domain
[   10.430000] cfg80211: World regulatory domain updated:
[   10.440000] cfg80211:  DFS Master region: unset
[   10.440000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   10.450000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   10.460000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   10.470000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   10.480000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[   10.490000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   10.490000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   10.500000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   10.510000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   10.580000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.640000] xt_time: kernel timezone is -0000
[   10.650000] PPP generic driver version 2.4.2
[   10.660000] NET: Registered protocol family 24
[   18.800000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   18.810000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[   18.810000] device eth0.1 entered promiscuous mode
[   18.820000] device eth0 entered promiscuous mode
[   18.830000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   18.870000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   20.590000] eth0: link up (1000Mbps/Full duplex)
[   20.600000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   20.610000] br-lan: port 1(eth0.1) entered forwarding state
[   20.610000] br-lan: port 1(eth0.1) entered forwarding state
[   20.620000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[   20.620000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   20.640000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   22.610000] br-lan: port 1(eth0.1) entered forwarding state

Now I need to get the wifi-adapters working again.

(Last edited by ErwinH on 3 Jul 2015, 18:50)

and you made progress
i have bought also a sitecom wlr 7100 and want to install opnwrt on it if its possible...

are you happy about the router his performance ?

grtz

The discussion might have continued from here.