On this page:
http://wiki.openwrt.org/doc/hardware/soc/soc.lantiq?s[]=7360
there is a link to this page:
http://wiki.openwrt.org/toh/avm/fritz.box.wlan.7360

Is the 7360 deleted? Or just waiting to be created?

I have a defective one, it is still owned by the ISP so I'm not sure if it is a good idea to have a look inside.
Though I have practically all info of the chips that are used in this box.

Fritz!box Fon WLAN (VDSL2/ ADSL2, 2+ and DECT)

Power usage: 12V, 1.4A

SDRAM:
Winbond
W971GGJB-25
62265N500022
238ZV0 CHN
----------------
http://www.alldatasheet.net/datasheet-p … GG6JB.html
Winbond 1Gbits DDR2 SDRAM,

CPU:
Lantiq
VRX288
XWAYtm V1.2
------------------
https://wikidevi.com/wiki/Lantiq#VRX_200

FLASH ROM:
MXIC S123796
MX29GL128FHT2I-90G
BAD13300
---------------------
https://media.digikey.com/pdf/Data%20Sh … GL128F.pdf
Macronix 128M (16M x 8)  FLASH - NOR

De Flash layout:

mtd1      0x90020000,0x90F80000   (kernel/fs image)
mtd2      0x90000000,0x90020000   (ADAM2 bootstrap loader)
mtd3      0x90F80000,0x90FC0000   (TTFS configuratie, copie 1)
mtd4      0x90FC0000,0x91000000   (TTFS configuratie, copie 2)

http://gjppp.home.xs4all.nl/vdsl-pppoe/

DSL:
Lantiq
PSB 80190 V
V1.1
XWAYtm VRX208
UMSYGM300
H1209
--------------
https://wikidevi.com/wiki/Lantiq#VRX_200

DECT section:
Analog Data Access Arrangement (DAA):
32228
1238
S49

and:

DAA:
IA3223A
1227CRF014
---------------------
https://www.silabs.com/products/modems/ … ogDAA.aspx

DECT?:
S U1241
SC14441
B52RTL
W1T814.00

WiFi:
Atheros
AR928 -BL1A
PKN390 00B
1229
TAIWAN
--------
http://www.qca.qualcomm.com/wp-content/ … AR9285.pdf (?)

POWER?:
TPS
65252
TIG22A1
ACE9 G4

LAN: (2x)
ATHEROS
AR8030-A
SJTA2.4D
1237 CN
---------------
http://www.qca.qualcomm.com/wp-content/ … AR8030.pdf
https://wikidevi.com/files/Atheros/spec … AR8030.pdf

PHY: (2x)
LFE8505
DELTA
1241

PHY: (2x)
DELTA
LFE9120-R 1231

UART:

1= +3.3V square PAD, Do Not Connect
2= RXin
3= TXout
4= GND

115200 baud

OEM Firmware

    ftp://ftp.avm.de/fritz.box/fritzbox.fon … e/english/ (image)
    ftp://ftp.avm.de/fritz.box/fritzbox.fon … c/english/ (recovery)

Just waiting to be created.

BTW: There is some work going on:
https://www.mail-archive.com/openwrt-de … 39397.html

https://wiki.openwrt.org/toh/avm/fritz.box.wlan.7360

Im also currently on it
I imported the 2 devel-patches from Sebastion for 7360SL and build and flashed the image.

As far i can tell:

• The Gigabit Ethernet ports does not work atm (eth0 and eth1) The Box is reachable via eth2, eth3

• lantiq_vr9_annex_firmware is not selected by default

• phone and dect not working (missing firmware, capi_codec)

• Some AVM drivers should and could be ported

• AVM uses self written binaries to get the MACs out from the TFFS and assign them to interfaces

(Last edited by lipkegu on 2 Jun 2016, 05:34)

VDSL and ADSL (depends on which driver and firmware you had selected) works also:

(Last edited by lipkegu on 3 Jun 2016, 15:25)

I'm curious getting my hands on a spare 7360 to try this out If this works fine, I would have two boxes in production to flash.

Does it work only with the 7360SL or also with the 7360 and 7362SL?

For the phone: Since the VRX288 is a successor to the Danube, maybe the danube-voip package (https://github.com/olivluca/danube-voip) or the Asterisk chan-lantiq works out of the box or with small changes?
But DECT will be much harder, I think.

someone guides me in the programming of these teams (gl.inet 6416), I've only worked with raspberry in atm and want to try this computer

Hi!

Do anyone has hi-res photo of xDSL section of 7360?
I'm looking for both - top and bottom PCB.
It would be the best to make them with international version (Annex A and B)

Best regards

Does this suit your needs?
http://www.wehavemorefun.de/fritzbox/7360#Galerie

Hi!
Bad focus and angle unfortunately.
Beside, this looks like DE version, for only Annex B.

I found information, that int version support both annex and
i'm curious how did they did it

For that purpose accurate photos showing component placement
would be needed

Best regards!

Hi,

i had tried to compilie an Image for the Fritzbox 7360 with the latest Trunk Version of OpenWrt, but i only got these Images. The Box is for my Multiwan Project with DSL and LTE. I had testet it with an Raspberry Pi3 and it works fine. Now is the Idea to get it work an the Box and reduce the Hardware.

openwrt-lantiq-xrx200-ARV7519RW22-squashfs-sysupgrade.bin
openwrt-lantiq-xrx200-EASY80920NAND-squashfs-fullimage.img
openwrt-lantiq-xrx200-EASY80920NAND-squashfs-sysupgrade.bin
openwrt-lantiq-xrx200-EASY80920NOR-squashfs-sysupgrade.bin
openwrt-lantiq-xrx200-TDW8970-squashfs-sysupgrade.bin
openwrt-lantiq-xrx200-TDW8980-squashfs-sysupgrade.bin
openwrt-lantiq-xrx200-VGV7510KW22BRN-squashfs-factory.bin
openwrt-lantiq-xrx200-VGV7510KW22NOR-squashfs-sysupgrade.bin
openwrt-lantiq-xrx200-VGV7519BRN-squashfs-factory.bin
openwrt-lantiq-xrx200-VGV7519NOR-squashfs-sysupgrade.bin
openwrt-lantiq-xrx200-VR200v-squashfs-sysupgrade.bin
openwrt-lantiq-xrx200-WBMR300-squashfs-sysupgrade.bin

does one of this work with the Box, or must i apply the two patches to compilie a extra Image for the Fritzbox?

Thanks for Help

Greetz
Thomas

Maybe can anybody who get an Image working on the Box send me an Image per Mail.