OpenWrt Forum Archive

Topic: comfast CF-E214N

The content of this topic has been archived on 3 May 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

Hi , I have comfast CF-E214N. I think that it is a clone of some other device. I need to flash Openwrt, buth I don't know what version?

This is hardware info:

root@CF-E214N:~# cat /proc/cpuinfo
system type             : Atheros AR7240 rev 2
machine                 : Ubiquiti Nanostation M
processor               : 0
cpu model               : MIPS 24Kc V7.4
BogoMIPS                : 259.27
wait instruction        : yes
microsecond timers      : yes
tlb_entries             : 16
extra interrupt vector  : yes
hardware watchpoint     : yes, count: 4, address/irw mask: [0x0000, 0x0ff8, 0x0f                                                                             f8, 0x0ff8]
ASEs implemented        : mips16
shadow register sets    : 1
kscratch registers      : 0
core                    : 0
VCED exceptions         : not available
VCEI exceptions         : not available

---------------------------------------------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------------------------------------------------------

root@CF-E214N:~# dmesg
[    0.000000] Linux version 3.3.8 (tuodajie@tuodajie-ThinkPad-T410) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #13 Fri Jun 13 12:23:48 CST 2014
[    0.000000] MyLoader: sysp=423e41db, boardp=be54cac9, parts=403e41db
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR7240 rev 2
[    0.000000] Clocks: CPU:390.000MHz, DDR:390.000MHz, AHB:195.000MHz, Ref:5.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00002000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00002000
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 802e50b0, node_mem_map 81000000
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8128 pages, LIFO batch:0
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=UBNT-NM console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,1024k(kernel),6528k(rootfs),256k(cfg)ro,64k(EEPROM)ro,7552k@0x50000(firmware) rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 29048k/32768k available (2169k kernel code, 3720k reserved, 412k data, 212k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 259.27 BogoMIPS (lpj=1296384)
[    0.070000] pid_max: default: 32768 minimum: 301
[    0.070000] Mount-cache hash table entries: 512
[    0.080000] NET: Registered protocol family 16
[    0.080000] gpiochip_add: registered GPIOs 0 to 17 on device: ath79
[    0.090000] MIPS: machine is Ubiquiti Nanostation M
[    0.090000] registering PCI controller with io_map_base unset
[    0.500000] bio: create slab <bio-0> at 0
[    0.510000] PCI host bridge to bus 0000:00
[    0.510000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    0.520000] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.520000] pci 0000:00:00.0: [168c:002b] type 0 class 0x000280
[    0.520000] pci 0000:00:00.0: fixup device configuration
[    0.530000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0000ffff 64bit]
[    0.530000] pci 0000:00:00.0: supports D1
[    0.530000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    0.530000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
[    0.530000] pci 0000:00:00.0: using irq 40 for pin 1
[    0.540000] Switching to clocksource MIPS
[    0.540000] NET: Registered protocol family 2
[    0.550000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.550000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.560000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.560000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.570000] TCP reno registered
[    0.570000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.580000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.590000] NET: Registered protocol family 1
[    0.590000] PCI: CLS 0 bytes, default 32
[    0.610000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.620000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.630000] msgmni has been set to 56
[    0.630000] io scheduler noop registered
[    0.630000] io scheduler deadline registered (default)
[    0.640000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.670000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.670000] console [ttyS0] enabled, bootconsole disabled
[    0.690000] m25p80 spi0.0: found s25fl064k, expected m25p80
[    0.690000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[    0.700000] 7 cmdlinepart partitions found on MTD device spi0.0
[    0.700000] Creating 7 MTD partitions on "spi0.0":
[    0.710000] 0x000000000000-0x000000040000 : "u-boot"
[    0.720000] 0x000000040000-0x000000050000 : "u-boot-env"
[    0.720000] 0x000000050000-0x000000150000 : "kernel"
[    0.730000] 0x000000150000-0x0000007b0000 : "rootfs"
[    0.740000] mtd: partition "rootfs" set to be root filesystem
[    0.740000] mtd: partition "rootfs_data" created automatically, ofs=3D0000, len=3E0000
[    0.750000] 0x0000003d0000-0x0000007b0000 : "rootfs_data"
[    0.760000] 0x0000007b0000-0x0000007f0000 : "cfg"
[    0.770000] 0x0000007f0000-0x000000800000 : "EEPROM"
[    0.770000] 0x000000050000-0x0000007b0000 : "firmware"
[    0.800000] ag71xx_mdio: probed
[    0.800000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.380000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:04 [uid=004dd041, driver=Generic PHY]
[    1.390000] eth1: Atheros AG71xx at 0xba000000, irq 5
[    1.960000] eth1: Found an AR7240/AR9330 built-in switch
[    2.990000] TCP cubic registered
[    2.990000] NET: Registered protocol family 17
[    2.990000] Bridge firewalling registered
[    3.000000] Ebtables v2.0 registered
[    3.000000] 8021q: 802.1Q VLAN Support v1.8
[    3.010000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    3.020000] Freeing unused kernel memory: 212k freed
[    7.390000] eth0: link up (100Mbps/Full duplex)
[    8.580000] JFFS2 notice: (400) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 123 of xref (0 dead, 107 orphan) found.
[    8.790000] eth0: link down
[    9.810000] Compat-drivers backport release: compat-drivers-2013-01-21-1
[    9.820000] Backport based on wireless-testing.git master-2013-02-22
[    9.830000] compat.git: wireless-testing.git
[   10.000000] cfg80211: Calling CRDA to update world regulatory domain
[   10.000000] cfg80211: World regulatory domain updated:
[   10.010000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.020000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.030000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   10.030000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   10.040000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.050000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.590000] usbcore: registered new interface driver usbfs
[   10.590000] usbcore: registered new interface driver hub
[   10.600000] usbcore: registered new device driver usb
[   11.240000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   11.260000] ath: EEPROM regdomain: 0x0
[   11.260000] ath: EEPROM indicates default country code should be used
[   11.260000] ath: doing EEPROM country->regdmn map search
[   11.260000] ath: country maps to regdmn code: 0x3a
[   11.260000] ath: Country alpha2 being used: US
[   11.260000] ath: Regpair used: 0x3a
[   11.260000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   11.270000] Registered led device: ath9k-phy0
[   11.270000] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xb0000000, irq=40
[   11.410000] PPP generic driver version 2.4.2
[   11.430000] cfg80211: Calling CRDA for country: US
[   11.430000] cfg80211: Regulatory domain changed to country: US
[   11.440000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   11.450000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2300 mBm)
[   11.450000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   11.460000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   11.470000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   11.480000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   11.480000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   11.620000] tun: Universal TUN/TAP device driver, 1.6
[   11.630000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   11.740000] GRE over IPv4 demultiplexor driver
[   11.760000] GRE over IPv4 tunneling driver
[   11.870000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.210000] NET: Registered protocol family 24
[   12.330000] nf_conntrack version 0.5.0 (457 buckets, 1828 max)
[   12.750000] PPTP driver version 0.8.5
[   13.420000] xt_time: kernel timezone is -0000
[   14.010000]  Hooked IMQ after mangle on PREROUTING
[   14.020000]  Hooked IMQ after nat on POSTROUTING
[   14.020000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
[   14.160000] Netfilter messages via NETLINK v0.30.
[   14.210000] ip_set: protocol 6
[   18.670000] device eth0 entered promiscuous mode
[   18.900000] eth0: link up (100Mbps/Full duplex)
[   18.900000] br-lan: port 1(eth0) entered forwarding state
[   18.910000] br-lan: port 1(eth0) entered forwarding state
[   20.910000] br-lan: port 1(eth0) entered forwarding state
[   26.820000] device wlan0 entered promiscuous mode
[   27.100000] wlan0: authenticate with 00:15:6d:af:80:e4
[   27.130000] wlan0: send auth to 00:15:6d:af:80:e4 (try 1/3)
[   27.140000] wlan0: authenticated
[   27.150000] wlan0: associate with 00:15:6d:af:80:e4 (try 1/3)
[   27.160000] wlan0: RX AssocResp from 00:15:6d:af:80:e4 (capab=0x411 status=0 aid=1)
[   27.170000] wlan0: associated
[   27.170000] br-lan: port 2(wlan0) entered forwarding state
[   27.180000] br-lan: port 2(wlan0) entered forwarding state
[   29.180000] br-lan: port 2(wlan0) entered forwarding state
[   41.400000] ipt_bandwidth: timezone shift of 120 minutes detected, adjusting
[   41.400000]                old minutes west=0, new minutes west=-120

(Last edited by mersis on 12 Sep 2015, 14:10)

Hi I just got the device.
Could you please provide me the username password for access ssh?
Please....

Following the marketing material, telnet, not ssh, is available and in all probability is the web interface password.

I have try but telnet work. it works only ssh.

The discussion might have continued from here.