Hi, fellows,
I'm a newbie here and wanna see if the captioned vdsl modem (model: Huawei HG620) compatible with openwrt. Having prized open and found it seemed to be a variant to Huawei HG622 (which had been covered at: https://wiki.openwrt.org/toh/huawei/hg622) except dsl modem part, after had it connected to ttl and the original bootlogs are as follows:-
======
CFE version 1.0.37-102.6 for BCM96368 (32bit,SP,BE)
Build Date: Thu Sep 1 20:44:49 CST 2011 (mengxianwei@build.huawei.com)
Copyright (C) 2000-2008 Broadcom Corporation.
Parallel flash device: name MX29LV320AT, id 0x22a7, size 4096KB
CPU type 0x2A031: 400MHz, Bus: 160MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Boot Address 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 3
Boot image (0=latest, 1=previous) : 0
Board Id (0-5) : 96368MBG
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:e0:fc:09:09:09
PSI Size (1-64) KBytes : 64
Main Thread Number [0|1] : 0
*** Press any key to stop auto run (3 seconds) ***
Auto run second count down: 0
Decompression OK!
Entry at 0x8020c000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
96 buffers found.
Closing DMA Channels.
Starting program at 0x8020c000
Linux version 2.6.21.5 (mengxianwei@build.huawei.com) (gcc version 4.2.3) #46 Th
u Sep 1 20:56:33 CST 2011
Flash Chip ID = 0022
Pri Table Addr = 0040
ulBootFlag = 0003
ATP_FLASHCBB_InitSector i=1,ulBase=0x00000000
ATP_FLASHCBB_InitSector i=0,ulBase=0x00000000
Flash 0 at 0xb8000000
Size : 4 MB
Regions : 2
0 : 0x003f0000 - 0x00002000 * 8
1 : 0x00000000 - 0x00010000 * 63
CHIP96368 prom init
CPU revision is: 0002a031
Determined physical RAM map:
memory: 01f00000 @ 00000000 (usable)
On node 0 totalpages: 7936
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 30 pages used for memmap
Normal zone: 3810 pages, LIFO batch:0
Built 1 zonelists. Total pages: 7874
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 64kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (21 instructions).
Synthesized TLB load handler fastpath (33 instructions).
Synthesized TLB store handler fastpath (33 instructions).
Synthesized TLB modify handler fastpath (32 instructions).
PID hash table entries: 128 (order: 7, 512 bytes)
Using 200.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29124k/31744k available (1635k kernel code, 2620k reserved, 393k data, 8
8k init, 0k highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80300000 ... 0x80400000>
Calibrating delay loop... 398.95 BogoMIPS (lpj=997376)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
BLOG v1.0 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 128 (order: -3, 512 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
io scheduler noop registered (default)
PPP generic driver version 2.4.2
NET: Registered protocol family 24
IMQ starting with 3 devices...
IMQ driver loaded successfully.
Hooking IMQ before NAT on PREROUTING.
Hooking IMQ after NAT on POSTROUTING.
===start to init mtd=222========
bcm963xx_mtd driver v2.0
==boot from main kernel==
Registered device mtd[BCM63XX RootFS] dev[0] Flash[0xb8010100,3002368]
bhal: bhal_init entry
Led_module_init ok<6>Serial: BCM63XX driver $Revision: 1.1 $
ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX
bcmxtmrt: Broadcom BCM6368B2 ATM/PTM Network Device v0.1 Sep 1 2011 17:31:19
GACT probability on
Mirror/redirect action on
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (248 buckets, 1984 max)
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 88k freed
init started: BusyBox v1.9.1 (2011-09-01 17:33:40 CST)
starting pid 56, tty '': '/etc/init.d/rcS'
RCS DONE
starting pid 58, tty '': '/bin/sh'
BusyBox v1.9.1 (2011-09-01 17:33:40 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
-/bin/sh: can't access tty; job control turned off
mknod: /dev/boardled: File exists
-/bin/sh: usbserver: not found
Loading drivers and kernel modules...
pktflow: module license 'Proprietary' taints kernel.
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Constructed Broadcom Packet Flow Cache v0.1 Aug 28 2009 07:52:33
Broadcom Packet CMF (Experimental) Char Driver v0.1 Aug 28 2009 07:52:30 Registe
red<232>
Broadcom Packet CMF (Experimental) [6368-B2] v0.1 Aug 28 2009 07:52:30 Loaded
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCM6368B2 Ethernet Network Device v0.1 Sep 1 2011 17:31:06
KLOB extended to 2 pools
KLOB extended to 3 pools
KLOB extended to 4 pools
KLOB extended to 5 pools
KLOB extended to 6 pools
dgasp: kerSysRegisterDyingGaspHandler: eth0 registered
Broadcom Packet CMF (Experimental) SWC RESET.
Broadcom Packet CMF (Experimental) SWC INITIALIZED.
KLOB extended to 7 pools
KLOB extended to 8 pools
Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Aug 28 2009 07:52
:31 Registered
Broadcom Packet CMF (Experimental) Forwarder Net Device 1 v0.1 Aug 28 2009 07:52
:31 Registered
Broadcom Packet CMF (Experimental) ENABLED.
eth0.2: MAC Address: 20:2B:C1:AB:74:F9
eth0.3: MAC Address: 20:2B:C1:AB:74:F9
eth0.4: MAC Address: 20:2B:C1:AB:74:F9
eth0.5: MAC Address: 20:2B:C1:AB:74:F9
eth0.4 Link UP 100 mbps full duplex
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:01.0 to 64
=== pAd = c00e8000, size = 448024 ===
<-- RTMPAllocAdapterBlock, Status=0
pAd->CSRBaseAddress =0xb1000000, csr_addr=0xb1000000!
-----mc is cut-----
2000-1-1 0:0:5 Warning 10400 KLOB Pool 1 Initialized: 1048576 bytes <0x80300000
... 0x80400000>
Config File is error. Havn't start or end tag.
read default config file!!!!!!!!!!!
TSP_DBGetPara ok ulPort = 23
wandev: Debug 0 File:wdconfig.c, Line:108 Wan num[3] is invalid.
Waiting for cli start!
ATP_WLAN_Init Function In.
WlanBasicParaCheck in
WlanAllBasicParaCheck ok.
WlanSecureParaCheck in
WlanAllSecureParaCheck ok.
WlanSetupAll start
port_no -1 not surported, br:br0, port:wl0
device wl0 is not a slave of br0
port_no -1 not surported, br:br0, port:wl0.1
interface wl0.1 does not exist!
port_no -1 not surported, br:br0, port:wl0.2
interface wl0.2 does not exist!
port_no -1 not surported, br:br0, port:wl0.3
interface wl0.3 does not exist!
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
killall: rt2860apd: no process killed
RX DESC a1791000 size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
RTMPSetPhyMode: channel is out of range, use first channel=0
MCS Set = ff ff 00 00 01
RTMPFilterCalibration - can't find a valid value, loopcnt=102 stop calibratingSY
NC - BBP R4 to 20MHz.l
Welcome Visiting Huawei Home Gateway
Copyright by Huawei Technologies Co., Ltd.
Login:SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
Main bssid = 20:2b:c1:ab:74:f8
<==== rt28xx_init, Status=0
0x1300 = 00064320
connect[radius]: Network is unreachable
wl0wl0.1ssid set or display a configuration's SSID.
"wlancmd ssid set [-i SsidIndex] [<ssid>]"
If the configuration index 'SsidIndex' is not given,
configuraion #0 is assumed
wl0.2ssid set or display a configuration's SSID.
"wlancmd ssid set [-i SsidIndex] [<ssid>]"
If the configuration index 'SsidIndex' is not given,
configuraion #0 is assumed
wl0.3ssid set or display a configuration's SSID.
"wlancmd ssid set [-i SsidIndex] [<ssid>]"
If the configuration index 'SsidIndex' is not given,
configuraion #0 is assumed
wlan_mode set come in , argv[2] = bgnmixed
Txpower = 20
wl0wl0.1wl0.2wl0.3
begin WlanSetupBridge...
Fast bridging set 0.
device wl0 entered promiscuous mode
br0: port 1(wl0) entering learning state
br0: topology change detected, propagating
br0: port 1(wl0) entering forwarding state
Fast bridging set 1.
begin WlanStartServices...
Terminate the task(RtmpWscTask) with pid(296)!
br0: port 1(wl0) entering disabled state
BcmAdsl_Initialize=0xC00A168C, g_pFnNotifyCallback=0xC00D0D34
Clocks for QPROC and AFE are being aligned with step through ...
AFE is aligned, i = 050, PhaseValue = -050, PhaseCntl = 0x3FCE0000
QPROC is aligned, i = 051, PhaseValue = -050, PhaseCntl = 0x3FCE3FCD
Clocks for QPROC and AFE are aligned with syn_status AFE = 0x70, QPROC = 0x70
AFE phase control reg @0xb0f570f8 default actual = 0x0021C38F, exp = 0x0021c38f
QPRC phase control reg @0xb0f5f0c0 default actual = 0x0421C38F, exp = 0x0421c38f
pSdramPHY=0xA1FFFFF8, 0xB739 0xDEADBEEF
*** XfaceOffset: 0x5FF90 => 0x5FF90 ***
*** PhySdramSize got adjusted: 0xBE300 => 0xEBA20 ***
AdslCoreSharedMemInit: shareMemAvailable=83392
*** XdslCoreHwReset6306 ***
**** SetupReferenceClockTo6306 ****
*** XdslCoreHwReset6306 ***
**** PLLPowerUpSequence6306 ****
*** XdslCoreHwReset6306 ***
AdslCoreHwReset: AdslOemDataAddr = 0xA1FB3C78
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
bcmxtmrt: MAC address: 20 2b c1 ab 74 f9
device eth0.2 entered promiscuous mode
device eth0.3 entered promiscuous mode
device eth0.4 entered promiscuous mode
device eth0.5 entered promiscuous mode
device eth0 is not a slave of br0
error: unknown connection type!
error: unknown connection type!
error: unknown connection type!
error: unknown connection type!
atp: cur kernel version:[2.6.21.5]
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
ptm1.14: add 01:00:5e:00:00:01 mcast address to master interface
ptm1.14: del 01:00:5e:00:00:01 mcast address from vlan interface
ptm1.14: del 01:00:5e:00:00:01 mcast address from master interface
ptm1.14: Setting MAC address to 20 2b c1 ab 74 fb.
device ptm1 entered promiscuous mode
VLAN (ptm1.14): Setting underlying device (ptm1) to promiscious mode.
ptm1.14: add 01:00:5e:00:00:01 mcast address to master interface
bridge: can't decode speed from ptm1.14: 0
ptm1.14: dev_set_promiscuity(master, 1)
device ptm1.14 entered promiscuous mode
br0: port 6(ptm1.14) entering learning state
br0: topology change detected, propagating
br0: port 6(ptm1.14) entering forwarding state
ptm1.15: add 01:00:5e:00:00:01 mcast address to master interface
ptm1.15: del 01:00:5e:00:00:01 mcast address from vlan interface
ptm1.15: del 01:00:5e:00:00:01 mcast address from master interface
ptm1.15: Setting MAC address to 20 2b c1 ab 74 fc.
ptm1.15: add 01:00:5e:00:00:01 mcast address to master interface
bridge: can't decode speed from ptm1.15: 0
br0: port 7(ptm1.15) entering learning state
br0: topology change detected, propagating
br0: port 7(ptm1.15) entering forwarding state
ptm1.16: add 01:00:5e:00:00:01 mcast address to master interface
ptm1.16: del 01:00:5e:00:00:01 mcast address from vlan interface
ptm1.16: del 01:00:5e:00:00:01 mcast address from master interface
ptm1.16: Setting MAC address to 20 2b c1 ab 74 fd.
bridge: can't decode speed from ptm1.15: 0
ptm1.16: add 01:00:5e:00:00:01 mcast address to master interface
bridge: can't decode speed from ptm1.16: 0
br0: port 8(ptm1.16) entering learning state
br0: topology change detected, propagating
br0: port 8(ptm1.16) entering forwarding state
ptm1.301: add 01:00:5e:00:00:01 mcast address to master interface
ptm1.301: del 01:00:5e:00:00:01 mcast address from vlan interface
ptm1.301: del 01:00:5e:00:00:01 mcast address from master interface
ptm1.301: Setting MAC address to 20 2b c1 ab 74 fe.
ptm1.301: add 01:00:5e:00:00:01 mcast address to master interface
bridge: can't decode speed from ptm1.301: 0
br0: port 9(ptm1.301) entering learning state
br0: topology change detected, propagating
br0: port 9(ptm1.301) entering forwarding state
ptm1.4014: add 01:00:5e:00:00:01 mcast address to master interface
ptm1.4014: del 01:00:5e:00:00:01 mcast address from vlan interface
ptm1.4014: del 01:00:5e:00:00:01 mcast address from master interface
ptm1.4014: Setting MAC address to 20 2b c1 ab 74 ff.
ptm1.4014: add 01:00:5e:00:00:01 mcast address to master interface
bridge: can't decode speed from ptm1.301: 0
Broadcom Packet CMF (Experimental) ENABLED.
Broadcom Packet Flow Cache learning via BLOG enabled.
DNS Server version: V100R002C05B022SP01 dns server V1.2.5.0.3
Broadcom Packet CMF (Experimental) ENABLED.
Broadcom Packet Flow Cache learning via BLOG enabled.
Fast bridging set 1.
RTNETLINK answers: No such file or directory
Action 4 device imq0 ifindex 2
Broadcom Packet Flow Cache learning via BLOG disabled.
Broadcom Packet CMF (Experimental) ENABLED.
Broadcom Packet Flow Cache learning via BLOG enabled.
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
Timezone is wrong in Function: SntpTzOrderByNames, Line: 325.
The string of TimeZone exceed in Function: ATP_SNTP_SetVar, Line: 692.
Sntp doesn't enable!
sh: usbmount: not found
Bind failed: Address already in use
xtmcfgdrv: port mirroring config.
xtmcfgdrv: port mirroring config.
Stop mirror atm package to eth0.5
2000-1-1 0:0:25 Notice 1 System up
CWMP app version: V100R002C05B022 cwmp app V1.2.3.0.0
CWMP stk version: V100R002C05B022 cwmp stk V1.2.3.0.0
Not save certification!!!
ConfigDefaultSsl return: 0
2000-1-1 0:0:26 Debug 104500 LAN3 up
br0: port 4(eth0.4) entering learning state
br0: topology change detected, propagating
br0: port 4(eth0.4) entering forwarding state
TR064/UPnP ATP upnp v1.5 Start...
LAN IP: 169.254.100.156
SSDP server socket OK!
ATP_UPnP_Start Now...!
=======