then this image?

lede-mvebu-linksys-wrt1900acs-squashfs-factory.img

Yes, that is correct.

wish me luck! 

** Keep in mind please, though v2 of acs is identical hardware as acs v1, I don't know that it is "officially" supported. You are welcome to give it a try though, and from what I understand others with v2 are not having any issues... Still, you probably need to know just in case.

Best Regards,

flashed back to stock

getting this on page is that ok?

http://192.168.1.1/cgi-bin/luci

End User License Agreement|Terms of Service|Privacy Statement|Third Party Licenses
© 2016 Belkin International, Inc. and/or its affiliates. All rights reserved.

clear browser cache

davidc502 wrote:

Since you are on OpenWrt Chaos Calmer 15.05.1, Yes, I recommend going to stock first and then to lede.
I tried going from OpenWrt to lede, and it was a bit of a mess. lol  So, I had to go to stock and then back to lede, and it worked fine.

I took my wrt1900ac v1 from Chaos Calmer 15.05.1 to your build directly ie  LEDE build 4.4.19.
The caveat when doing the direct flash is DO NOT SAVE SETTINGS!

I manually entered the settings again on LEDE build 4.4.19 without issue.

Then on the LEDE build I did save settings on the full flash from 4.4.19 to 4.4.23 again without issue.

Thus to recap   Chaos Calmer 15.05.1  to  LEDE 4.4.19 or 4.4.23   (DO NOT SAVE SETTINGS!)

LEDE 4.4.19 to 4.4.23  one can save settings without issue.   

I hope that is clear as mud...

Cheers

Hans

thanks for the help guys....will now test and flash davidc502 firmware in the morning 

Helo David,
I'm WRT1900ACS with LEDE . Previusly I used a WRT1900AC v1 with your fw too. Thanks for your job, are really good!!

Are you planing to update the repo of the latest LEDE? I miss adblock, transmission, etc.

Thanks

I've had some difficulties with the repo, but am starting to build it back up.

Right now I'm adding modules by request, so what package names will you be needing?

@davidc502

Big thanks for the latest build! I finally have the NFS server and UPS monitor up and running, yeay!

I've noticed that you need to switch from lede built packages to your repo back and forth to get everything installed. For example, ca-certificates is only available from the lede repo?

up and running

how how to setup wireless....via web interface 

got the 2ghz working on radio 1

but radio 0 which is 5ghz nothing...set up but mac not seeing it  set to auto

Marvell 88W8864 802.11nac (radio0)

Wireless Network: Unknown "5G" (radio0.network1)
SSID: 5G | Mode: Unknown
wireless is disabled or not associated

both are turned on?

Linksys WRT1900ac
  Version 1 Hardware **NEW LEDE Build available** Mamba

  Version 2 Hardware **NEW LEDE Build available** Cobra

  Renamed ACS **NEW LEDE Build available** Shelby

should have i instated cobra as i am a V2?

(Last edited by liamhere on 9 Oct 2016, 13:09)

Hi davidc502 I was think of swiching to your build the packages i would like to use are adblock and Luci SQM QOS is a must in my house lol

@liamhere,

If you have the V2 of the 1900ac, then you need to install the cobra image. (It has different hardware than the V1)

humm thanks for that....ill now try cobra and see if the 5ghz comes on....but flash back to stock to be on the safe side 1st 

@liamhere,

I thought you owned 1900ac(s) v2  ?

@davidc502,

I miss the luci-app-bcp38 package and dependencies in the latest build.
This one, when included previously, always worked fine, without dependency errors.

Adri.

i do....so i need cobra?

as per you page yes?

Version 2 Hardware **NEW LEDE Build available** Cobra

as i am sure i installed shelby 

(Last edited by liamhere on 9 Oct 2016, 16:09)

@liamhere

Log into lede LuCi and copy the model number from "OverView"

Model    Linksys WRT1900ACS  <<< This is my model off of the OverView page in Luci.

Model    Linksys WRT1900ACS...thats all it says

Firmware Version    Lede reboot r1811 / LuCI Master (git-16.280.54886-e06c60a)

(Last edited by liamhere on 9 Oct 2016, 16:15)

Okay, then you are on Shelby which is correct.

What -  Mode, Channel, and Width is 5Ghz set to?

bugger....just flashed back to factory....ill reinstall shelby and get back to you

sorry to be a pain david

(Last edited by liamhere on 9 Oct 2016, 16:41)

flashed back onto shelby...now both wifi are now unknown?

5ghz mode AC  channel 66 (5180mhz) width 80

2ghz mode N channel AUTO width 20

@liamhere

1st -- Please set your country of origin in Wireless, choose 5Ghz > edit > Advanced configuration.
2nd -- Do the same for 2.4Ghz

3rd -- Set 5Ghz to channel 36 and save.

Do you have a SSID set? Also, do you have a wireless security set?

1st -- Please set your country of origin in Wireless, choose 5Ghz > edit > Advanced configuration.  DONE ALREADY
2nd -- Do the same for 2.4Ghz  DONE
3rd -- Set 5Ghz to channel 36 and save.
Do you have a SSID set? SET @ 2G and 5G

Also, do you have a wireless security set?  yes both set to WPA2- PSK