OpenWrt Forum Archive

Topic: D-Link DSL-2741B rev. E1

The content of this topic has been archived on 2 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

Post #1
mtrakal
24 Sep 2017, 19:47

Hi, is there someone who could help me to integrate DSL-2741B revision E1?

h**ps://wiki.openwrt.org/toh/d-link/dsl-2740b

Serial port boot log:

CFE version 1.0.37-102.6 for BCM96358 (32bit,SP,BE)
Build Date: 五 11月 27 15:15:53 CST 2009 (jie@jie-desktop)
Copyright (C) 2000-2008 Broadcom Corporation.

Parallel flash device: name MX29LV640BT, id 0x22c9, size 8192KB
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Boot Address 0xbe000000


Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Board Id (0-10)                   : AW4139B
Number of MAC Addresses (1-32)    : 11
Base MAC Address                  : 1c:af:f7:bb:fa:d7
PSI Size (1-128) KBytes            : 128
Main Thread Number [0|1]          : 0

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1
web info: Waiting for connection on socket 0.
CFE> help
Available commands:

sm                  Set memory or registers.
dm                  Dump memory or registers.
w                   Write the whole image start from beginning of the flash
e                   Erase [n]vram or [a]ll flash except bootrom
r                   Run program from flash image or from host depend on [f/h] flag
p                   Print boot line and board parameter info
c                   Change booline parameters
f                   Write image to the flash
i                   Erase persistent storage data
b                   Change board parameters
reset               Reset the board
flashimage          Flashes a compressed image after the bootloader.
help                Obtain help for CFE commands

For more information about a command, enter 'help command-name'
*** command status = 0
CFE> p
Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Board Id (0-10)                   : AW4139B
Number of MAC Addresses (1-32)    : 11
Base MAC Address                  : 1c:af:f7:bb:fa:d7
PSI Size (1-128) KBytes            : 128
Main Thread Number [0|1]          : 0

*** command status = 0
CFE>

CFE version 1.0.37-102.6 for BCM96358 (32bit,SP,BE)
Build Date: 五 11月 27 15:15:53 CST 2009 (jie@jie-desktop)
Copyright (C) 2000-2008 Broadcom Corporation.

Parallel flash device: name MX29LV640BT, id 0x22c9, size 8192KB
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Boot Address 0xbe000000


Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Board Id (0-10)                   : AW4139B
Number of MAC Addresses (1-32)    : 11
Base MAC Address                  : 1c:af:f7:bb:fa:d7
PSI Size (1-128) KBytes            : 128
Main Thread Number [0|1]          : 0

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xbe010000) ...
Code Address: 0x80010000, Entry Address: 0x80217000
Decompression OK!
Entry at 0x80217000
Closing network.
Closing DMA Channels.
Starting program at 0x80217000
Linux version 2.6.21.5 (root@jie-desktop) (gcc version 4.2.3) #1 Fri Apr 23 10:41:56 CST 2010
Parallel flash device: name MX29LV640BT, id 0x22c9, size 8192KB
AW4139B prom init
CPU revision is: 0002a010
Determined physical RAM map:
 memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 31 pages used for memmap
  Normal zone: 3969 pages, LIFO batch:0
Built 1 zonelists.  Total pages: 8033
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (21 instructions).
Synthesized TLB load handler fastpath (33 instructions).
Synthesized TLB store handler fastpath (33 instructions).
Synthesized TLB modify handler fastpath (32 instructions).
PID hash table entries: 128 (order: 7, 512 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29764k/32384k available (1784k kernel code, 2620k reserved, 287k data, 84k init, 0k highmem)
Calibrating delay loop... 299.00 BogoMIPS (lpj=747520)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Total Flash size: 8192K with 135 sectors
File system address: 0xbe010100
registering PCI controller with io_map_base unset
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
BLOG v1.0 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
io scheduler noop registered (default)
PPP generic driver version 2.4.2
NET: Registered protocol family 24
bcm963xx_mtd driver v1.0
usbmon: debugfs is not available
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: irq 18, io mem 0xfffe1300
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
hub 1-0:1.0: over-current change on port 2
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 13, io mem 0xfffe1400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.1
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x8025 is enabled
SES: LED GPIO 0x801a is enabled
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
bcmxtmrt: Broadcom BCM6358A1 ATM Network Device v0.1 Apr 23 2010 10:40:03
u32 classifier
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Bridge firewalling registered
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 84k freed
init started:  BusyBox v1.00 (2010.04.23-02:43+0000) multi-call binary


BusyBox v1.00 (2010.04.23-02:43+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.


Loading drivers and kernel modules...

cp: /bin/CP850.so: No such file or directory
bcmxtmcfg: module license 'Proprietary' taints kernel.
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Apr 23 2010 10:39:04
Config Ethernet Switch Through MDIO Pseudo PHY Interface
AsicVer.chipid=5988, AsicVer.vernum=0, AsicVer.revision=4
ethsw: found RTL8306G!
ethsw_setup_led is finished!
dgasp: kerSysRegisterDyingGaspHandler: eth0 registered
eth0: MAC Address: 1C:AF:F7:BB:FA:D7
Broadcom BCM6358A1 USB Network Device v0.4 Apr 23 2010 10:39:10
usb0: MAC Address: 1C AF F7 BB FA D7
usb0: Host MAC Address: 1C AF F7 BB FA D7
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:01.0 to 64
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: MAC addr from system pool. id:0x776c0000
wl0: MAC Address: 1C:AF:F7:BB:FA:D8
wl0: Broadcom BCMa8d6 802.11 Wireless Controller 5.10.120.0.cpe4.402.0
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered

===== Release Version EU_5.17 (build timestamp 2010.04.23-10:42:50) =====

wl_cnt= 1
eth0.2: MAC Address: 1C:AF:F7:BB:FA:D7
eth0.3: MAC Address: 1C:AF:F7:BB:FA:D7
eth0.4: MAC Address: 1C:AF:F7:BB:FA:D7
eth0.5: MAC Address: 1C:AF:F7:BB:FA:D7
SIOCGIFFLAGS: No such device
interface eth1 does not exist!
interface eth1 does not exist!
SIOCSIFADDR: No such device
device eth0.2 is not a slave of br0
device eth0.2 entered promiscuous mode
br0: port 1(eth0.2) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0.2) entering forwarding state
device eth0.3 is not a slave of br0
device eth0.3 entered promiscuous mode
br0: port 2(eth0.3) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0.3) entering forwarding state
device eth0.4 is not a slave of br0
device eth0.4 entered promiscuous mode
br0: port 3(eth0.4) entering learning state
br0: topology change detected, propagating
br0: port 3(eth0.4) entering forwarding state
device eth0.5 is not a slave of br0
device eth0.5 entered promiscuous mode
br0: port 4(eth0.5) entering learning state
br0: topology change detected, propagating
br0: port 4(eth0.5) entering forwarding state
device usb0 is not a slave of br0
device usb0 entered promiscuous mode
br0: port 5(usb0) entering learning state
br0: topology change detected, propagating
br0: port 5(usb0) entering forwarding state
WLmngr Daemon is running
optarg=0 shmId=0
device wl0 is not a slave of br0
device wl0 entered promiscuous mode
br0: port 6(wl0) entering learning state
br0: topology change detected, propagating
br0: port 6(wl0) entering forwarding state
BcmAdsl_Initialize=0xC00601D8, g_pFnNotifyCallback=0xC007CBA4
AnnexCParam=0x00000000 AnnexAParam=0x00000980 adsl2=0x00000000
pSdramPHY=0xA1FFFFF8, 0xF7EB929A 0xDCADBAEF
AdslCoreSharedMemInit: shareMemAvailable=23280
AdslCoreHwReset:  AdslOemDataAddr = 0xA1FF9504
AnnexCParam=0x00000000 AnnexAParam=0x00000980 adsl2=0x00000000
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
passer: Failed to send netlink message: Connection refused
wlctl -i wl0 phytype > /var/wl0
wlctl -i wl0 revinfo > /var/wl0
wlctl -i wl0 bands > /var/wl0bands
wlctl ver > /var/wlver
wlctl -i wl0 cap > /var/wl0cap
device wl0 left promiscuous mode
br0: port 6(wl0) entering disabled state
device wl0 is not a slave of br0
device wl0 entered promiscuous mode
br0: port 6(wl0) entering learning state
br0: topology change detected, propagating
br0: port 6(wl0) entering forwarding state
interface wl0.1 does not exist!
interface wl0.2 does not exist!
interface wl0.3 does not exist!
br0: port 6(wl0) entering disabled state
InValid Device Pin in CFE
WPS Device PIN = 56118278
wlctl -i wl0 phy_watchdog 0
wlctl -i wl0 wds none
wlctl -i wl0 up
wlctl -i wl0 down
wlctl -i wl0 mbss 0
wlctl -i wl0 bss -C 0 down
wlctl -i wl0 bss -C 1 down
wlctl -i wl0 bss -C 2 down
wlctl -i wl0 bss -C 3 down
wlctl -i wl0 ssid -C 0 'm''t''r''a''k''a''l''.''c''z'
Setting SSID "mtrakal.cz"
wlctl -i wl0 ssid -C 1 'w''l''0''_''G''u''e''s''t''1'
Setting SSID "wl0_Guest1"
wlctl -i wl0 ssid -C 2 'w''l''0''_''G''u''e''s''t''2'
Setting SSID "wl0_Guest2"
wlctl -i wl0 ssid -C 3 'w''l''0''_''G''u''e''s''t''3'
Setting SSID "wl0_Guest3"
WPS Mode = []
wlctl -i wl0 cur_etheraddr 1C:AF:F7:BB:FA:D8  2>/dev/null
wlctl -i wl0.1 cur_etheraddr 5a:af:f7:bb:fa:d9  2>/dev/null
wlctl -i wl0.2 cur_etheraddr 5a:af:f7:bb:fa:da  2>/dev/null
wlctl -i wl0.3 cur_etheraddr 5a:af:f7:bb:fa:db  2>/dev/null
wlctl -i wl0  ap 1
wlctl -i wl0 infra 1
wlctl -i wl0 closed 0
wlctl -i wl0 country GB
wlctl -i wl0  band b
wlctl -i wl0 regulatory 0
wlctl -i wl0 radar 0 2>/dev/null
wlctl -i wl0 spect 0 2>/dev/null
wlctl -i wl0 nmode -1
wlctl -i wl0 mimo_bw_cap 1
wlctl -i wl0 chanspec -c 5 -b 2 -w 40 -s -1
Chanspec set to 0x2d05
wlctl -i wl0 wpa_cap -C 0 > /var/wpa_cap0
wlctl -i wl0 wpa_cap -C 0 0 2>/dev/null
wlctl -i wl0 wpa_cap -C 1 > /var/wpa_cap0
wlctl -i wl0 wpa_cap -C 1 0 2>/dev/null
wlctl -i wl0 wpa_cap -C 2 > /var/wpa_cap0
wlctl -i wl0 wpa_cap -C 2 0 2>/dev/null
wlctl -i wl0 wpa_cap -C 3 > /var/wpa_cap0
wlctl: Unsupported
wlctl -i wl0 wpa_cap -C 3 0 2>/dev/null
wlctl -i wl0 maxassoc 16
wlctl -i wl0 bss_maxassoc 16
wlctl -i wl0 gmode Auto
wlctl -i wl0 gmode_protection_override -1
wlctl -i wl0 gmode_protection_control 2
wlctl -i wl0 nmode_protection_override -1
wlctl -i wl0 protection_control 2
wlctl -i wl0 nreqd 0
wlctl -i wl0 wme 0 2>/dev/null
wlctl -i wl0 afterburner_override 0 2>/dev/null
wlctl -i wl0 ampdu 1
wlctl -i wl0 amsdu 1
wlctl -i wl0 afterburner_override 0
wlctl -i wl0 wme 0 2>/dev/null
wlctl -i wl0 wme_noack 0 2>/dev/null
wlctl -i wl0 wme_apsd 1 2>/dev/null
wlctl -i wl0 wme_bss_disable 0
wlctl -i wl0 nmode 0
wlctl -i wl0 gmode 1
wlctl -i wl0 nmode 1
wlctl -i wl0 rate 0
wlctl -i wl0 bg_rate 0
wlctl -i wl0 leddc 0 2>/dev/null
wlctl -i wl0 mrate -1
wlctl -i wl0 bg_mrate -1
wlctl -i wl0 rateset default
wlctl -i wl0 rtsthresh 2347
wlctl -i wl0 fragthresh 2346
wlctl -i wl0 dtim 1
wlctl -i wl0  bi 100
wlctl -i wl0 frameburst 0
wlctl -i wl0 ap_isolate 0
wlctl -i wl0 wds none
wlctl -i wl0 pwr_percent 100
wlctl -i wl0 wmf_bss_enable 0
wlctl -i wl0.1 wmf_bss_enable 0
wlctl -i wl0.2 wmf_bss_enable 0
wlctl -i wl0.3 wmf_bss_enable 0
wlctl -i wl0 mac none
wlctl -i wl0 macmode 0
wlctl -i wl0 lazywds 1
wlctl -i wl0 wds
wlctl -i wl0 up
wlctl -i wl0 csscantimer 0
wlctl -i wl0 chanspec > /var/curchaspec0
br0: port 6(wl0) entering learning state
br0: topology change detected, propagating
br0: port 6(wl0) entering forwarding state
ifconfig: eth1: error fetching interface information: Device not found

device wl0 left promiscuous mode
br0: port 6(wl0) entering disabled state
device wl0 is not a slave of br0
device wl0 entered promiscuous mode
br0: port 6(wl0) entering learning state
br0: topology change detected, propagating
br0: port 6(wl0) entering forwarding state
device wl0.1 is not a slave of br0
device wl0.2 is not a slave of br0
device wl0.3 is not a slave of br0
Reaped 588
UPnP daemon is ready to run
WPS aplockdown init: limit = 30, duration = 300, ageout = 300!
First Sync : Wireless enabled !!!

BCM96358 xDSL Router
Login: admin
Password:
 > sh


BusyBox v1.00 (2010.04.23-02:43+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.

# ls
bin      etc      linuxrc  proc     tmp      var
dev      lib      mnt      sbin     usr      webs
# help

Built-in commands:
-------------------
        . : break cd continue eval exec exit export help login newgrp
        read readonly set shift times trap umask wait [ busybox cat chmod
        cp date df dmesg echo expr false fdisk ftpget ifconfig init insmod
        kill killall klogd linuxrc ln logger logread ls mkdir mknod mount
        msh ping ping6 ps pwd reboot rm rmmod route sendarp sh sleep
        smuxctl sysinfo syslogd test tftp tftpd top true tty umount vconfig


#

GPL source codes for Dlink DSL-2741B rev. E1: ftp://ftp.dlink.de/dsl/dsl-2741b/driver … ode.tar.gz

Binary original firmware: ftp://ftp.dlink.de/dsl/dsl-2741b/archiv … 100308.zip

Chipset: BCM6358 h**ps://wiki.openwrt.org/doc/hardware/soc/soc.broadcom.bcm63xx
Eth switch: RTL8306G h**p://realtek.info/pdf/rtl8306sd%28m%29_datasheet_1.1.pdf
WIFI: Broadcom BCMa8d6 802.11 Wireless Controller 5.10.120.0.cpe4.402.0
mira p3s56d40etp
some small chip: broadcom 5301ksg td0930p1

But I have no skill to integrate it sad.
I'm able to use linux and compile source codes by some tutorial/readme, but not to add unnecessary files to openwrt project.

I don't need ADSL, just use WIFI (must wantet as wifi client mode), and eth switch.

I think, that HW is almost same as revision C (same chipset, different RAM, maybe different wifi/eth switch?)

(Last edited by mtrakal on 24 Sep 2017, 20:48)

Post #2
mtrakal
26 Sep 2017, 01:14

I was able to flash DSL-2741B rev. C3 successfully, but I can't ping eth0.1. LED and console show when link up/down, but ping doesn't work.
PC is connected directly and set ip on 192.168.1.100/24

Flashing root file system and kernel at 0xbe010000: .....................................................

.
*** Image flash done *** !

Resetting board...

CFE version 1.0.37-102.6 for BCM96358 (32bit,SP,BE)
Build Date: 五 11月 27 15:15:53 CST 2009 (jie@jie-desktop)
Copyright (C) 2000-2008 Broadcom Corporation.

Parallel flash device: name MX29LV640BT, id 0x22c9, size 8192KB
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Boot Address 0xbe000000


Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Board Id (0-10)                   : AW4139B
Number of MAC Addresses (1-32)    : 11
Base MAC Address                  : 1c:af:f7:bb:fa:d7
PSI Size (1-128) KBytes            : 128
Main Thread Number [0|1]          : 0

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xbe010000) ...
Code Address: 0x80A00000, Entry Address: 0x80a00000
LZMA: Prossible old LZMA format, trying to decompress..
Decompression OK!
Entry at 0x80a00000
Closing network.
Closing DMA Channels.
Starting program at 0x80a00000
[    0.000000] Linux version 3.18.23 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r48532) ) #1 Tue Mar 1 10:07:16 CET 2016
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 32MB of RAM installed
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: 1.0.37-102.6
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board: board name: AW4139
[    0.000000] MIPS: machine is D-Link DSL-2740B/DSL-2741B rev C2/3
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Memory: 27480K/32768K available (2761K kernel code, 138K rwdata, 460K rodata, 1304K init, 192K bss, 5288K reserved)
[    0.000000] NR_IRQS:256
[    0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[    0.040000] pid_max: default: 32768 minimum: 301
[    0.044000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.048000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.060000] NET: Registered protocol family 16
[    0.068000] registering PCI controller with io_map_base unset
[    0.072000] registering PCI controller with io_map_base unset
[    0.088000] PCI host bridge to bus 0000:00
[    0.092000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.096000] pci_bus 0000:00: root bus resource [io  0x8000000-0x8007fff]
[    0.100000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.108000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30003fff]
[    0.112000] PCI host bridge to bus 0000:01
[    0.116000] pci_bus 0000:01: root bus resource [mem 0x38000000-0x3fffffff]
[    0.120000] pci_bus 0000:01: root bus resource [io  0x8008000-0x800ffff]
[    0.124000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[    0.128000] pci 0000:01:1e.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.132000] pci 0000:01:1e.0: BAR 10: assigned [mem 0x38000000-0x3fffffff]
[    0.136000] pci 0000:01:1e.0: BAR 7: assigned [io  0x8008000-0x80080ff]
[    0.140000] pci 0000:01:1e.0: BAR 8: assigned [io  0x8008400-0x80084ff]
[    0.144000] pci 0000:01:1e.0: CardBus bridge to [bus 02-05]
[    0.148000] pci 0000:01:1e.0:   bridge window [io  0x8008000-0x80080ff]
[    0.152000] pci 0000:01:1e.0:   bridge window [io  0x8008400-0x80084ff]
[    0.156000] pci 0000:01:1e.0:   bridge window [mem 0x38000000-0x3fffffff]
[    0.160000] Switched to clocksource MIPS
[    0.164000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[    0.196000] ssb: Found chip with id 0xA8D6, rev 0x00 and package 0x08
[    0.240000] ssb: WARNING: Using fallback SPROM failed (err -2)
[    0.244000] ssb: WARNING: Invalid SPROM CRC (corrupt SPROM)
[    0.252000] ssb: Unsupported SPROM revision 255 detected. Will extract v1
[    0.280000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
[    0.288000] NET: Registered protocol family 2
[    0.296000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.304000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.308000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.316000] TCP: reno registered
[    0.320000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.328000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.332000] NET: Registered protocol family 1
[    0.340000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.348000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.356000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.364000] msgmni has been set to 53
[    0.372000] io scheduler noop registered
[    0.376000] io scheduler deadline registered (default)
[    0.384000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10, base_baud = 1562500) is a bcm63xx_uart
[    0.392000] console [ttyS0] enabled
[    0.392000] console [ttyS0] enabled
[    0.400000] bootconsole [early0] disabled
[    0.400000] bootconsole [early0] disabled
[    0.408000] 1e000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022c9
[    0.420000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.424000]   Amd/Fujitsu Extended Query version 1.1.
[    0.432000] 1e000000.nor: Swapping erase regions for top-boot CFI table.
[    0.436000] number of CFI chips: 1
[    0.440000] bcm63xxpart: CFE boot tag found with version 6 and board type AW4139
[    0.448000] 5 bcm63xxpart partitions found on MTD device 1e000000.nor
[    0.456000] Creating 5 MTD partitions on "1e000000.nor":
[    0.460000] 0x000000000000-0x000000010000 : "CFE"
[    0.468000] 0x000000010100-0x00000012ab9e : "kernel"
[    0.476000] 0x00000012ab9e-0x0000003f0000 : "rootfs"
[    0.484000] mtd: device 2 (rootfs) set to be root filesystem
[    0.488000] 1 squashfs-split partitions found on MTD device rootfs
[    0.496000] 0x000000350000-0x0000003f0000 : "rootfs_data"
[    0.504000] 0x000000010000-0x0000003f0000 : "linux"
[    0.512000] 0x0000003f0000-0x000000400000 : "nvram"
[    0.520000] bcm63xx-spi bcm63xx-spi: at 0xfffe0800 (irq 9, FIFOs size 542)
[    0.556000] libphy: bcm63xx_enet MII bus: probed
[    0.560000] bcm63xx_enet bcm63xx_enet.1: attached PHY at address 0 [Generic PHY]
[    0.568000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.580000] TCP: cubic registered
[    0.584000] NET: Registered protocol family 17
[    0.588000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.600000] Bridge firewalling registered
[    0.604000] 8021q: 802.1Q VLAN Support v1.8
[    0.624000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.652000] Freeing unused kernel memory: 1304K (8035a000 - 804a0000)
[    2.416000] init: Console is alive
[    2.420000] init: - watchdog -
[    4.476000] init: - preinit -
[    5.412000] random: procd urandom read with 20 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.088000] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[    9.152000] procd: - early -
[    9.156000] procd: - watchdog -
[   10.200000] procd: - ubus -
[   11.212000] procd: - init -
Please press Enter to activate this console.
[   13.292000] NET: Registered protocol family 10
[   13.308000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   13.336000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[   13.344000] Backport generated by backports.git backports-20150129-0-gdd4a670
[   13.360000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   13.384000] nf_conntrack version 0.5.0 (449 buckets, 1796 max)
[   13.460000] xt_time: kernel timezone is -0000
[   13.512000] cfg80211: Calling CRDA to update world regulatory domain
[   13.572000] cfg80211: World regulatory domain updated:
[   13.576000] cfg80211:  DFS Master region: unset
[   13.580000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   13.592000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   13.600000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   13.608000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   13.616000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AU
[   13.624000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AU
[   13.636000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000
[   13.644000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 m
[   13.652000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0
[   13.776000] PPP generic driver version 2.4.2
[   13.784000] NET: Registered protocol family 24
[   13.844000] b43-phy0: Broadcom 43222 WLAN found (core revision 16)
[   13.884000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6
[   13.888000] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2056, Revision 6, Versio
[   13.908000] Broadcom 43xx driver loaded [ Features: PNL ]
[   21.828000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   28.304000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   28.328000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   28.332000] jffs2_build_filesystem(): erasing all blocks after the end marker
[   31.300000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   31.324000] device eth0.1 entered promiscuous mode
[   31.332000] device eth0 entered promiscuous mode
[   31.360000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   33.044000] random: nonblocking pool is initialized
[   34.084000] done.
[   34.088000] jffs2: notice: (776) jffs2_build_xattr_subsystem: complete buildi                                     checked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.



BusyBox v1.23.2 (2016-03-01 09:47:37 CET) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 CHAOS CALMER (15.05.1, r48532)
 -----------------------------------------------------
  * 1 1/2 oz Gin            Shake with a glassful
  * 1/4 oz Triple Sec       of broken ice and pour
  * 3/4 oz Lime Juice       unstrained into a goblet.
  * 1 1/2 oz Orange Juice
  * 1 tsp. Grenadine Syrup
 -----------------------------------------------------
root@OpenWrt:/# iwconfig
/bin/ash: iwconfig: not found
root@OpenWrt:/# ifconfig
br-lan    Link encap:Ethernet  HWaddr 1C:AF:F7:BB:FA:D7
          inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fd61:9f84:4222::1/60 Scope:Global
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth0      Link encap:Ethernet  HWaddr 1C:AF:F7:BB:FA:D7
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:10 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:2368 (2.3 KiB)  TX bytes:0 (0.0 B)
          Interrupt:14

eth0.1    Link encap:Ethernet  HWaddr 1C:AF:F7:BB:FA:D7
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:96 errors:0 dropped:0 overruns:0 frame:0
          TX packets:96 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:7200 (7.0 KiB)  TX bytes:7200 (7.0 KiB)

root@OpenWrt:/# uname -a
Linux OpenWrt 3.18.23 #1 Tue Mar 1 10:07:16 CET 2016 mips GNU/Linux
root@OpenWrt:/# cat /proc/version
Linux version 3.18.23 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r48532) ) #1 Tue Mar 1 10:07:16 CET 2016
root@OpenWrt:/# cat /proc/cpuinfo
system type             : bcm63xx/AW4139 (0x6358/0xA1)
machine                 : D-Link DSL-2740B/DSL-2741B rev C2/3
processor               : 0
cpu model               : Broadcom BMIPS4350 V1.0
BogoMIPS                : 299.26
wait instruction        : yes
microsecond timers      : yes
tlb_entries             : 32
extra interrupt vector  : yes
hardware watchpoint     : no
isa                     : mips1 mips2 mips32r1
ASEs implemented        :
shadow register sets    : 1
kscratch registers      : 0
package                 : 0
core                    : 0
VCED exceptions         : not available
VCEI exceptions         : not available

root@OpenWrt:/# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00010000 00010000 "CFE"
mtd1: 0011aa9e 00010000 "kernel"
mtd2: 002c5462 00010000 "rootfs"
mtd3: 000a0000 00010000 "rootfs_data"
mtd4: 003e0000 00010000 "linux"
mtd5: 00010000 00010000 "nvram"
root@OpenWrt:/# cat /proc/modules
pppoe 8000 0 - Live 0x80dda000
ppp_async 6304 0 - Live 0x80dde000
iptable_nat 688 1 - Live 0x80c5e000
b43 350496 0 - Live 0x80d80000
pppox 1136 1 pppoe, Live 0x80cb3000
ppp_generic 20208 3 pppoe,ppp_async,pppox, Live 0x80c50000
nf_nat_ipv4 3920 1 iptable_nat, Live 0x80c4d000
nf_conntrack_ipv6 5504 3 - Live 0x80d5c000
nf_conntrack_ipv4 5104 8 - Live 0x80c4e000
mac80211 366400 1 b43, Live 0x80d00000
ipt_REJECT 832 2 - Live 0x80cbd000
ipt_MASQUERADE 544 1 - Live 0x80cbc000
cfg80211 204960 2 b43,mac80211, Live 0x80c80000
xt_time 1552 0 - Live 0x81b7f000
xt_tcpudp 1632 8 - Live 0x81b79000
xt_state 608 0 - Live 0x81b7a000
xt_nat 992 0 - Live 0x81b6d000
xt_multiport 1104 0 - Live 0x81b76000
xt_mark 592 0 - Live 0x81b70000
xt_mac 544 0 - Live 0x81b74000
xt_limit 912 20 - Live 0x81b73000
xt_id 400 0 - Live 0x81b6e000
xt_conntrack 2112 10 - Live 0x81b6c000
xt_comment 400 60 - Live 0x81b6f000
xt_TCPMSS 2544 0 - Live 0x81b6b000
xt_REDIRECT 976 0 - Live 0x81b68000
xt_LOG 688 0 - Live 0x81b87000
xt_CT 2208 0 - Live 0x81b66000
slhc 3968 1 ppp_generic, Live 0x81b89000
nf_reject_ipv4 1696 1 ipt_REJECT, Live 0x81b64000
nf_nat_masquerade_ipv4 1168 1 ipt_MASQUERADE, Live 0x81b63000
nf_nat_ftp 1120 0 - Live 0x81b5b000
nf_nat 9472 5 nf_nat_ipv4,xt_nat,xt_REDIRECT,nf_nat_masquerade_ipv4,nf_nat_ftp, Live 0x81b60000
nf_log_ipv4 3056 0 - Live 0x81b8b000
nf_defrag_ipv6 8864 1 nf_conntrack_ipv6, Live 0x81b80000
nf_defrag_ipv4 720 1 nf_conntrack_ipv4, Live 0x81b9f000
nf_conntrack_rtcache 2400 0 - Live 0x81b5d000
nf_conntrack_ftp 5200 1 nf_nat_ftp, Live 0x81b5e000
nf_conntrack 44896 11 nf_nat_ipv4,nf_conntrack_ipv6,nf_conntrack_ipv4,xt_state,xt_conntrack,xt_CT,nf_nat_masquerade_ipv4,nf_nat_ftp,nf_nat,nf_conntrack_rtcache,nf_conntrack_ftp, Live 0x81b50000
iptable_raw 560 1 - Live 0x81bbe000
iptable_mangle 848 1 - Live 0x81af9000
iptable_filter 592 1 - Live 0x81b9a000
ip_tables 9200 4 iptable_nat,iptable_raw,iptable_mangle,iptable_filter, Live 0x81bb8000
crc_ccitt 944 1 ppp_async, Live 0x81afa000
compat 1120 3 b43,mac80211,cfg80211, Live 0x81af8000
ip6t_REJECT 1104 2 - Live 0x81b98000
nf_reject_ipv6 2016 1 ip6t_REJECT, Live 0x81b18000
nf_log_ipv6 3200 0 - Live 0x81afb000
nf_log_common 2272 2 nf_log_ipv4,nf_log_ipv6, Live 0x81afc000
ip6table_raw 496 1 - Live 0x81bb1000
ip6table_mangle 960 1 - Live 0x81b19000
ip6table_filter 528 1 - Live 0x81bb7000
ip6_tables 8976 3 ip6table_raw,ip6table_mangle,ip6table_filter, Live 0x81b90000
x_tables 9776 26 ipt_REJECT,ipt_MASQUERADE,xt_time,xt_tcpudp,xt_state,xt_nat,xt_multiport,xt_mark,xt_mac,xt_limit,xt_id,xt_conntrack,xt_comment,xt_TCPMSS,xt_REDIRECT,xt_LOG,xt_CT,iptable_raw,iptable_mangle,iptable_filter,ip_tables,ip6t_REJECT,ip6table_raw,ip6table_mangle,ip6table_filter,ip6_tables, Live 0x81bb4000
ipv6 262000 28 nf_conntrack_ipv6,nf_defrag_ipv6,nf_reject_ipv6,ip6table_mangle,[permanent], Live 0x81bc0000
arc4 1232 2 - Live 0x81add000
crypto_blkcipher 9744 1 arc4, Live 0x81b44000
gpio_button_hotplug 5936 0 - Live 0x81ad8000
root@OpenWrt:/# cat /proc/devices
Character devices:
  1 mem
  4 ttyS
  5 /dev/tty
  5 /dev/console
  5 /dev/ptmx
 10 misc
 90 mtd
108 ppp
128 ptm
136 pts
254 watchdog

Block devices:
259 blkext
 31 mtdblock
root@OpenWrt:/# free
             total         used         free       shared      buffers
Mem:         28784        16600        12184          100         1788
-/+ buffers:              14812        13972
Swap:            0            0            0
root@OpenWrt:/# cat /proc/meminfo
MemTotal:          28784 kB
MemFree:           12180 kB
MemAvailable:      18196 kB
Buffers:            1788 kB
Cached:             5532 kB
SwapCached:            0 kB
Active:             5760 kB
Inactive:           3088 kB
Active(anon):       1608 kB
Inactive(anon):       20 kB
Active(file):       4152 kB
Inactive(file):     3068 kB
Unevictable:           0 kB
Mlocked:               0 kB
SwapTotal:             0 kB
SwapFree:              0 kB
Dirty:                 0 kB
Writeback:             0 kB
AnonPages:          1548 kB
Mapped:             1832 kB
Shmem:               100 kB
Slab:               3976 kB
SReclaimable:        888 kB
SUnreclaim:         3088 kB
KernelStack:         248 kB
PageTables:          196 kB
NFS_Unstable:          0 kB
Bounce:                0 kB
WritebackTmp:          0 kB
CommitLimit:       14392 kB
Committed_AS:       3972 kB
VmallocTotal:    1032116 kB
VmallocUsed:        1404 kB
VmallocChunk:    1027680 kB
root@OpenWrt:/# cat /proc/iomem
00000000-01ffffff : System RAM
  00010000-002c2ad7 : Kernel code
  002c2ad8-00359a47 : Kernel data
08000000-0800ffff : bcm63xx PCI IO space
1e000000-1fffffff : 1e000000.nor
30000000-37ffffff : bcm63xx PCI memory space
  30000000-30003fff : 0000:00:01.0
    30000000-30003fff : b43-pci-bridge
38000000-3fffffff : bcm63xx Cardbus memory space
  38000000-3fffffff : PCI CardBus 0000:02
fffe005c-fffe0067 : bcm63xx-wdt
fffe0080-fffe0083 : /ubus@fff00000/gpio-controller@fffe0080
fffe0084-fffe0087 : /ubus@fff00000/gpio-controller@fffe0084
fffe0088-fffe008b : /ubus@fff00000/gpio-controller@fffe0080
fffe008c-fffe008f : /ubus@fff00000/gpio-controller@fffe0084
fffe0100-fffe0117 : bcm63xx_uart.0
  fffe0100-fffe0117 : bcm63xx
fffe0800-fffe0f0b : bcm63xx-spi
  fffe0800-fffe0f0b : bcm63xx-spi
fffe4800-fffe4fff : bcm63xx_enet.1
  fffe4800-fffe4fff : bcm63xx_enet.1
fffe5000-fffe50ff : bcm63xx_enet_shared.0
  fffe5000-fffe50ff : bcm63xx_enet_shared.0
fffe5100-fffe51ff : bcm63xx_enet_shared.0
  fffe5100-fffe51ff : bcm63xx_enet_shared.0
fffe5200-fffe52ff : bcm63xx_enet_shared.0
  fffe5200-fffe52ff : bcm63xx_enet_shared.0
root@OpenWrt:/# ps
  PID USER       VSZ STAT COMMAND
    1 root      1444 S    /sbin/procd
    2 root         0 SW   [kthreadd]
    3 root         0 SW   [ksoftirqd/0]
    4 root         0 SW   [kworker/0:0]
    5 root         0 SW<  [kworker/0:0H]
    6 root         0 SW   [kworker/u2:0]
    7 root         0 SW<  [khelper]
   17 root         0 SW<  [writeback]
   19 root         0 SW<  [bioset]
   21 root         0 SW<  [kblockd]
   92 root         0 SW   [kswapd0]
   93 root         0 SW   [kworker/0:1]
   94 root         0 SW   [fsnotify_mark]
   96 root         0 SW   [spi0]
  165 root         0 SW<  [deferwq]
  186 root         0 SW   [kworker/u2:2]
  284 root       904 S    /sbin/ubusd
  285 root      1492 S    /bin/ash --login
  411 root         0 SW<  [ipv6_addrconf]
  459 root         0 SW<  [cfg80211]
  643 root      1060 S    /sbin/logd -S 16
  652 root      1572 S    /sbin/rpcd
  687 root      1580 S    /sbin/netifd
  711 root      1196 S    /usr/sbin/odhcpd
  755 root      1484 S    /usr/sbin/telnetd -F -l /bin/login.sh
  770 root      1628 S    /usr/sbin/uh*tpd -f -h /ww*w -r OpenWrt -x /cgi-bin -
  837 root         0 SWN  [jffs2_gcd_mtd3]
  872 root      1488 S    /usr/sbin/ntpd -n -S /usr/sbin/ntpd-hotplug -p 0.ope
  887 nobody     992 S    /usr/sbin/dnsmasq -C /var/etc/dnsmasq.conf -k -x /va
  970 root      1156 S    /usr/sbin/dropbear -F -P /var/run/dropbear.1.pid -p
  983 root      1488 R    ps
root@OpenWrt:/# ifconfig
br-lan    Link encap:Ethernet  HWaddr 1C:AF:F7:BB:FA:D7
          inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fd61:9f84:4222::1/60 Scope:Global
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth0      Link encap:Ethernet  HWaddr 1C:AF:F7:BB:FA:D7
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:1031 errors:0 dropped:12 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:218489 (213.3 KiB)  TX bytes:0 (0.0 B)
          Interrupt:14

eth0.1    Link encap:Ethernet  HWaddr 1C:AF:F7:BB:FA:D7
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:720 errors:0 dropped:0 overruns:0 frame:0
          TX packets:720 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:49632 (48.4 KiB)  TX bytes:49632 (48.4 KiB)

root@OpenWrt:/# dmesg
[    0.000000] Linux version 3.18.23 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r48532) ) #1 Tue Mar 1 10:07:16 CET 2016
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 32MB of RAM installed
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: 1.0.37-102.6
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board: board name: AW4139
[    0.000000] MIPS: machine is D-Link DSL-2740B/DSL-2741B rev C2/3
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff]
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 8033e370, node_mem_map 81003060
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8192 pages, LIFO batch:0
[    0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Memory: 27480K/32768K available (2761K kernel code, 138K rwdata, 460K rodata, 1304K init, 192K bss, 5288K reserved)
[    0.000000] NR_IRQS:256
[    0.036000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[    0.040000] pid_max: default: 32768 minimum: 301
[    0.044000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.048000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.060000] NET: Registered protocol family 16
[    0.068000] registering PCI controller with io_map_base unset
[    0.072000] registering PCI controller with io_map_base unset
[    0.088000] PCI host bridge to bus 0000:00
[    0.092000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.096000] pci_bus 0000:00: root bus resource [io  0x8000000-0x8007fff]
[    0.100000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.104000] pci 0000:00:01.0: [14e4:a8d6] type 00 class 0x028000
[    0.104000] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x00003fff]
[    0.108000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.108000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30003fff]
[    0.112000] PCI host bridge to bus 0000:01
[    0.116000] pci_bus 0000:01: root bus resource [mem 0x38000000-0x3fffffff]
[    0.120000] pci_bus 0000:01: root bus resource [io  0x8008000-0x800ffff]
[    0.124000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[    0.128000] pci 0000:01:1e.0: [14e4:6358] type 02 class 0x060700
[    0.128000] pci 0000:01:1e.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.132000] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 05
[    0.132000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 05
[    0.132000] pci 0000:01:1e.0: BAR 10: assigned [mem 0x38000000-0x3fffffff]
[    0.136000] pci 0000:01:1e.0: BAR 7: assigned [io  0x8008000-0x80080ff]
[    0.140000] pci 0000:01:1e.0: BAR 8: assigned [io  0x8008400-0x80084ff]
[    0.144000] pci 0000:01:1e.0: CardBus bridge to [bus 02-05]
[    0.148000] pci 0000:01:1e.0:   bridge window [io  0x8008000-0x80080ff]
[    0.152000] pci 0000:01:1e.0:   bridge window [io  0x8008400-0x80084ff]
[    0.156000] pci 0000:01:1e.0:   bridge window [mem 0x38000000-0x3fffffff]
[    0.160000] Switched to clocksource MIPS
[    0.164000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[    0.196000] ssb: Found chip with id 0xA8D6, rev 0x00 and package 0x08
[    0.204000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x1E, vendor 0x4243)
[    0.204000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x10, vendor 0x4243)
[    0.204000] ssb: Core 2 found: PCI (cc 0x804, rev 0x0E, vendor 0x4243)
[    0.240000] ssb: WARNING: Using fallback SPROM failed (err -2)
[    0.244000] ssb: WARNING: Invalid SPROM CRC (corrupt SPROM)
[    0.252000] ssb: Unsupported SPROM revision 255 detected. Will extract v1
[    0.280000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
[    0.288000] NET: Registered protocol family 2
[    0.296000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.304000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.308000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.316000] TCP: reno registered
[    0.320000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.328000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.332000] NET: Registered protocol family 1
[    0.340000] PCI: CLS 0 bytes, default 16
[    0.340000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.348000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.356000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.364000] msgmni has been set to 53
[    0.372000] io scheduler noop registered
[    0.376000] io scheduler deadline registered (default)
[    0.384000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10, base_baud = 1562500) is a bcm63xx_uart
[    0.392000] console [ttyS0] enabled
[    0.400000] bootconsole [early0] disabled
[    0.408000] 1e000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022c9
[    0.420000] 1e000000.nor: Found an alias at 0x800000 for the chip at 0x0
[    0.420000] 1e000000.nor: Found an alias at 0x1000000 for the chip at 0x0
[    0.420000] 1e000000.nor: Found an alias at 0x1800000 for the chip at 0x0
[    0.420000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.424000]   Amd/Fujitsu Extended Query version 1.1.
[    0.432000] 1e000000.nor: Swapping erase regions for top-boot CFI table.
[    0.436000] number of CFI chips: 1
[    0.440000] bcm63xxpart: CFE boot tag found with version 6 and board type AW4139
[    0.448000] 5 bcm63xxpart partitions found on MTD device 1e000000.nor
[    0.456000] Creating 5 MTD partitions on "1e000000.nor":
[    0.460000] 0x000000000000-0x000000010000 : "CFE"
[    0.468000] 0x000000010100-0x00000012ab9e : "kernel"
[    0.476000] 0x00000012ab9e-0x0000003f0000 : "rootfs"
[    0.484000] mtd: device 2 (rootfs) set to be root filesystem
[    0.488000] 1 squashfs-split partitions found on MTD device rootfs
[    0.496000] 0x000000350000-0x0000003f0000 : "rootfs_data"
[    0.504000] 0x000000010000-0x0000003f0000 : "linux"
[    0.512000] 0x0000003f0000-0x000000400000 : "nvram"
[    0.520000] bcm63xx-spi bcm63xx-spi: at 0xfffe0800 (irq 9, FIFOs size 542)
[    0.556000] libphy: bcm63xx_enet MII bus: probed
[    0.560000] bcm63xx_enet bcm63xx_enet.1: attached PHY at address 0 [Generic PHY]
[    0.568000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.580000] TCP: cubic registered
[    0.584000] NET: Registered protocol family 17
[    0.588000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.600000] Bridge firewalling registered
[    0.604000] 8021q: 802.1Q VLAN Support v1.8
[    0.624000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.652000] Freeing unused kernel memory: 1304K (8035a000 - 804a0000)
[    2.416000] init: Console is alive
[    2.420000] init: - watchdog -
[    4.476000] init: - preinit -
[    5.412000] random: procd urandom read with 20 bits of entropy available
[    9.088000] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[    9.152000] procd: - early -
[    9.156000] procd: - watchdog -
[   10.200000] procd: - ubus -
[   11.212000] procd: - init -
[   13.292000] NET: Registered protocol family 10
[   13.308000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   13.336000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[   13.344000] Backport generated by backports.git backports-20150129-0-gdd4a670
[   13.360000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   13.384000] nf_conntrack version 0.5.0 (449 buckets, 1796 max)
[   13.460000] xt_time: kernel timezone is -0000
[   13.512000] cfg80211: Calling CRDA to update world regulatory domain
[   13.572000] cfg80211: World regulatory domain updated:
[   13.576000] cfg80211:  DFS Master region: unset
[   13.580000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   13.592000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   13.600000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   13.608000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   13.616000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   13.624000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   13.636000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   13.644000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   13.652000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   13.776000] PPP generic driver version 2.4.2
[   13.784000] NET: Registered protocol family 24
[   13.844000] b43-phy0: Broadcom 43222 WLAN found (core revision 16)
[   13.884000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6
[   13.888000] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2056, Revision 6, Version 0
[   13.908000] Broadcom 43xx driver loaded [ Features: PNL ]
[   14.100000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   21.828000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   28.304000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   28.328000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   28.332000] jffs2_build_filesystem(): erasing all blocks after the end marker...
[   31.300000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   31.324000] device eth0.1 entered promiscuous mode
[   31.332000] device eth0 entered promiscuous mode
[   31.360000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   33.044000] random: nonblocking pool is initialized
[   34.084000] done.
[   34.088000] jffs2: notice: (776) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
root@OpenWrt:/#

logread:

root@OpenWrt:/# logread
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.108000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30003fff]
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.112000] PCI host bridge to bus 0000:01
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.116000] pci_bus 0000:01: root bus resource [mem 0x38000000-0x3fffffff]
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.120000] pci_bus 0000:01: root bus resource [io  0x8008000-0x800ffff]
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.124000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
Tue Mar  1 09:19:33 2016 kern.debug kernel: [    0.128000] pci 0000:01:1e.0: [14e4:6358] type 02 class 0x060700
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.128000] pci 0000:01:1e.0: bridge configuration invalid ([bus 00-00]), reconfiguring
Tue Mar  1 09:19:33 2016 kern.debug kernel: [    0.132000] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 05
Tue Mar  1 09:19:33 2016 kern.debug kernel: [    0.132000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 05
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.132000] pci 0000:01:1e.0: BAR 10: assigned [mem 0x38000000-0x3fffffff]
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.136000] pci 0000:01:1e.0: BAR 7: assigned [io  0x8008000-0x80080ff]
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.140000] pci 0000:01:1e.0: BAR 8: assigned [io  0x8008400-0x80084ff]
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.144000] pci 0000:01:1e.0: CardBus bridge to [bus 02-05]
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.148000] pci 0000:01:1e.0:   bridge window [io  0x8008000-0x80080ff]
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.152000] pci 0000:01:1e.0:   bridge window [io  0x8008400-0x80084ff]
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.156000] pci 0000:01:1e.0:   bridge window [mem 0x38000000-0x3fffffff]
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.160000] Switched to clocksource MIPS
Tue Mar  1 09:19:33 2016 kern.warn kernel: [    0.164000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.196000] ssb: Found chip with id 0xA8D6, rev 0x00 and package 0x08
Tue Mar  1 09:19:33 2016 kern.debug kernel: [    0.204000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x1E, vendor 0x4243)
Tue Mar  1 09:19:33 2016 kern.debug kernel: [    0.204000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x10, vendor 0x4243)
Tue Mar  1 09:19:33 2016 kern.debug kernel: [    0.204000] ssb: Core 2 found: PCI (cc 0x804, rev 0x0E, vendor 0x4243)
Tue Mar  1 09:19:33 2016 kern.warn kernel: [    0.240000] ssb: WARNING: Using fallback SPROM failed (err -2)
Tue Mar  1 09:19:33 2016 kern.warn kernel: [    0.244000] ssb: WARNING: Invalid SPROM CRC (corrupt SPROM)
Tue Mar  1 09:19:33 2016 kern.warn kernel: [    0.252000] ssb: Unsupported SPROM revision 255 detected. Will extract v1
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.280000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.288000] NET: Registered protocol family 2
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.296000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.304000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.308000] TCP: Hash tables configured (established 1024 bind 1024)
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.316000] TCP: reno registered
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.320000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.328000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.332000] NET: Registered protocol family 1
Tue Mar  1 09:19:33 2016 kern.debug kernel: [    0.340000] PCI: CLS 0 bytes, default 16
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.340000] futex hash table entries: 256 (order: -1, 3072 bytes)
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.348000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.356000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.364000] msgmni has been set to 53
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.372000] io scheduler noop registered
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.376000] io scheduler deadline registered (default)
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.384000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10, base_baud = 1562500) is a bcm63xx_uart
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.392000] console [ttyS0] enabled
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.400000] bootconsole [early0] disabled
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.408000] 1e000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022c9
Tue Mar  1 09:19:33 2016 kern.debug kernel: [    0.420000] 1e000000.nor: Found an alias at 0x800000 for the chip at 0x0
Tue Mar  1 09:19:33 2016 kern.debug kernel: [    0.420000] 1e000000.nor: Found an alias at 0x1000000 for the chip at 0x0
Tue Mar  1 09:19:33 2016 kern.debug kernel: [    0.420000] 1e000000.nor: Found an alias at 0x1800000 for the chip at 0x0
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.420000] Amd/Fujitsu Extended Query Table at 0x0040
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.424000]   Amd/Fujitsu Extended Query version 1.1.
Tue Mar  1 09:19:33 2016 kern.warn kernel: [    0.432000] 1e000000.nor: Swapping erase regions for top-boot CFI table.
Tue Mar  1 09:19:33 2016 kern.notice kernel: [    0.436000] number of CFI chips: 1
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.440000] bcm63xxpart: CFE boot tag found with version 6 and board type AW4139
Tue Mar  1 09:19:33 2016 kern.notice kernel: [    0.448000] 5 bcm63xxpart partitions found on MTD device 1e000000.nor
Tue Mar  1 09:19:33 2016 kern.notice kernel: [    0.456000] Creating 5 MTD partitions on "1e000000.nor":
Tue Mar  1 09:19:33 2016 kern.notice kernel: [    0.460000] 0x000000000000-0x000000010000 : "CFE"
Tue Mar  1 09:19:33 2016 kern.notice kernel: [    0.468000] 0x000000010100-0x00000012ab9e : "kernel"
Tue Mar  1 09:19:33 2016 kern.notice kernel: [    0.476000] 0x00000012ab9e-0x0000003f0000 : "rootfs"
Tue Mar  1 09:19:33 2016 kern.notice kernel: [    0.484000] mtd: device 2 (rootfs) set to be root filesystem
Tue Mar  1 09:19:33 2016 kern.notice kernel: [    0.488000] 1 squashfs-split partitions found on MTD device rootfs
Tue Mar  1 09:19:33 2016 kern.notice kernel: [    0.496000] 0x000000350000-0x0000003f0000 : "rootfs_data"
Tue Mar  1 09:19:33 2016 kern.notice kernel: [    0.504000] 0x000000010000-0x0000003f0000 : "linux"
Tue Mar  1 09:19:33 2016 kern.notice kernel: [    0.512000] 0x0000003f0000-0x000000400000 : "nvram"
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.520000] bcm63xx-spi bcm63xx-spi: at 0xfffe0800 (irq 9, FIFOs size 542)
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.556000] libphy: bcm63xx_enet MII bus: probed
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.560000] bcm63xx_enet bcm63xx_enet.1: attached PHY at address 0 [Generic PHY]
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.568000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.580000] TCP: cubic registered
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.584000] NET: Registered protocol family 17
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.588000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
Tue Mar  1 09:19:33 2016 kern.notice kernel: [    0.600000] Bridge firewalling registered
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.604000] 8021q: 802.1Q VLAN Support v1.8
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.624000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Tue Mar  1 09:19:33 2016 kern.info kernel: [    0.652000] Freeing unused kernel memory: 1304K (8035a000 - 804a0000)
Tue Mar  1 09:19:33 2016 user.info kernel: [    2.416000] init: Console is alive
Tue Mar  1 09:19:33 2016 user.info kernel: [    2.420000] init: - watchdog -
Tue Mar  1 09:19:33 2016 user.info kernel: [    4.476000] init: - preinit -
Tue Mar  1 09:19:33 2016 kern.notice kernel: [    5.416000] random: procd urandom read with 20 bits of entropy available
Tue Mar  1 09:19:33 2016 kern.info kernel: [    7.840000] eth0: link UP - 100/full - flow control rx&tx
Tue Mar  1 09:19:33 2016 kern.notice kernel: [    9.108000] jffs2: notice: (234) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Tue Mar  1 09:19:33 2016 user.info kernel: [    9.124000] mount_root: switching to jffs2 overlay
Tue Mar  1 09:19:33 2016 user.info kernel: [    9.192000] procd: - early -
Tue Mar  1 09:19:33 2016 user.info kernel: [    9.196000] procd: - watchdog -
Tue Mar  1 09:19:33 2016 kern.info kernel: [    9.928000] eth0: link DOWN
Tue Mar  1 09:19:33 2016 user.info kernel: [   10.220000] procd: - ubus -
Tue Mar  1 09:19:33 2016 user.info kernel: [   11.232000] procd: - init -
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.248000] NET: Registered protocol family 10
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.264000] ip6_tables: (C) 2000-2006 Netfilter Core Team
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.296000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.304000] Backport generated by backports.git backports-20150129-0-gdd4a670
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.316000] ip_tables: (C) 2000-2006 Netfilter Core Team
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.344000] nf_conntrack version 0.5.0 (449 buckets, 1796 max)
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.420000] xt_time: kernel timezone is -0000
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.472000] cfg80211: Calling CRDA to update world regulatory domain
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.528000] cfg80211: World regulatory domain updated:
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.532000] cfg80211:  DFS Master region: unset
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.536000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.548000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.556000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.564000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.572000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.580000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.592000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.600000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.608000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.728000] PPP generic driver version 2.4.2
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.736000] NET: Registered protocol family 24
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.796000] b43-phy0: Broadcom 43222 WLAN found (core revision 16)
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.836000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.840000] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2056, Revision 6, Version 0
Tue Mar  1 09:19:33 2016 kern.info kernel: [   13.860000] Broadcom 43xx driver loaded [ Features: PNL ]
Tue Mar  1 09:19:33 2016 kern.debug kernel: [   14.052000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Tue Mar  1 09:19:35 2016 kern.info kernel: [   20.172000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Tue Mar  1 09:19:35 2016 user.emerg syslog: Failed to connect to the switch. Use the "list" command to see which switches are available.
Tue Mar  1 09:19:37 2016 kern.info kernel: [   22.672000] eth0: link UP - 100/full - flow control rx&tx
Tue Mar  1 09:19:37 2016 kern.info kernel: [   22.680000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Tue Mar  1 09:19:40 2016 authpriv.info dropbear[652]: Not backgrounding
Tue Mar  1 09:19:43 2016 daemon.info procd: - init complete -
Tue Mar  1 09:19:44 2016 kern.info kernel: [   28.792000] device eth0.1 entered promiscuous mode
Tue Mar  1 09:19:44 2016 kern.info kernel: [   28.796000] device eth0 entered promiscuous mode
Tue Mar  1 09:19:44 2016 kern.info kernel: [   28.808000] br-lan: port 1(eth0.1) entered forwarding state
Tue Mar  1 09:19:44 2016 kern.info kernel: [   28.816000] br-lan: port 1(eth0.1) entered forwarding state
Tue Mar  1 09:19:44 2016 daemon.notice netifd: Interface 'lan' is enabled
Tue Mar  1 09:19:44 2016 daemon.notice netifd: Interface 'lan' is setting up now
Tue Mar  1 09:19:44 2016 daemon.notice netifd: Interface 'lan' is now up
Tue Mar  1 09:19:44 2016 daemon.notice netifd: Interface 'loopback' is enabled
Tue Mar  1 09:19:44 2016 daemon.notice netifd: Interface 'loopback' is setting up now
Tue Mar  1 09:19:44 2016 daemon.notice netifd: Interface 'loopback' is now up
Tue Mar  1 09:19:44 2016 daemon.notice netifd: Network device 'eth0' link is up
Tue Mar  1 09:19:44 2016 daemon.notice netifd: Bridge 'br-lan' link is up
Tue Mar  1 09:19:44 2016 daemon.notice netifd: Interface 'lan' has link connectivity
Tue Mar  1 09:19:44 2016 daemon.notice netifd: VLAN 'eth0.1' link is up
Tue Mar  1 09:19:44 2016 daemon.notice netifd: Network device 'lo' link is up
Tue Mar  1 09:19:44 2016 daemon.notice netifd: Interface 'loopback' has link connectivity
Tue Mar  1 09:19:44 2016 kern.info kernel: [   29.052000] eth0: link UP - 100/full - flow control rx&tx
Tue Mar  1 09:19:45 2016 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Tue Mar  1 09:19:46 2016 kern.info kernel: [   30.820000] br-lan: port 1(eth0.1) entered forwarding state
Tue Mar  1 09:19:46 2016 daemon.notice netifd: radio0 (730): Configuration file: /var/run/hostapd-phy0.conf
Tue Mar  1 09:19:46 2016 daemon.notice netifd: radio0 (730): nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Tue Mar  1 09:19:46 2016 daemon.notice netifd: radio0 (730): nl80211 driver initialization failed.
Tue Mar  1 09:19:46 2016 daemon.notice netifd: radio0 (730): wlan0: interface state UNINITIALIZED->DISABLED
Tue Mar  1 09:19:46 2016 daemon.notice netifd: radio0 (730): wlan0: AP-DISABLED
Tue Mar  1 09:19:46 2016 daemon.notice netifd: radio0 (730): hostapd_free_hapd_data: Interface wlan0 wasn't started
Tue Mar  1 09:19:46 2016 daemon.notice netifd: radio0 (730): cat: can't open '/var/run/wifi-phy0.pid': No such file or directory
Tue Mar  1 09:19:47 2016 daemon.notice netifd: radio0 (730): Command failed: Invalid argument
Tue Mar  1 09:19:47 2016 daemon.notice netifd: radio0 (730): Device setup failed: HOSTAPD_START_FAILED
Tue Mar  1 09:19:47 2016 kern.notice kernel: [   32.576000] random: nonblocking pool is initialized
Tue Mar  1 09:19:51 2016 daemon.info dnsmasq[875]: started, version 2.73 cachesize 150
Tue Mar  1 09:19:51 2016 daemon.info dnsmasq[875]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC loop-detect inotify
Tue Mar  1 09:19:51 2016 daemon.info dnsmasq[875]: DNS service limited to local subnets
Tue Mar  1 09:19:51 2016 daemon.info dnsmasq-dhcp[875]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Tue Mar  1 09:19:51 2016 daemon.info dnsmasq[875]: using local addresses only for domain lan
Tue Mar  1 09:19:51 2016 daemon.warn dnsmasq[875]: no servers found in /tmp/resolv.conf.auto, will retry
Tue Mar  1 09:19:51 2016 daemon.info dnsmasq[875]: read /etc/hosts - 1 addresses
Tue Mar  1 09:19:51 2016 daemon.info dnsmasq[875]: read /tmp/hosts/dhcp - 1 addresses
Tue Mar  1 09:19:51 2016 daemon.info dnsmasq-dhcp[875]: read /etc/ethers - 0 addresses
Tue Mar  1 09:20:18 2016 kern.info kernel: [   63.208000] eth0: link DOWN
Tue Mar  1 09:20:18 2016 kern.info kernel: [   63.208000] br-lan: port 1(eth0.1) entered disabled state
Tue Mar  1 09:20:18 2016 daemon.notice netifd: Network device 'eth0' link is down
Tue Mar  1 09:20:18 2016 daemon.notice netifd: VLAN 'eth0.1' link is down
Tue Mar  1 09:20:19 2016 daemon.notice netifd: Bridge 'br-lan' link is down
Tue Mar  1 09:20:19 2016 daemon.notice netifd: Interface 'lan' has link connectivity loss
Tue Mar  1 09:20:22 2016 daemon.notice netifd: Network device 'eth0' link is up
Tue Mar  1 09:20:22 2016 kern.info kernel: [   67.208000] eth0: link UP - 100/full - flow control rx&tx
Tue Mar  1 09:20:22 2016 kern.info kernel: [   67.212000] br-lan: port 1(eth0.1) entered forwarding state
Tue Mar  1 09:20:22 2016 kern.info kernel: [   67.220000] br-lan: port 1(eth0.1) entered forwarding state
Tue Mar  1 09:20:22 2016 daemon.notice netifd: VLAN 'eth0.1' link is up
Tue Mar  1 09:20:22 2016 daemon.notice netifd: Bridge 'br-lan' link is up
Tue Mar  1 09:20:22 2016 daemon.notice netifd: Interface 'lan' has link connectivity
Tue Mar  1 09:20:24 2016 kern.info kernel: [   69.224000] br-lan: port 1(eth0.1) entered forwarding state
Tue Mar  1 09:22:58 2016 kern.info kernel: [  223.212000] eth0: link DOWN
Tue Mar  1 09:22:58 2016 kern.info kernel: [  223.212000] br-lan: port 1(eth0.1) entered disabled state
Tue Mar  1 09:22:58 2016 daemon.notice netifd: Network device 'eth0' link is down
Tue Mar  1 09:22:58 2016 daemon.notice netifd: VLAN 'eth0.1' link is down
Tue Mar  1 09:22:59 2016 daemon.notice netifd: Bridge 'br-lan' link is down
Tue Mar  1 09:22:59 2016 daemon.notice netifd: Interface 'lan' has link connectivity loss
Tue Mar  1 09:23:07 2016 daemon.notice netifd: Network device 'eth0' link is up
Tue Mar  1 09:23:07 2016 kern.info kernel: [  232.212000] eth0: link UP - 100/full - flow control off
Tue Mar  1 09:23:07 2016 kern.info kernel: [  232.216000] br-lan: port 1(eth0.1) entered forwarding state
Tue Mar  1 09:23:07 2016 kern.info kernel: [  232.224000] br-lan: port 1(eth0.1) entered forwarding state
Tue Mar  1 09:23:07 2016 daemon.notice netifd: VLAN 'eth0.1' link is up
Tue Mar  1 09:23:07 2016 daemon.notice netifd: Bridge 'br-lan' link is up
Tue Mar  1 09:23:07 2016 daemon.notice netifd: Interface 'lan' has link connectivity
Tue Mar  1 09:23:09 2016 kern.info kernel: [  234.228000] br-lan: port 1(eth0.1) entered forwarding state
root@OpenWrt:/#

Link state changed:

[ 1230.220000] br-lan: port 1(eth0.1) entered disabled state
[ 1285.216000] eth0: link UP - 100/full - flow control rx&tx
[ 1285.220000] br-lan: port 1(eth0.1) entered forwarding state
[ 1285.228000] br-lan: port 1(eth0.1) entered forwarding state
[ 1287.232000] br-lan: port 1(eth0.1) entered forwarding state

LEN blinking when data received (try to ping, LED blinking), bot no response. When I look into stats on Windows, I can see only Sent packets and no Received...
Other ports (expect eth0.1) does not recognize when I plug/unplug cable. LED for current port blink again (maybe connected to HW?), link in another port is not reachable too.


Router Power LED is RED, so maybe some problem?
When try to enable wifi:

uci set wireless.@wifi-device[0].disabled=0; uci commit wireless; wifi

root@OpenWrt:/# uci show wireless | grep disabled
wireless.radio0.disabled='0'

root@OpenWrt:/# wifi up
root@OpenWrt:/#

root@OpenWrt:/# cat /etc/config/wireless

config wifi-device 'radio0'
        option type 'mac80211'
        option channel '11'
        option hwmode '11g'
        option path 'pci0000:00/0000:00:01.0/ssb0:0'
        option disabled '0'

config wifi-iface
        option device 'radio0'
        option network 'lan'
        option mode 'ap'
        option ssid 'OpenWrt'
        option encryption 'none'

No LED changed and wifi not broadcast (not able to see on mobile phone)

(Last edited by mtrakal on 26 Sep 2017, 01:41)

The discussion might have continued from here.