OpenWrt Forum Archive

Topic: wr 841n v11 (EU) router down!!!

The content of this topic has been archived on 9 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

Post #1
PK34
13 Oct 2017, 16:51

Hi everbody i need some help
who can help me? than you so much

i have a router wr 841 n eu v11

i want to software change openwrt or dd wrt but software locked


i am first open locked software a member editing software later update webif tp link

but luci dont work then..

i want to make it dd wrt i will upload and update all commands ethernet cable

now my router down all leds opening then only ethernet led opening then closing all leds later
again opening....

i have a serial cable but i cannot connect cable my router motherboard?

t.u.

Post #2
PK34
18 Oct 2017, 02:17

I DONT UPDATE SERIAL MY ROUTER
WHAT IS PROBLEM PLS HELP

Retry count exceeded; starting again
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... ERROR: LzmaDecode.c, 543

Decoding error = 1
LZMA ERROR 1 - must RESET board to recover▒

U-Boot 1.1.4 (Jun 16 2015 - 14:12:19)

ap143-2.0 - Honey Bee 2.0

DRAM:  32 MB
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x16
flash size 4MB, sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ---->S27 PHY*
S27 reg init
: cfg1 0x800c0000 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
Honey Bee ---->  MAC 1 S27 PHY *
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x5ebda100
is_auto_upload_firmware=1
enet1 port0 up
dup 1 speed 1000
Using eth1 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.86
Filename 'wr841nv11_tp_recovery.bin'.
Load address: 0x80800000
Loading: T T T
Retry count exceeded; starting again
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... ERROR: LzmaDecode.c, 543

Decoding error = 1
LZMA ERROR 1 - must RESET board to recover▒

U-Boot 1.1.4 (Jun 16 2015 - 14:12:19)

ap143-2.0 - Honey Bee 2.0

DRAM:  32 MB
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x16
flash size 4MB, sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ---->S27 PHY*
S27 reg init
: cfg1 0x800c0000 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
Honey Bee ---->  MAC 1 S27 PHY *
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x5ebda100
is_auto_upload_firmware=0
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... ERROR: LzmaDecode.c, 543

Decoding error = 1
LZMA ERROR 1 - must RESET board to recover▒

U-Boot 1.1.4 (Jun 16 2015 - 14:12:19)

ap143-2.0 - Honey Bee 2.0

DRAM:  32 MB
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x16
flash size 4MB, sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ---->S27 PHY*
S27 reg init
: cfg1 0x800c0000 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
Honey Bee ---->  MAC 1 S27 PHY *
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x5ebda100
is_auto_upload_firmware=0
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... ERROR: LzmaDecode.c, 543

Decoding error = 1
LZMA ERROR 1 - must RESET board to recover▒

U-Boot 1.1.4 (Jun 16 2015 - 14:12:19)

ap143-2.0 - Honey Bee 2.0

DRAM:  32 MB
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x16
flash size 4MB, sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ---->S27 PHY*
S27 reg init
: cfg1 0x800c0000 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
Honey Bee ---->  MAC 1 S27 PHY *
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x5ebda100
is_auto_upload_firmware=1
enet1 port0 up
dup 1 speed 1000
Using eth1 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.86
Filename 'wr841nv11_tp_recovery.bin'.
Load address: 0x80800000
Loading: T T T
Retry count exceeded; starting again
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... ERROR: LzmaDecode.c, 543

Decoding error = 1
LZMA ERROR 1 - must RESET board to recover▒

U-Boot 1.1.4 (Jun 16 2015 - 14:12:19)

ap143-2.0 - Honey Bee 2.0

DRAM:  32 MB
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x16
flash size 4MB, sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ---->S27 PHY*
S27 reg init
: cfg1 0x800c0000 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
Honey Bee ---->  MAC 1 S27 PHY *
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x5ebda100
is_auto_upload_firmware=0
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... ERROR: LzmaDecode.c, 543

Decoding error = 1
LZMA ERROR 1 - must RESET board to recover

The discussion might have continued from here.