Thank for the info.
I've run make with "-i" parameter and it has compiled it to the end.
But, now I have another problem with the compiled file and the one downloaded from openwrt.org side.
I get kernel panic wile running squashfs from the router.
ROM VER: 1.0.3
CFG 01
Read EEPROMX
X
U-Boot 2013.10-openwrt4 (Dec 18 2017 - 21:58:48) ARV752DPW
Board: Arcadyan ARV752DPW
SoC: Lantiq Danube-S v1.5
CPU: 333.333 MHz
IO: 166.667 MHz
BUS: 83.333 MHz
BOOT: NOR
DRAM: 64 MiB
Flash: 8 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: Board Net Initialization Failed
ltq-eth
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at b0040000 ...
Image Name: MIPS OpenWrt Linux-3.18.23
Created: 2016-02-02 12:41:47 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1530227 Bytes = 1.5 MiB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.18.23 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r47269) ) #1 Sun 6
[ 0.000000] SoC: Danube rev 1.5
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019641 (MIPS 24KEc)
[ 0.000000] MIPS: machine is ARV752DPW - Arcor 802
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=0007fd38
[ 0.000000] Readback ErrCtl register=0007fd38
[ 0.000000] Memory: 60144K/65536K available (3433K kernel code, 151K rwdata, 768K rodata, 172K init, 194K bss, 5392K reser)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 333MHz
[ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[ 0.040000] pid_max: default: 32768 minimum: 301
[ 0.044000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.048000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.056000] pinctrl core: initialized pinctrl subsystem
[ 0.064000] NET: Registered protocol family 16
[ 0.076000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.080000] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20
[ 0.088000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[ 0.092000] MEM 0x0000000018000000..0x0000000019ffffff
[ 0.096000] IO 0x000000001ae00000..0x000000001affffff
[ 0.112000] usbcore: registered new interface driver usbfs
[ 0.116000] usbcore: registered new interface driver hub
[ 0.120000] usbcore: registered new device driver usb
[ 0.124000] PCI host bridge to bus 0000:00
[ 0.128000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[ 0.132000] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 0.136000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.140000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[ 0.144000] Switched to clocksource MIPS
[ 0.148000] NET: Registered protocol family 2
[ 0.156000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.164000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.168000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.176000] TCP: reno registered
[ 0.180000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.184000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.192000] NET: Registered protocol family 1
[ 0.196000] gptu: totally 6 16-bit timers/counters
[ 0.200000] gptu: misc_register on minor 63
[ 0.204000] gptu: succeeded to request irq 126
[ 0.212000] gptu: succeeded to request irq 127
[ 0.216000] gptu: succeeded to request irq 128
[ 0.220000] gptu: succeeded to request irq 129
[ 0.224000] gptu: succeeded to request irq 130
[ 0.228000] gptu: succeeded to request irq 131
[ 0.240000] lantiq,vmmc 1f103000.vmmc: requested GPIO 465
[ 0.244000] lantiq,vmmc 1f103000.vmmc: reserved 1MB at 0x03a00000
[ 0.252000] ralink,eeprom ralink_eep: using RT2860.eeprom as eeprom
[ 0.260000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.268000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.276000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.304000] msgmni has been set to 117
[ 0.312000] io scheduler noop registered
[ 0.316000] io scheduler deadline registered (default)
[ 0.324000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[ 0.332000] console [ttyLTQ0] enabled
[ 0.332000] console [ttyLTQ0] enabled
[ 0.340000] bootconsole [early0] disabled
[ 0.340000] bootconsole [early0] disabled
[ 0.348000] lantiq nor flash device: 00800000 at 10000000
[ 0.352000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[ 0.360000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.368000] Amd/Fujitsu Extended Query version 1.1.
[ 0.372000] number of CFI chips: 1
[ 0.376000] 4 ofpart partitions found on MTD device ltq_nor
[ 0.380000] Creating 4 MTD partitions on "ltq_nor":
[ 0.384000] 0x000000000000-0x000000010000 : "uboot"
[ 0.392000] 0x000000010000-0x000000020000 : "uboot_env"
[ 0.396000] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.540000] 0x0000007f0000-0x000000800000 : "board_config"
[ 0.572000] libphy: ltq_mii: probed
[ 0.668000] Registering RTL8306SDM switch with Chip ID: 0x5988, version: 0x0000
[ 0.672000] eth0: attached PHY [Realtek RTL8306S] (phy_addr=1e180000.etop-ff:00, irq=-1)
[ 0.684000] wdt 1f8803f0.watchdog: Init done
[ 0.692000] TCP: cubic registered
[ 0.692000] NET: Registered protocol family 17
[ 0.696000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter.
[ 0.708000] Bridge firewalling registered
[ 0.712000] 8021q: 802.1Q VLAN Support v1.8
[ 0.724000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[ 0.728000] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[ 0.736000] Please append a correct "root=" boot option; here are the available partitions:
[ 0.744000] 1f00 64 mtdblock0 (driver?)
[ 0.748000] 1f01 64 mtdblock1 (driver?)
[ 0.756000] 1f02 8000 mtdblock2 (driver?)
[ 0.760000] 1f03 64 mtdblock3 (driver?)
[ 0.764000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 0.764000] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 33.088000] random: nonblocking pool is initialized
