Iv just got Dlink DIR-605L HW:B (EU) 802.11n Wireless Router
I did not find anything related on OpenWRT/LEDE pages and github for this device so I will post here what I found
RTL8196E its LEXRA processor MIPS wariant
RTL8192ER WiFi chip
4mb flash
em63a165ts-6g RAM 4 Banks of 4M word x 16
Booting...
OK
OK
---RealTek(RTL8196E-kld) version v6.0.4e(2013.02.22-18:00+0800) [16bit](380MHz)
Jump to image start=0x80500000...
decompressing kernel:
Uncompressing Linux... done, booting the kernel.
done decompressing kernel.
Creating 4 MTD partitions on "Physically mapped flash":
0x00000000-0x000e0000 : "boot+cfg+linux"
master size 0x004000000x000e0000-0x00370000 : "root fs"
master size 0x004000000x00370000-0x00380000 : "webpage"
master size 0x004000000x00380000-0x00400000 : "mydlink"
master size 0x00400000Realtek WLAN driver - version 1.6 (2013-02-21)
Adaptivity function - version 7.1
#######################################################
SKB_BUF_SIZE=2048 MAX_SKB_NUM=400
#######################################################
init started: BusyBox v1.01 (2015.05.08-01:48+0000) multi-call binary
Starting pid 9, console /dev/ttyS0: '/bin/sh'
BusyBox v1.01 (2015.05.08-09:16+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
61
Init Start...
mkdir: Cannot create directory `/var/system': File exists
iwpriv wlan0 set_mib tx_pwr_ctrl=0
set 615 wlan channel
iwpriv wlan0 write_mem dw,b8000048,1,4026d832
Init bridge interface...
new_nbp GBP_ATOMIC ...
[PHY_REG_8192Emp]
[AGC_TAB_8192Emp]
[RadioA_8192Emp]
[RadioB_8192Emp]
new_nbp GBP_ATOMIC ...
Init Wlan application...
WiFi Simple Config v2.7-wps2.0 (2015.05.08-01:54+0000).
Init WAN Interface...
udhcpc -i eth1 -p /etc/udhcpc/udhcpc-eth1.pid -s /usr/share/udhcpc/eth1.sh -I 0 -a 30 -h DIR-605L &
MiniIGD v1.08 (2015.05.05-03:10+0000).
0DevInfo.txt text mode!
hard ver isB2
341
boa: server version Boa/0.94.14rc21
boa: server built Dec 3 2015 at 09:36:22.
boa: starting server pid=340, port 80
killall: mydlink-watch-dog.sh: no process killed
killall: signalc: no process killed
killall: tsa: no process killed
opt.local stop ok.
opt.local start ok.
384
# # cat proc/cpuinfo
system type : Philips Nino
processor : 0
cpu model : R3000 V0.0
BogoMIPS : 379.28
wait instruction : yes
microsecond timers : no
tlb_entries : 32
extra interrupt vector : no
hardware watchpoint : no
VCED exceptions : not available
VCEI exceptions : not available
ll emulations : 0
sc emulations : 0# cat /proc/mtd
dev: size erasesize name
mtd0: 000e0000 00001000 "boot+cfg+linux"
mtd1: 00290000 00001000 "root fs"
mtd2: 00010000 00001000 "webpage"
mtd3: 00080000 00001000 "mydlink"Hitting "ESC" after power on there is mod for boot from ram and enc
<RealTek>?
----------------- COMMAND MODE HELP ------------------
HELP (?) : Print this help message
SIG: SIG <type><sig>
SIGR: Display signature and flag
LOADADDR: <Load Address>
J: Jump to <TargetAddress>
FLR: FLR <dst><src><length>
FLW <dst_ROM_offset><src_RAM_addr><length_Byte> <SPI cnt#>: Write offset-data to SPI from RAM
MDIOR: MDIOR <phyid> <reg>
MDIOW: MDIOW <phyid> <reg> <data>
PHYR: PHYR <PHYID><reg>
PHYW: PHYW <PHYID><reg><data>
PORT1: port 1 patch for FT2
<RealTek>
I have seen similar hw spec. devices supported from OpenWrt/LEDE it should not be too dificult to add this, I dont have any knowlage how to that bum I have the will to test it boot from ram just not sure how to use <RealTek> CLI
Cheers
(Last edited by vido on 26 Dec 2017, 01:21)