OpenWrt Forum Archive

Post #1

SyncRo

9 Feb 2007, 01:07

1st off all Kamikaze compiled and runs on my ASUS WL500gP but it could be more better, why?

I'm using the r6272 out auf svn.

I enabled some more packages beside the defaults.

After booting I get a kernel oops in my dmesg but the machine works and the network is working properly

hub 1-0:1.0: 4 ports detected
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
Data bus error, epc == 8010e0e4, ra == 80014b50
Oops[#1]:
Cpu 0
$ 0   : 00000000 10009c00 81929000 00000001
$ 4   : 81929000 fffdbea2 000000b6 81929000
$ 8   : 0000000b 00000000 00000000 7fc83ea2
$12   : 00000001 0af98234 00000001 2abdee84
$16   : 000000b6 000000b6 7fc83ea2 81929000
$20   : 812b0c80 812b0cb4 81929000 00000000
$24   : 00000006 800159e0
$28   : 802ea000 802ebdf8 81258148 80014b50
Hi    : 000002f7
Lo    : 0002b99b
epc   : 8010e0e4     Tainted: P
ra    : 80014b50 Status: 10009c03    KERNEL EXL IE
Cause : 0000001c
PrId  : 00029006
Modules linked in: usb_storage sd_mod scsi_mod ehci_hcd ath_pci wlan_xauth wlan_wep wlan_tkip wlan_ccmp wlan_acl ath_rate_sample ath_hal(P) wlan_scan_sta wlan_scan_ap wlan ip_conntrack_tftp ip_nat_irc ip_conntrack_irc ip_nat_ftp ip_conntrack_ftp ppp_async crc_ccitt vfat fat nfs lockd sunrpc ext3 jbd ext2 cifs usbcore nls_base pppoe pppox ppp_generic slhc switch_robo switch_core diag
Process grep (pid: 711, threadinfo=802ea000, task=813c2998)
Stack : 812b0c80 812b0cb4 81929000 00000000 80069154 800690d0 81258148 812b0c80
        8023827c 81129be0 81c22ea2 000000b6 802ebe30 802ebe34 81038440 81272710
        000000b6 00000000 812b0c80 fffffff4 81929000 00001000 81258148 00000003
        00000000 800bbb98 00000c00 fffffffd 8105d180 802ebf18 00000000 00000003
        81258148 81929000 00000c00 fffffff4 8105d180 802ebf18 100091a8 800bc394
        ...
Call Trace:[<80069154>][<800690d0>][<800bbb98>][<800bc394>][<8006c0bc>][<8007d9b4>][<8007dd98>][<8006c30c>][<8006c23c>][<80012860>]

Code: 00064102  11000011  30d8000f <98a80000> 98a90004  24c6fff0  88a80003  88a90007  98aa0008
note: grep[711] exited with preempt_count 1

It seems that there are some problems with processes because top and ps are making some trouble, too:

ps produces the following:

Data bus error, epc == 8010e134, ra == 80014b50
Oops[#2]:
Cpu 0
$ 0   : 00000000 10009c00 8125b000 00000002
$ 4   : 8125b000 fffd9fab 0000000b 8125b000
$ 8   : 00000000 00000000 00000000 7f949fab
$12   : 00000001 0006d8b5 00000001 2abdee84
$16   : 0000000b 0000000b 7f949fab 8125b000
$20   : 8111ec60 8111ec94 8125b000 00000000
$24   : 00000003 800159e0
$28   : 8135e000 8135fdf8 80291858 80014b50
Hi    : 000000d0
Lo    : 000001b3
epc   : 8010e134     Tainted: P
ra    : 80014b50 Status: 10009c03    KERNEL EXL IE
Cause : 0000001c
PrId  : 00029006
Modules linked in: usb_storage sd_mod scsi_mod ehci_hcd ath_pci wlan_xauth wlan_wep wlan_tkip wlan_ccmp wlan_acl ath_rate_sample ath_hal(P) wlan_scan_sta wlan_scan_ap wlan ip_conntrack_tftp ip_nat_irc ip_conntrack_irc ip_nat_ftp ip_conntrack_ftp ppp_async crc_ccitt vfat fat nfs lockd sunrpc ext3 jbd ext2 cifs usbcore nls_base pppoe pppox ppp_generic slhc switch_robo switch_core diag
Process ps (pid: 861, threadinfo=8135e000, task=802b70c8)
Stack : 8111ec60 8111ec94 8125b000 00000000 80069154 800690d0 80291858 8111ec60
        8023827c 8131b640 8039afab 0000000b 8135fe30 8135fe34 81007340 8024d5c0
        0000000b 00000000 8111ec60 fffffff4 8125b000 00001000 80291858 00000001
        00409730 800bbb98 000003ff fffffffd 8125a8a0 8135ff18 00000000 00000001
        80291858 8125b000 000003ff fffffff4 8125a8a0 8135ff18 7fa86810 800bc394
        ...
Call Trace:[<80069154>][<800690d0>][<8024d5c0>][<800bbb98>][<800bc394>][<8007d9b4>][<8007dd98>][<8007cfb0>][<80012860>]

Code: 30d80003  1306000a  00000000 <98a80000> 88a80003  24a50004  24c6fffc  ac880000  14d8fffa
note: ps[861] exited with preempt_count 1

top runs too but I can not get out of it while using any key and no key is working!!

After starting the ASUS the connection to my ISP works as expected but after some more seconds connected I get a next device (ppp1) which get it's own IP and routing goes wrong.
If I kill this device:

ifconfig ppp1 down

routing works again

So I think I have something wrong in my settings or kamikaze does not recognize the current parameters of an ASUS WL500gP correctly, so please ask for further information, I will try to collect all needed stuff to solve these described problems.

The only changes I made to the default image beside password, ether, hosts, dnsmasq.conf and my local network settings (192.168.111.XXX) is the following.
I guessed it myself and it works

#### WAN configuration
config interface        wan
        option ifname   "eth0.1"
        option proto    pppoe
        option username BillGates@heaven.hell
        option password G1v3M3M0r3$5

(Last edited by SyncRo on 9 Feb 2007, 01:08)

Post #2

nial

30 Apr 2007, 13:37

SyncRo: Can you post your Kamikaze build containing audio drivers somwhere on the web. I have Wl500GP also, and would like to give it a try couase I still cannot compile my own image.

Post #3

SyncRo

2 May 2007, 23:01

Hey, I need no audio, so there wont be support and a module for me.

BTW: this post is one of my 1st trail kamikaze and it is very old, I just want to delete it because these problems do not exist anymore.

After a couple of weeks trying and then a couple of weeks doing nothing, now I have a build of kamikaze running and I have to read some stuff for configuration.

Post #4

dottout

7 May 2007, 20:59

hi, can you please post your firmware\config file somewhere? im going to try openwrt and Id like to have something to start from

Post #5

Tom

17 May 2007, 06:20

@dottout: Dont worry, just start with flashing a nightly build, then proceed and build kamikaze on your own with default values presented in menuconfig.