I was trying to update the wiki page for the rt-n66r but I never get the email confirmation. The serial settings are 115200, 8n1. The nice things about this router is that the serial port has pins and is clearly labeled. There is no need for a soldering iron on this router!
Here is the output from the stock rom. Also I am offering an asus rt-n66r to any developer to help get this in DD.
Decompressing...
Decompressing...done
CFE version 5.100.138.20 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: 五 1月 24 17:20:49 CST 2014 (yau@wireless-pub2)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.20
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes
CFE mem: 0x80700000 - 0x808358A0 (1267872)
Data: 0x8072F6B0 - 0x80732910 (12896)
BSS: 0x80732910 - 0x807338A0 (3984)
Heap: 0x807338A0 - 0x808338A0 (1048576)
Stack: 0x808338A0 - 0x808358A0 (8192)
Text: 0x80700000 - 0x8072F6B0 (194224)
Device eth0: hwaddr 10-C3-7B-xx-yy-zz, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Null Rescue Flag.
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: TFTP Server.
Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: ...... 3310368 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
start_kernel
Linux version 2.6.22.19 (root@asus) (gcc version 4.2.3) #1 Thu Feb 12 20:33:36 C ST 2015
CPU revision is: 00019749
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
memory: 08000000 @ 87fff000 (usable)
Built 1 zonelists. Total pages: 585216
Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 2048 (order: 11, 8192 bytes)
CPU: BCM5300 rev 1 pkg 0 at 600 MHz
Using 300.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 238608k/131068k available (2531k kernel code, 22572k reserved, 504k data , 196k init, 131072k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: Initializing host
PCI: Reset RC
PCI: Initializing host
PCI: Reset RC
PCI: Fixing up bus 0
PCI/PCIe coreunit 0 is set to bus 1.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
PCI/PCIe coreunit 1 is set to bus 2.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
PCI: Fixing up bus 2
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
highmem bounce pool size: 64 pages
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0xb8000300 (irq = 8) is a 16550A
serial8250: ttyS1 at MMIO 0xb8000400 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.18.3
PPTP driver version 0.8.5
Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x2000000 at 0x1c000000
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "pmon"
0x00040000-0x01fe0000 : "linux"
0x0016e474-0x019a0000 : "rootfs"
0x01fe0000-0x02000000 : "nvram"
0x01ee0000-0x01fe0000 : "jffs2"
Found an serial flash with 0 0KB blocks; total size 0MB
sflash: found no supported devices
dev_nvram_init: _nvram_init
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
u32 classifier
OLD policer on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (2048 buckets, 16384 max)
ipt_time loading
ip_tables: (C) 2000-2006 Netfilter Core Team
net/ipv4/netfilter/tomato_ct.c [Feb 12 2015 20:33:02]
NET: Registered protocol family 1
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 196k freed
Warning: unable to open an initial console.
Algorithmics/MIPS FPU Emulator v1.5
set_action 0
firmware version: 3.0.0.4.376_3861-g11c21b3
[1 init:init_nvram +4] init_nvram for 27
num_of_mssid_support(0x0092): [mssid] support [3] mssid
ctf: module license 'Proprietary' taints kernel.
et_module_init: passivemode set to 0x0
et_module_init: et_txq_thresh set to 0x400
bcm_robo_enable_switch: EEE is disabled
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.2002 (r3822 08)
hotplug net INTERFACE=eth0 ACTION=add
wl_module_init: passivemode set to 0x0
PCI: Enabling device 0000:01:01.0 (0000 -> 0002)
eth1: Broadcom BCM4331 802.11 Wireless Controller 6.30.163.2002 (r382208)
PCI: Enabling device 0000:02:01.0 (0000 -> 0002)
eth2: Broadcom BCM4331 802.11 Wireless Controller 6.30.163.2002 (r382208)
hotplug net INTERFACE=eth1 ACTION=add
hotplug net INTERFACE=eth2 ACTION=add
/ # check_action 0
start jffs2: 4, 1048576
Empty flash at 0x0006000c ends at 0x00060200
[1 init:init_main +7] main loop signal/state=17
start_logger:
start_usb
NTFS (with native replay) support included
optimized: speed
Build_for__asus_n66u_2011-10-27_U86_r187446_b122
_ifconfig: name=eth0 flags=1043 IFUP addr=(null) netmask=(null)
hotplug net INTERFACE=vlan1 ACTION=add
update_lan_state(lan_, 0, 0)
generate_wl_para(0x0e85): unit 0 subunit -1
num_of_mssid_support(0x0092): [mssid] support [3] mssid
generate_wl_para(0x1145): bw: 0
generate_wl_para(0x1147): chanspec: 0
generate_wl_para(0x1148): bw_cap: 3
generate_wl_para(0x114e): obss_coex: 1
wlconf_pre(0x0301): set vhtmode 1
hotplug net INTERFACE=vlan2 ACTION=add
generate_wl_para(0x0e85): unit 1 subunit -1
num_of_mssid_support(0x0092): [mssid] support [3] mssid
chanspec_fix(0x07d7): unit: 1, bw_cap: 3, chanspec: 0
generate_wl_para(0x1145): bw: 0
generate_wl_para(0x1147): chanspec: 0
generate_wl_para(0x1148): bw_cap: 3
generate_wl_para(0x114e): obss_coex: 1
wlconf_pre(0x0301): set vhtmode 1
set_wltxpower(0x0903): unit: 0, txpower: 100
set_wltxpower(0x0903): unit: 1, txpower: 100
start_lan: setting up the bridge br0
hotplug net INTERFACE=br0 ACTION=add
vlan1: cmd=14: Operation not supported
_ifconfig: name=vlan1 flags=1043 IFUP addr=(null) netmask=(null)
start_lan: setting MAC of br0 bridge to 10:C3:7B:xx:yy:zz
_ifconfig: name=eth1 flags=1043 IFUP addr=(null) netmask=(null)
generate_wl_para(0x0e85): unit 0 subunit -1
num_of_mssid_support(0x0092): [mssid] support [3] mssid
generate_wl_para(0x1145): bw: 0
generate_wl_para(0x1147): chanspec: 0
generate_wl_para(0x1148): bw_cap: 3
generate_wl_para(0x114e): obss_coex: 1
generate_wl_para(0x0e85): unit 0 subunit 1
generate_wl_para(0x0e85): unit 0 subunit 2
generate_wl_para(0x0e85): unit 0 subunit 3
_ifconfig: name=eth2 flags=1043 IFUP addr=(null) netmask=(null)
generate_wl_para(0x0e85): unit 1 subunit -1
num_of_mssid_support(0x0092): [mssid] support [3] mssid
chanspec_fix(0x07d7): unit: 1, bw_cap: 3, chanspec: 0
generate_wl_para(0x1145): bw: 0
generate_wl_para(0x1147): chanspec: 0
generate_wl_para(0x1148): bw_cap: 3
generate_wl_para(0x114e): obss_coex: 1
generate_wl_para(0x0e85): unit 1 subunit 1
generate_wl_para(0x0e85): unit 1 subunit 2
generate_wl_para(0x0e85): unit 1 subunit 3
_ifconfig: name=br0 flags=1043 IFUP addr=192.168.1.1 netmask=255.255.255.0
_ifconfig: name=lo flags=1043 IFUP addr=127.0.0.1 netmask=255.0.0.0
route_manip: cmd=ADD name=lo addr=127.0.0.0 netmask=255.0.0.0 gateway=0.0.0.0 metric=0
update_lan_state(lan_, 2, 0)
stop_nat_rules: apply the redirect_rules!
start_lan 1794
start_services 3284
# wanduck: Got LAN(-1) information:
# Enable direct rule
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
block hotplug INTERFACE=8/0/0 ACTION=add USBPORT=1-1.4 HOST=(null) DEVICE=sda
check_action 0
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: selected channel spec: 0x1904 (6u)
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: selected channel spec: 0xd99f (161u)
[1 init:start_dnsmasq +15] begin
[1 init:stop_dnsmasq +15] begin
[1 init:stop_dnsmasq +15] end
[1 init:start_dnsmasq +15] end
start_lan_port(0) 1
TZ watchdog
decomp: fname=/var/lib/misc/rstats-speed.gz
start_pptpd: getpid= 1
vlan1: cmd=14: Operation not supported
decomp: gzip -dc /var/lib/misc/rstats-speed.gz > /var/tmp/rstats-uncomp != 0
load: speed_count = 0
load: read source= save_path=
load_history: fname=/var/lib/misc/rstats-history.gz
decomp: fname=/var/lib/misc/rstats-history.gz
disk_monitor: starting...
disk_monitor: day=31, week=5, time=19:0.
disk_monitor: decide if scan the target...
disk_monitor: 0: wait_second=14400...
disk_monitor: 1: wait_second=14400...
disk_monitor: 2: wait_second=51771600...
disk_monitor: wait_second=14400...
disk_monitor: Pause...
decomp: gzip -dc /var/lib/misc/rstats-history.gz > /var/tmp/rstats-uncomp != 0
decomp: fname=/var/lib/misc/rstats-history.gz
decomp: gzip -dc /var/lib/misc/rstats-history.gz > /var/tmp/rstats-uncomp != 0
load_history: load failed
start_wan: start_wan_if(0)!
[1 init:start_wan_if +16] unit=0.
update_wan_state(wan0_, 0, 0)
convert_wan_nvram(wan0_)
_ifconfig: name=eth0 flags=0000 addr=(null) netmask=(null)
Attempt to kill tasklet from interrupt
** wan_ifname: eth0 is NOT UP
_ifconfig: name=eth0 flags=1043 IFUP addr=(null) netmask=(null)
update_wan_state(wan0_, 1, 0)
_ifconfig: name=eth0 flags=1043 IFUP addr=(null) netmask=(null)
start_auth:: done
start_wan_if(): End.
udhcpc_wan:: deconfig
_ifconfig: name=eth0 flags=1043 IFUP addr=0.0.0.0 netmask=(null)
wan_down(eth0)
wan_down(eth0): .
stop_auth:: done
route_manip: cmd=DEL name=eth0 addr=0.0.0.0 netmask=0.0.0.0 gateway=(null) metric=0
update_wan_state(wan0_, 3, 0)
update_wan_state(wan0_, 4, 3)
udhcpc:: deconfig done
[1 init:init_main +16] main loop signal/state=14
U2EC starting ...
NET CMD GETINFO
NET CMD GETINFO
NET CMD GETINFO(Last edited by davidjones102 on 18 Sep 2015, 01:35)
Hope you can find some time to give us a little help.