The TP-Link TL-WR800N is similar to the TL-WR700N but the WR800N has a MIMO radio.
It is AC powered and has only a single Ethernet port.
With 4MB Flash and 16MB of RAM it should be capable of running OpenWrt.
Factory Boot
Software Platform for MIPS
Creation date: Sep 2 2011, 11:40:56 (huangqingjia@tp-link.net)
Copyright(C) 2001-2012 by TP-LINK TECHNOLOGIES CO., LTD.
CPU: AR9341: AP123 Board
CPU freq: 535 MHZ
SDRAM size: 16 MB
ipaddr:192.168.1.1
serverip:192.168.1.100
file:vxWorks.img
Press Ctrl+C to stop auto-boot...
1
0
auto-booting...
Uncompressing...done
Starting at 0x80001000...
Attaching interface lo0... done
Rx clbufs 2048 each of size 1756
eth_rx_netpool_init: allocated, pDmaBuf=0x80b813e0, buffend = 80ef33e4
ATHRS27: resetting s27
ATHRS27: s27 reset done
eth_rx_netpool_init: done already!
Attached IPv4 interface to mirror unit 0
usrAppInitEx: 117: GPIO_OE = 71300
usrAppInitEx: 118: CP0 CONFIG = 80208483
usrAppInitEx: 119: CP0 CONFIG1 = bee3519e
-->starting wireless...
APCFG task id 809afc90
sysWlanInit ...
Create WLAN event task tWLANEventTask
Create mem partion 0x8098e460 for size 86016
AH_CAL_IN_FLASH_AHB
Boostrap clock 25MHz
ar9300RadioAttach: Need analog access recipe!!
Restoring Cal data from Flash
ath_get_caps[4716] rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps[4691] tx chainmask mismatch actual 3 sc_chainmak 0
Create OS_MESGQ Successfully at 0x8097ce70
osifp->queue_head = 0x8097d170
ag7240MemInit: allocated, dmabuf=0x80689450, buffend = 8094b654
Entering Task Loop
Entering WLAN event Task Loop
-->wps is shutdown!
ERROR:wireless OR ACL disable
sending message 80659820,24
sending message 80659820,24
TDDP: Now listening client request.
tddp is running.
httpInit: System File Registry successfully initialized.
httpInit: System File Manager successfully initialized.
httpInit: File System RPM successfully initialized.
httpInit: RPM dispatcher successfully initialized.
httpInit: MIME type guessing RPM successfully initialized.
httpInit: http Password Checking successfully initialized.
httpInit: http Access Control successfully initialized.
Software Platform for MIPS
Copyright(C) 2001-2010 by TP-LINK TECHNOLOGIES CO., LTD.
Creation date: Sep 22 2011, 11:26:20
# Starting WLAN !!!!
AP_STARTMODE=standard
AP_ENABLE=1
ATH_COUNTRYCODE=156
wlan_vap_create : enter. devhandle=0x80440e60, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x80440e60, opmode=IEEE80211_M_HOSTAP, flags=0x1.
osif_ioctl_create_vap: vap 0x80ffe970 vap->iv_unit 0
ieee80211_end_load: load done
ath0 end flag = 0x00028802
default
default
default
IEE80211-FREQ IOCTL vap 0x80ffe970 0,0,0
AP_CHMODE=11NGHT40PLUS
WLAN IOCTL AP_CHMODE=11NGHT40PLUS=11NGHT20=11NGHT40PLUS=1003
IEE80211-MODE IOCTL 1,11NGHT40PLUS,13
set mode 11,-2130709132,6
set mode retv 0
WLAN IOCTL AP_PRIMARY_CH=auto=6=auto=1002
IEE80211-FREQ IOCTL vap 0x80ffe970 0,0,11
WLAN IOCTL PUREG=0=0=0=1004
IEEE80211-SETPURGE IOCTL 0
WLAN IOCTL AP_HIDE_SSID=0=0=0=1005
IEEE80211-SETHIDESSIDIOCTL 0
WLAN IOCTL AP_ISOLATION=0=0=0=1034
IEE80211-setparam-nobridge 0
WLAN IOCTL AP_TX11NRATE==0x0=0x0=1041
set auto rate
WLAN IOCTL AP_11G_PROTECTION==0=0=1042
WLAN IOCTL AP_BEACON_INTERVAL=100=100=100=1043
WLAN IOCTL AP_FRAGMENT_THRESHOLD=2346=2346=2346=1044
WLAN IOCTL AP_RTS_THRESHOLD=2346=2347=2346=1046
WLAN IOCTL AP_DTIM_PERIOD=1=1=1=1045
WLAN IOCTL AP_WMM_ENABLE=1=1=1=1051
WLAN IOCTL AP_WMM_NOACK==0=0=1052
IOCTL set wmm noack 0
WLAN IOCTL AP_CYPHER_2==CCMP=CCMP=1000
Get EIOCGADDR
WLAN IOCTL AP_NO_EDGE_CH==0=0=1056
WLAN IOCTL AP_MCASTRATE==0=0=1018
WLAN IOCTL AP_MACFILTER_MODE==0=0=1038
WLAN IOCTL AP_MACFILTER_LIST====1000
Get EIOCGADDR
WLAN IOCTL AP_SHORT_GI=1=1=1=1055
WLAN IOCTL AP_DISABLECOEXT=1=0=1=1075
WLAN IOCTL AP_SSID=TP-LINK_PocketAP_839F2E=Ath_AP123ng=TP-LINK_PocketAP_839F2E=1001
IEE80211-ESSID IOCTL 1,TP-LINK_PocketAP_839F2E,24
AP_CHMODE=11NGHT40PLUS
AP_CWMMODE=1
IEE80211-CWMMODE IOCTL 1
AP_AMPDU=0
AP_PURE_N=0
AP_TX_CHAINMASK=3
AP_RX_CHAINMASK=3
AP_SECMODE=None
WPS_ENABLE=0
Security Mode: None
IEE80211-setparam-authmode 1
AP_MACFILTER_MODE=0
ieee80211_open
WLAN IOCTL AP_BASICRATES====1039
WLAN IOCTL AP_DEBUG=0==0=1062
WLAN IOCTL AP_TX_POWER====1073
Starting Hostapd
AP_SSID=TP-LINK_PocketAP_839F2E
AP_HOSTAPD_DEBUG=
AP_IPADDR=192.168.1.2
AP_SECMODE=None
WPS BSS init
WPS_ENABLE=0
AP_SECMODE=None
WPS OPEN BSS init
Adding ath0 in bridge ...
default
Set EIOCGMIB2
default
# ?
command description
-------------------------------
help print all commands
arpShow arp show
bridgeShow bridge info show
call call a function by the function pointer
netPoolShow netPoolShow [data][sys][eth][wlan]
endPacket endPacket debug
ifShow interface show
iosFdShow display a list of file descriptor names in the system
task print task information
logo print Logo
memShow mem show
mem print mem information, limited 16KB
inetStatShow Active Internet connections show
natShow nat show
routeShow route show
reboot Reboot the systerm
netPoolShow netPoolShow [data][sys][eth][wlan]
stack print task stack
ethreg -r reg(0x) value(0x)
-p phyUnit(0x) reg(0x) value(0x)
-o regAddr(0x) value(0x)
ping ping a host
arpAdd add an ARP
arpDelete del an ARP
ifconfig config interface
routec route cmd
memset memory set
memtest memory test
s26_wanstatus show wan link status
s26_portstatus show s26's port status
ag7240DbgLevel set ag7240 debug level
ethrxring dump rx rings' info on eth
buttontest test QSS/restoredefault button
wlaninit apcfg_autostart
wlanup apcfg_wlanstart
wlandown apcfg_wlanstop
wlanup_hostapd start wlan with hostapd
wlanup_supplicant start wlan with with supplicant
to turn on/off debug statement in wlan driver