OpenWrt Forum Archive

Topic: Realtek SoC support in OpenWrt

The content of this topic has been archived between 22 Sep 2016 and 30 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

Hellp,

Opened up my DIR-822A1 H/W ver:C1 P/N CIR822LCA....C1 Hope someone is working on supporting this one..

ChipSet

RTL8197DL
RTL8192ER    802.11bgn PCIe Network Interface Controller
RTL8812AR    802.11ac/abgn PCIe WLAN Network Controller
ESMT M14D5121632A    8M x 16 Bit x 4 Banks DDR II SDRAM
MX25L6406E    64M-BIT [x 1 / x 2] CMOS SERIAL FLASH
20PT1024RX
12PS6121A

WRG-AC43 on top of board
KA2IR822A1 FCC ID

Serial bootup at 38400,8N1

Serial Port pin

1 TX
2 Gnd
3 3.3v

4 RX
Pictures and boot log  at following link https://www.dropbox.com/sh/9gg3jr8ptwex … IdTda?dl=0


is anyone working on Openwrt for this router I would love to flash it with CC

Update:

just found the following not sure it would work on my router https://wiki.openwrt.org/toh/alfa.network/ac1200r

(Last edited by pusky on 10 May 2017, 03:30)

Is the 8197 still a Lexra core or a true MIPS?

Still Lexra core RLX5281 CPU..

Have not been able to find the difference between RTL8197DL and RTL8197D.

hi all/ Roman,

I recently came across this specific post in regard on rtl8196c device, there are many routers/repeaters running on this chip in the market but not enough firmware support on many infamous branded devices. I searched around on the web for weeks and could not find any firmware for it(factory does not offer any updates).

I have an anker 300M WIFI repeater/router, the device works quiet stable but I found the firmware in it is kinda old and the setting is very limited. Im wonder if anyone has similar firmware devices which I can try? Im somewhat novices on Linux and android but do not mind to try and share experiences. Below are the details on my Anker repeater. Thanks in advance for anyone can share some info.

Anker 66ANWNWR-WA 300M repeater/rounter
CPU RTL-8196C
RAM EM639105TS-6G(16MB)
ROM MX25L3206E(4MB)
WIFI RTL-8192CE

It has reset button,wps button, ap/repeater/clint switch.

Hello, guys!

I opened up a Multilaser RE073. Probably Totolink N150RH ou Zioncom IP04159E re-branded. The external resemblance for the Totolink is unquestionable.

It was night and I could not do a better visual inspection. I'll open it again and take better pictures.

Info

Ethernet: It is covered by a heat sink
Wifi: RTL8188RE
Filter: H7201DG
Flash: ?
RAM: Winbond W9812G6JH-6 (16 MB)
Power supply: 12 V 1000 mA
Serial: I need help to determine it
Bootloader: I need help to determine it

nmap -P0 -O

OS details: Linux 2.4.9 - 2.4.18 (likely embedded)

klogd

BusyBox v1.1.3 (2012.06.25)
RTL8192C/RTL8188C driver version 1.4 (2010-08-11)

Note: "RTL8188C" is not the RTL8188RE which is soldered!

Questions

1) Is there some relation with the RTL8196C port?

2) Could someone here share photos of some of these routers?

(Last edited by alexandre-mbm on 22 May 2017, 21:24)

Greeting.
Can you get openwrt firmware in jnr3000?

Hi guys. I have developed a firmware for router RE300R4-2T2R-V8. Compilling seems ok but, doesn't work. Do not flash!! This router have 4MB of Flash and 16 of RAM.
Here some more information:
RLX Linux version 2.0

# cat /proc/version
Linux version 3.10.90 (root@localhost.localdomain) (gcc version 4.6.4 (Realtek R
SDK-4.6.4 Build 2080) ) #10 Fri May 5 10:31:09 CST 2017
# cat /proc/cpuinfo
system type             : RTL8196E
machine                 : Unknown
processor               : 0
cpu model               : 52481
BogoMIPS                : 398.13
tlb_entries             : 32
mips16 implemented      : yes
# cat /proc/meminfo
MemTotal:          24724 kB
MemFree:           12852 kB
Buffers:            1136 kB
Cached:             3168 kB
SwapCached:            0 kB
Active:             3328 kB
Inactive:           2512 kB
Active(anon):       1536 kB
Inactive(anon):        0 kB
Active(file):       1792 kB
Inactive(file):     2512 kB
Unevictable:           0 kB
Mlocked:               0 kB
SwapTotal:             0 kB
SwapFree:              0 kB
Dirty:                 0 kB
Writeback:             0 kB
AnonPages:          1548 kB
Mapped:              976 kB
Shmem:                 0 kB
Slab:               4148 kB
SReclaimable:        424 kB
SUnreclaim:         3724 kB
KernelStack:         296 kB
PageTables:          280 kB
NFS_Unstable:          0 kB
Bounce:                0 kB
WritebackTmp:          0 kB
CommitLimit:       12360 kB
Committed_AS:       4980 kB
VmallocTotal:    1048372 kB
VmallocUsed:         132 kB
VmallocChunk:    1048232 kB
# cat /proc/interrupts
           CPU0
  8:          0  RLX LOPI  cascade
  9:        184  RLX LOPI  serial
11:      20514  RLX LOPI  EXT
12:        893  RLX LOPI  eth0
14:       7997  RLX LOPI  wlan0
ERR:          0
# cat /proc/partitions
major minor  #blocks  name
  31        0       2048 mtdblock0
  31        1       2048 mtdblock1
# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00200000 00001000 "boot+cfg+linux"
mtd1: 00200000 00001000 "rootfs"


# cat /var/log/messages.0
May  5 10:31:13 rlx-linux syslog.info syslogd started: BusyBox v1.13.4
May  5 10:31:13 rlx-linux kern.notice kernel: klogd started: BusyBox v1.13.4 (20
17-05-05 10:26:10 CST)
May  5 10:31:13 rlx-linux kern.warn kernel: Realtek GPIO Driver for Flash Reload
Default
May  5 10:31:13 rlx-linux kern.warn kernel: SPI INIT
May  5 10:31:13 rlx-linux kern.warn kernel:  ------------------------- Force int
o Single IO Mode ------------------------
May  5 10:31:13 rlx-linux kern.warn kernel: |No chipID  Sft chipSize blkSize sec
Size pageSize sdCk opCk      chipName    |
May  5 10:31:13 rlx-linux kern.warn kernel: | 0 c84016h  0h  400000h  10000h   1
000h     100h   80    0           GD25Q32|
May  5 10:31:13 rlx-linux kern.warn kernel:  -----------------------------------
-----------------------------------------
May  5 10:31:13 rlx-linux kern.info kernel: SPI flash(GD25Q32) was found at CS0,
size 0x400000
May  5 10:31:13 rlx-linux kern.notice kernel: 2 rtkxxpart partitions found on MT
D device flash_bank_1
May  5 10:31:13 rlx-linux kern.notice kernel: Creating 2 MTD partitions on "flas
h_bank_1":
May  5 10:31:13 rlx-linux kern.notice kernel: 0x000000000000-0x000000200000 : "b
oot+cfg+linux"
May  5 10:31:13 rlx-linux kern.notice kernel: 0x000000200000-0x000000400000 : "r
ootfs"
May  5 10:31:13 rlx-linux kern.warn kernel: Find Port=0 Device:Vender ID=818b10e
c
May  5 10:31:13 rlx-linux kern.warn kernel: MACHAL_version_init
May  5 10:31:13 rlx-linux kern.warn kernel: ####################################
###################
May  5 10:31:13 rlx-linux kern.warn kernel: SKB_BUF_SIZE=2408 MAX_SKB_NUM=400
May  5 10:31:13 rlx-linux kern.warn kernel: ####################################
###################
May  5 10:31:13 rlx-linux kern.info kernel: nf_conntrack version 0.5.0 (384 buck
ets, 1536 max)
May  5 10:31:13 rlx-linux kern.info kernel: ip_tables: (C) 2000-2006 Netfilter C
ore Team
May  5 10:31:13 rlx-linux kern.info kernel: TCP: cubic registered
May  5 10:31:13 rlx-linux kern.info kernel: NET: Registered protocol family 10
May  5 10:31:13 rlx-linux kern.info kernel: ip6_tables: (C) 2000-2006 Netfilter
Core Team
May  5 10:31:13 rlx-linux kern.info kernel: sit: IPv6 over IPv4 tunneling driver
May  5 10:31:13 rlx-linux kern.info kernel: ip6_gre: GRE over IPv6 tunneling dri
ver
May  5 10:31:13 rlx-linux kern.info kernel: NET: Registered protocol family 17
May  5 10:31:13 rlx-linux kern.info kernel: l2tp_core: L2TP core driver, V2.0
May  5 10:31:13 rlx-linux kern.info kernel: 8021q: 802.1Q VLAN Support v1.8
May  5 10:31:13 rlx-linux kern.warn kernel: Realtek FastPath:v1.03
May  5 10:31:13 rlx-linux kern.warn kernel: Probing RTL819X NIC-kenel stack size
order[1]...
May  5 10:31:13 rlx-linux kern.warn kernel: eth0 added. vid=9 Member port 0x10f.
..
May  5 10:31:13 rlx-linux kern.warn kernel: eth1 added. vid=8 Member port 0x10..
.
May  5 10:31:13 rlx-linux kern.warn kernel: [peth0] added, mapping to [eth1]...
May  5 10:31:13 rlx-linux kern.err kernel: SQUASHFS error: Xattrs in filesystem,
these will be ignored
May  5 10:31:13 rlx-linux kern.err kernel: SQUASHFS error: unable to read xattr
id index table
May  5 10:31:13 rlx-linux kern.info kernel: VFS: Mounted root (squashfs filesyst
em) readonly on device 31:1.
May  5 10:31:13 rlx-linux kern.info kernel: Freeing unused kernel memory: 148K (
8041b000 - 80440000)
May  5 10:31:13 rlx-linux kern.info kernel: device eth0 entered promiscuous mode
May  5 10:31:13 rlx-linux kern.info kernel: device wlan0 entered promiscuous mod
e
May  5 10:31:13 rlx-linux kern.warn kernel: WlanSupportAbility = 0x3
May  5 10:31:13 rlx-linux kern.warn kernel: eric-8822 [ODM_software_init][12656]
May  5 10:31:22 rlx-linux daemon.info pppd[256]: RP-PPPoE plugin version 3.3 com
piled against pppd 2.4.4
May  5 10:31:22 rlx-linux daemon.notice pppd[256]: pppd 2.4.4 started by root, u
id 0
May  5 10:31:22 rlx-linux daemon.info init: starting pid 259, tty '': '-/bin/sh'
May  5 10:31:57 rlx-linux user.notice pppoe:
May  5 10:31:57 rlx-linux user.notice Timeout waiting for PADO packets
May  5 10:31:57 rlx-linux daemon.err pppd[256]: Timeout waiting for PADO packets
May  5 10:31:58 rlx-linux daemon.notice pppd[256]: Connection terminated.
May  5 10:31:58 rlx-linux daemon.err pppd[256]: Unable to complete PPPoE Discove

Hi guys. I have developed a firmware for router RE300R4-2T2R-V8. Compilling seems ok but, doesn't work. Do not flash!! This router have 4MB of Flash and 16 of RAM.

Is there any chances to look at your sources?
I have some success on building rlx4181 toolchain based on 4.8.1 gcc and 2.23.1 binutils. Tested on rtl8196c.
Can test your build on it 4/32M

Hello, friends, i have netis wf-2419e router, CPU is RTL8196e, I need to make it work with OpenWRT. I have already build firmware with realtek sdk, but how I can flash it? I have 4Mb flash and 16Mb ram.

maestrodan wrote:

Hello, friends, i have netis wf-2419e router, CPU is RTL8196e, I need to make it work with OpenWRT. I have already build firmware with realtek sdk, but how I can flash it? I have 4Mb flash and 16Mb ram.

Any progress maestrodan?

I have buyed a router+repeater AC750W or UNT-750 on Amazon.

Chip: RTL8881AN+8192ER
Flash: 4MB
SDRAM: DDR2 32MB

amazon.it/gp/product/B073JHDKCM/

Where i can fund a rom for RTL8881AN+8192ER of less of 4MB? i found a only link for a 4.4MB build for that chip that i cant obviusely use in 4MB flash.

Hello,

I have a Trendnet TEW-731br v3, i'm trying to replace the stock firmware with something else that could allow me to pass an option to the dhcp client (vendor_class_id).
I have successfully build openwrt for realtek 8196e + 8192er (sourceforge.net/projects/rtl819x/).
but i can't get openwrt to be flashed with tftp method, there is a tftp server on 192.168.1.6 that listen when the router start, sending the file with curl -T works but when the router reboot this is still with the stock firmware.

I have started to take a look at the serial connection, the following is the boot log with the stock firmware. For now that's all that I have.

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2017.12.10 09:51:16 =~=~=~=~=~=~=~=~=~=~=~=
 
Booting...
 

@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

@

@ chip__no chip__id mfr___id dev___id cap___id size_sft dev_size chipSize

@ 0000000h 0c22015h 00000c2h 0000020h 0000015h 0000000h 0000015h 0200000h

@ blk_size blk__cnt sec_size sec__cnt pageSize page_cnt chip_clk chipName

@ 0010000h 0000020h 0001000h 0000200h 0000100h 0000010h 000004eh MX25L1605D

@ 

@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

 

---RealTek(RTL8196E)at 2013.03.21-09:42+0800 v0.3 [16bit](400MHz)

P0phymode=01, embedded phy


---Ethernet init Okay!

support multicast tool


time out ......


OSK image found src=0xbd041834 

mapping IMEM/DMEM out of memory(upper 128MB space) 

decompress

startBuf=0xbd041841, compressedSize=1036907, outBuf=0x80000000, outSizeFull=3177492

  ok!

 create memory pool: start at 0x80307c18, size 5211112
spi_init(1270) c2/20
SPI flash found: id c2/20
sector_size:0x1000 num_of_sector:512
4 wired tlb entry, 1 pages for pgt
 mib chain:WLAN_MBSSID descpritor's size don't match its recordSize, please check it! 
 mib chain:WLAN_VXD descpritor's size don't match its recordSize, please check it! 
 mib chain:DHCP_SERVING_POOL descpritor's size don't match its recordSize, please check it! 
 mib chain:URL_STR descpritor's size don't match its recordSize, please check it! 
 mib chain:KEYWORD_STR descpritor's size don't match its recordSize, please check it! 
 mib chain:DOMAIN_STR descpritor's size don't match its recordSize, please check it! 
 mib chain:NATRULE_INSRC descpritor's size don't match its recordSize, please check it! 
 mib chain:NATRULE_INSRC_STATIC descpritor's size don't match its recordSize, please check it! 
 mib chain:NATRULE_INSRC_FROM descpritor's size don't match its recordSize, please check it! 
 mib chain:IP_MARK descpritor's size don't match its recordSize, please check it! 
 mib chain:IP_ACL_STD_ENTRY descpritor's size don't match its recordSize, please check it! 
 mib chain:IP_ACL_EXT_ENTRY descpritor's size don't match its recordSize, please check it! 
 mib chain:QOS_RULE descpritor's size don't match its recordSize, please check it! 
 mib chain:DYNAMIC_DNS descpritor's size don't match its recordSize, please check it! 
 mib chain:NAT_PORTRIGGER_RULES descpritor's size don't match its recordSize, please check it! 
 mib chain:NAT_PRIORITY_RULES descpritor's size don't match its recordSize, please check it! 
 mib chain:RA_ENTRY descpritor's size don't match its recordSize, please check it! 
 mib chain:DHCPV6_UUID descpritor's size don't match its recordSize, please check it! 
flash hw  config addr:0xbfc0a000 size:8192
uncompress: preLen:329, unPreLen:778
flash sw default config addr:0xbfc0c000 size:8192
uncompress: preLen:167, unPreLen:245
set WLAN_REG_DOMAIN default value:0x3
set WLAN_COUNTRY_AREA default value:0x12
set WLAN_ROOT_SSID default value:TRENDnet731_VK7P
set WLAN_ENCRYPT default value:0x6
set WLAN_WPA_PSK default value:xxxxxxxx
flash sw  config addr:0xbfdf8000 size:32768
uncompress: preLen:6763, unPreLen:28331
system config initial finsihed.
registerTask stackp=0x50001000, size 12288, name=CFGTASK
registerTask stackp=0x50004000, size 12288, name=STPMAIN
registerTask stackp=0x50007000, size 16384, name=CLITASK
registerTask stackp=0x5000b000, size 12288, name=GENTSK
registerTask stackp=0x5000e000, size 12288, name=XTCPIP
registerTask stackp=0x50011000, size 16384, name=EWSTSK
registerTask stackp=0x50015000, size 4096, name=FEATTASK
registerTask stackp=0x50016000, size 12288, name=PPPoE
registerTask stackp=0x50019000, size 12288, name=ppp
registerTask stackp=0x5001c000, size 12288, name=TFTPD
registerTask stackp=0x5001f000, size 12288, name=TFTP
registerTask stackp=0x50022000, size 12288, name=DNS
registerTask stackp=0x50025000, size 12288, name=DDNS
registerTask stackp=0x50028000, size 16384, name=Telnet
registerTask stackp=0x5002c000, size 12288, name=DHCP
registerTask stackp=0x5002f000, size 12288, name=NTP
registerTask stackp=0x50032000, size 12288, name=UPNP
registerTask stackp=0x50035000, size 12288, name=rtl8670
registerTask stackp=0x50038000, size 32768, name=auth_wlan
registerTask stackp=0x50040000, size 12288, name=WSC
registerTask stackp=0x50043000, size 12288, name=dhcpv6d
registerTask stackp=0x50046000, size 12288, name=dhcpv6c
registerTask stackp=0x50049000, size 4096, name=IDLETSK
eraseUnusedFlash fromSector=0xbfd40000 
~~~~bufsize = 2164,datapool->start = 0x803bc93c,datapool->end = 0x80465a3c~~~~
Calibrating delay loop... 398.95 BogoMIPS



Probing RTL8186 10/100 NIC...
chip name: RTL8196C, chip revid: 0
Set threshould idx 1
_rtl865x_addVlan add vlan 9
_rtl865x_addVlan add vlan 8
===_rtl865x_attachMasterNetif(1129),slave(ppp0),master(eth1),slave_netif->master(0x0)
rtl865x_set_hwaddr 2204 dev->name 
eth1 set netif mac to: 3c:8c:f8:80:84:c3

net wan Init
wlan0Init: idx=0, mac=3c8cf88084c2
rtk_wlan_init:212
RTL8192C-RTL8188C driver version 1.5 (92ER-2013-06-20-r3064(*))
 wlan_index:0  0, 6,0xb9000000,0xb8b10000,21
=====>>INSIDE rtl8192cd_init_one <<=====
PCIE reset (0) 
Do MDIO_RESET
98 - 25MHz Clock Source
Find Port=0 Device:Vender ID=818b10ec
vendor_deivce_id=818b10ec

 found 8192E !!! 
HalAssociateNic OK 
StopHW Succeed
osk_register_netdev:wlan0, dev=0x80383730
=====>>EXIT rtl8192cd_init_one <<=====
<rtl8192cd_init_one>LZQ: GPIO_PIN_CTRL[0x44] 
<rtl8192cd_init_one>LZQ: before read tmpReg[0x2e] 
<rtl8192cd_init_one>LZQ: after read tmpReg[0x2e] 
=====>>INSIDE rtl8192cd_init_one <<=====
osk_register_netdev:wlan0-vxd, dev=0x8047611c
=====>>EXIT rtl8192cd_init_one <<=====
<rtl8192cd_init_one>LZQ: GPIO_PIN_CTRL[0x44] 
<rtl8192cd_init_one>LZQ: before read tmpReg[0x2e] 
<rtl8192cd_init_one>LZQ: after read tmpReg[0x2e] 
=====>>INSIDE rtl8192cd_init_one <<=====
osk_register_netdev:wlan0-vap0, dev=0x80491dfc
=====>>EXIT rtl8192cd_init_one <<=====
<rtl8192cd_init_one>LZQ: GPIO_PIN_CTRL[0x44] 
<rtl8192cd_init_one>LZQ: before read tmpReg[0x2e] 
<rtl8192cd_init_one>LZQ: after read tmpReg[0x2e] 
=====>>INSIDE rtl8192cd_init_one <<=====
osk_register_netdev:wlan0-vap1, dev=0x804adadc
=====>>EXIT rtl8192cd_init_one <<=====
<rtl8192cd_init_one>LZQ: GPIO_PIN_CTRL[0x44] 
<rtl8192cd_init_one>LZQ: before read tmpReg[0x2e] 
<rtl8192cd_init_one>LZQ: after read tmpReg[0x2e] 
=====>>INSIDE rtl8192cd_init_one <<=====
osk_register_netdev:wlan0-vap2, dev=0x804c97bc
=====>>EXIT rtl8192cd_init_one <<=====
<rtl8192cd_init_one>LZQ: GPIO_PIN_CTRL[0x44] 
<rtl8192cd_init_one>LZQ: before read tmpReg[0x2e] 
<rtl8192cd_init_one>LZQ: after read tmpReg[0x2e] 
=====>>INSIDE rtl8192cd_init_one <<=====
osk_register_netdev:wlan0-vap3, dev=0x804e549c
=====>>EXIT rtl8192cd_init_one <<=====
<rtl8192cd_init_one>LZQ: GPIO_PIN_CTRL[0x44] 
<rtl8192cd_init_one>LZQ: before read tmpReg[0x2e] 
<rtl8192cd_init_one>LZQ: after read tmpReg[0x2e] 
init ok!!!wlan_index:1
enter rtk_wlan_config_root
wlan0 set_mib ACS_forMa=0
wlan0 set_mib use40M=0
wlan0 set_mib coexist=0
wlan0 set_mib ampdu=1
wlan0 set_mib shortGI20M=1
wlan0 set_mib shortGI40M=1
wlan0 set_mib regdomain=3
wlan0 set_mib led_type=7
wlan0 set_mib ssid=TRENDnet731_VK7P
wlan0 set_mib vap_enable=0
wlan0 set_mib opmode=16
wlan0 set_mib shortretry=0
wlan0 set_mib longretry=0
wlan0 set_mib pwrlevelCCK_A=3030302e2e2e2e31313131313131
wlan0 set_mib pwrlevelCCK_B=3030302d2d2d2d2f2f2f2f2f2f2f
wlan0 set_mib pwrlevelHT40_1S_A=2b2b2b292929292b2b2b2b2b2b2b
wlan0 set_mib pwrlevelHT40_1S_B=2828282626262627272727272727
wlan0 set_mib pwrdiffHT40_2S=0000000000000000000000000000
wlan0 set_mib pwrdiffHT20=0000000000000000000000000000
wlan0 set_mib pwrdiffOFDM=3232322121212132323232323232
wlan0 set_mib xcap=42
wlan0 set_mib ther=33
wlan0 set_mib bcnint=100
wlan0 set_mib channel=0
wlan0 set_mib basicrates=15
wlan0 set_mib oprates=4095
wlan0 set_mib autorate=1
wlan0 set_mib rtsthres=2347
wlan0 set_mib fragthres=2346
wlan0 set_mib expired_time=30000
wlan0 set_mib preamble=0
wlan0 set_mib hiddenAP=0
wlan0-vap0 set_mib hiddenAP=0
wlan0-vap1 set_mib hiddenAP=0
wlan0-vap2 set_mib hiddenAP=0
wlan0-vap3 set_mib hiddenAP=0
wlan0 set_mib dtimperiod=1
wlan0 set_mib aclnum=0
wlan0 set_mib aclmode=0
wlan0 set_mib authtype=2
wlan0-vap0 set_mib authtype=2
wlan0-vap1 set_mib authtype=2
wlan0-vap2 set_mib authtype=2
wlan0-vap3 set_mib authtype=2
wlan0 set_mib encmode=6
wlan0-vap0 set_mib encmode=0
wlan0-vap1 set_mib encmode=0
wlan0-vap2 set_mib encmode=0
wlan0-vap3 set_mib encmode=0
wlan0 set_mib psk_enable=0
wlan0 set_mib wpa_cipher=0
wlan0 set_mib wpa2_cipher=0
wlan0 set_mib lgyEncRstrct=15
wlan0-vap0 set_mib psk_enable=0
wlan0-vap0 set_mib wpa_cipher=0
wlan0-vap0 set_mib wpa2_cipher=0
wlan0-vap0 set_mib lgyEncRstrct=15
wlan0-vap1 set_mib psk_enable=0
wlan0-vap1 set_mib wpa_cipher=0
wlan0-vap1 set_mib wpa2_cipher=0
wlan0-vap1 set_mib lgyEncRstrct=15
wlan0-vap2 set_mib psk_enable=0
wlan0-vap2 set_mib wpa_cipher=0
wlan0-vap2 set_mib wpa2_cipher=0
wlan0-vap2 set_mib lgyEncRstrct=15
wlan0-vap3 set_mib psk_enable=0
wlan0-vap3 set_mib wpa_cipher=0
wlan0-vap3 set_mib wpa2_cipher=0
wlan0-vap3 set_mib lgyEncRstrct=15
wlan0-vxd set_mib psk_enable=0
wlan0-vxd set_mib wpa_cipher=0
wlan0-vxd set_mib wpa2_cipher=0
wlan0-vxd set_mib lgyEncRstrct=15
wlan0 set_mib psk_enable=1
wlan0 set_mib encmode=4
wlan0 set_mib wpa_cipher=8
wlan0 set_mib psk_enable=2
wlan0 set_mib encmode=4
wlan0 set_mib wpa2_cipher=8
wlan0 set_mib passphrase=73131R59709
wlan0 set_mib 802_1x=1
wlan0-vap0 set_mib 802_1x=0
wlan0-vap1 set_mib 802_1x=0
wlan0-vap2 set_mib 802_1x=0
wlan0-vap3 set_mib 802_1x=0
wlan0 set_mib band=11
wlan0 set_mib deny_legacy=0
wlan0-vap0 set_mib band=11
wlan0-vap0 set_mib deny_legacy=0
wlan0-vap1 set_mib band=11
wlan0-vap1 set_mib deny_legacy=0
wlan0-vap2 set_mib band=11
wlan0-vap2 set_mib deny_legacy=0
wlan0-vap3 set_mib band=11
wlan0-vap3 set_mib deny_legacy=0
wlan0 set_mib lowestMlcstRate=0
wlan0 set_mib cts2self=1
wlan0 set_mib disable_protection=0
wlan0 set_mib block_relay=0
wlan0-vap0 set_mib block_relay=0
wlan0-vap1 set_mib block_relay=0
wlan0-vap2 set_mib block_relay=0
wlan0-vap3 set_mib block_relay=0
wlan0-vxd set_mib block_relay=0
wlan0 set_mib qos_enable=1
wlan0 set_mib mc2u_disable=0
exit rtk_wlan_config_root
rtk_wlan_set_mac_addr: 802fd7c0,80383730
wlan0Init: idx=1, mac=3c8cf88084c3
rtk_wlan_set_mac_addr: 802fd7d0,80491dfc
wlan0Init: idx=2, mac=3c8cf88084c4
rtk_wlan_set_mac_addr: 802fd7e0,804adadc
wlan0Init: idx=3, mac=3c8cf88084c5
rtk_wlan_set_mac_addr: 802fd7f0,804c97bc
wlan0Init: idx=4, mac=3c8cf88084c6
rtk_wlan_set_mac_addr: 802fd800,804e549c
wlan0Init: idx=5, mac=3c8cf88084c2
rtk_wlan_set_mac_addr: 802fd810,8047611c

Port        ifindex range
Br        1
Wan        2-9
Wlan root        10
Wlan vap        11-14
Wlan vxd        15
PPP        16-23
Switch        24-27
####initial default route table!
####initial local route table!
####inital 4 port mapping route tables!
####inital 5 port mapping tables!
alloc 9k bytes for route table
dns wait time is 2 secs
dhcpv6dmain start..............................
#######ipCircCreate type=1 if_id=1 rcid=0
ipCircSetIPA id_pyhport=1 c->rc_id=1 phyport=1
xipCreateVif...................
ipCircEnable  1167...............
####add 0xc0a80a01/0xffffffff in route table 0x805b2c10! cid=1 src=0xc0a80a01
####add 0xc0a80a00/0xffffff00 in route table 0x805b2c10! cid=1 src=0xc0a80a01
ipCircEnable  1167...............
miiar_write phy 3, reg 0, val 0x8000

miiar_write phy 3, reg 4, val 0xde1

miiar_write phy 3, reg 0, val 0x1200

miiar_write phy 2, reg 0, val 0x8000

miiar_write phy 2, reg 4, val 0xde1

miiar_write phy 2, reg 0, val 0x1200

miiar_write phy 1, reg 0, val 0x8000

miiar_write phy 1, reg 4, val 0xde1

miiar_write phy 1, reg 0, val 0x1200

miiar_write phy 0, reg 0, val 0x8000

miiar_write phy 0, reg 4, val 0xde1

miiar_write phy 0, reg 0, val 0x1200

init_rtsp_ssrc 39
nat entry's size is 176 bytes
Nat Entry Maxinum:    2048    
gNatCachePoolp=0x802f1408 gNatCachePoolp->qcnt=2048 sizeof(Nat_T)=176 
natRuleAdd 2412 flags=0x00000009 sip=0.0.0.0 eip=0.0.0.0
enqueue item to queue!
portrigger rule total 0 !
enable priority feature##########################
priority rule total 0 !
enable priority feature##########################
priority rule total 0 !
cfgSetIgmpProxyAnyItf  isDisable=1
*******ipv6Init() Start*******
ipfw2 (+ipv6) initialized, divert loadable, nat loadable, rule-based forwarding disabled, default to accept, logging disabled
Enter SetupFWRule!
do_firewall_cmd:command=flush 
Flushed all rules.
do_firewall_cmd() execute successfully!
do_firewall_cmd:command=add check-state  
do_firewall_cmd() execute successfully!
do_firewall_cmd:command=add skipto 1000 icmp6 from any to any icmp6types 128,129 
do_firewall_cmd() execute successfully!
do_firewall_cmd:command=add allow icmp6 from any to any 
do_firewall_cmd() execute successfully!
do_firewall_cmd:command=add 1000 skipto 5000 ip6 from any to me6 in via e1 
do_firewall_cmd() execute successfully!
do_firewall_cmd:command=add skipto 5000 ip6 from me6 to any out via e1 
do_firewall_cmd() execute successfully!
do_firewall_cmd:command=add skipto 10000 ip6 from any to me6 in via wan 
do_firewall_cmd() execute successfully!
do_firewall_cmd:command=add skipto 10000 ip6 from me6 to any out via wan 
do_firewall_cmd() execute successfully!
do_firewall_cmd:command=add skipto 15000 ip6 from any to any 
do_firewall_cmd() execute successfully!
Enter SetupLanAclRule!
do_firewall_cmd:command=set 1 flush  
Flushed all rules.
do_firewall_cmd() execute successfully!
do_firewall_cmd:command=add 9980 set 1 allow ip6 from any to any out keep-state 
do_firewall_cmd() execute successfully!
do_firewall_cmd:command=add 9990 set 1 allow ip6 from any to any in keep-state 
do_firewall_cmd() execute successfully!
Enter SetupWanAclRule!
do_firewall_cmd:command=set 2 flush  
Flushed all rules.
do_firewall_cmd() execute successfully!
do_firewall_cmd:command=add 10010 set 2 allow icmp6 from any to any in keep-state icmp6types 128,129
do_firewall_cmd:command=add 14980 set 2 allow ip6 from any to any out keep-state 
do_firewall_cmd() execute successfully!
do_firewall_cmd:command=add 14990 set 2 deny ip6 from any to any in 
do_firewall_cmd() execute successfully!
Enter SetupWanAclRule!
do_firewall_cmd:command=set 3 flush  
Flushed all rules.
do_firewall_cmd() execute successfully!
do_firewall_cmd:command=add 19980 set 3 allow ip6 from any to any out recv e1 xmit wan keep-state 
do_firewall_cmd() execute successfully!
do_firewall_cmd:command=add 19990 set 3 allow ip6 from any to any out recv wan xmit e1 keep-state 
do_firewall_cmd() execute successfully!
*******ipv6Init() End*******
getCommonDivisorfromArray 940 len=4 (40 30 20 10)
getCommonDivisorfromArray 951 g=10
wfqScale[0]=4
wfqScale[1]=3
wfqScale[2]=2
wfqScale[3]=1
wlan_itf_start>Wlan is going up..........[6]
enable idx=0
rtk_wlan_open:241>wlan0
PrepareRXBD88XX(221): pdesc_dma_buf:80282000, desc_dma_buf:80281f9c 
PrepareRXBD88XX(225): pdesc_dma_buf:a0282000 
PrepareTXBD88XX(528), q_num:0, TXBD_RWPtr_Reg:3b0, TXBD_Reg:310, a0282400
PrepareTXBD88XX(528), q_num:1, TXBD_RWPtr_Reg:3ac, TXBD_Reg:330, a0282c00
PrepareTXBD88XX(528), q_num:2, TXBD_RWPtr_Reg:3a8, TXBD_Reg:328, a0283400
PrepareTXBD88XX(528), q_num:3, TXBD_RWPtr_Reg:3a4, TXBD_Reg:320, a0285400
PrepareTXBD88XX(528), q_num:4, TXBD_RWPtr_Reg:3a0, TXBD_Reg:318, a0285c00
PrepareTXBD88XX(528), q_num:5, TXBD_RWPtr_Reg:3b8, TXBD_Reg:340, a0286400
PrepareTXBD88XX(528), q_num:6, TXBD_RWPtr_Reg:3bc, TXBD_Reg:348, a0286c00
PrepareTXBD88XX(528), q_num:7, TXBD_RWPtr_Reg:3c0, TXBD_Reg:350, a0287400
PrepareTXBD88XX(528), q_num:8, TXBD_RWPtr_Reg:3c4, TXBD_Reg:358, a0287c00
PrepareTXBD88XX(528), q_num:9, TXBD_RWPtr_Reg:3c8, TXBD_Reg:360, a0288400
PrepareTXBD88XX(528), q_num:10, TXBD_RWPtr_Reg:3cc, TXBD_Reg:368, a0288c00
PrepareTXBD88XX(528), q_num:11, TXBD_RWPtr_Reg:3d0, TXBD_Reg:370, a0288c00
PrepareTXBD88XX(528), q_num:12, TXBD_RWPtr_Reg:3d4, TXBD_Reg:378, a0288c00
PrepareTXBD88XX(528), q_num:13, TXBD_RWPtr_Reg:0, TXBD_Reg:308, a0290e00
Warning: request_irq is used! irq21
25M....
InitPON OK
InitMAC OK
InitHCIDMAReg OK
Get MP MAC_REG Len 
Select MP MAC_REG 
phy_BB88XX_Config_ParaFile(4855), HAL PHY_ConfigBBWithParaFile
[PHY_ConfigBBWithParaFile][PHY_REG_HAL]
Get MP PHY_REG Len 
Slecct MP PHY_REG 
[PHY_ConfigBBWithParaFile][PHY_REG_PG_HAL]
Get MP REG_PG len 
select MP REG_PG 
[PHY_ConfigBBWithParaFile][AGC_TAB_HAL]
Get MP AGC_TAB len 
Select MP AGC_TAB 
Get MP Radio A len 
select MP Radio A 
[phy_RF6052_Config_ParaFile][RadioA_HAL]
Get MP Radio B len 
select MP Radio B 
[phy_RF6052_Config_ParaFile][RadioB_HAL]
InitDownload FW OK 
errorFlag:00000000 
[PHY_ConfigTXPwrTrackingWithParaFile][REG_TXPWR_TRK_8192E]

DO 8192E IQK !!!!
Done 8192E IQK !!!!

Do 8192E LCK!! RF 0xB6 = 0x8046
8192E LCK done!!
wlan_itf_start>open wlan idx=0 successfully
disable idx=1
disable idx=2
disable idx=3
disable idx=4
disable idx=5
Set root WPA PSK = xxxxxxxx
802.1x daemon: open interface 0
IEEE 802.1x (WPA) daemon, version 1.7f
802.1x daemon: open interface 0
IEEE 802.1x (WPA) daemon, version 1.7f
a[wsc]wsc_main 5706:daemon parameter:
brgForwardInit
*******ipv6Init2() Start*******
ipv6_IfInit:ifport=l0, adminStatus=0
ipv6_IfInit:ifport=e1, adminStatus=1
ipv6_IfInit:ifport=w1, adminStatus=1
ipv6_IfInit:ifport=w2, adminStatus=0
ipv6_IfInit:ifport=w3, adminStatus=0
ipv6_IfInit:ifport=w4, adminStatus=0
ipv6_IfInit:ifport=w5, adminStatus=0
ipv6_IfInit:ifport=w6, adminStatus=0
getconfig:ifp=e1
g_prefix_filter=0
*******ipv6Init2() End********
uthRecommand string: dump 
"dump" command: No change mode
gis29242
command string: show mib 
"show" command: No change mode
tLinkUpIpv6:ifindex=10
dhcp: port10 up
port 10 is up

erE/A
POL:b i
alren/adwsy regicstered
d
802.1x daemon: open interface 0
IEEE 802.1x (WPA) daemon, version 1.7f
au thRegis-terEAsPOLtWrong dns server address!
Wrong dns server address!
Wrong dns server address!

dns cache rehash:size=150,new_size=64
llmnr_hostname1:9=>tew-731br
llmnr_hostname2:10=>tew-731br.
: already registered
802.1x daemon: open interface 0
IEEE 802.1x (WPA) daemon, version 1.7f
aauthRegisterEAPOL: already registered
802.1x daemon: open interface 0
IEEE 802.1x (WPA) daemon, version 1.7f
authRegisterEAPOL: already registered
802.1x daemon: open interface 0
IEEE 802.1x (WPA) daemon, version 1.7f
rauthRegisterEAPOL: already registered
t -c /vUars/wsecdr.confn -wa wlman0e -:fi  /var/wscd-wlan0.fifo -debug 
----->parse_argument
Writing file /var/wscd.conf...
----->read_config_file
Read config file[/var/wscd.conf], def=0 
[wsc]read_config_file 4732:auth_type:0x01
[wsc]read_config_file 4764:encrypt_type_flash:1
[wsc]read_config_file 4765:encrypt_type:1
[wsc]read_config_file 4903:network_key=xxxxxxxx
[wsc]read_config_file 4745:auth_type_flags:0x27
[wsc]read_config_file 4777:encrypt_type_flags:15

<<====WPS argument list=====>>
is_ap = 1
role = Registrar
config_state = configured
config_method = 0x2688
pin_code = xxxxxxxx
use_ie = 1
upnp = 1
---wlan0 setting---
rf_band = 1; 1=2.4G ;2=5G
wep_transmit_key = 0
SSID=TRENDnet731_VK7P
Auth Type=1
Encrypt Type=1
WSC_PSK = ""
configured button_hold_time = 1
disable_configured_by_exReg = 0
support EAP_frag reassembly
AP mode; Probe_Rsp wsc_ie frag =false
AP mode;Extension Tag =false
uuid=630412531019200612283c8cf88084c2
auto_lock_down:during[60],fail[3]times,locked[60]seconds
wsc version=2.0

<<====WPS argument list=====>>
pCtx->original_pin_code = 08606402
get_mac_addr>3cffffff8cfffffff8ffffff80ffffff84ffffffc2
[wsc]wsc_main 5770:wlan0 addr: (wsc_main,5771):    3C:8C:F8:80:84:C2
pCtx->upnp:1, wsc_main
<< Start_upnp >>
WSCRegisterCallBackFunc successfully!
mini_UPnP_DeviceStateTableInit 1693:    evnturl_ctrl = /upnp/event/WFAWLANConfig1
mini_UPnP_DeviceStateTableInit 1694:<<===========upnp parameters=================>>


WiFi Simple Config v1.22 (Jul 28 2016).

pidfile_acquire>/var/run/wscd-wlan0.pid
pidfile_write_release>pid_fd:0
----->init_wlan
fixme:open the fifo
[util]build_probe_rsp_ie,3966:config method(0x1008)=2008
wlan0 set_mib wsc_enable=3
wlan0 set_mib func_off=0
init_wlan----->

Initialize PBC station list mutex...
[wsc]wsc_main 5931:alarm(1)---------->
[wsc]sigHandler_pushwpsbutton 4338:pbc pressed time (1), start PBC...
----->process_event
----->evHandler_pb_press
<< Got PB-Pressed event >>
[wsc]evHandler_pb_press 1106:LED START...
[wsc]evHandler_pb_press 1118:update pb_timeout to 120
wsc_system:command echo 0 > /tmp/wscd_status
[util]registrar_remove_all_authorized_mac,172:
[util]registrar_add_authorized_mac,134:
[wsc]evHandler_pb_press 1150:PBC mode update wlan0 IE
[wsc]update_ie 765:

[util]report_authoriedMacCount,185:auth mac:FFFFFF:FFFFFF
[util]report_authoriedMacCount,189:count=1
[util]build_probe_rsp_ie,3966:config method(0x1008)=2008
[util]report_authoriedMacCount,185:auth mac:FFFFFF:FFFFFF
[util]report_authoriedMacCount,189:count=1
OskWlanWscTask: handle CCB_WSC_EVT_DRIVER
wlanIndEvt>wlan_idx=0, data_len=270, pdata=0x8066da64
----->process_event
----->evHandler_probe_req_Ind

<<Got Probe_Req,from Sta(a8a1987acfa0)>>
PROBE_REQUEST WSC IE
    dd 8f 00 50 f2 04 10 4a 00 01 10 10 3a 00 01 00 
    10 08 00 02 42 88 10 47 00 10 ef e8 64 cd b0 bd 
    50 c0 84 8a 5f 9a 8e e8 88 dc 10 54 00 08 00 0a 
    00 50 f2 04 00 05 10 3c 00 01 01 10 02 00 02 00 
    00 10 09 00 02 00 00 10 12 00 02 00 00 10 21 00 
    03 54 43 4c 10 23 00 0d 4f 72 61 6e 67 65 2d 52 
    69 73 65 33 31 10 24 00 0d 4f 72 61 6e 67 65 2d 
    52 69 73 65 33 31 10 11 00 0d 4f 72 61 6e 67 65 
    2d 52 69 73 65 33 31 10 49 00 06 00 37 2a 00 01 
    20 
verdor ext:
    00 37 2a 00 01 20 
[rx]evHandler_probe_req_Ind,1972:Rev version2(0x20) at  ProReq
--------******start ending ****-----
create memory pool: start at 0x80303168, size 19116
Init memory freed, start:80303168, len:19116
OskWlanWscTask: handle CCB_WSC_EVT_DRIVER
wlanIndEvt>wlan_idx=0, data_len=270, pdata=0x803034d4
----->process_event
----->evHandler_probe_req_Ind

<<Got Probe_Req,from Sta(a8a1987acfa0)>>
PROBE_REQUEST WSC IE
    dd 8f 00 50 f2 04 10 4a 00 01 10 10 3a 00 01 00 
    10 08 00 02 42 88 10 47 00 10 ef e8 64 cd b0 bd 
    50 c0 84 8a 5f 9a 8e e8 88 dc 10 54 00 08 00 0a 
    00 50 f2 04 00 05 10 3c 00 01 01 10 02 00 02 00 
    00 10 09 00 02 00 00 10 12 00 02 00 00 10 21 00 
    03 54 43 4c 10 23 00 0d 4f 72 61 6e 67 65 2d 52 
    69 73 65 33 31 10 24 00 0d 4f 72 61 6e 67 65 2d 
    52 69 73 65 33 31 10 11 00 0d 4f 72 61 6e 67 65 
    2d 52 69 73 65 33 31 10 49 00 06 00 37 2a 00 01 
    20 
verdor ext:
    00 37 2a 00 01 20 
[rx]evHandler_probe_req_Ind,1972:Rev version2(0x20) at  ProReq
OskWlanWscTask: handle CCB_WSC_EVT_DRIVER
wlanIndEvt>wlan_idx=0, data_len=270, pdata=0x803034d4
----->process_event
----->evHandler_probe_req_Ind

<<Got Probe_Req,from Sta(84c7ea5e6320)>>
PROBE_REQUEST WSC IE
    dd 78 00 50 f2 04 10 4a 00 01 10 10 3a 00 01 00 
    10 08 00 02 42 88 10 47 00 10 a9 a9 e6 0b 1e cc 
    5b d0 bd 8d 0a a2 0b 96 8b 10 10 54 00 08 00 0a 
    00 50 f2 04 00 05 10 3c 00 01 03 10 02 00 02 00 
    00 10 09 00 02 00 00 10 12 00 02 00 00 10 21 00 
    04 53 6f 6e 79 10 23 00 05 46 33 33 31 31 10 24 
    00 05 46 33 33 31 31 10 11 00 05 46 33 33 31 31 
    10 49 00 06 00 37 2a 00 01 20 
verdor ext:
    00 37 2a 00 01 20 
[rx]evHandler_probe_req_Ind,1972:Rev version2(0x20) at  ProReq
OskWlanWscTask: handle CCB_WSC_EVT_DRIVER
wlanIndEvt>wlan_idx=0, data_len=270, pdata=0x803034d4
----->process_event
----->evHandler_probe_req_Ind

<<Got Probe_Req,from Sta(a8a1987acfa0)>>
PROBE_REQUEST WSC IE
    dd 8f 00 50 f2 04 10 4a 00 01 10 10 3a 00 01 00 
    10 08 00 02 42 88 10 47 00 10 ef e8 64 cd b0 bd 
    50 c0 84 8a 5f 9a 8e e8 88 dc 10 54 00 08 00 0a 
    00 50 f2 04 00 05 10 3c 00 01 01 10 02 00 02 00 
    00 10 09 00 02 00 00 10 12 00 02 00 00 10 21 00 
    03 54 43 4c 10 23 00 0d 4f 72 61 6e 67 65 2d 52 
    69 73 65 33 31 10 24 00 0d 4f 72 61 6e 67 65 2d 
    52 69 73 65 33 31 10 11 00 0d 4f 72 61 6e 67 65 
    2d 52 69 73 65 33 31 10 49 00 06 00 37 2a 00 01 
    20 
verdor ext:
    00 37 2a 00 01 20 
[rx]evHandler_probe_req_Ind,1972:Rev version2(0x20) at  ProReq
OskWlanWscTask: handle CCB_WSC_EVT_DRIVER
wlanIndEvt>wlan_idx=0, data_len=270, pdata=0x803034d4
----->process_event
----->evHandler_probe_req_Ind

<<Got Probe_Req,from Sta(00082230f1fc)>>
PROBE_REQUEST WSC IE
    dd 7e 00 50 f2 04 10 4a 00 01 10 10 3a 00 01 00 
    10 08 00 02 42 88 10 47 00 10 ad ba aa 4c 7e 77 
    5d d4 a0 93 60 dc 73 42 97 22 10 54 00 08 00 0a 
    00 50 f2 04 00 05 10 3c 00 01 01 10 02 00 02 00 
    00 10 09 00 02 00 00 10 12 00 02 00 00 10 21 00 
    03 4a 54 59 10 23 00 06 4b 54 31 30 37 48 10 24 
    00 06 4b 54 31 30 37 48 10 11 00 0a 6b 74 30 39 
    36 68 5f 31 30 31 10 49 00 06 00 37 2a 00 01 20 
verdor ext:
    00 37 2a 00 01 20 
[rx]evHandler_probe_req_Ind,1972:Rev version2(0x20) at  ProReq
PBC walk time-out!
wsc_system:command echo 2 > /tmp/wscd_status
reset_ctx_state 3550 
set pCtx->pin_code = 08606402


    Clear SetSelectedRegistrar flag!!

[util]build_probe_rsp_ie,3966:config method(0x1008)=2008

Same log but with tftp upload.

Booting...

@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@
@ chip__no chip__id mfr___id dev___id cap___id size_sft dev_size chipSize
@ 0000000h 0c22015h 00000c2h 0000020h 0000015h 0000000h 0000015h 0200000h
@ blk_size blk__cnt sec_size sec__cnt pageSize page_cnt chip_clk chipName
@ 0010000h 0000020h 0001000h 0000200h 0000100h 0000010h 000004eh MX25L1605D
@ 
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
 
---RealTek(RTL8196E)at 2013.03.21-09:42+0800 v0.3 [16bit](400MHz)
P0phymode=01, embedded phy

---Ethernet init Okay!
support multicast tool

**TFTP Client Upload, File Name: openwrt-realtek-rtl8196e-AP-fw.bin
-\|/-\|...|/-
**TFTP Client Upload File Size = 003AA004 Bytes at 80500000

Success!
<RealTek>checksum failed  80500000  00009fa5

(Last edited by rdelobel on 10 Dec 2017, 14:55)

rdelobel wrote:

Hello,

I have a Trendnet TEW-731br v3, i'm trying to replace the stock firmware with something else that could allow me to pass an option to the dhcp client (vendor_class_id).
I have successfully build openwrt for realtek 8196e + 8192er (sourceforge.net/projects/rtl819x/).
but i can't get openwrt to be flashed with tftp method, there is a tftp server on 192.168.1.6 that listen when the router start, sending the file with curl -T works but when the router reboot this is still with the stock firmware.

I have started to take a look at the serial connection, the following is the boot log with the stock firmware. For now that's all that I have.

I also have similar device its D-Link DIR 605L same spec, could you share your firmware ? And did you tried to boot it from RAM? Just hit "ESC" after power on and you will be presented with Realtek CLI

@vido

There are two of the firmwares I have build, they don't contain web ui.

drive.google.com/open?id=1PV_FBUeziTsog4Zajvkm1PeJmORiQC6-

Yes I have tried to interrupt the boot process but that did not work, maybe my pins were not all very well soldered.

rdelobel wrote:

@vido

There are two of the firmwares I have build, they don't contain web ui.

drive.google.com/open?id=1PV_FBUeziTsog4Zajvkm1PeJmORiQC6-

Yes I have tried to interrupt the boot process but that did not work, maybe my pins were not all very well soldered.

That's great tnx a lot, Im looking forward to boot them. I downloaded rtl819x SDK from link you provided but I cant get menuconfig to show up Im getting

Error opening terminal: xterm-256color.
Makefile:111: recipe for target 'menuconfig' failed
make: *** [menuconfig] Error 1

What version of linux do you use ? And did you use rtl819x-SDK-v3.4.9.3-full-package-2.tar.gz ?

vido wrote:
Error opening terminal: xterm-256color.
Makefile:111: recipe for target 'menuconfig' failed
make: *** [menuconfig] Error 1

What version of linux do you use ? And did you use rtl819x-SDK-v3.4.9.3-full-package-2.tar.gz ?

I use rtk_openwrtSDK_v2.5 20160905, I'm running a 4.14 kernel, gcc 5.3.0, binutils 2.28 and glibc 2.26, fbdev without X, that's not a distribution. You can use make defconfig_rtl8196e, maybe try to modify the TERM envvar (export TERM=xterm).

rdelobel wrote:
vido wrote:
Error opening terminal: xterm-256color.
Makefile:111: recipe for target 'menuconfig' failed
make: *** [menuconfig] Error 1

What version of linux do you use ? And did you use rtl819x-SDK-v3.4.9.3-full-package-2.tar.gz ?

I use rtk_openwrtSDK_v2.5 20160905, I'm running a 4.14 kernel, gcc 5.3.0, binutils 2.28 and glibc 2.26, fbdev without X, that's not a distribution. You can use make defconfig_rtl8196e, maybe try to modify the TERM envvar (export TERM=xterm).

Great, tnx a lot smile In good health

So I did compile firmware but Im missing IPCONFIG on my boot loader, I did tried 192.168.1.6 but that did not work, I have DIR 605L HW:B2. Is there any other way to flash it or thats it ? Its to scary for me to mess with bootloader.

Does anyone know if there has been any efforts to merge the RTK support back into mainline/LEDE? (Honestly, I'm not even sure what the status of the LEDE-OpenWRT merge is.

I was able to use the RTL819X builds to reasonable success, but they're just against such old versions of OpenWRT, and more and more cheap routers are coming out with the RTL819X chipsets.  I'm really hoping that monitor mode becomes available too.  I've got an RTL8881 router as well as an RTL8197D sitting here on my desk.

The OpenWrt/ LEDE merge, as far as the code base is concerned, is complete. Merging the infrastructure (forum/ wiki, mailing lists, etc.) is in progress, although this aspect won't be completed quickly.

In terms of lexra (Realtek's reduced mips ISA) support, there is none - nor anyone actively pushing for it (as in providing patches/ pull requests against current master); chances for this to change are non-zero, but extremely low (once you'd have hypothetical lexra arch/ SOC support, there would still be the problem of the wlan drivers and current hostapd/ nl80211, to drive them reliably in AP mode).

[Disclaimer: I can't speak for the LEDE/ OpenWrt developers]
Personally I don't think lexra will 'ever' be supported in LEDE/ OpenWrt (too different from normal mips, no upstream/ toolchain support at all, very low-end devices, the wlan situation (drivers, AP mode reliability, nl80211 support) is difficult). But effectively all it would need, is someone pushing for it - to provide a (long-term-) manageable pull request with lexra support against OpenWrt/ master, kernel 4.14, musl, hostapd/ nl80211 for the wlan drivers and not too many arch specific changes (so it can be reasonably updated with the rest of OpenWrt and not stay behind).

(Last edited by slh on 11 Feb 2018, 09:21)

Hi,
how you manage to compile openwrtSDK ?
I tested many versions but all ends up with that error:
"fixdep: error opening depfile: kernel/.bounds.s.d: No such file or directory"
I tested on Fedora 12,14,15,17.
What could be the problem ?

sanitariu wrote:

Hi,
how you manage to compile openwrtSDK ?
...

I am on Ubuntu 16.04 x64 - all is fine. May your sdk has issues?

The discussion might have continued from here.