Hi,
I've already installed uboot and openwrt from wiki. Installation went ok. I'm logging via eht to ssh.
But now I dont see my wlan.
br-lan Link encap:Ethernet HWaddr 16:DE:83:F5:90:53
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::14de:83ff:fef5:9053/64 Scope:Link
inet6 addr: fdc2:744a:8306::1/60 Scope:Global
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:8355 errors:0 dropped:0 overruns:0 frame:0
TX packets:8908 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:867032 (846.7 KiB) TX bytes:3600148 (3.4 MiB)
eth0 Link encap:Ethernet HWaddr 16:DE:83:F5:90:53
inet6 addr: fe80::14de:83ff:fef5:9053/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:8461 errors:0 dropped:0 overruns:0 frame:0
TX packets:8852 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1094005 (1.0 MiB) TX bytes:3673676 (3.5 MiB)
eth0.1 Link encap:Ethernet HWaddr 16:DE:83:F5:90:53
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:8445 errors:0 dropped:0 overruns:0 frame:0
TX packets:8845 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:873102 (852.6 KiB) TX bytes:3594050 (3.4 MiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:16224 errors:0 dropped:0 overruns:0 frame:0
TX packets:16224 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1103904 (1.0 MiB) TX bytes:1103904 (1.0 MiB)
Log from system:
ROM VER: ÉHř
U-Boot 2014.01-openwrt2 (Nov 15 2014 - 14:05:27) P-2812HNU-Fx
Board: ZyXEL P-2812HNU-Fx
SoC: Lantiq VRX288 v1.1
CPU: 500 MHz
IO: 250 MHz
BUS: 250 MHz
BOOT: NOR
DRAM: 128 MiB
Flash: 8 MiB
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: ltq-eth
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x0, size 0x200000
2097152 bytes read: OK
## Booting kernel from Legacy Image at 80800000 ...
Image Name: MIPS OpenWrt Linux-3.18.6
Created: 2015-02-10 21:24:33 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1631904 Bytes = 1.6 MiB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.18.6 (sylwek@WRT) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r44367) ) #5 Tue Feb 10 22:22:40 CET 2015
[ 0.000000] SoC: VR9 rev 1.1
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019555 (MIPS 34Kc)
[ 0.000000] MIPS: machine is P2812HNUF3 - ZyXEL P-2812HNU-F3
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00024202
[ 0.000000] Readback ErrCtl register=00024202
[ 0.000000] Memory: 124780K/131072K available (3494K kernel code, 147K rwdata, 1024K rodata, 180K init, 206K bss, 6292K reserved)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 500MHz
[ 0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[ 0.032000] pid_max: default: 32768 minimum: 301
[ 0.036000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.044000] pinctrl core: initialized pinctrl subsystem
[ 0.048000] NET: Registered protocol family 16
[ 0.056000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[ 0.064000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[ 0.068000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[ 0.072000] MEM 0x0000000018000000..0x0000000019ffffff
[ 0.076000] IO 0x000000001ae00000..0x000000001affffff
[ 0.200000] gpio-stp-xway 1e100bb0.stp: Init done
[ 0.204000] usbcore: registered new interface driver usbfs
[ 0.208000] usbcore: registered new interface driver hub
[ 0.212000] usbcore: registered new device driver usb
[ 0.216000] PCI host bridge to bus 0000:00
[ 0.220000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[ 0.224000] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 0.228000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.232000] PCI host bridge to bus 0000:01
[ 0.236000] pci_bus 0000:01: root bus resource [mem 0x1c000000-0x1cffffff]
[ 0.240000] pci_bus 0000:01: root bus resource [io 0x1d800000-0x1d8fffff]
[ 0.244000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.248000] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
[ 0.260000] ifx_pcie_fixup_resource: fixup host controller 0000:01:00.0 (15d1:0011)
[ 0.264000] pci 0000:01:00.0: Primary bus is hard wired to 0
[ 0.268000] pci 0000:01:00.0: bridge configuration invalid ([bus 01-ff]), reconfiguring
[ 0.272000] pci 0000:01:00.0: PCI bridge to [bus 02]
[ 0.276000] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1
[ 0.280000] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
[ 0.284000] Switched to clocksource MIPS
[ 0.288000] NET: Registered protocol family 2
[ 0.292000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.300000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.308000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.312000] TCP: reno registered
[ 0.316000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.320000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.328000] NET: Registered protocol family 1
[ 0.332000] gptu: totally 6 16-bit timers/counters
[ 0.336000] gptu: misc_register on minor 63
[ 0.344000] gptu: succeeded to request irq 126
[ 0.348000] gptu: succeeded to request irq 127
[ 0.352000] gptu: succeeded to request irq 128
[ 0.356000] gptu: succeeded to request irq 129
[ 0.360000] gptu: succeeded to request irq 130
[ 0.364000] gptu: succeeded to request irq 131
[ 0.368000] ralink,eeprom ralink_eep: using RT3092.eeprom as eeprom
[ 0.376000] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a1x.bin
[ 0.384000] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 7940000
[ 0.388000] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 7940000
[ 0.496000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.528000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.532000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.544000] msgmni has been set to 243
[ 0.548000] io scheduler noop registered
[ 0.552000] io scheduler deadline registered (default)
[ 0.556000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[ 0.564000] console [ttyLTQ0] enabled
[ 0.564000] console [ttyLTQ0] enabled
[ 0.572000] bootconsole [early0] disabled
[ 0.572000] bootconsole [early0] disabled
[ 0.584000] lantiq nor flash device: 00800000 at 10000000
[ 0.588000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[ 0.596000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.600000] Amd/Fujitsu Extended Query version 1.1.
[ 0.604000] number of CFI chips: 1
[ 0.608000] 3 ofpart partitions found on MTD device ltq_nor
[ 0.616000] Creating 3 MTD partitions on "ltq_nor":
[ 0.620000] 0x000000000000-0x000000050000 : "uboot"
[ 0.624000] 0x000000050000-0x000000060000 : "uboot-env"
[ 0.632000] 0x000000060000-0x000000800000 : "unused"
[ 0.636000] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
[ 0.636000] nand: Samsung NAND 128MiB 3,3V 8-bit
[ 0.636000] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[ 0.652000] Scanning device for bad blocks
[ 0.740000] 2 ofpart partitions found on MTD device 14000000.nand-parts
[ 0.744000] Creating 2 MTD partitions on "14000000.nand-parts":
[ 0.752000] 0x000000000000-0x000000200000 : "kernel"
[ 0.756000] 0x000000200000-0x000008000000 : "ubi"
[ 0.864000] libphy: lantiq,xrx200-mdio: probed
[ 0.884000] net-xrx200: invalid MAC, using random
[ 0.948000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:00, irq=-1)
[ 1.016000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:01, irq=-1)
[ 1.084000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[ 1.152000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[ 1.220000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:05, irq=-1)
[ 1.228000] wdt 1f8803f0.watchdog: Init done
[ 1.232000] TCP: cubic registered
[ 1.232000] NET: Registered protocol family 17
[ 1.240000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.252000] Bridge firewalling registered
[ 1.256000] 8021q: 802.1Q VLAN Support v1.8
[ 1.264000] UBI: auto-attach mtd4
[ 1.264000] UBI: attaching mtd4 to ubi0
[ 1.456000] UBI: scanning is finished
[ 1.468000] UBI: attached mtd4 (name "ubi", size 126 MiB) to ubi0
[ 1.476000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[ 1.480000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[ 1.488000] UBI: VID header offset: 512 (aligned 512), data offset: 2048
[ 1.496000] UBI: good PEBs: 1008, bad PEBs: 0, corrupted PEBs: 0
[ 1.500000] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.508000] UBI: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 199074563
[ 1.516000] UBI: available PEBs: 0, total reserved PEBs: 1008, PEBs reserved for bad PEB handling: 20
[ 1.524000] UBI: background thread "ubi_bgt0d" sta[ 1.552000] UBIFS: background thread "ubifs_bgt0_0" started, PID 245
[ 1.580000] UBIFS: recovery needed
[ 1.696000] UBIFS: recovery completed
[ 1.696000] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.704000] UBIFS: LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.712000] UBIFS: FS size: 125540352 bytes (119 MiB, 973 LEBs), journal size 9033728 bytes (8 MiB, 71 LEBs)
[ 1.724000] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 1.728000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 75972139-A04E-4250-92A0-2E97F51DCDD9, small LPT model
[ 1.740000] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 1.744000] Freeing unused kernel memory: 180K (80493000 - 804c0000)
procd: Console is alive
procd: - watchdog -
[ 2.112000] SCSI subsystem initialized
[ 2.136000] IFXUSB: ifxusb_hcd: version 3.2 B110801
[ 2.140000] Chip Version :01c0 BurstSize=0
[ 2.744000] IFXUSB: USB core #0 soft-reset
[ 3.048000] IFXUSB: USB core #0 soft-reset
[ 3.052000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[ 3.056000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
[ 3.064000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
[ 3.068000] IFXUSB: Init: Power Port (0)
[ 3.076000] hub 1-0:1.0: USB hub found
[ 3.076000] hub 1-0:1.0: 1 port detected
[ 3.580000] IFXUSB: USB core #1 soft-reset
[ 3.884000] IFXUSB: USB core #1 soft-reset
[ 3.888000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[ 3.892000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 2
[ 3.900000] ifxusb_hcd ifxusb_hcd: irq 91, io mem 0xbe106000
[ 3.904000] IFXUSB: Init: Power Port (0)
[ 3.912000] hub 2-0:1.0: USB hub found
[ 3.912000] hub 2-0:1.0: 1 port detected
[ 3.916000] ifxusb_hcd ifxusb_hcd: requested GPIO 489
[ 3.932000] usbcore: registered new interface driver usb-storage
procd: - preinit -
[ 4.248000] random: mktemp urandom read with 16 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
mounting /dev/root
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 9.756000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH
[ 9.864000] NET: Registered protocol family 10
[ 9.884000] NET: Registered protocol family 8
[ 9.888000] NET: Registered protocol family 20
[ 9.904000] PPP generic driver version 2.4.2
[ 9.920000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 9.964000] MEI CPE Driver, Version 1.2.0
[ 9.968000] (c) Copyright 2009, Infineon Technologies AG
### MEI CPE - MEI CPE - MEI CPE - MEI CPE ###
Lantiq CPE API Driver version: DSL CPE API V4.11.4
[ 10.024000]
[ 10.024000] Predefined debug level: 2
[ 10.036000] Loading modules backported from Linux version master-2014-11-04-0-gf3660a2
[ 10.044000] Backport generated by backports.git backports-20141023-2-g4ff890b
[ 10.056000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.068000] Infineon Technologies DEU driver version 2.0.0
[ 10.076000] IFX DEU DES initialized (multiblock).
[ 10.080000] IFX DEU AES initialized (multiblock).
[ 10.084000] IFX DEU ARC4 initialized (multiblock).
[ 10.088000] IFX DEU SHA1 initialized.
[ 10.092000] IFX DEU MD5 initialized.
[ 10.096000] IFX DEU SHA1_HMAC initialized.
[ 10.100000] IFX DEU MD5_HMAC initialized.
[ 10.124000] nf_conntrack version 0.5.0 (1952 buckets, 7808 max)
[ 10.152000] NET: Registered protocol family 24
[ 10.160000] usbcore: registered new interface driver ums-alauda
[ 10.164000] usbcore: registered new interface driver ums-cypress
[ 10.172000] usbcore: registered new interface driver ums-datafab
[ 10.180000] usbcore: registered new interface driver ums-freecom
[ 10.188000] usbcore: registered new interface driver ums-isd200
[ 10.192000] usbcore: registered new interface driver ums-jumpshot
[ 10.200000] usbcore: registered new interface driver ums-karma
[ 10.208000] usbcore: registered new interface driver ums-sddr09
[ 10.216000] usbcore: registered new interface driver ums-sddr55
[ 10.224000] usbcore: registered new interface driver ums-usbat
[ 10.232000] usbcore: registered new interface driver usblp
[ 10.244000] usbcore: registered new interface driver usbserial
[ 10.248000] usbcore: registered new interface driver usbserial_generic
[ 10.256000] usbserial: USB Serial support registered for generic
[ 10.280000] xt_time: kernel timezone is -0000
[ 10.360000] cfg80211: Calling CRDA to update world regulatory domain
[ 10.372000] cfg80211: World regulatory domain updated:
[ 10.376000] cfg80211: DFS Master region: unset
[ 10.380000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 10.388000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.396000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.404000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.412000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.420000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 10.432000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 10.440000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.448000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
/etc/rc.common: line 138: esi: not found
[ 14.136000] PTM 1.0.27 PTM (E1) firmware version 0.30
[ 14.140000] ifxmips_ptm: PTM init succeed
[ 16.180000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 16.196000] device eth0.1 entered promiscuous mode
[ 16.200000] device eth0 entered promiscuous mode
[ 16.216000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
procd: - init complete -
[ 31.852000] random: nonblocking pool is initialized
BusyBox v1.22.1 (2015-02-10 16:03:09 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
CHAOS CALMER (Bleeding Edge, r44367)
-----------------------------------------------------
* 1 1/2 oz Gin Shake with a glassful
* 1/4 oz Triple Sec of broken ice and pour
* 3/4 oz Lime Juice unstrained into a goblet.
* 1 1/2 oz Orange Juice
* 1 tsp. Grenadine Syrup
-----------------------------------------------------
root@OpenWrt:/#
root@OpenWrt:/#
I've read another posts where logs were included. And there at the end of logs there was (logs form DGDodo, page 9, post 210:
[ 11.608000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[ 11.612000] rt2800pci 0000:00:0e.0: failed to load eeprom property
[ 11.616000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT3062.eeprom'.
[ 11.628000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3572, rev 0223 detected
[ 11.636000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected
In my log I don't see that.
lsmodshows that rt2800 and rt2x00 load correctly:
rt2800lib 94593 2 rt2800pci
rt2800mmio 7234 1 rt2800pci
rt2800pci 1522 0
rt2x00lib 37455 5 rt2800pci
rt2x00mmio 1968 2 rt2800pci
rt2x00pci 1522 1 rt2800pci
I have F3, and images from scapi's github Chaos Calmer.
BTW. Which package contains lspci?
EDIT:
lspci shows:
01:00.0 PCI bridge: Infineon Technologies AG Device 0011 (rev 01) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 144
Memory at <unassigned> (32-bit, non-prefetchable) [size=2]
Memory at <unassigned> (32-bit, non-prefetchable) [size=2]
Bus: primary=01, secondary=02, subordinate=02, sec-latency=0
Expansion ROM at <unassigned> [disabled] [size=2]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
Capabilities: [70] Express Root Port (Slot-), MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Power Budgeting <?>
lspci -vv:
01:00.0 PCI bridge: Infineon Technologies AG Device 0011 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 144
Region 0: Memory at <unassigned> (32-bit, non-prefetchable) [size=2]
Region 1: Memory at <unassigned> (32-bit, non-prefetchable) [size=2]
Bus: primary=01, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
Expansion ROM at <unassigned> [disabled] [size=2]
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [70] Express (v2) Root Port (Slot-), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <64us
ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- DLActive+ BWMgmt- ABWMgmt-
RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+ RxOF+ MalfTLP+ ECRC+ UnsupReq+ ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap+ CGenEn+ ChkCap+ ChkEn+
Capabilities: [140 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [160 v1] Power Budgeting <?>
and dmesg | grep pci:
[ 0.068000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[ 0.220000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[ 0.224000] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 0.228000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.232000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.236000] pci_bus 0000:01: root bus resource [mem 0x1c000000-0x1cffffff]
[ 0.240000] pci_bus 0000:01: root bus resource [io 0x1d800000-0x1d8fffff]
[ 0.244000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.248000] pci 0000:01:00.0: [15d1:0011] type 01 class 0x060000
[ 0.248000] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
[ 0.260000] ifx_pcie_fixup_resource: fixup host controller 0000:01:00.0 (15d1:0011)
[ 0.264000] pci 0000:01:00.0: PME# supported from D0 D3hot
[ 0.264000] pci 0000:01:00.0: Primary bus is hard wired to 0
[ 0.268000] pci 0000:01:00.0: bridge configuration invalid ([bus 01-ff]), reconfiguring
[ 0.272000] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 0.272000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 02
[ 0.272000] pci 0000:01:00.0: PCI bridge to [bus 02]
[ 0.276000] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1
[ 0.280000] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
So my wifi is not recognizable? There are also some memory problems.
(Last edited by calvxrr on 7 Mar 2015, 15:13)