Hello @all,

i got this device for testing. Now as the NDA is over i am allowed to write about it.

So far this is a new VDSL Router, based on OpenWRT AA.

Specs:
http://www.netgear.com/home/products/ne … -techspecs

Interesting Key Features: Open Source support on www.myopenrouter.com

When i am at home a can post some Logs and stuff (what should i post?)

My personal impression from the beta: Nice piece of hardware. Not so nice piece of software (compared to pure OpenWRT). Performance was nice and stable.

In trunk r48360 this device is supported.

VDSL not working.

WLAN working.

Testing other features now.

USB is not working

Can i somehow help to debug the problem with usb? I'm not a dev, but a know how to compile openwrt and are wiling to test a patch and give feedback.
Would be nice

anyone???

Does VDSL2 work on this yet? If it does, I could be willing to purchase one and try lend a hand?

VDSL has no priority for me, because my ISP don't allow other modems. so i use the isp modem and the nighthawk as router/gateway/access point.
as far as i know vdsl doesn't work.
i think the only commit so far was the initial support commit for this router and since then noone commited any new patch for vdsl or usb or anything else.

any update on this?

any update？ i already update ，if u set password of wifi， it will unsteady。

Hi to all, I just bought this router and got some informations about flashing openwrt in it.
I started with the DD trunk image and I flashed it correctly, i can loging in by using ssh and then install luci GUI, but there are some problems with that trunk image because I can only use and configure the LAN switch to get online on internet to download packages(by using another router that assign, using DHCP enabled on the SWITCH, an IP and i connect to that IP by using ssh), when I downloaded LUCI and  I went in the Interfaces tab, WAN interface show me only sent data but no data received, i tried to connect WAN interface to several other routers with DHCP enabled and also static IP(WAN side) but I see only sent data but not received data on that WAN interface.
The other problem is that all wireless interfaces(2.4 and 5 Ghz) are down, ifconfig doesn't show me any usable wlan interface so no wireless support in the DD trunk.
The DSL modem lantiq doesn't work(no interface rj11 is showed in ifconfig output).
I saw from Netgear source code that the original firmware is based on Attitude Adjustment openwrt, can someone use part of the Source Code(like ADSL modem modules(lantiq), wireless modules SWITCH and WAN modules) to build a special DD trunk with those modules that don't allow the d7800 to work propely?
Please help all d7800 to get this BEST firmware working on that nice pice of hardware!
Thanks to all who can help us!
best regards Emanuele

(Last edited by slimshady984 on 28 Nov 2016, 18:27)

i'm using latest lede and wlan is working

Did you install luci? I can't see the tab menu. Then is your Wan interface working with that firmware?

i just reinstall lede firmware as you told me, i have got the same problems i wrote at the beginning of my posts, no want traffic received only sent traffic in the statistics of my WAN interface, here is the kernel log with some errors at the end, can someone help me?

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.4.32 (buildbot@builds) (gcc version 5.4.0 (LEDE GCC 5.4.0 r2244) ) #0 SMP Mon Nov 28 12:15:13 2016
[    0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] Machine model: Netgear Nighthawk X4 D7800
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 57344
[    0.000000] free_area_init_node: node 0, pgdat c07e7480, node_mem_map cde39000
[    0.000000]   Normal zone: 448 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 57344 pages, LIFO batch:15
[    0.000000] PERCPU: Embedded 11 pages/cpu @cde12000 s13824 r8192 d23040 u45056
[    0.000000] pcpu-alloc: s13824 r8192 d23040 u45056 alloc=11*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 56896
[    0.000000] Kernel command line: rootfstype=squashfs noinitrd
[    0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 220696K/229376K available (4224K kernel code, 245K rwdata, 1540K rodata, 224K init, 227K bss, 8680K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xce800000 - 0xff800000   ( 784 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xce000000   ( 224 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0208000 - 0xc07a95f8   (5766 kB)
[    0.000000]       .init : 0xc07aa000 - 0xc07e2000   ( 224 kB)
[    0.000000]       .data : 0xc07e2000 - 0xc081f5c0   ( 246 kB)
[    0.000000]        .bss : 0xc0822000 - 0xc085af40   ( 228 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[    0.000006] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[    0.000017] Switching to timer-based delay loop, resolution 160ns
[    0.000180] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[    0.000203] pid_max: default: 32768 minimum: 301
[    0.000301] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000316] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000858] CPU: Testing write buffer coherency: ok
[    0.001194] Setting up static identity map for 0x42208280 - 0x422082d8
[    0.004241] Brought up 2 CPUs
[    0.004258] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[    0.004268] CPU: All CPU(s) started in SVC mode.
[    0.013153] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[    0.013382] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.013507] pinctrl core: initialized pinctrl subsystem
[    0.014857] NET: Registered protocol family 16
[    0.015146] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.041421] cpuidle: using governor ladder
[    0.072439] cpuidle: using governor menu
[    0.084472] gpiochip_add: registered GPIOs 0 to 68 on device: 800000.pinmux
[    0.084495] GPIO chip 800000.pinmux: created GPIO range 0->68 ==> 800000.pinmux PIN 0->68
[    0.086107] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
[    0.126646] pps_core: LinuxPPS API ver. 1 registered
[    0.126661] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.126706] PTP clock support registered
[    0.127932] clocksource: Switched to clocksource dg_timer
[    0.129132] NET: Registered protocol family 2
[    0.129683] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.129715] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[    0.129746] TCP: Hash tables configured (established 2048 bind 2048)
[    0.129791] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.129814] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.130007] NET: Registered protocol family 1
[    0.130081] PCI: CLS 0 bytes, default 64
[    0.131345] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.131441] No memory allocated for crashlog
[    0.138413] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.138432] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.141230] io scheduler noop registered
[    0.141250] io scheduler deadline registered (default)
[    0.142571] qcom-pcie 1b500000.pci: GPIO lookup for consumer perst
[    0.142588] qcom-pcie 1b500000.pci: using device tree for GPIO lookup
[    0.142612] of_get_named_gpiod_flags: parsed 'perst-gpios' property of node '/soc/pci@1b500000[0]' - status (0)
[    0.142682] 1b500000.pci supply vdda not found, using dummy regulator
[    0.142769] 1b500000.pci supply vdda_phy not found, using dummy regulator
[    0.142840] 1b500000.pci supply vdda_refclk not found, using dummy regulator
[    0.143219] PCI host bridge /soc/pci@1b500000 ranges:
[    0.143256]    IO 0x0fe00000..0x0fefffff -> 0x0fe00000
[    0.143278]   MEM 0x08000000..0x0fdfffff -> 0x08000000
[    0.175957] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[    0.175977] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.175996] pci_bus 0000:00: root bus resource [io  0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
[    0.176010] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[    0.176025] pci_bus 0000:00: scanning bus
[    0.176070] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
[    0.176175] pci 0000:00:00.0: calling pci_fixup_ide_bases+0x0/0x44
[    0.176228] pci 0000:00:00.0: supports D1
[    0.176243] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    0.176263] pci 0000:00:00.0: PME# disabled
[    0.176497] pci_bus 0000:00: fixups for bus
[    0.176523] PCI: bus0: Fast back to back transfers disabled
[    0.176541] pci 0000:00:00.0: scanning [bus 01-01] behind bridge, pass 0
[    0.176672] pci_bus 0000:01: scanning bus
[    0.176815] pci 0000:01:00.0: [168c:0040] type 00 class 0x028000
[    0.177133] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    0.177497] pci 0000:01:00.0: calling pci_fixup_ide_bases+0x0/0x44
[    0.177875] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    0.177913] pci 0000:01:00.0: PME# disabled
[    0.178268] pci_bus 0000:01: fixups for bus
[    0.178341] PCI: bus1: Fast back to back transfers disabled
[    0.178355] pci_bus 0000:01: bus scan returning with max=01
[    0.178375] pci 0000:00:00.0: scanning [bus 01-01] behind bridge, pass 1
[    0.178394] pci_bus 0000:00: bus scan returning with max=01
[    0.178469] pci 0000:00:00.0: fixup irq: got 133
[    0.178482] pci 0000:00:00.0: assigning IRQ 133
[    0.178544] pci 0000:01:00.0: fixup irq: got 133
[    0.178557] pci 0000:01:00.0: assigning IRQ 133
[    0.178619] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[    0.178642] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[    0.178746] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.178768] pci 0000:00:00.0:   bridge window [mem 0x08000000-0x081fffff]
[    0.179108] aer 0000:00:00.0:pcie02: service driver aer loaded
[    0.179352] qcom-pcie 1b700000.pci: GPIO lookup for consumer perst
[    0.179366] qcom-pcie 1b700000.pci: using device tree for GPIO lookup
[    0.179389] of_get_named_gpiod_flags: parsed 'perst-gpios' property of node '/soc/pci@1b700000[0]' - status (0)
[    0.179460] 1b700000.pci supply vdda not found, using dummy regulator
[    0.179546] 1b700000.pci supply vdda_phy not found, using dummy regulator
[    0.179616] 1b700000.pci supply vdda_refclk not found, using dummy regulator
[    0.179957] PCI host bridge /soc/pci@1b700000 ranges:
[    0.179988]    IO 0x31e00000..0x31efffff -> 0x31e00000
[    0.180008]   MEM 0x2e000000..0x31dfffff -> 0x2e000000
[    0.209037] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[    0.209056] pci_bus 0001:00: root bus resource [bus 00-ff]
[    0.209070] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[    0.209083] pci_bus 0001:00: scanning bus
[    0.209122] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
[    0.209209] pci 0001:00:00.0: calling pci_fixup_ide_bases+0x0/0x44
[    0.209254] pci 0001:00:00.0: supports D1
[    0.209267] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[    0.209284] pci 0001:00:00.0: PME# disabled
[    0.209505] pci_bus 0001:00: fixups for bus
[    0.209525] PCI: bus0: Fast back to back transfers disabled
[    0.209540] pci 0001:00:00.0: scanning [bus 01-01] behind bridge, pass 0
[    0.209675] pci_bus 0001:01: scanning bus
[    0.209817] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000
[    0.210128] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    0.210491] pci 0001:01:00.0: calling pci_fixup_ide_bases+0x0/0x44
[    0.210870] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[    0.210907] pci 0001:01:00.0: PME# disabled
[    0.211191] pci_bus 0001:01: fixups for bus
[    0.211251] PCI: bus1: Fast back to back transfers disabled
[    0.211264] pci_bus 0001:01: bus scan returning with max=01
[    0.211282] pci 0001:00:00.0: scanning [bus 01-01] behind bridge, pass 1
[    0.211301] pci_bus 0001:00: bus scan returning with max=01
[    0.211346] pcieport 0000:00:00.0: fixup irq: got 133
[    0.211360] pcieport 0000:00:00.0: assigning IRQ 133
[    0.211420] pci 0000:01:00.0: fixup irq: got 133
[    0.211433] pci 0000:01:00.0: assigning IRQ 133
[    0.211496] pci 0001:00:00.0: fixup irq: got 166
[    0.211509] pci 0001:00:00.0: assigning IRQ 166
[    0.211568] pci 0001:01:00.0: fixup irq: got 166
[    0.211580] pci 0001:01:00.0: assigning IRQ 166
[    0.211631] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[    0.211652] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[    0.211753] pci 0001:00:00.0: PCI bridge to [bus 01]
[    0.211771] pci 0001:00:00.0:   bridge window [mem 0x2e000000-0x2e1fffff]
[    0.212086] aer 0001:00:00.0:pcie02: service driver aer loaded
[    0.214245] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[    0.215637] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.218460] msm_serial 16340000.serial: msm_serial: detected port #0
[    0.218559] msm_serial 16340000.serial: uartclk = 1843200
[    0.218621] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 167, base_baud = 115200) is a MSM
[    0.218655] msm_serial: console setup on port #0
[    0.853531] console [ttyMSM0] enabled
[    0.858323] msm_serial: driver initialized
[    0.868431] loop: module loaded
[    0.870331] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1
[    0.870377] nand: AMD/Spansion S34MS01G2
[    0.876974] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.880984] Scanning device for bad blocks
[    1.250301] random: nonblocking pool is initialized
[    1.578849] 10 ofpart partitions found on MTD device qcom-nandc
[    1.578875] Creating 10 MTD partitions on "qcom-nandc":
[    1.583578] 0x000000000000-0x000000c80000 : "qcadata"
[    1.590018] 0x000000c80000-0x000001180000 : "APPSBL"
[    1.595020] 0x000001180000-0x000001200000 : "APPSBLENV"
[    1.600121] 0x000001200000-0x000001340000 : "art"
[    1.605061] 0x000001340000-0x000001480000 : "artbak"
[    1.609960] 0x000001480000-0x000001680000 : "kernel"
[    1.614900] 0x000001680000-0x000003480000 : "ubi"
[    1.619931] 0x000003480000-0x000007900000 : "netgear"
[    1.624525] 0x000007900000-0x000008000000 : "reserve"
[    1.629552] 0x000001480000-0x000003480000 : "firmware"
[    1.635736] no rootfs found after FIT image in "firmware"
[    1.639435] libphy: Fixed MDIO Bus: probed
[    1.644219] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/mdio[0]' - status (0)
[    1.644240] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/mdio[1]' - status (0)
[    1.644258] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/soc/mdio[2]'
[    1.644374] libphy: GPIO Bitbanged MDIO: probed
[    1.670112] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
[    1.904014] stmmac - user ID: 0x10, Synopsys ID: 0x37
[    1.904040]  Ring mode enabled
[    1.908038]  DMA HW capability register supported
[    1.911093]  Enhanced/Alternate descriptors
[    1.915763]     Enabled extended descriptors
[    1.919828]  RX Checksum Offload Engine supported (type 2)
[    1.923924]  TX Checksum insertion supported
[    1.929385]  Wake-Up On Lan supported
[    1.933732]  Enable RX Mitigation via HW Watchdog Timer
[    1.938084] of_get_named_gpiod_flags: can't parse 'link-gpios' property of node '/soc/ethernet@37400000/fixed-link[0]'
[    1.938679] stmmac - user ID: 0x10, Synopsys ID: 0x37
[    1.942326]  Ring mode enabled
[    1.947532]  DMA HW capability register supported
[    1.950583]  Enhanced/Alternate descriptors
[    1.955259]     Enabled extended descriptors
[    1.959314]  RX Checksum Offload Engine supported (type 2)
[    1.963421]  TX Checksum insertion supported
[    1.968872]  Wake-Up On Lan supported
[    1.973228]  Enable RX Mitigation via HW Watchdog Timer
[    1.977433] i2c /dev entries driver
[    1.982995] Speed bin: 0
[    1.985291] PVS bin: 1
[    1.988568] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[    1.990282] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[    1.997576] sdhci: Secure Digital Host Controller Interface driver
[    2.004841] sdhci: Copyright(c) Pierre Ossman
[    2.011095] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.017312] L2 @ QSB rate. Forcing new rate.
[    2.021348] L2 @ 384000 KHz
[    2.025520] CPU0 @ 800000 KHz
[    2.027916] CPU1 @ QSB rate. Forcing new rate.
[    2.031211] CPU1 @ 384000 KHz
[    2.036974] NET: Registered protocol family 10
[    2.039761] NET: Registered protocol family 17
[    2.042837] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    2.047486] 8021q: 802.1Q VLAN Support v1.8
[    2.060177] Registering SWP/SWPB emulation handler
[    2.065894] cpu: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:0, -19
[    2.069455] cpu: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:1, -19
[    2.077715] UBI: auto-attach mtd6
[    2.085095] ubi0: attaching mtd6
[    2.371756] ubi0: scanning is finished
[    2.386088] ubi0: attached mtd6 (name "ubi", size 30 MiB)
[    2.386109] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    2.390532] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    2.397227] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    2.404139] ubi0: good PEBs: 240, bad PEBs: 0, corrupted PEBs: 0
[    2.410916] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    2.417108] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 654115505
[    2.424194] ubi0: available PEBs: 0, total reserved PEBs: 240, PEBs reserved for bad PEB handling: 20
[    2.433269] ubi0: background thread "ubi_bgt0d" started, PID 61
[    2.443117] block ubiblock0_0: created from ubi0:0(rootfs)
[    2.448255] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[    2.453752] hctosys: unable to open rtc device (rtc0)
[    2.471263] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    2.471470] Freeing unused kernel memory: 224K (c07aa000 - c07e2000)
[    2.909095] init: Console is alive
[    2.909226] init: - watchdog -
[    3.529207] usbcore: registered new interface driver usbfs
[    3.529279] usbcore: registered new interface driver hub
[    3.533632] usbcore: registered new device driver usb
[    3.539980] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-keys/wifi[0]' - status (0)
[    3.539996] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-keys/reset[0]' - status (0)
[    3.540011] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-keys/wps[0]' - status (0)
[    3.542816] SCSI subsystem initialized
[    3.546542] libata version 3.00 loaded.
[    3.548890] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x0 impl platform mode
[    3.548924] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
[    3.556851] scsi host0: ahci
[    3.564828] ata1: DUMMY
[    3.569602] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.570276] ehci-platform: EHCI generic platform driver
[    3.579240] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.582028] ohci-platform: OHCI generic platform driver
[    3.688662] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    3.688728] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    3.693268] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x00010010
[    3.700767] xhci-hcd xhci-hcd.0.auto: irq 168, io mem 0x11000000
[    3.710376] hub 1-0:1.0: USB hub found
[    3.715591] hub 1-0:1.0: 1 port detected
[    3.719596] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    3.723179] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    3.728760] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.736889] hub 2-0:1.0: USB hub found
[    3.744665] hub 2-0:1.0: 1 port detected
[    3.748225] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    3.751993] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[    3.757426] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x00010010
[    3.764920] xhci-hcd xhci-hcd.1.auto: irq 169, io mem 0x10000000
[    3.774035] hub 3-0:1.0: USB hub found
[    3.779850] hub 3-0:1.0: 1 port detected
[    3.783509] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    3.787404] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[    3.792831] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.800737] hub 4-0:1.0: USB hub found
[    3.808656] hub 4-0:1.0: 1 port detected
[    3.813070] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/usb1[0]' - status (0)
[    3.813158] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/usb2[0]' - status (0)
[    3.813229] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/power_amber[0]' - status (0)
[    3.813304] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/wan_white[0]' - status (0)
[    3.813372] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/wan_amber[0]' - status (0)
[    3.813438] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/wps[0]' - status (0)
[    3.813507] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/esata[0]' - status (0)
[    3.813574] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/power_white[0]' - status (0)
[    3.813644] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/wifi[0]' - status (0)
[    3.817675] init: - preinit -
[    6.749139] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[    8.030007] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 144
[    8.172091] UBIFS (ubi0:1): recovery needed
[    8.390839] UBIFS (ubi0:1): recovery completed
[    8.390996] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[    8.394179] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    8.402170] UBIFS (ubi0:1): FS size: 23363584 bytes (22 MiB, 184 LEBs), journal size 1142784 bytes (1 MiB, 9 LEBs)
[    8.412066] UBIFS (ubi0:1): reserved for root: 1103519 bytes (1077 KiB)
[    8.422285] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID 5901320B-2F43-4430-84A4-3A269AAA0D60, small LPT model
[    8.436947] mount_root: switching to ubifs overlay
[    8.449123] urandom-seed: Seeding with /etc/urandom.seed
[    8.500533] procd: - early -
[    8.500632] procd: - watchdog -
[    9.145279] procd: - ubus -
[    9.199087] procd: - init -
[    9.373524] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    9.379180] Loading modules backported from Linux version wt-2016-10-03-1-g6fcb1a6
[    9.379207] Backport generated by backports.git backports-20160324-9-g0e38f5c
[    9.404400] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[    9.404484] ath10k_pci 0000:01:00.0: enabling bus mastering
[    9.404940] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[    9.540553] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
[    9.540593] ath10k_pci 0000:01:00.0: Falling back to user helper
[    9.579543] firmware ath10k!pre-cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed
[    9.579896] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/cal-pci-0000:01:00.0.bin failed with error -2
[    9.587425] ath10k_pci 0000:01:00.0: Falling back to user helper
[    9.648913] firmware ath10k!cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed
[    9.855975] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[    9.856013] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[    9.866077] ath10k_pci 0000:01:00.0: firmware ver 10.4.1.00030-1 api 5 features no-p2p crc32 d2901e01
[   11.908293] ath10k_pci 0000:01:00.0: unable to read from the device
[   11.908318] ath10k_pci 0000:01:00.0: could not execute otp for board id check: -110
[   11.913359] ath10k_pci 0000:01:00.0: failed to get board id from otp: -110
[   11.921146] ath10k_pci 0000:01:00.0: could not probe fw (-110)
[   11.928976] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[   11.933837] ath10k_pci 0001:01:00.0: enabling bus mastering
[   11.934387] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   12.070195] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0001:01:00.0.bin failed with error -2
[   12.070238] ath10k_pci 0001:01:00.0: Falling back to user helper
[   12.120130] firmware ath10k!pre-cal-pci-0001:01:00.0.bin: firmware_loading_store: map pages failed
[   12.120461] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/cal-pci-0001:01:00.0.bin failed with error -2
[   12.127998] ath10k_pci 0001:01:00.0: Falling back to user helper
[   12.244372] firmware ath10k!cal-pci-0001:01:00.0.bin: firmware_loading_store: map pages failed
[   12.245474] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[   12.251989] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[   12.264185] ath10k_pci 0001:01:00.0: firmware ver 10.4.1.00030-1 api 5 features no-p2p crc32 d2901e01
[   14.308308] ath10k_pci 0001:01:00.0: unable to read from the device
[   14.308334] ath10k_pci 0001:01:00.0: could not execute otp for board id check: -110
[   14.313377] ath10k_pci 0001:01:00.0: failed to get board id from otp: -110
[   14.321143] ath10k_pci 0001:01:00.0: could not probe fw (-110)
[   14.329779] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.336913] nf_conntrack version 0.5.0 (3451 buckets, 13804 max)
[   14.432128] xt_time: kernel timezone is -0000
[   14.439188] PPP generic driver version 2.4.2
[   14.440726] NET: Registered protocol family 24
[   17.454618] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   19.438715] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[   19.438808] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   20.462767] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[   84.594673] Atheros AR8216/AR8236/AR8316 gpio-0:00: Port 2 is up
[   84.606765] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Down
[  266.063624] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready

i am using it as accesspoint only so i bridged all interfaces and this works flawless. yes i installed luci. what do you mean with "can't see the tab menu"?

Thanks for the answer mate, I meant I have no wireless menu under network tab, I installed wireless-tools package and those ath10k modules are just installed but I can't see any wireless Interface by using ifconfig...I just saw Wan interface can't receive any packet if it is connected to another 100 mb ethernet, it can receive packets only if it is connected to another gigabit interface. Can I use the modules/drivers found in the source code of netgear firmware to build my own dd trunk to get modem wan and wireless work as the firmware based on attitude adjustment? Thank you for the answer cheers from italy

what do you see if you execute the command

wifi status

uci show wireless | grep disabled

Hi,
I have just purchased this router and wish to run OpenWRT on it.  I have cross compiled the sources under macos so am happy to assist with development, however I am new to all this.  I am most interested in getting the ADSL to work, some places say it does, others don't.  Is there a definitive answer as to if this is working yet?
Thanks.

It has a Lantiq VR10(VRX320) xdsl2 modem chipset.

"The DSL firmware contained within the Netgear firmware image is:
dsl_vr10_firmware_xdsl-07.07.04.03.00.07_07.07.01.08.00.01.bin"

So anyone can test the xdsl modem. It would be natural procedure to activate the modem part on D7800,as using only wifi and IP WAN port on it is kind of "retarded", particularly there is R7800 to go with. Not to mention R7800 is cheaper than D7800.

So anyone can shed some light is activating xdsl portion doable on D7800?

I've had a bit more of a play with D7800 and LEDE trunk, see post here: forum.lede-project.org/t/netgear-d7800-build/505/2?u=thejoshw
I may be going down the completely wrong path, however with the knowledge I have gained with the build system I should be able to create packages as required.  If someone can tell me where to start (ie. just make the firmware packages and not the other stuff, please let me know) as it appears there is a lot missing from trunk for the D7800 ADSL.

Hi, i wrote a few months ago, i tried to install the openwrt firmware and also the LEDE firmware on this router but the problem is with the Wlan, i can't see the Wireless tab menu in luci, no wlan card recognized...have you got the same problem?
And at last...when I plug the WAN port of the router to my DSL modem's port(it is a 100Mb fastETH) the DHCP seems not working and doesn't assign to WAN an IP...if I plug WAN interface to a gigabit ETH modem it works, how could it be possible?
Cheers from Italy Roma

Haven't tried the wifi yet, am on the LEDE forums trying to get the DSL to work.  Will check it out next time I flash the modem.

Any update on the D7800 guys? I hate the netgear firmware so can wait to get something new...

Hi guys. Sadly no one replied. I’m struggling with even the basic LAN and I can’t even get any internet connection on either OpenWrt or LEDE. I’ve got a PPPOE internet  provider and I’ve even put PPPOE in LAN and WAN separately and neither work. If anyone with OpenWrt working could send me their settings it would be much appreciated.

Has anyone been able to get DSL working with the later versions of LEDE. It worked fine with the version from My Open Router but I have you to get it connected with the later snapshot builds. I'm incredibly new to this so I have basically no idea what I'm doing but I would love to be able to use the D7800 as a modem/router instead of just a router

The good part, it's a lantiq (PSB80320) ADSL frontend - the bad part, it's just the ADSL frontend without the accompanying lantiq SOC (VRX320), no RAM, no flash, it appears to be driven solely from the IPQ8064 SOC. It doesn't help either that LEDE/ OpenWrt doesn't appear to support lantiq VRX320 in general so far.

While the situation might not be as hopeless as it would be with a broadcom VDSL modem, this particular combination will be anything but easy, with lots of reverse engineering required (getting VRX320 xDSL drivers, investigating how it communicates with the IPQ8064 SOC - and to fix the driver to work in this 'alien' environment). Given that this device seems to be the only one which has chosen this particular combination, finding the manpower to get this done might be a bit harder.

In short, I wouldn't expect this to be supported anytime soon - and it might very well never find the attention needed to become supported either.