OpenWrt Forum Archive

Topic: Blueendless U25AWF - MT7620 Travel Router with Battery and HDD

The content of this topic has been archived between 23 Apr 2018 and 6 May 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

hcdt wrote:

How to paste link here? I am placing all that is after first slash:

/watch?v=0Pfgqp08uTM

Learn how to post using code block for plain text or just post using an URL tag.

Has anyone managed to access the drive over WiFi/LAN while it is plugged into another device (like a TV for instance) via the USB cable?  For me it's one or the other and I'm trying to work out if it's a software limitation or a hardware limitation.

Max108: I think it is a hardware limitation I ask the seller when I test with the original firmware.

I try to compile my own openwrt for this drive because th firmware provide in the first post did not have hard drive support but i always have some error last one is in relation with this patch:
050-gcc-6-compile.patch(sorry could not put the link)

But I did not find this file what did I miss ?

thanks

dangherve wrote:

Max108: I think it is a hardware limitation I ask the seller when I test with the original firmware.

That's a pity, but thanks for the info. Looks like I'm going to have to rethink.

Hi there nice to meet you guys, I'm new here, I've just bought my new U25AWF but wifi won't turn on from new, and the chipset is different MTK MT7620A not N, does anyone here could help find out what's happen with my stuff?

Is that possible to flash firmware via LAN port on U25AWF? since no wifi detection

I installed the later image from the post of prisoner1969 on my Kimax. All went OK, but I did set my Kimax in relay bridged mode and I do not have IP address on the LAN or WLAN interfaces - I do not have access to the web setup anymore!

Apart from that the KIMAX work amazingly well as bridged AP under OpenWRT - gave me 65 M bits/s.

When trying the standard OpenWRT "factory reset" procedure I see the message: "Msg from 192.168.1.1: Please press button now to enter failsafe!" (using recvudp.exe utility) from the Kimax (IP address 192.168.1.1) . Unfortunately when I press the button on the back - nothing happens, the boot process completes and my Kimax goes to a bridge mode.

Any attempts to SSH / TELNET to 192.168.1.1 are not successful.

Please - any help will be highly appreciated. Is there a way to get a serial port  - which pins shall I use?

(Last edited by mg.vassilev on 27 Oct 2016, 20:40)

Kh_Shad wrote:

...OpenWRT Chaos Calmer
I changed all needed file to make firmware using source of Chaos Calmer...

Продолжение будет?
Как роутер работает шикарно.
Но HDD не подключается с этой прошивкой.
Где искать проблему?

Hi all,

I just rewrote the patch and it works with latest openwrt trunk. I also submited pull request at github.com/openwrt/openwrt/pull/380

(Last edited by danman on 8 Feb 2017, 23:21)

here is my compiled binary:
goo.gl/CtK3Bk

the firmware also works on U35WF (MT7620N chipset), both internal drive and externally connected USB drives work OK

I achieved transfer speed 6MB/s via wifi and 8.8MB/s via ether using samba reading from internal SSD

these packages are compiled in:

base-files - 169-50105
block-mount - 2016-07-24-addd7dc21fe99f2701c1d4708071578052af401d
busybox - 1.24.2-1
dnsmasq - 2.76-1
dropbear - 2016.74-1
firewall - 2016-11-29-1
fstools - 2016-07-24-addd7dc21fe99f2701c1d4708071578052af401d
hostapd-common - 2016-06-15-1
ip6tables - 1.4.21-2
iptables - 1.4.21-2
iw - 4.3-1
iwinfo - 2016-01-25-e4aca3910dff532ed878d0ceaf1ab6e8ad7719bf
jshn - 2016-11-29-77a629375d7387a33a59509d9d751a8798134cab
jsonfilter - 2016-07-02-dea067ad67d977c247c300c06676a06adf21e0c7
kernel - 4.4.14-1-bd0a9211d9754d42edfc94ab4f4c9935
kmod-cfg80211 - 4.4.14+2016-05-12-1
kmod-crypto-crc32c - 4.4.14-1
kmod-crypto-hash - 4.4.14-1
kmod-eeprom-93cx6 - 4.4.14-1
kmod-fs-btrfs - 4.4.14-1
kmod-fs-exfat - 4.4.14+2017-01-03-8d291f525ce6d88fe0d8b11b86fd5c2e900401d3-1
kmod-fs-exportfs - 4.4.14-1
kmod-fs-ext4 - 4.4.14-1
kmod-fs-hfs - 4.4.14-1
kmod-fs-hfsplus - 4.4.14-1
kmod-fs-isofs - 4.4.14-1
kmod-fs-msdos - 4.4.14-1
kmod-fs-ntfs - 4.4.14-1
kmod-fs-udf - 4.4.14-1
kmod-fs-vfat - 4.4.14-1
kmod-fs-xfs - 4.4.14-1
kmod-gpio-button-hotplug - 4.4.14-2
kmod-hid - 4.4.14-1
kmod-hid-generic - 4.4.14-1
kmod-input-core - 4.4.14-1
kmod-input-evdev - 4.4.14-1
kmod-ip6tables - 4.4.14-1
kmod-ipt-conntrack - 4.4.14-1
kmod-ipt-core - 4.4.14-1
kmod-ipt-nat - 4.4.14-1
kmod-leds-gpio - 4.4.14-1
kmod-ledtrig-usbdev - 4.4.14-1
kmod-lib-crc-ccitt - 4.4.14-1
kmod-lib-crc-itu-t - 4.4.14-1
kmod-lib-crc16 - 4.4.14-1
kmod-lib-crc32c - 4.4.14-1
kmod-lib-lzo - 4.4.14-1
kmod-lib-raid6 - 4.4.14-1
kmod-lib-xor - 4.4.14-1
kmod-lib-zlib - 4.4.14-1
kmod-mac80211 - 4.4.14+2016-05-12-1
kmod-mt76 - 4.4.14+2016-06-17-1
kmod-nf-conntrack - 4.4.14-1
kmod-nf-conntrack6 - 4.4.14-1
kmod-nf-ipt - 4.4.14-1
kmod-nf-ipt6 - 4.4.14-1
kmod-nf-nat - 4.4.14-1
kmod-nls-base - 4.4.14-1
kmod-nls-cp1250 - 4.4.14-1
kmod-nls-cp1251 - 4.4.14-1
kmod-nls-cp437 - 4.4.14-1
kmod-nls-cp775 - 4.4.14-1
kmod-nls-cp850 - 4.4.14-1
kmod-nls-cp852 - 4.4.14-1
kmod-nls-cp862 - 4.4.14-1
kmod-nls-cp864 - 4.4.14-1
kmod-nls-cp866 - 4.4.14-1
kmod-nls-cp932 - 4.4.14-1
kmod-nls-iso8859-1 - 4.4.14-1
kmod-nls-iso8859-13 - 4.4.14-1
kmod-nls-iso8859-15 - 4.4.14-1
kmod-nls-iso8859-2 - 4.4.14-1
kmod-nls-iso8859-6 - 4.4.14-1
kmod-nls-iso8859-8 - 4.4.14-1
kmod-nls-koi8r - 4.4.14-1
kmod-nls-utf8 - 4.4.14-1
kmod-ppp - 4.4.14-1
kmod-pppoe - 4.4.14-1
kmod-pppox - 4.4.14-1
kmod-rt2800-lib - 4.4.14+2016-05-12-1
kmod-rt2800-mmio - 4.4.14+2016-05-12-1
kmod-rt2800-pci - 4.4.14+2016-05-12-1
kmod-rt2800-soc - 4.4.14+2016-05-12-1
kmod-rt2x00-lib - 4.4.14+2016-05-12-1
kmod-rt2x00-mmio - 4.4.14+2016-05-12-1
kmod-rt2x00-pci - 4.4.14+2016-05-12-1
kmod-scsi-core - 4.4.14-1
kmod-slhc - 4.4.14-1
kmod-tun - 4.4.14-1
kmod-usb-core - 4.4.14-1
kmod-usb-hid - 4.4.14-1
kmod-usb-ohci - 4.4.14-1
kmod-usb-serial - 4.4.14-1
kmod-usb-serial-ark3116 - 4.4.14-1
kmod-usb-serial-belkin - 4.4.14-1
kmod-usb-serial-ch341 - 4.4.14-1
kmod-usb-serial-cp210x - 4.4.14-1
kmod-usb-serial-cypress-m8 - 4.4.14-1
kmod-usb-serial-ftdi - 4.4.14-1
kmod-usb-storage - 4.4.14-1
kmod-usb-storage-extras - 4.4.14-1
kmod-usb2 - 4.4.14-1
libblobmsg-json - 2016-11-29-77a629375d7387a33a59509d9d751a8798134cab
libc - 1.1.16-1
libgcc - 5.3.0-1
libip4tc - 1.4.21-2
libip6tc - 1.4.21-2
libiwinfo - 2016-01-25-e4aca3910dff532ed878d0ceaf1ab6e8ad7719bf
libiwinfo-lua - 2016-01-25-e4aca3910dff532ed878d0ceaf1ab6e8ad7719bf
libjson-c - 0.12-1
libjson-script - 2016-11-29-77a629375d7387a33a59509d9d751a8798134cab
liblua - 5.1.5-1
liblzo - 2.09-1
libnl-tiny - 0.1-5
libubox - 2016-11-29-77a629375d7387a33a59509d9d751a8798134cab
libubus - 2016-07-02-053be7df871e05478284235732f8b0608089512f
libubus-lua - 2016-07-02-053be7df871e05478284235732f8b0608089512f
libuci - 2016-07-04.1-1
libuci-lua - 2016-07-04.1-1
libuclient - 2016-01-28-2e0918c7e0612449024caaaa8d44fb2d7a33f5f3
libxtables - 1.4.21-2
logd - 2016-07-19-aead2c0cbffdda9b46d74a998a4c6aeef423b21a
lua - 5.1.5-1
luci - git-17.038.75609-fecf6e1-1
luci-app-firewall - git-17.038.75609-fecf6e1-1
luci-app-samba - git-17.038.75609-fecf6e1-1
luci-base - git-17.038.75609-fecf6e1-1
luci-lib-ip - git-17.038.75609-fecf6e1-1
luci-lib-jsonc - git-17.038.75609-fecf6e1-1
luci-lib-nixio - git-17.038.75609-fecf6e1-1
luci-mod-admin-full - git-17.038.75609-fecf6e1-1
luci-proto-ipv6 - git-17.038.75609-fecf6e1-1
luci-proto-ppp - git-17.038.75609-fecf6e1-1
luci-theme-bootstrap - git-17.038.75609-fecf6e1-1
mtd - 21
netifd - 2016-12-09-edc15caac6c6d3b2d8ea17f98ecbaba81ba573dc
odhcp6c - 2016-02-08-7533a6243dc3ac5a747cf6ccbc4d0539dafd3e07
odhcpd - 2016-10-09-801cfeea100ca7b211c9841f0fcb757b17f47860
opkg - 9c97d5ecd795709c8584e972bfdf3aee3a5b846d-15
ppp - 2.4.7-9
ppp-mod-pppoe - 2.4.7-9
procd - 2016-07-29-2c9f5d4af1559b840c42f1443ede9f9fe809c58b
rpcd - 2016-06-30-23417e94d25570e6d62542bac46edd51e8e0243a
rt2800-pci-firmware - 2016-01-25-52442afee9907bc32a058f22bb3295d040677c26-1
samba36-server - 3.6.25-5
swconfig - 11
ubox - 2016-07-19-aead2c0cbffdda9b46d74a998a4c6aeef423b21a
ubus - 2016-07-02-053be7df871e05478284235732f8b0608089512f
ubusd - 2016-07-02-053be7df871e05478284235732f8b0608089512f
uci - 2016-07-04.1-1
uclient-fetch - 2016-01-28-2e0918c7e0612449024caaaa8d44fb2d7a33f5f3
uht tpd - 2016-10-05-fe01ef3f52adae9da38ef47926cd50974af5d6b7
uht tpd-mod-ubus - 2016-10-05-fe01ef3f52adae9da38ef47926cd50974af5d6b7
usign - 2016-07-04-ef6419142a3b0fbcddcccf536e3c1880302c6f89
wpad-mini - 2016-06-15-1
zlib - 1.2.8-1

(Last edited by danman on 9 Feb 2017, 13:16)

danman wrote:

here is my compiled binary:
goo.gl/CtK3Bk

Thank you try.
Do I understand correctly, it is a replica of flash memory?
Or, update the firmware?

It's firmware update. Do you need full flash?

Thank you .
There is progress))
Sees FAT32
But SAMBA does not see the partition in NTFS
While SWAP, offers this section for mounting
((

(Last edited by BoS on 11 Feb 2017, 18:05)

what does dmesg say when you try to mount that ntfs partition?

root@qqq:~# dmesg | grep sd
[   13.253515] sd 0:0:0:0: no of_node; not parsing pinctrl DT
[   13.256001] sd 0:0:0:0: [sda] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB)
[   13.271926] sd 0:0:0:0: [sda] Write Protect is off
[   13.281538] sd 0:0:0:0: [sda] Mode Sense: 1f 00 10 08
[   13.282002] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[   13.303383]  sda: sda1 sda2
[   13.312247] sd 0:0:0:0: [sda] Attached SCSI disk
[   18.657458] usbcore: registered new interface driver ums-isd200
[   18.701886] usbcore: registered new interface driver ums-sddr09
[   18.716439] usbcore: registered new interface driver ums-sddr55

(Last edited by BoS on 12 Feb 2017, 22:53)

you are not mounting it...
check in System -> Mount points

danman wrote:

It's firmware update. Do you need full flash?

Hello. Bought kimax u-35wf. Everything works but little speed WiFi (1,5mb / s). Tell me dear danman, your update will help to solve my problem?

danman wrote:

I achieved transfer speed 6MB/s via wifi and 8.8MB/s via ether using samba reading from internal SSD

Hello. Very confused.
I have a BS-25awf CPU mt7602a what firmware openwrt fit? Board U25AWF-7620A-1153-v2.0.

I sorry The situation is this. If  connect directly to Kimaksu via WiFi is the speed of copying from a disc 6.5 Mb / s. If kimah connected to another router through WiFi the speed of the disc has 1.5 Mb / s. At the same time the normal speed of the Internet in both cases (10Mb / s) It is possible as that correct?

danman wrote:

here is my compiled binary:
goo.gl/CtK3Bk

the firmware also works on U35WF (MT7620N chipset), both internal drive and externally connected USB drives work OK

I achieved transfer speed 6MB/s via wifi and 8.8MB/s via ether using samba reading from internal SSD

these packages are compiled in:

base-files - 169-50105
block-mount - 2016-07-24-addd7dc21fe99f2701c1d4708071578052af401d
busybox - 1.24.2-1
dnsmasq - 2.76-1
dropbear - 2016.74-1
firewall - 2016-11-29-1
fstools - 2016-07-24-addd7dc21fe99f2701c1d4708071578052af401d
hostapd-common - 2016-06-15-1
ip6tables - 1.4.21-2
iptables - 1.4.21-2
iw - 4.3-1
iwinfo - 2016-01-25-e4aca3910dff532ed878d0ceaf1ab6e8ad7719bf
jshn - 2016-11-29-77a629375d7387a33a59509d9d751a8798134cab
jsonfilter - 2016-07-02-dea067ad67d977c247c300c06676a06adf21e0c7
kernel - 4.4.14-1-bd0a9211d9754d42edfc94ab4f4c9935
kmod-cfg80211 - 4.4.14+2016-05-12-1
kmod-crypto-crc32c - 4.4.14-1
kmod-crypto-hash - 4.4.14-1
kmod-eeprom-93cx6 - 4.4.14-1
kmod-fs-btrfs - 4.4.14-1
kmod-fs-exfat - 4.4.14+2017-01-03-8d291f525ce6d88fe0d8b11b86fd5c2e900401d3-1
kmod-fs-exportfs - 4.4.14-1
kmod-fs-ext4 - 4.4.14-1
kmod-fs-hfs - 4.4.14-1
kmod-fs-hfsplus - 4.4.14-1
kmod-fs-isofs - 4.4.14-1
kmod-fs-msdos - 4.4.14-1
kmod-fs-ntfs - 4.4.14-1
kmod-fs-udf - 4.4.14-1
kmod-fs-vfat - 4.4.14-1
kmod-fs-xfs - 4.4.14-1
kmod-gpio-button-hotplug - 4.4.14-2
kmod-hid - 4.4.14-1
kmod-hid-generic - 4.4.14-1
kmod-input-core - 4.4.14-1
kmod-input-evdev - 4.4.14-1
kmod-ip6tables - 4.4.14-1
kmod-ipt-conntrack - 4.4.14-1
kmod-ipt-core - 4.4.14-1
kmod-ipt-nat - 4.4.14-1
kmod-leds-gpio - 4.4.14-1
kmod-ledtrig-usbdev - 4.4.14-1
kmod-lib-crc-ccitt - 4.4.14-1
kmod-lib-crc-itu-t - 4.4.14-1
kmod-lib-crc16 - 4.4.14-1
kmod-lib-crc32c - 4.4.14-1
kmod-lib-lzo - 4.4.14-1
kmod-lib-raid6 - 4.4.14-1
kmod-lib-xor - 4.4.14-1
kmod-lib-zlib - 4.4.14-1
kmod-mac80211 - 4.4.14+2016-05-12-1
kmod-mt76 - 4.4.14+2016-06-17-1
kmod-nf-conntrack - 4.4.14-1
kmod-nf-conntrack6 - 4.4.14-1
kmod-nf-ipt - 4.4.14-1
kmod-nf-ipt6 - 4.4.14-1
kmod-nf-nat - 4.4.14-1
kmod-nls-base - 4.4.14-1
kmod-nls-cp1250 - 4.4.14-1
kmod-nls-cp1251 - 4.4.14-1
kmod-nls-cp437 - 4.4.14-1
kmod-nls-cp775 - 4.4.14-1
kmod-nls-cp850 - 4.4.14-1
kmod-nls-cp852 - 4.4.14-1
kmod-nls-cp862 - 4.4.14-1
kmod-nls-cp864 - 4.4.14-1
kmod-nls-cp866 - 4.4.14-1
kmod-nls-cp932 - 4.4.14-1
kmod-nls-iso8859-1 - 4.4.14-1
kmod-nls-iso8859-13 - 4.4.14-1
kmod-nls-iso8859-15 - 4.4.14-1
kmod-nls-iso8859-2 - 4.4.14-1
kmod-nls-iso8859-6 - 4.4.14-1
kmod-nls-iso8859-8 - 4.4.14-1
kmod-nls-koi8r - 4.4.14-1
kmod-nls-utf8 - 4.4.14-1
kmod-ppp - 4.4.14-1
kmod-pppoe - 4.4.14-1
kmod-pppox - 4.4.14-1
kmod-rt2800-lib - 4.4.14+2016-05-12-1
kmod-rt2800-mmio - 4.4.14+2016-05-12-1
kmod-rt2800-pci - 4.4.14+2016-05-12-1
kmod-rt2800-soc - 4.4.14+2016-05-12-1
kmod-rt2x00-lib - 4.4.14+2016-05-12-1
kmod-rt2x00-mmio - 4.4.14+2016-05-12-1
kmod-rt2x00-pci - 4.4.14+2016-05-12-1
kmod-scsi-core - 4.4.14-1
kmod-slhc - 4.4.14-1
kmod-tun - 4.4.14-1
kmod-usb-core - 4.4.14-1
kmod-usb-hid - 4.4.14-1
kmod-usb-ohci - 4.4.14-1
kmod-usb-serial - 4.4.14-1
kmod-usb-serial-ark3116 - 4.4.14-1
kmod-usb-serial-belkin - 4.4.14-1
kmod-usb-serial-ch341 - 4.4.14-1
kmod-usb-serial-cp210x - 4.4.14-1
kmod-usb-serial-cypress-m8 - 4.4.14-1
kmod-usb-serial-ftdi - 4.4.14-1
kmod-usb-storage - 4.4.14-1
kmod-usb-storage-extras - 4.4.14-1
kmod-usb2 - 4.4.14-1
libblobmsg-json - 2016-11-29-77a629375d7387a33a59509d9d751a8798134cab
libc - 1.1.16-1
libgcc - 5.3.0-1
libip4tc - 1.4.21-2
libip6tc - 1.4.21-2
libiwinfo - 2016-01-25-e4aca3910dff532ed878d0ceaf1ab6e8ad7719bf
libiwinfo-lua - 2016-01-25-e4aca3910dff532ed878d0ceaf1ab6e8ad7719bf
libjson-c - 0.12-1
libjson-script - 2016-11-29-77a629375d7387a33a59509d9d751a8798134cab
liblua - 5.1.5-1
liblzo - 2.09-1
libnl-tiny - 0.1-5
libubox - 2016-11-29-77a629375d7387a33a59509d9d751a8798134cab
libubus - 2016-07-02-053be7df871e05478284235732f8b0608089512f
libubus-lua - 2016-07-02-053be7df871e05478284235732f8b0608089512f
libuci - 2016-07-04.1-1
libuci-lua - 2016-07-04.1-1
libuclient - 2016-01-28-2e0918c7e0612449024caaaa8d44fb2d7a33f5f3
libxtables - 1.4.21-2
logd - 2016-07-19-aead2c0cbffdda9b46d74a998a4c6aeef423b21a
lua - 5.1.5-1
luci - git-17.038.75609-fecf6e1-1
luci-app-firewall - git-17.038.75609-fecf6e1-1
luci-app-samba - git-17.038.75609-fecf6e1-1
luci-base - git-17.038.75609-fecf6e1-1
luci-lib-ip - git-17.038.75609-fecf6e1-1
luci-lib-jsonc - git-17.038.75609-fecf6e1-1
luci-lib-nixio - git-17.038.75609-fecf6e1-1
luci-mod-admin-full - git-17.038.75609-fecf6e1-1
luci-proto-ipv6 - git-17.038.75609-fecf6e1-1
luci-proto-ppp - git-17.038.75609-fecf6e1-1
luci-theme-bootstrap - git-17.038.75609-fecf6e1-1
mtd - 21
netifd - 2016-12-09-edc15caac6c6d3b2d8ea17f98ecbaba81ba573dc
odhcp6c - 2016-02-08-7533a6243dc3ac5a747cf6ccbc4d0539dafd3e07
odhcpd - 2016-10-09-801cfeea100ca7b211c9841f0fcb757b17f47860
opkg - 9c97d5ecd795709c8584e972bfdf3aee3a5b846d-15
ppp - 2.4.7-9
ppp-mod-pppoe - 2.4.7-9
procd - 2016-07-29-2c9f5d4af1559b840c42f1443ede9f9fe809c58b
rpcd - 2016-06-30-23417e94d25570e6d62542bac46edd51e8e0243a
rt2800-pci-firmware - 2016-01-25-52442afee9907bc32a058f22bb3295d040677c26-1
samba36-server - 3.6.25-5
swconfig - 11
ubox - 2016-07-19-aead2c0cbffdda9b46d74a998a4c6aeef423b21a
ubus - 2016-07-02-053be7df871e05478284235732f8b0608089512f
ubusd - 2016-07-02-053be7df871e05478284235732f8b0608089512f
uci - 2016-07-04.1-1
uclient-fetch - 2016-01-28-2e0918c7e0612449024caaaa8d44fb2d7a33f5f3
uht tpd - 2016-10-05-fe01ef3f52adae9da38ef47926cd50974af5d6b7
uht tpd-mod-ubus - 2016-10-05-fe01ef3f52adae9da38ef47926cd50974af5d6b7
usign - 2016-07-04-ef6419142a3b0fbcddcccf536e3c1880302c6f89
wpad-mini - 2016-06-15-1
zlib - 1.2.8-1

Dear danman, would be possible to share patch and config files to recompile your work with some small changes I wonder to make?

I received from friends from China new firmware 1.4.0. But the works also. Speed WiFi 1,5 Mb/s

mg.vassilev wrote:

I installed the later image from the post of prisoner1969 on my Kimax. All went OK, but I did set my Kimax in relay bridged mode and I do not have IP address on the LAN or WLAN interfaces - I do not have access to the web setup anymore!

Apart from that the KIMAX work amazingly well as bridged AP under OpenWRT - gave me 65 M bits/s.

When trying the standard OpenWRT "factory reset" procedure I see the message: "Msg from 192.168.1.1: Please press button now to enter failsafe!" (using recvudp.exe utility) from the Kimax (IP address 192.168.1.1) . Unfortunately when I press the button on the back - nothing happens, the boot process completes and my Kimax goes to a bridge mode.

Any attempts to SSH / TELNET to 192.168.1.1 are not successful.

Please - any help will be highly appreciated. Is there a way to get a serial port  - which pins shall I use?

Did you finally solved it? I have similar problem and I do not know what to do.
I read somewhere that it should be possible to connect with TFTP few seconds after router is turned on (during the u-boot start).

Does anybody knows if it is possible?

Also, can anybody post here values of "ipaddr" and "serverip" for u-boot on this device?

Hi. I have a KIMAX U25AWF device. I want to access to root directory for configure some apps on openwrt but I can not find any documantary for know how. Please help me for this proses. How can access to root directory on this device. Thank you for your kindly helps...