OpenWrt Forum Archive

Topic: Update on Linksys WRT1900AC support

The content of this topic has been archived between 16 Sep 2014 and 7 May 2018. Unfortunately there are posts – most likely complete pages – missing.

Post #401
dfarning
15 Jun 2014, 21:54

I was wondering if anyone has an update to the status of the openwrt on WRT1900AC.

I have been using the Belkin branch at https://github.com/jimmychungbelkin/Mamba for a week and am pretty happy.... In my use case it is already quite a bit more usable than the stock firmware installed on the WRT1900AC!

In an interesting related piece of news Marvell released a data sheet on one of their NAS chips.  ( http://linuxgizmos.com/marvell-lifts-cu … r-nas-soc/ )

Is the goal for the Belkin branch to be merged into upstream openwrt or is the openwrt community happening seperately?

In the meantime, should we report issues to https://github.com/jimmychungbelkin/Mamba/issues ?

Thanks

Post #402
jalyst
16 Jun 2014, 05:43

Did anyone else get unsubscribed from this thread after it was moved to this sub-forum?
I only just noticed, luckily...

So nyt, it's now over 2wks???
"Also, you should see some good news in 2-3 weeks, so sit tight."

Post:
https://forum.openwrt.org/viewtopic.php … 14#p235214

(Last edited by jalyst on 16 Jun 2014, 05:46)

Post #403
linuxpro
17 Jun 2014, 05:58

I have board. Name is RTNAS V3
$99

Soc :Marvell armada370 ARMv7 1.2G
Switch: Marvell 88E6171R 100/1000M 5 Port
DDR3 1G or 512MB
NAND FLASH 4GB
SATA2: 2 Port and 12V power Port: 2 socket
Minipci-e: 2 slot (include 4G LTE support)
SIM : 1 socket
GPIO .......


We have port Marvell SDK to OpenWRT....

Samba: read 90MB/s, write 50MB/s
FTP: read 95MB/s, write 55MB/s

NAT: WAN to LAN  931Mbps

WIFI:  WIFI --- LAN--  Samba:  35MB/s (AR9880) ath10k.
WIFI: WIFI---LAN -- Samba: 16MB/s (88W8366) marvell drivers.


PunBB bbcode Board

PunBB bbcode siwtch

PunBB bbcode siwtch

PunBB bbcode siwtch

PunBB bbcode siwtch


PunBB bbcode siwtch


PunBB bbcode siwtch

PunBB bbcode siwtch

Post #404
linuxpro
17 Jun 2014, 05:59

system format is : ubifs.
big_smile

BootROM 1.08
Booting from NAND flash
DDR3 Training Sequence - Ver 4.0.0
DDR3 Training Sequence - Ended Successfully 
Status = MV_OK
BootROM: Image checksum verification PASSED

 __   __                      _ _
|  \/  | __ _ _ ____   _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| |  | | (_| | |   \ V /  __/ | |
|_|  |_|\__,_|_|    \_/ \___|_|_|
         _   _     ____              _
        | | | |   | __ )  ___   ___ | |_ 
        | | | |___|  _ \ / _ \ / _ \| __| 
        | |_| |___| |_) | (_) | (_) | |_ 
         \___/    |____/ \___/ \___/ \__| 
 ** LOADER **


U-Boot 2009.08 ( 5æœ04 2013 - 15:57:57)Marvell version: 2012_Q4.0
U-Boot Addressing:
       Code:            00600000:006AFFF0
       BSS:             006F9140
       Stack:           0x5fff70
       PageTable:       0x8e0000
       Heap address:    0x900000:0xe00000
Board: RD-88F6710
SoC:   MV6710 A1
CPU:   Marvell PJ4B v7 UP (Rev 1) LE
       CPU @ 1200Mhz, L2 @ 600Mhz
       DDR @ 600Mhz, TClock @ 166Mhz
       DDR 16Bit Width, FastPath Memory Access
PEX 0: Detected No Link.
PEX 1: Detected No Link.
DRAM:  512 MB
       CS 0: base 0x00000000 size 512 MB
       Addresses 14M - 0M are saved for the U-Boot usage.
Failed to initialize SPI flash at 0:0
NAND:  512 MiB
Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
nand_read_bbt: Bad block at 0x0000150a0000
nand_read_bbt: Bad block at 0x00001b4c0000
nand_read_bbt: Bad block at 0x00001b940000
nand_read_bbt: Bad block at 0x00001e8a0000
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
       AUDIO
       TDM
Modules/Interfaces Detected:
       SDIO
       RGMII1 Switch module
       PEX0 (Lane 0)
       PEX1 (Lane 1)
       SATA0 (Lane 2)
       SATA1 (Lane 3)
MMC:   MRVL_MMC: 0
Net:   egiga1 [PRIME]
Hit any key to stop autoboot:  0 

NAND read: device 0 offset 0x500000, size 0x300000
 3145728 bytes read: OK
## Booting kernel from Legacy Image at 02000000 ...
   Image Name:   Linux-3.2.36
   Created:      2013-05-04   9:54:45 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1803200 Bytes =  1.7 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Linux version 3.2.36 (soltek@ubuntu) (gcc version 4.4.5 20100614 (prerelease) (FSF GNU GCC branch-4.4.5. Marvell GCC 201301-317.59f1e272) ) #1 Sat May 4 02:54:39 PDT 2013
[    0.000000] CPU: Marvell PJ4Bv7 Processor [561f5811] revision 1 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] Machine: Marvell Armada-370
[    0.000000] Using UBoot passing parameters structure
[    0.000000] >>>>>>>Tag MAC 02:02:00:43:50:00
[    0.000000] >>>>>>>Tag MAC 02:02:00:43:50:00
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 mtdparts=armada-nand:4m(boot),-(rootfs) root=/dev/nfs rw nfsroot=192.168.1.3:/mnt/ARM_FS/ ip=192.168.1.254:192.168.1.3:10.4.50.254:255.255.255.0:KW40:eth0:none mv_net_config1=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500 video=dovefb:lcd0:$(lcd0_params) clcd.lcd0_enable=$(lcd0_enable) clcd.lcd_panel=$(lcd_panel)
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 512MB = 512MB total
[    0.000000] Memory: 510364k/510364k available, 13924k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xe0800000 - 0xfa800000   ( 416 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc049f000   (4700 kB)
[    0.000000]       .init : 0xc049f000 - 0xc04c7000   ( 160 kB)
[    0.000000]       .data : 0xc04c8000 - 0xc04f4a40   ( 179 kB)
[    0.000000]        .bss : 0xc04f4a64 - 0xc0529124   ( 210 kB)
[    0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] a370_time_init
[    0.000000] sched_clock: 32 bits at 600MHz, resolution 1ns, wraps every 7158ms
[    6.217690] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[    6.307707] pid_max: default: 32768 minimum: 301
[    6.307855] Mount-cache hash table entries: 512
[    6.308157] CPU: Testing write buffer coherency: ok
[    6.308762] devtmpfs: initialized
[    6.312440] NET: Registered protocol family 16
[    6.313990] L0 cache Enabled
[    6.314002] Speculative Prefetch Disabled
[    6.314029] Aurora L2 Cache Enabled
[    6.314063] Support IO coherency.
[    6.314077] Enable DLB and DRAM write coalescing
[    6.325269] 
[    6.325274] CPU Interface
[    6.325279] -------------
[    6.325284] SDRAM_CS0 ....base 00000000, size 512MB 
[    6.325296] SDRAM_CS1 ....disable
[    6.325303] SDRAM_CS2 ....disable
[    6.325309] SDRAM_CS3 ....disable
[    6.325315] DEVICE_CS0 ....base f2000000, size  32MB 
[    6.325328] DEVICE_CS1 ....no such
[    6.325343] DEVICE_CS2 ....no such
[    6.325358] DEVICE_CS3 ....no such
[    6.325374] PEX0_MEM ....base e0000000, size  32MB 
[    6.325384] PEX0_IO ....base f1100000, size   1MB 
[    6.325395] PEX1_MEM ....base e2000000, size  32MB 
[    6.325406] PEX1_IO ....base f1200000, size   1MB 
[    6.325417] INTER_REGS ....base d0000000, size   1MB 
[    6.325427] DMA_UART ....no such
[    6.325443] SPI_CS0 ....base f0000000, size  16MB 
[    6.325454] SPI_CS1 ....no such
[    6.325469] SPI_CS2 ....no such
[    6.325485] SPI_CS3 ....no such
[    6.325500] SPI_CS4 ....no such
[    6.325515] SPI_CS5 ....no such
[    6.325530] SPI_CS6 ....no such
[    6.325545] SPI_CS7 ....no such
[    6.325560] BOOT_ROM_CS ....no such
[    6.325576] DEV_BOOTCS ....base f5000000, size  16MB 
[    6.325588] PMU_SCRATCHPAD ....no such
[    6.325604] CRYPT0_ENG ....base c8010000, size  64KB 
[    6.325616] 
[    6.325619]   Marvell Armada370 Board-- RD-88F6710  Soc: MV6710 A1 LE
[    6.325632]   LSP version: linux-3.2.y-2013_Q1.0p2
[    6.325638] 
[    6.325640] 
[    6.325648]  Detected Tclk 166666667, SysClk 600000000, FabricClk 600000000
[    6.328943] Marvell USB EHCI Host controller #0: d004f800
[    6.329292] Marvell USB EHCI Host controller #1: d004fa00
[    6.329762] PCI: bus0: Fast back to back transfers enabled
[    6.329935] PCI: bus1: Fast back to back transfers enabled
[    6.339597] bio: create slab <bio-0> at 0
[    6.340309] SCSI subsystem initialized
[    6.341049] usbcore: registered new interface driver usbfs
[    6.341255] usbcore: registered new interface driver hub
[    6.341384] usbcore: registered new device driver usb
[    6.342262] Switching to clocksource armada370_clocksource
[    6.343892] NET: Registered protocol family 2
[    6.343991] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    6.344165] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    6.344332] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[    6.344432] TCP: Hash tables configured (established 16384 bind 16384)
[    6.344442] TCP reno registered
[    6.344452] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    6.344467] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    6.344657] NET: Registered protocol family 1
[    6.344834] RPC: Registered named UNIX socket transport module.
[    6.344844] RPC: Registered udp transport module.
[    6.344850] RPC: Registered tcp transport module.
[    6.344857] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    6.345056] cesadev_init(c04a6e84)
[    6.345654] mvCesaInit: channels=1, session=640, queue=64
[    6.350243] Armada XP hwmon thermal sensor initialized.
[    6.350337] Initializing Armada-XP CPU power management  (WFI)
[    6.359004] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    6.359505] JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
[    6.359940] msgmni has been set to 996
[    6.360385] io scheduler noop registered
[    6.360394] io scheduler deadline registered
[    6.360427] io scheduler cfq registered (default)
[    6.360482] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[    6.360520] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
[    6.372364] mv_xor mv_xor.0: Marvell XOR: ( xor )
[    6.392365] mv_xor mv_xor.1: Marvell XOR: ( xor )
[    6.412314] mv_xor mv_xor.2: Marvell XOR: ( cpy )
[    6.432314] mv_xor mv_xor.3: Marvell XOR: ( fill cpy )
[    6.437271] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    6.438014] serial8250.0: ttyS0 at MMIO 0xd0012000 (irq = 41) is a 16550A
[    7.035240] console [ttyS0] enabled
[    7.042029] brd: module loaded
[    7.048350] loop: module loaded
[    7.052187] sata_mv sata_mv.0: slots 32 ports 2
[    7.058349] scsi0 : sata_mv
[    7.061473] scsi1 : sata_mv
[    7.064562] ata1: SATA max UDMA/133 irq 55
[    7.068632] ata2: SATA max UDMA/133 irq 55
[    7.151917] mv_eth_probe: port_mask=0x3, cpu_mask=0x1 
[    7.157106] 0 - Base 0x00000000 , Size = 0x00000001.
[    7.162036] 4 - Base 0xf2000000 , Size = 0x00000001.
[    7.166971] 8 - Base 0xe0000000 , Size = 0x00000001.
[    7.171899] 9 - Base 0xf1100000 , Size = 0x00000001.
[    7.176833] 10 - Base 0xe2000000 , Size = 0x00000001.
[    7.181848] 11 - Base 0xf1200000 , Size = 0x00000001.
[    7.186867] 12 - Base 0xd0000000 , Size = 0x00000001.
[    7.191882] 14 - Base 0xf0000000 , Size = 0x00000001.
[    7.196901] 23 - Base 0xf5000000 , Size = 0x00000001.
[    7.201915] 25 - Base 0xc8010000 , Size = 0x00000001.
[    7.206950]   o 2 Giga ports supported
[    7.210671]   o SKB recycle supported (Enabled)
[    7.215172]   o NETA acceleration mode 1
[    7.219066]   o RX Queue support: 8 Queues * 128 Descriptors
[    7.224690]   o TX Queue support: 8 Queues * 532 Descriptors
[    7.230307]   o GSO supported
[    7.233255]   o GRO supported
[    7.236199]   o Receive checksum offload supported
[    7.240953]   o Transmit checksum offload supported
[    7.245799]   o Driver ERROR statistics enabled
[    7.250295]   o Switch support enabled
[    7.254019] 
[    7.255639]   o Loading Switch QuarterDeck driver
[    7.263723]     o Device ID     : 0x171
[    7.267530]     o No. of Ports  : 7
[    7.270991]     o CPU Port      : 5
[    7.275844]     o Setting Switch Port #5 connected to GMAC port for 1000 Full with FC
[    7.284577]     o Disable disconnected Switch Port #6 and force link down
[    7.291695]   o Loading network interface(s)
[    7.295941] 
[    7.295944]   o Warning: GbE port 0 is not connected to PHY/RGMII/Switch, skip initialization
[    7.295951] 
[    7.307366] 
[    7.308846]   o Port 1 is connected to Linux netdevice
[    7.314041]       o Using UBoot netconfig string for port 1
[    7.319576]         net_config_str[1]: 1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500
[    7.326854]       o MTU set to 1500.
[    7.356623] Port 4: Link-up, Full-duplex, Speed-1000Mbps.
[    7.364368]  giga p=1: mtu=1500, mac=d0037e58
[    7.372588]     o eth0, ifindex = 2, GbE port = 1. Interface ports: 0 1 2 3 4 
[    7.394930] 
[    7.396686] PPP generic driver version 2.4.2
[    7.401201] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.407747] ehci_marvell ehci_marvell.0: Marvell Orion EHCI
[    7.413337] ehci_marvell ehci_marvell.0: new USB bus registered, assigned bus number 1
[    7.442300] ehci_marvell ehci_marvell.0: irq 45, io base 0xfbb50100
[    7.462288] ehci_marvell ehci_marvell.0: USB 2.0 started, EHCI 1.00
[    7.469118] hub 1-0:1.0: USB hub found
[    7.472877] hub 1-0:1.0: 1 port detected
[    7.477112] ehci_marvell ehci_marvell.1: Marvell Orion EHCI
[    7.482683] ehci_marvell ehci_marvell.1: new USB bus registered, assigned bus number 2
[    7.492313] ata1: SATA link down (SStatus 0 SControl F300)
[    7.512317] ehci_marvell ehci_marvell.1: irq 46, io base 0xfbb51100
[    7.532293] ehci_marvell ehci_marvell.1: USB 2.0 started, EHCI 1.00
[    7.539099] hub 2-0:1.0: USB hub found
[    7.542852] hub 2-0:1.0: 1 port detected
[    7.547272] Initializing USB Mass Storage driver...
[    7.552273] usbcore: registered new interface driver usb-storage
[    7.558252] USB Mass Storage support registered.
[    7.842300] ata2: SATA link down (SStatus 0 SControl F300)
[    8.572291] rtc-mv rtc-mv: internal RTC not ticking
[    8.577346] md: linear personality registered for level -1
[    8.582806] md: raid0 personality registered for level 0
[    8.588080] md: raid1 personality registered for level 1
[    8.593359] md: raid10 personality registered for level 10
[    8.598916] cpuidle: using governor ladder
[    8.603165] cpuidle: using governor menu
[    8.608355] mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
[    8.616536] TCP cubic registered
[    8.620391] NET: Registered protocol family 10
[    8.625439] IPv6 over IPv4 tunneling driver
[    8.630052] NET: Registered protocol family 17
[    8.634560] 8021q: 802.1Q VLAN Support v1.8
[    8.638727] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6
[    8.646355] ThumbEE CPU extension supported.
[    8.651711] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    8.660198] Port 0: Link-down
[    8.665197] Port 1: Link-down
[    8.670200] Port 2: Link-down
[    8.675205] Port 3: Link-down
[    8.680420] eth0: link up
[    8.683031] Port 4: Link-up, Full-duplex, Speed-1000Mbps.
[    8.690575] pool #1: pkt_size=1536, buf_size=1632 - 2048 of 2048 buffers added
[    8.699784] eth0: started (on switch)
[    8.782475] IP-Config: Gateway not on directly connected network.
[    8.788732] md: Waiting for all devices to be available before autodetect
[    8.795499] md: If you don't use raid, use raid=noautodetect
[    8.801808] md: Autodetecting RAID arrays.
[    8.805898] md: Scanned 0 and added 0 devices.
[    8.810308] md: autorun ...
[    8.813090] md: ... autorun DONE.

(Last edited by linuxpro on 17 Jun 2014, 06:11)

Post #405
jklap
17 Jun 2014, 13:14
jalyst wrote:

Did anyone else get unsubscribed from this thread after it was moved to this sub-forum?
I only just noticed, luckily...

Something is funky-- I'm still sub'ed but not receiving any emails. Just noticed a whole new page wink

Post #406
jalyst
17 Jun 2014, 13:21

^Thank for confirming, thought I might've been going crazy... O_o


jalyst wrote:

Did anyone else get unsubscribed from this thread after it was moved to this sub-forum?
I only just noticed, luckily...

So nyt, it's now over 2wks???
"Also, you should see some good news in 2-3 weeks, so sit tight."

Post:
https://forum.openwrt.org/viewtopic.php … 14#p235214


@nyt

Just a *BUMP* in case this was missed due to the forum funkiness that's been occurring.


Cheers.

(Last edited by jalyst on 17 Jun 2014, 14:01)

Post #407
nyt
17 Jun 2014, 20:26
jalyst wrote:

^Thank for confirming, thought I might've been going crazy... O_o


jalyst wrote:

Did anyone else get unsubscribed from this thread after it was moved to this sub-forum?
I only just noticed, luckily...

So nyt, it's now over 2wks???
"Also, you should see some good news in 2-3 weeks, so sit tight."

Post:
https://forum.openwrt.org/viewtopic.php … 14#p235214


@nyt

Just a *BUMP* in case this was missed due to the forum funkiness that's been occurring.


Cheers.

I'm not Belkin, and it hasn't happened yet.  I'll be sure to post when it does.

Post #408
gufus
17 Jun 2014, 21:37
nyt wrote:
jalyst wrote:

^Thank for confirming, thought I might've been going crazy... O_o


jalyst wrote:

Did anyone else get unsubscribed from this thread after it was moved to this sub-forum?
I only just noticed, luckily...

So nyt, it's now over 2wks???
"Also, you should see some good news in 2-3 weeks, so sit tight."

Post:
https://forum.openwrt.org/viewtopic.php … 14#p235214


@nyt

Just a *BUMP* in case this was missed due to the forum funkiness that's been occurring.


Cheers.

I'm not Belkin, and it hasn't happened yet.  I'll be sure to post when it does.

smile

ttul....

Post #409
dfarning
17 Jun 2014, 22:37

In more related good news...

John Crispin as done a series of commits related to WRT1900AC. ( https://dev.openwrt.org/timeline )

Post #410
dstruktNine
17 Jun 2014, 23:10

Hi guys! New user here! I just got my 1900AC today and just noticed that OpenWRT isn't fully implemented yet? sad

http://wiki.openwrt.org/toh/linksys/wrt1900ac

I saw someone above post a link to a Mamba build, but I don't know what I'm suppose to download and install.

https://github.com/jimmychungbelkin/Mamba

Can one of you fine people tell me how to get this installed? I'm really excited and anxious big_smile

I found this tutorial, but I am unsure which method to use.

http://wiki.openwrt.org/doc/howto/generic.flashing

Thanks! smile

Post #411
Chadster766
17 Jun 2014, 23:16
dstruktNine wrote:

Hi guys! New user here! I just got my 1900AC today and just noticed that OpenWRT isn't fully implemented yet? sad

http://wiki.openwrt.org/toh/linksys/wrt1900ac

I saw someone above post a link to a Mamba build, but I don't know what I'm suppose to download and install.

https://github.com/jimmychungbelkin/Mamba

Can one of you fine people tell me how to get this installed? I'm really excited and anxious big_smile

I found this tutorial, but I am unsure which method to use.

http://wiki.openwrt.org/doc/howto/generic.flashing

Thanks! smile

There's lots of options smile

Go to link below:

https://github.com/wrt1900ac/opensource

You can choose either Attitude Adjustment (My fav) or Barrier Breaker (Bleeding Edge)

Upload the firmware using the WRT1900AC Stock UI firmware upload feature.

I recommend downloading a copy of the Linksys stock firmware for easy access just in case you need it.

Post #412
gufus
17 Jun 2014, 23:36
dstruktNine wrote:

Hi guys! New user here! I just got my 1900AC today and just noticed that OpenWRT isn't fully implemented yet? sad

http://wiki.openwrt.org/toh/linksys/wrt1900ac

I saw someone above post a link to a Mamba build, but I don't know what I'm suppose to download and install.

https://github.com/jimmychungbelkin/Mamba

Can one of you fine people tell me how to get this installed? I'm really excited and anxious big_smile

I found this tutorial, but I am unsure which method to use.

http://wiki.openwrt.org/doc/howto/generic.flashing

Thanks! smile

BTY

Read this! IMPORTANT
https://forum.openwrt.org/viewtopic.php … 64#p235564

https://forum.openwrt.org/viewtopic.php … 68#p235268

(Last edited by gufus on 18 Jun 2014, 00:29)

Post #413
dstruktNine
18 Jun 2014, 00:47

Thanks everyone. So I've flashed with AA and wireless isn't working well. I can't find anything in the wiki that shows the GUI that this firmware has. I went to wifi and it says mode is unknown for both radios.

What do I select under Network? LAN, Wan, Wan6? I've different ones and haven't had any luck. None of my wireless devices are connecting to the router. I've named it the same SSID and pw as my old router.

Another thing is that certain websites aren't loading and the overall speed is sluggish.

EDIT: I changed the DHCP to auto and my router crashed. Couldn't connect after multiple reboots and hard reboots. It was pretty much bricked. Followed the generic debrick wiki and couldn't connect to it via Telnet. Tried this post below:

https://forum.openwrt.org/viewtopic.php … 21#p233921

And nothing. So I went and exchanged the router for a new one a little while ago and I have stock firmware running :\

So, the steps I took to install openwrt are as follows:

* Downloaded openwrt-armadaxp--jffs2-128k.img
* Logged into the stock webgui and installed the firmware
* Waited for the router to reboot
* Tried configuring wireless radios

After that, nothing. The radios were broadcasting, but I could not connect to them. It said something like Generic Wireless device under the Wifi tab.

Where it would say what channel the radio was on, it was a ?, even when I tried to manually set the wireless channel.

Overall, pretty buggy. I wonder if the firmware I downloaded was corrupted in some way since I downloaded it on one computer and then transferred it via flash drive to my laptop so I could flash it.

(Last edited by dstruktNine on 18 Jun 2014, 02:56)

Post #414
jalyst
18 Jun 2014, 05:40
nyt wrote:
jalyst wrote:

So nyt, it's now over 2wks???
"Also, you should see some good news in 2-3 weeks, so sit tight."

Post:
https://forum.openwrt.org/viewtopic.php … 14#p235214

I'm not Belkin, and it hasn't happened yet.  I'll be sure to post when it does.

I appreciate that, but you seemed confident that something substantial would happen in 2-3wks*, not so confident now?

dfarning wrote:

In more related good news...

John Crispin as done a series of commits related to WRT1900AC. ( https://dev.openwrt.org/timeline )

Last I checked the mail-list, Belkin's submissions were almost 100% naks...
Admittedly I haven't checked the latest big dump (usually ~1/mth IIRC) they did a few days back IIRC.
Hopefully the success rate has improved dramatically, for their sake...


*If this project is to get more traction & not be dead (comparatively speaking), we know what that substantial thing MUST be

(Last edited by jalyst on 18 Jun 2014, 05:58)

Post #415
Drakia
18 Jun 2014, 16:00
dstruktNine wrote:

Thanks everyone. So I've flashed with AA and wireless isn't working well. I can't find anything in the wiki that shows the GUI that this firmware has. I went to wifi and it says mode is unknown for both radios.

What do I select under Network? LAN, Wan, Wan6? I've different ones and haven't had any luck. None of my wireless devices are connecting to the router. I've named it the same SSID and pw as my old router.

Another thing is that certain websites aren't loading and the overall speed is sluggish.

EDIT: I changed the DHCP to auto and my router crashed. Couldn't connect after multiple reboots and hard reboots. It was pretty much bricked. Followed the generic debrick wiki and couldn't connect to it via Telnet. Tried this post below:

https://forum.openwrt.org/viewtopic.php … 21#p233921

And nothing. So I went and exchanged the router for a new one a little while ago and I have stock firmware running :\

So, the steps I took to install openwrt are as follows:

* Downloaded openwrt-armadaxp--jffs2-128k.img
* Logged into the stock webgui and installed the firmware
* Waited for the router to reboot
* Tried configuring wireless radios

After that, nothing. The radios were broadcasting, but I could not connect to them. It said something like Generic Wireless device under the Wifi tab.

Where it would say what channel the radio was on, it was a ?, even when I tried to manually set the wireless channel.

Overall, pretty buggy. I wonder if the firmware I downloaded was corrupted in some way since I downloaded it on one computer and then transferred it via flash drive to my laptop so I could flash it.

OpenWRT on the 1900AC is pretty much alpha quality at this point. The wireless  information being a bunch of ? is one of the current bugs. There are also WiFi drops and making the router inaccessible via the web ui is extremely easy to do.

I would recommend sticking with the stock firmware unless you are willing to crack open the case and use a serial adapter to reflash the firmware when it gets messed up.

Post #416
dstruktNine
18 Jun 2014, 18:06

Yeah, I saw a post about needing a USB to TTL cable. I'm a bit disappointed that OpenWrt isn't fully implemented; the reason I bought this router was for OpenWrt. I guess I'll wait til it becomes more stable.

Post #417
Drakia
19 Jun 2014, 03:22
dstruktNine wrote:

Yeah, I saw a post about needing a USB to TTL cable. I'm a bit disappointed that OpenWrt isn't fully implemented; the reason I bought this router was for OpenWrt. I guess I'll wait til it becomes more stable.

Sadly Belkin was claiming OpenWRT support long before they actually got in contact with the developers to get things ready. Currently they've submitted patches multiple times that don't meet the requirements to be merged into trunk.

Apparently the developers have been given the hardware they need to work on getting things up to snuff, but there's no ETA on when there will be a fully compatible stable build sad

Post #418
dstruktNine
19 Jun 2014, 03:23

Guess I'll just try to hold off on installing it until a stable release is available sad

Post #419
AdamK
20 Jun 2014, 21:55

Amazing.  I don't own one of these routers yet but I have to say that it is disappointing that Linksys touted full OpenWRT support AND RELEASED this router to market, before meeting all the OpenWRT developer needs.

A very poor effort on Linksys' part.

Post #420
gufus
20 Jun 2014, 23:46
AdamK wrote:

A very poor effort on Linksys' part.

Yep.

I'm very optimistic it will get resolved, there's a lot on the line.

Post #421
dfarning
21 Jun 2014, 03:37

In my experience the problem is a lack of understanding between marketing, legal and engineering about what should happen. Engineering departments are usually pretty level headed. Marketing departments say whatevery they need to say to move product. Legal departments tend to slap anyone's hands who come too near their "proprietary information.

In this case, the engineering department seems to be operating in good faith. Slower than we might like but, still in good faith. The Marketing department got ahead of themselves and claimed OpenWrt compatibility prematurely (oops). The problem seems to be legal. They are not approving the release of information or unable to work with 3rd parties such as Marvell to release the necessary information.

An interesting data point is that the official public Belkin tree seems to be maintain by Veriksystem.... The is a pretty good chance that Belkin developers have sign enough non-disclosure agreements during their careers that Belkin must outsource the the openwrt on wrt1900AC work to a independent contractor.

Post #422
xpusostomos
21 Jun 2014, 05:15
dfarning wrote:

In my experience the problem is a lack of understanding between marketing, legal and engineering about what should happen. Engineering departments are usually pretty level headed. Marketing departments say whatevery they need to say to move product. Legal departments tend to slap anyone's hands who come too near their "proprietary information.

In this case, the engineering department seems to be operating in good faith. Slower than we might like but, still in good faith. The Marketing department got ahead of themselves and claimed OpenWrt compatibility prematurely (oops). The problem seems to be legal. They are not approving the release of information or unable to work with 3rd parties such as Marvell to release the necessary information.

An interesting data point is that the official public Belkin tree seems to be maintain by Veriksystem.... The is a pretty good chance that Belkin developers have sign enough non-disclosure agreements during their careers that Belkin must outsource the the openwrt on wrt1900AC work to a independent contractor.

Possibly, but it's crazy to advertise your product as open source compatible without sign off from legal and Marvell's legal.

Post #423
linuxpro
21 Jun 2014, 16:15

upgrade...

Marvell Armada370  system boot log.

BootROM 1.08
Booting from NAND flash
High speed PHY - Version: 2.1.2 (COM-PHY-V20) 
Update PEX Device ID 0x67100
High speed PHY - Ended Successfully
                                   DDR3 Training Sequence - Ver 4.5.0 
DDR3 Training Sequence - Ended Successfully 
Status = MV_OK
BootROM: Image checksum verification PASSED

 __   __                      _ _
|  \/  | __ _ _ ____   _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| |  | | (_| | |   \ V /  __/ | |
|_|  |_|\__,_|_|    \_/ \___|_|_|
         _   _     ____              _
        | | | |   | __ )  ___   ___ | |_ 
        | | | |___|  _ \ / _ \ / _ \| __| 
        | |_| |___| |_) | (_) | (_) | |_ 
         \___/    |____/ \___/ \___/ \__| 
 ** LOADER **


U-Boot 2011.12 (Jun 15 2014 - 11:06:44) RTNAS V3 2013_Q2.0

Board: RD-88F6710
SoC:   MV6710 A1
CPU:   Marvell PJ4B v7 UP (Rev 1) LE
       CPU    @ 1200 [MHz]
       L2     @ 600 [MHz]
       TClock @ 200 [MHz]
       DDR    @ 600 [MHz]
       DDR 16Bit Width, FastPath Memory Access
DRAM:  512 MiB

Map:   Code:            0x1ff0f000:0x1ffa11f4
       BSS:             0x1ffef340
       Stack:           0x1fa0eef8
       Heap:            0x1fa0f000:0x1ff0f000

NAND:  4096 MiB
MMC:   MRVL_MMC: 0
Bad block table found at page 1048320, version 0x01
Bad block table found at page 1048064, version 0x01
nand_read_bbt: Bad block at 0x000005a00000
nand_read_bbt: Bad block at 0x000005b00000
nand_read_bbt: Bad block at 0x000010300000
nand_read_bbt: Bad block at 0x0000f4500000
nand_read_bbt: Bad block at 0x0000f6500000
PEX 0.0(0): Detected No Link.
PEX 1: Root Complex Interface, Detected Link X1, GEN 1.1
start OpenWrtLinux..........
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Modules/Interfaces Detected:
       RGMII1 Switch module
       PEX0 (Lane 0)
       PEX1 (Lane 1)
       SATA0 (Lane 2)
       SATA1 (Lane 3)
Not Marvell PHY id1 ffff id2 ffff
Net:   egiga1 [PRIME]
Press Ctrl+C to abort autoboot in 3 second

NAND read: device 0 offset 0x1800000, size 0x400000
 4194304 bytes read: OK
## Booting kernel from Legacy Image at 02000000 ...
   Image Name:   Linux-3.2.40
   Created:      2014-06-08   2:37:31 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2103136 Bytes = 2 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Linux version 3.2.40 (vincent@RTNAS) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #2 Sun Jun 8 10:37:27 CST 2014
[    0.000000] CPU: Marvell PJ4Bv7 Processor [561f5811] revision 1 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] Machine: Marvell Armada-370
[    0.000000] Using UBoot passing parameters structure
[    0.000000] >>>>>>>Tag MAC 00:02:02:43:50:00
[    0.000000] >>>>>>>Tag MAC 00:00:02:43:50:00
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 ubi.mtd=5 root=ubi0:rootfs ro rootfstype=ubifs
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 512MB = 512MB total
[    0.000000] Memory: 509760k/509760k available, 14528k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xe0800000 - 0xfa800000   ( 416 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc05314e4   (5286 kB)
[    0.000000]       .init : 0xc0532000 - 0xc055a000   ( 160 kB)
[    0.000000]       .data : 0xc055a000 - 0xc058c360   ( 201 kB)
[    0.000000]        .bss : 0xc058c384 - 0xc05c158c   ( 213 kB)
[    0.000000] NR_IRQS:256
[    0.000000] a370_time_init
[    0.000000] sched_clock: 32 bits at 600MHz, resolution 1ns, wraps every 7158ms
[    7.118117] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[    7.158099] pid_max: default: 32768 minimum: 301
[    7.158209] Mount-cache hash table entries: 512
[    7.158449] CPU: Testing write buffer coherency: ok
[    7.158953] devtmpfs: initialized
[    7.161549] xor: measuring software checksum speed
[    7.208070]    arm4regs  :  1149.200 MB/sec
[    7.258068]    8regs     :   816.800 MB/sec
[    7.308066]    32regs    :  1150.000 MB/sec
[    7.308074] xor: using function: 32regs (1150.000 MB/sec)
[    7.308197] NET: Registered protocol family 16
[    7.309484] L0 cache Enabled
[    7.309494] Speculative Prefetch Disabled
[    7.309517] Aurora L2 Cache Enabled
[    7.309549] Support IO coherency.
[    7.309562] Enable DLB and DRAM write coalescing
[    7.320742] 
[    7.320747] CPU Interface
[    7.320751] -------------
[    7.320755] SDRAM_CS0 ....base 00000000, size 512MB 
[    7.320767] SDRAM_CS1 ....disable
[    7.320773] SDRAM_CS2 ....disable
[    7.320778] SDRAM_CS3 ....disable
[    7.320784] DEVICE_CS0 ....base f2000000, size  32MB 
[    7.320795] DEVICE_CS1 ....no such
[    7.320810] DEVICE_CS2 ....no such
[    7.320825] DEVICE_CS3 ....no such
[    7.320839] PEX0_MEM ....base e0000000, size  32MB 
[    7.320849] PEX0_IO ....base f1100000, size   1MB 
[    7.320858] PEX1_MEM ....base e2000000, size  32MB 
[    7.320868] PEX1_IO ....base f1200000, size   1MB 
[    7.320879] INTER_REGS ....base f1000000, size   1MB 
[    7.320888] DMA_UART ....no such
[    7.320902] SPI_CS0 ....base f0000000, size  16MB 
[    7.320913] SPI_CS1 ....no such
[    7.320927] SPI_CS2 ....no such
[    7.320942] SPI_CS3 ....no such
[    7.320956] SPI_CS4 ....no such
[    7.320970] SPI_CS5 ....no such
[    7.320984] SPI_CS6 ....no such
[    7.320999] SPI_CS7 ....no such
[    7.321013] BOOT_ROM_CS ....no such
[    7.321027] DEV_BOOTCS ....base f5000000, size  16MB 
[    7.321039] PMU_SCRATCHPAD ....no such
[    7.321053] CRYPT0_ENG ....base c8010000, size  64KB 
[    7.321065] PNC_BM ....no such
[    7.321079] 
[    7.321082]   Marvell Armada370 Board-- RD-88F6710  Soc: MV6710 A1 LE
[    7.321094]   LSP version: linux-3.2.y-2013_Q2.0p2
[    7.321099] 
[    7.321101] 
[    7.321109]  Detected Tclk 200000000, SysClk 600000000, FabricClk 600000000
[    7.324124] Marvell USB EHCI Host controller #0: d0047000
[    7.324465] Marvell USB EHCI Host controller #1: d005ae00
[    7.324917] PCI: bus0: Fast back to back transfers enabled
[    7.325322] PCI: bus1: Fast back to back transfers disabled
[    7.325500] pci 0000:01:00.0: BAR 0: assigned [mem 0xe2000000-0xe201ffff 64bit]
[    7.325520] pci 0000:01:00.0: BAR 0: set to [mem 0xe2000000-0xe201ffff 64bit] (PCI address [0xe2000000-0xe201ffff])
[    7.325534] pci 0000:01:00.0: BAR 6: assigned [mem 0xe2020000-0xe202ffff pref]
[    7.334790] bio: create slab <bio-0> at 0
[    7.498413] raid6: int32x1    136 MB/s
[    7.668164] raid6: int32x2    210 MB/s
[    7.838317] raid6: int32x4    203 MB/s
[    8.008109] raid6: int32x8    237 MB/s
[    8.008115] raid6: using algorithm int32x8 (237 MB/s)
[    8.008436] vgaarb: loaded
[    8.008848] SCSI subsystem initialized
[    8.009497] usbcore: registered new interface driver usbfs
[    8.009670] usbcore: registered new interface driver hub
[    8.009778] usbcore: registered new device driver usb
[    8.010615] Switching to clocksource armada370_clocksource
[    8.012160] NET: Registered protocol family 2
[    8.012271] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    8.012494] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    8.012685] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[    8.012797] TCP: Hash tables configured (established 16384 bind 16384)
[    8.012805] TCP reno registered
[    8.012815] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    8.012831] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    8.012997] NET: Registered protocol family 1
[    8.013172] RPC: Registered named UNIX socket transport module.
[    8.013181] RPC: Registered udp transport module.
[    8.013187] RPC: Registered tcp transport module.
[    8.013193] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    8.013373] cesadev_init(c05391c0)
[    8.013914] mvCesaInit: channels=1, session=640, queue=64
[    8.019427] Armada XP hwmon thermal sensor initialized.
[    8.019509] Armada370 Power Managament Suspend Operations Initialized
[    8.019518] Initializing Armada-XP CPU power management  (WFI)
[    8.020746] NTFS driver 2.1.30 [Flags: R/W].
[    8.021017] msgmni has been set to 995
[    8.021480] async_tx: api initialized (async)
[    8.021614] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    8.021625] io scheduler noop registered
[    8.021631] io scheduler deadline registered (default)
[    8.021669] io scheduler cfq registered
[    8.021702] Initializing ths8200_init
[    8.021794] Initializing dove_adi9889_init
[    8.021897] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[    8.021932] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
[    8.040655] mv_xor mv_xor.0: Marvell XOR: ( xor )
[    8.060665] mv_xor mv_xor.1: Marvell XOR: ( xor )
[    8.080662] mv_xor mv_xor.2: Marvell XOR: ( cpy )
[    8.100662] mv_xor mv_xor.3: Marvell XOR: ( fill cpy )
[    8.104924] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    8.105552] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 41) is a 16550A
[    8.759760] console [ttyS0] enabled
[    8.769011] brd: module loaded
[    8.775069] loop: module loaded
[    8.778219] Loading iSCSI transport class v2.0-870.
[    8.784247] sata_mv sata_mv.0: slots 32 ports 2
[    8.790327] scsi0 : sata_mv
[    8.793521] scsi1 : sata_mv
[    8.796565] ata1: SATA max UDMA/133 irq 55
[    8.800687] ata2: SATA max UDMA/133 irq 55
[    8.805634] armada-nand armada-nand.0: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC
[    8.818633] NAND device: Manufacturer ID: 0x2c, Chip ID: 0x68 (Micron NAND 4GiB 3,3V 8-bit)
[    8.827540] Bad block table found at page 1048320, version 0x01
[    8.834136] Bad block table found at page 1048064, version 0x01
[    8.840404] nand_read_bbt: bad block at 0x000005a00000
[    8.845558] nand_read_bbt: bad block at 0x000005b00000
[    8.850711] nand_read_bbt: bad block at 0x000010300000
[    8.855890] nand_read_bbt: bad block at 0x0000f4500000
[    8.861042] nand_read_bbt: bad block at 0x0000f6500000
[    8.866407] Creating 8 MTD partitions on "armada-nand"(4194304 Kbytes):
[    8.873051] 0x000000000000-0x000000400000 : "UBoot"
[    8.878737] 0x000000400000-0x000000800000 : "UBoot_env"
[    8.884715] 0x000000800000-0x000000c00000 : "vendor"
[    8.890023] MAC 0 Address : 00:11:32:21:46:89
[    8.894405] MAC 1 Address : 00:11:32:21:46:8a
[    8.898775] serial number='1360LAN001179'
[    8.903401] 0x000000c00000-0x000001800000 : "unused"
[    8.909270] 0x000001800000-0x000001c00000 : "kernel"
[    8.915000] 0x000001c00000-0x000009c00000 : "rootfs"
[    8.920716] mtd: partition "rootfs" set to be root filesystem
[    8.926480] 0x000009c00000-0x00003fc00000 : "rootfs_data"
[    8.932660] 0x000001800000-0x000009c00000 : "firmware"
[    8.938630] mv_eth_probe: port_mask=0x3, cpu_mask=0x1 
[    8.943889]   o 2 Giga ports supported
[    8.947645]   o SKB recycle supported (Enabled)
[    8.952188]   o NETA acceleration mode 1
[    8.956118]   o RX Queue support: 8 Queues * 512 Descriptors
[    8.961792]   o TX Queue support: 8 Queues * 512 Descriptors
[    8.967460]   o GSO supported
[    8.970430]   o GRO supported
[    8.973405]   o Receive checksum offload supported
[    8.978203]   o Transmit checksum offload supported
[    8.983091]   o Driver ERROR statistics enabled
[    8.987628]   o Switch support enabled
[    8.991386] 
[    8.993068]   o Loading Switch QuarterDeck driver
[    9.000889]     o Device ID     : 0x171
[    9.004731]     o No. of Ports  : 7
[    9.008223]     o CPU Port      : 5
[    9.012945]     o Setting Switch Port #5 connected to GMAC port for 1000 Full with FC
[    9.021637]     o Disable disconnected Switch Port #6 and force link down
[    9.028773]   o Loading network interface(s)
[    9.033059] 
[    9.033061]   o Warning: GbE port 0 is not connected to PHY/RGMII/Switch, skip initialization
[    9.033067] 
[    9.044589] 
[    9.046081]   o Port 1 is connected to Linux netdevice
[    9.051307]       o Using default netconfig string from Kconfig for port 1
[    9.058195]         net_config_str[1]: 2,(00:50:43:11:11:12,0:1:2:3)(00:50:43:22:22:22,4),mtu=1500
[    9.067191]       o MTU set to 1500.
[    9.090746] Port 0: Link-up, Full-duplex, Speed-1000Mbps.
[    9.103463]  giga p=1: mtu=1500, mac=d0029ef4
[    9.111654]     o eth0, ifindex = 2, GbE port = 1. Interface ports: 0 1 2 3 
[    9.130128]     o eth1, ifindex = 3, GbE port = 1. Interface ports: 4 
[    9.140953] Cycles: Counter=0, opIdx=17, overhead=13, max=0xffffffff
[    9.147321] Instr: Counter=1, opIdx=8, overhead=13, max=0xffffffff
[    9.153520] IcMiss: Counter=2, opIdx=96, overhead=0, max=0xffffffff
[    9.159799] DcRdMiss: Counter=3, opIdx=65, overhead=0, max=0xffffffff
[    9.166260] DcWrMiss: Counter=4, opIdx=67, overhead=0, max=0xffffffff
[    9.172718] dTlbMiss: Counter=5, opIdx=113, overhead=0, max=0xffffffff
[    9.179260] 
[    9.181660] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
[    9.188375]  Hooking IMQ before NAT on PREROUTING.
[    9.193191]  Hooking IMQ after NAT on POSTROUTING.
[    9.198002] PPP generic driver version 2.4.2
[    9.202545] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    9.209128] ehci_marvell ehci_marvell.0: Marvell Orion EHCI
[    9.214775] ehci_marvell ehci_marvell.0: new USB bus registered, assigned bus number 1
[    9.222806] ata1: SATA link down (SStatus 0 SControl F300)
[    9.250650] ehci_marvell ehci_marvell.0: irq 45, io base 0xfbb50100
[    9.270637] ehci_marvell ehci_marvell.0: USB 2.0 started, EHCI 1.00
[    9.277470] hub 1-0:1.0: USB hub found
[    9.281253] hub 1-0:1.0: 1 port detected
[    9.285477] ehci_marvell ehci_marvell.1: Marvell Orion EHCI
[    9.291093] ehci_marvell ehci_marvell.1: new USB bus registered, assigned bus number 2
[    9.320648] ehci_marvell ehci_marvell.1: irq 46, io base 0xfbb51100
[    9.340636] ehci_marvell ehci_marvell.1: USB 2.0 started, EHCI 1.00
[    9.347407] hub 2-0:1.0: USB hub found
[    9.351186] hub 2-0:1.0: 1 port detected
[    9.355577] uhci_hcd: USB Universal Host Controller Interface driver
[    9.362225] usbcore: registered new interface driver usblp
[    9.367722] Initializing USB Mass Storage driver...
[    9.372750] usbcore: registered new interface driver usb-storage
[    9.378769] USB Mass Storage support registered.
[    9.383542] usbcore: registered new interface driver ums-usbat
[    9.570648] ata2: SATA link down (SStatus 0 SControl F300)
[   10.390634] rtc-mv rtc-mv: internal RTC not ticking
[   10.395700] i2c /dev entries driver
[   10.400546] md: linear personality registered for level -1
[   10.406059] md: raid0 personality registered for level 0
[   10.411386] md: raid1 personality registered for level 1
[   10.416708] md: raid10 personality registered for level 10
[   10.422208] md: raid6 personality registered for level 6
[   10.427529] md: raid5 personality registered for level 5
[   10.432854] md: raid4 personality registered for level 4
[   10.438175] md: multipath personality registered for level -4
[   10.444023] device-mapper: uevent: version 1.0.3
[   10.448866] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[   10.457433] cpuidle: using governor ladder
[   10.461875] usbcore: registered new interface driver ushc
[   10.467335] GACT probability on
[   10.470484] Mirror/redirect action on
[   10.474533] netem: version 1.3
[   10.477600] u32 classifier
[   10.480309]     Performance counters on
[   10.484165]     input device check on
[   10.487832]     Actions configured
[   10.491247] Netfilter messages via NETLINK v0.30.
[   10.495974] nf_conntrack version 0.5.0 (7965 buckets, 31860 max)
[   10.502204] ctnetlink v0.93: registering with nfnetlink.
[   10.507541] ip_set: protocol 6
[   10.510822] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.516262] TCP cubic registered
[   10.519609] NET: Registered protocol family 10
[   10.524776] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   10.530284] IPv6 over IPv4 tunneling driver
[   10.535034] NET: Registered protocol family 17
[   10.539717] 8021q: 802.1Q VLAN Support v1.8
[   10.544378] sctp: Hash tables configured (established 16384 bind 32768)
[   10.551195] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6
[   10.558883] ThumbEE CPU extension supported.
[   10.563699] registered taskstats version 1
[   10.568845] UBI: attaching mtd5 to ubi0
[   10.572720] UBI: physical eraseblock size:   1048576 bytes (1024 KiB)
[   10.579173] UBI: logical eraseblock size:    1040384 bytes
[   10.584674] UBI: smallest flash I/O unit:    4096
[   10.589386] UBI: VID header offset:          4096 (aligned 4096)
[   10.595407] UBI: data offset:                8192
[   10.680566] UBI: max. sequence number:       2
[   10.690192] UBI: attached mtd5 to ubi0
[   10.693971] UBI: MTD device name:            "rootfs"
[   10.699031] UBI: MTD device size:            128 MiB
[   10.704009] UBI: number of good PEBs:        126
[   10.708634] UBI: number of bad PEBs:         2
[   10.713088] UBI: number of corrupted PEBs:   0
[   10.717538] UBI: max. allowed volumes:       128
[   10.722167] UBI: wear-leveling threshold:    4096
[   10.726878] UBI: number of internal volumes: 1
[   10.731331] UBI: number of user volumes:     1
[   10.735781] UBI: available PEBs:             0
[   10.740230] UBI: total number of reserved PEBs: 126
[   10.745119] UBI: number of PEBs reserved for bad PEB handling: 2
[   10.751140] UBI: max/mean erase counter: 1/0
[   10.755416] UBI: image sequence number:  971844588
[   10.760223] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[   10.766707] md: Waiting for all devices to be available before autodetect
[   10.773521] md: If you don't use raid, use raid=noautodetect
[   10.779401] UBI: background thread "ubi_bgt0d" started, PID 465
[   10.785690] md: Autodetecting RAID arrays.
[   10.789796] md: Scanned 0 and added 0 devices.
[   10.794258] md: autorun ...
[   10.797055] md: ... autorun DONE.
[   15.387887] UBIFS: static UBI volume - read-only mode
[   15.729095] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[   15.735139] UBIFS: mounted read-only
[   15.738723] UBIFS: file system size:   114442240 bytes (111760 KiB, 109 MiB, 110 LEBs)
[   15.746663] UBIFS: journal size:       12550144 bytes (12256 KiB, 11 MiB, 13 LEBs)
[   15.754253] UBIFS: media format:       w4/r0 (latest is w4/r0)
[   15.760096] UBIFS: default compressor: lzo
[   15.764203] UBIFS: reserved for root:  0 bytes (0 KiB)
[   15.771017] VFS: Mounted root (ubifs filesystem) readonly on device 0:15.
[   15.778801] devtmpfs: mounted
[   15.782036] Freeing init memory: 160K
[   15.785706] 
[   16.671879] eth0: link up
[   16.674515] Port 0: Link-up, Full-duplex, Speed-1000Mbps.
[   16.681556] Port 1: Link-down
[   16.686526] Port 2: Link-down
[   16.691540] Port 3: Link-down
[   16.705209] pool #1: pkt_size=1536, buf_size=1632 - 8192 of 8192 buffers added
[   16.715048] eth0: started (on switch)
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[   19.955924] UBI: attaching mtd6 to ubi1
[   19.959775] UBI: physical eraseblock size:   1048576 bytes (1024 KiB)
[   19.966256] UBI: logical eraseblock size:    1040384 bytes
[   19.971757] UBI: smallest flash I/O unit:    4096
[   19.976469] UBI: VID header offset:          4096 (aligned 4096)
[   19.982490] UBI: data offset:                8192
[   20.554137] UBI: max. sequence number:       26
[   20.564972] UBI: attached mtd6 to ubi1
[   20.568732] UBI: MTD device name:            "rootfs_data"
[   20.574253] UBI: MTD device size:            864 MiB
[   20.579226] UBI: number of good PEBs:        863
[   20.583860] UBI: number of bad PEBs:         1
[   20.588309] UBI: number of corrupted PEBs:   0
[   20.592764] UBI: max. allowed volumes:       128
[   20.597388] UBI: wear-leveling threshold:    4096
[   20.602103] UBI: number of internal volumes: 1
[   20.606554] UBI: number of user volumes:     1
[   20.611011] UBI: available PEBs:             0
[   20.615460] UBI: total number of reserved PEBs: 863
[   20.620345] UBI: number of PEBs reserved for bad PEB handling: 8
[   20.626366] UBI: max/mean erase counter: 1/0
[   20.630647] UBI: image sequence number:  1816790799
[   20.635538] UBI: background thread "ubi_bgt1d" started, PID 779
UBI device number 1, total 863 LEBs (897851392 bytes, 856.3 MiB), available 0 LEBs (0 bytes), LEB size 1040384 bytes (1016.0 KiB)
[   20.823685] UBIFS: recovery needed
[   21.393724] UBIFS: recovery completed
[   21.397409] UBIFS: mounted UBI device 1, volume 0, name "rootfs_data"
[   21.403875] UBIFS: file system size:   876003328 bytes (855472 KiB, 835 MiB, 842 LEBs)
[   21.411813] UBIFS: journal size:       33292288 bytes (32512 KiB, 31 MiB, 32 LEBs)
[   21.419397] UBIFS: media format:       w4/r0 (latest is w4/r0)
[   21.425245] UBIFS: default compressor: lzo
[   21.429348] UBIFS: reserved for root:  4952683 bytes (4836 KiB)
switching to ubifs rootfs_data
- init -
[   21.606345] eth0: stopped

Please press Enter to activate this console. [   22.009791] Loading modules backported from Linux version master-2014-01-23-0-g62c147d
[   22.017759] Backport generated by backports.git backports-20140124-0-g1256d3e
[   22.055874] cfg80211: Calling CRDA to update world regulatory domain
[   22.063547] cfg80211: World regulatory domain updated:
[   22.068699] cfg80211:  DFS Master region: unset
[   22.073087] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   22.081472] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   22.089231] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   22.096995] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   22.104759] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[   22.112522] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[   22.120281] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[   22.460524] ieee80211 phy0: Atheros AR9300 Rev:3 mem=0xe1500000, irq=62
[   22.497220] dm_crypt using the OCF package.
[   22.638468] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   22.688934] NET: Registered protocol family 24
[   22.849073] xt_time: kernel timezone is -0000
[   23.110262] usbcore: registered new interface driver cdc_acm
[   23.115970] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   23.143413] usbcore: registered new interface driver usbserial
[   23.149291] USB Serial support registered for generic
[   23.155507] usbcore: registered new interface driver usbserial_generic
[   23.162070] usbserial: USB Serial Driver core
[   23.174298] USB Serial support registered for Sierra USB modem
[   23.180202] usbcore: registered new interface driver sierra
[   23.185813] sierra: v.1.7.40:USB Driver for Sierra Wireless USB modems
[   23.199961] usbcore: registered new interface driver sierra_net
[   23.213079] usbcore: registered new interface driver ums-alauda
[   23.225653] usbcore: registered new interface driver ums-cypress
[   23.238721] usbcore: registered new interface driver ums-datafab
[   23.251692] usbcore: registered new interface driver ums-freecom
[   23.264846] usbcore: registered new interface driver ums-isd200
[   23.277823] usbcore: registered new interface driver ums-jumpshot
[   23.290622] usbcore: registered new interface driver ums-karma
[   23.303987] usbcore: registered new interface driver ums-sddr09
[   23.316991] usbcore: registered new interface driver ums-sddr55
[   23.342818] USB Serial support registered for GSM modem (1-port)
[   23.348948] usbcore: registered new interface driver option
[   23.354562] option: v0.7.2:USB Driver for GSM modems
[   23.367338] USB Serial support registered for Qualcomm USB modem
[   23.374148] usbcore: registered new interface driver qcserial
[   23.399129] fuse init (API version 7.17)
[   25.634221] eth0: link up
[   25.636855] Port 0: Link-up, Full-duplex, Speed-1000Mbps.
[   25.644489] Port 1: Link-down
[   25.649458] Port 2: Link-down
[   25.654429] Port 3: Link-down
[   25.659191] eth0: started (on switch)
[   25.784366] device eth0 entered promiscuous mode
[   25.797035] br-lan: port 1(eth0) entering forwarding state
[   25.802564] br-lan: port 1(eth0) entering forwarding state
[   25.820368] Port 4: Link-down
[   25.824828] eth1: started (on switch)
[   25.861072] ADDRCONF(NETDEV_UP): eth1: link is not ready
[   26.630757] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   27.800651] br-lan: port 1(eth0) entering forwarding state
Post #424
digitalgeek
21 Jun 2014, 16:23

Has anyone noticed any problems with ipv6... I was experiencing a lot of crash, and I would loose connectivity to only certain devices. After disabling ipv6, things seem more stable.

Post #425
fcecamor
21 Jun 2014, 19:15
digitalgeek wrote:

Has anyone noticed any problems with ipv6... I was experiencing a lot of crash, and I would loose connectivity to only certain devices. After disabling ipv6, things seem more stable.

How did you disable ipv6?